Product Specification Series: I2SS / T2I 2,00 mm (.0787”) Single Row Discrete Wire IDC System Cable Assembly Housing, Socket / Terminal Strip I2SS Series – Cable Assembly Housing, Socket T2I Series – Terminal Strip See www.samtec.com for more information. Revision: A Date: September 4, 2014 Page 1 © Samtec, Inc. Product Specification Series: I2SS / T2I 2,00 mm (.0787”) Single Row Discrete Wire IDC System Cable Assembly Housing, Socket / Terminal Strip 1.0 SCOPE 1.1 This specification covers performance, testing and quality requirements for Samtec’s I2SS/T2I Series 2,00mm (.0787”) Single Row Discrete Wire IDC system Cable Assembly Housing, Socket and Terminal Strip Connectors. All information contained in this specification is for a 5 positions configuration unless otherwise noted. 2.0 DETAILED INFORMATION 2.1 Product prints, footprints, catalog pages, test reports and other specific, detailed information can be found at www.samtec.com?I2SS and www.samtec.com?T2I. 3.0 TESTING 3.1 Current Rating: 4.7 A (One Pin Powered) 3.2 Voltage Rating: 250 VAC 3.3 Operating Temperature Range: -55°C to +105°C (Connector Only, Wire used may decrease the operating temperature range) 3.4 Operating Humidity Range: 90% to 95% (Per EIA-364-31) 3.5 Electrical: ITEM TEST CONDITION REQUIREMENT STATUS Withstanding Voltage EIA-364-20 (No Flashover, Sparkover, or Breakdown) 750 VAC Pass Insulation Resistance EIA-364-21 (1000 MΩ minimum) 1,000 MΩ Pass Contact Resistance (LLCR) EIA-364-23 Δ 15 mΩ maximum (Samtec defined)/ No damage Pass REQUIREMENT STATUS 3.6 Mechanical: ITEM TEST CONDITION Durability EIA-364-09C 100 cycles Pass Random Vibration EIA-364-28 Condition V, Letter B 7.56 G 'RMS', 50 to 2000 Hz, 2 hours per axis, 3 axis total , PSD 0.04 Visual Inspection: No Damage LLCR: Δ 15 mΩ maximum Pass Mechanical Shock EIA-364-27 100 G, 6 milliseconds, sawtooth wave, 11.3 fps, 3 shocks/direction, 3 axis (18 total shocks) Visual Inspection: No Damage LLCR: Δ 15 mΩ maximum Pass Normal Force EIA-364-04 30 grams minimum for gold interface Pass Revision: A Date: September 4, 2014 Page 2 © Samtec, Inc. Product Specification Series: I2SS / T2I 2,00 mm (.0787”) Single Row Discrete Wire IDC System Cable Assembly Housing, Socket / Terminal Strip 3.7 Environmental: ITEM REQUIREMENT STATUS Thermal Shock EIA-364-32 Thermal Cycles: 100 (30 minute dwell) Hot Temp: +85°C Cold Temp: -55°C Hot/Cold Transition: Immediate Visual Inspection: No Damage LLCR: Δ 15 mΩ DWV: 750 VAC IR: >1,000 MΩ Pass Thermal Aging (Temp Life) EIA-364-17 Test Condition 4 @ 105°C Condition B for 250 hours Visual Inspection: No Damage LLCR: Δ 15 mΩ DWV: 750 VAC IR: >1,000 MΩ Pass Cyclic Humidity EIA-364-31 Test Temp: +25°C to +65°C Relative Humidity: 90 to 95% Test Duration: 240 hours Visual Inspection: No Damage LLCR: Δ 15 mΩ DWV: 750 VAC IR: >1,000 MΩ Pass Gas Tight EIA-364-36 Gas Exposure: Nitric Acid Vapor Duration: 60 min. Drying Temp.: 50°C +/- 3°C Measurements: Within 1 hour of Exposure LLCR: Δ 15 mΩ Pass Revision: A TEST CONDITION Date: September 4, 2014 Page 3 © Samtec, Inc. Product Specification Series: I2SS / T2I 2,00 mm (.0787”) Single Row Discrete Wire IDC System Cable Assembly Housing, Socket / Terminal Strip 4.0 MATED SYSTEM Mated view information can be found at link below: http://www.samtec.com/documents/webfiles/cpdf/I2SS-T2I%20MATED%20DOCUMENT-MKT.pdf 5.0 POLARIZING FEATURES Revision: A Date: September 4, 2014 Page 4 © Samtec, Inc. Product Specification Series: I2SS / T2I 2,00 mm (.0787”) Single Row Discrete Wire IDC System Cable Assembly Housing, Socket / Terminal Strip 6.0 LATCH FEATURES: To disengage cable from socket, first, fully seat connector; second fully depress latch release and third, pull straight back with latch released depressed. 7.0 PROCESSING RECOMMENDATIONS 7.1 Mating Angle Requirements: Cable must be axially aligned to connector when mated and un-mated. 7.1.1 Revision: A Date: September 4, 2014 Page 5 © Samtec, Inc. Product Specification Series: I2SS / T2I 2,00 mm (.0787”) Single Row Discrete Wire IDC System Cable Assembly Housing, Socket / Terminal Strip 8.0 APPLICATION 8.1 Insert cables into I2SS assembly. 8.1.1 8.2 Press I2SS with Plier. 8.2.1 Revision: A Date: September 4, 2014 Page 6 © Samtec, Inc. Product Specification Series: I2SS / T2I 2,00 mm (.0787”) Single Row Discrete Wire IDC System Cable Assembly Housing, Socket / Terminal Strip 8.2.2 9.0 ADDITIONAL RESOURCES 9.1 For additional mechanical testing or product information, contact our Customer Engineering Support Group at [email protected] 9.2 For additional information on high speed performance testing, contact our Signal Integrity Group at [email protected] 9.3 For additional processing information, contact our Interconnect Processing Group at [email protected]. 9.4 For RoHS, REACH or other environmental compliance information, contact our Product Environmental Compliance Group at [email protected] Revision: A Date: September 4, 2014 Page 7 © Samtec, Inc.