«Picture_Description» is depicted

Product Specification
Series: ET60S / ET60T EXTreme Ten60Power™ 60 Amp Signal/Power Combo Connector
ET60S Series – Socket, Right Angle Orientation
ET60T Series – Terminal, Right Angle Orientation
Other configurations available for:
Vertical applications (Through-hole / Press Fit)
See www.samtec.com for more information.
Revision: C
Date: November 3, 2014
Page 1
© Samtec, Inc.
Product Specification
Series: ET60S / ET60T EXTreme Ten60Power™ 60 Amp Signal/Power Combo Connector
1.0 SCOPE
1.1 This specification covers performance, testing and quality requirements for Samtec ET60S/ET60T Series EXTreme
Ten60Power™ .100” (2,54 mm) Signal / .217” (5,50 mm) Power Combo Connector. All information contained in this
specification is for a Right Angle Socket / Right Angle terminal coplanar mated configuration unless otherwise noted.
Vertical Socket / Right Angle terminal mated configuration is available on www.samtec.com.
2.0 DETAILED INFORMATION
2.1 Product prints, footprints, catalog pages, test reports and other specific, detailed information can be found at
www.samtec.com?ET60S and www.samtec.com?ET60T.
3.0 TESTING
3.1 Current Rating: 60A (Power) / 24A (Signal)
3.1.1 Current Carrying Capacity: tested per EIA-364-70
3.1.2 Current Cycling: tested per EIA-364-55
3.2 Voltage Rating: 300 VAC
3.3 Operating Temperature Range: -40°C to +125°C
3.4 Electrical:
ITEM
TEST CONDITION
REQUIREMENT
STATUS
Withstanding Voltage
EIA-364-20 (No Flashover,
Sparkover, or Breakdown)
900 VAC
Pass
Insulation Resistance
EIA-364-21 (1000 MΩ
minimum)
10,000 MΩ
Pass
Contact Resistance
(LLCR)
EIA-364-23
Δ 15 mΩ maximum
(Samtec defined)/ No damage
Pass
REQUIREMENT
STATUS
3.5 Mechanical:
ITEM
TEST CONDITION
Durability
EIA-364-09C
100 cycles
Pass
Random Vibration
EIA-364-28 Condition V, Letter B
7.56 G 'RMS', 50 to 2000 Hz, 2
hours per axis, 3 axis total , PSD
0.04
Visual Inspection: No Damage
LLCR: Δ 15 mΩ maximum
Event Detection: No interruption >
50 microsecond
Pass
Mechanical Shock
EIA-364-27 100 G, 6
milliseconds, sawtooth wave,
11.3 fps, 3 shocks/direction, 3
axis (18 total shocks)
Visual Inspection: No Damage
LLCR: Δ 15 mΩ maximum
Event Detection: No interruption >
50 microsecond
Pass
Normal Force
EIA-364-04
30 grams minimum for gold
interface
Pass
Revision: C
Date: November 3, 2014
Page 2
© Samtec, Inc.
Product Specification
Series: ET60S / ET60T EXTreme Ten60Power™ 60 Amp Signal/Power Combo Connector
3.6 Environmental:
ITEM
TEST CONDITION
REQUIREMENT
STATUS
Thermal Shock
EIA-364-32
Thermal Cycles: 100 (30 minute dwell)
Hot Temp: +85°C
Cold Temp: -55°C
Hot/Cold Transition: Immediate
Visual Inspection: No Damage
LLCR: Δ 15 mΩ
DWV: 900 VAC
IR: >10,000 MΩ
Pass
Thermal Aging
(Temp Life)
EIA-364-17
Test Condition 4 @ 105°C
Condition B for 250 hours
Visual Inspection: No Damage
LLCR: Δ 15 mΩ
DWV: 900 VAC
IR: >10,000 MΩ
Pass
Cyclic Humidity
EIA-364-31
Test Temp: +25°C to +65°C
Relative Humidity: 90 to 95%
Test Duration: 240 hours
Visual Inspection: No Damage
LLCR: Δ 15 mΩ
DWV: 900 VAC
IR: >10,000 MΩ
Pass
Gas Tight
EIA-364-36
Gas Exposure: Nitric Acid Vapor
Duration: 60 min.
Drying Temp.: 50°C +/- 3°C
Measurements: Within 1 hour of
Exposure
LLCR: Δ 15 mΩ
Pass
4.0 MATED SYSTEM
Mated view information can be found at link below:
http://www.samtec.com/documents/webfiles/cpdf/ET60X%20Mated%20Document.pdf
Revision: C
Date: November 3, 2014
Page 3
© Samtec, Inc.
Product Specification
Series: ET60S / ET60T EXTreme Ten60Power™ 60 Amp Signal/Power Combo Connector
5.0 POLARIZING FEATURES
Revision: C
Date: November 3, 2014
Page 4
© Samtec, Inc.
Product Specification
Series: ET60S / ET60T EXTreme Ten60Power™ 60 Amp Signal/Power Combo Connector
6.0 PROCESSING RECOMMENDATIONS
6.1 Mating Alignment Requirements:
6.1.1
Revision: C
Maximum guidance/capture in applications where at least one half of the interface is free to float.
Date: November 3, 2014
Page 5
© Samtec, Inc.
Product Specification
Series: ET60S / ET60T EXTreme Ten60Power™ 60 Amp Signal/Power Combo Connector
6.1.2
The parts can be rigidly misaligned by no more than 1,38 mm in the X- and 1,90 mm in the Y-direction to
ensure a good mate.
6.2 Mating Angle Requirements: The connector can be zippered in the longitudinal direction only.
6.2.1
Revision: C
Date: November 3, 2014
Page 6
© Samtec, Inc.
Product Specification
Series: ET60S / ET60T EXTreme Ten60Power™ 60 Amp Signal/Power Combo Connector
6.2.2
6.3 Intermateability: Information on Samtec’s Intermateability with Molex is available at
http://www.samtec.com/Documents/WebFiles/TestRpt/234464_report_rev_1.pdf
7.0 ADDITIONAL RESOURCES
7.1 For additional mechanical testing or product information, contact our Customer Engineering Support Group at
[email protected]
7.2 For additional information on high speed performance testing, contact our Signal Integrity Group at
[email protected]
7.3 For additional processing information, contact our Interconnect Processing Group at [email protected].
7.4 For RoHS, REACH or other environmental compliance information, contact our Product Environmental
Compliance Group at [email protected]
* EXTreme Ten60Power is a trademark of Molex Incorporated
Revision: C
Date: November 3, 2014
Page 7
© Samtec, Inc.