Design Qualification Test Report LPHS / Card LPHS-08-32

Project Number: Design Qualification Test Report
Tracking Code: 259655_Report_Rev_1
Requested by: Leo Lee
Date: 9/4/2015
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS /Card
Tech: Peter Chen
Test Start: 06/03/2013
Test Completed: 07/05/2013
Design Qualification Test Report
LPHS / Card
LPHS-08-32-L-RT1-GP/Edge Card
Page 1 of 54
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
REVISION HISTORY
DATA
REV.NUM.
6/27/2013
1
DESCRIPTION
Initial Issue
Page 2 of 54
ENG
PC
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
CERTIFICATION
All instruments and measuring equipment were calibrated to National Institute for Standards and Technology (NIST)
traceable standards according to IS0 10012-l and ANSI/NCSL 2540-1, as applicable.
All contents contained herein are the property of Samtec. No portion of this report, in part or in full shall be
reproduced without prior written approval of Samtec.
SCOPE
To perform the following tests: Design Qualification Test, Please see test plan.
APPLICABLE DOCUMENTS
Standards: EIA Publication 364
TEST SAMPLES AND PREPARATION
1)
2)
3)
4)
5)
6)
7)
8)
9)
All materials were manufactured in accordance with the applicable product specification.
All test samples were identified and encoded to maintain traceability throughout the test sequences.
After soldering, the parts to be used for LLCR and DWV/IR testing were cleaned according to TLWI-0001.
Either an automated cleaning procedure or an ultrasonic cleaning procedure may be used.
The automated procedure is used with aqueous compatible soldering materials.
Parts not intended for testing LLCR and DWV/IR are visually inspected and cleaned if necessary.
Any additional preparation will be noted in the individual test sequences.
Solder Information: Lead free
Samtec Test PCBs used: PCB-104070-TST
Page 3 of 54
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
FLOWCHARTS
Gas Tight
TEST
STEP
01
GROUP A1
8 boards
0.056'' thick edge card(Min)
LLCR-1
Gas Tight
02
03
LLCR-2
Gas Tight = EIA-364-36A
LLCR = EIA-364-23, LLCR
20 mV Max, 100 mA Max
Use Keithley 580 or 3706 in 4 wire dry circuit mode
Thermal Aging
TEST
STEP
01
GROUP A1
8 Boards
Thermal Aging (Mated)
0.056'' thick edge card(Min)
Contact Gaps
GROUP A1
8 Boards
Thermal Aging (Mated)
0.068'' thick edge card(Max)
Contact Gaps
02
Measure & Record PCB Thickness
Measure & Record PCB Thickness
03
Forces - Mating / Unmating
Forces - Mating / Unmating
04
LLCR-1
LLCR-1
05
Thermal Aging
(Mated and Undisturbed)
Thermal Aging
(Mated and Undisturbed)
06
LLCR-2
LLCR-2
07
Forces - Mating / Unmating
Forces - Mating / Unmating
08
Contact Gaps
Contact Gaps
Thermal Aging = EIA-364-17, Test Condition 4 (105°C)
Time Condition 'B' (250 Hours)
Mating / Unmating Forces = EIA-364-13
Contact Gaps / Height - No standard method. Usually measured optically.
Gaps to be taken on a minimum of 20% of each part tested
LLCR = EIA-364-23, LLCR
20 mV Max, 100 mA Max
Use Keithley 580 or 3706 in 4 wire dry circuit mode
Page 4 of 54
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
FLOWCHARTS Continued
Durability/Mating/Unmating/Gaps
TEST
01
GROUP B1
8 Boards
(largest position submitted)
0.056'' thick edge card(Min)
Contact Gaps
GROUP B1
8 Boards
(largest position submitted)
0.068'' thick edge card(Max)
Contact Gaps
GROUP B2
8 Boards
(middle position submitted)
0.068'' thick edge card(Max)
Contact Gaps
GROUP B3
8 Boards
(smallest position submitted)
0.068'' thick edge card(Max)
Contact Gaps
02
Measure & Record PCB Thickness
Measure & Record PCB Thickness
Measure & Record PCB Thickness
Measure & Record PCB Thickness
Forces - Mating / Unmating
STEP
03
LLCR-1
LLCR-1
Forces - Mating / Unmating
04
Forces - Mating / Unmating
Forces - Mating / Unmating
25 Cycles
25 Cycles
05
25 Cycles
Forces - Mating / Unmating
25 Cycles
Forces - Mating / Unmating
Forces - Mating / Unmating
25 Cycles (50 Total)
Forces - Mating / Unmating
25 Cycles (50 Total)
Forces - Mating / Unmating
06
07
25 Cycles (50 Total)
25 Cycles (50 Total)
Forces - Mating / Unmating
08
Forces - Mating / Unmating
Forces - Mating / Unmating
25 Cycles (75 Total)
25 Cycles (75 Total)
09
25 Cycles (75 Total)
25 Cycles (75 Total)
Forces - Mating / Unmating
Forces - Mating / Unmating
10
Forces - Mating / Unmating
Forces - Mating / Unmating
25 Cycles (100 Total)
25 Cycles (100 Total)
11
12
25 Cycles (100 Total)
25 Cycles (100 Total)
Forces - Mating / Unmating
Forces - Mating / Unmating
Forces - Mating / Unmating
Forces - Mating / Unmating
14
Clean w/Compressed Air
Contact Gaps
Clean w/Compressed Air
Contact Gaps
15
LLCR-2
LLCR-2
16
Thermal Shock
(Mated and Undisturbed)
Thermal Shock
(Mated and Undisturbed)
17
LLCR-3
LLCR-3
19
Cyclic Humidity
(Mated and Undisturbed)
LLCR-4
Cyclic Humidity
(Mated and Undisturbed)
LLCR-4
20
Forces - Mating / Unmating
Forces - Mating / Unmating
13
18
Thermal Shock = EIA-364-32, Table II, Test Condition I:
o
o
Humidity-55 C to +85 C 1/2 hour dwell, 100 cycles
and Method III (+25°C to +65°C @ 90% RH to 98% RH)
Mating / ambient pre-condition and delete steps 7a and 7b
Contact Gaps / Height - No standard method. Usually measured optically.
LLCR = EGaps to be taken on a minimum of 20% of each part tested
20 mV Max, 100 mA Max
Use Keithley 580 or 3706 in 4 wire dry circuit mode
Page 5 of 54
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
FLOWCHARTS Continued
IR & DWV
TEST
GROUP A1
STEP
2 Mated Sets
01
Break Down
Pin-to-Pin
(Signal Pin)
0.056'' thick edge card(Min)
GROUP A2
2 Unmated of Part #
Being Tested
Break Down
Pin-to-Pin
(Signal Pin)
0.056'' thick edge card(Min)
DWV/Break Down Voltage
DWV/Break Down Voltage
GROUP A3
GROUP B1
2 Unmated of Mating Part #
2 Mated Sets
Break Down
Pin-to-Pin
(Signal Pin)
0.056'' thick edge card(Min)
Pin-to-Pin
(Signal Pin)
0.056'' thick edge card(Min)
DWV/Break Down Voltage
IR & DW V at test voltage
(on both mated sets and on each
connector unmated)
02
Thermal Shock
(Mated and Undisturbed)
03
IR & DW V at test voltage
(on both mated sets and on each
connector unmated)
04
Cyclic Humidity
(Mated and Undisturbed)
05
IR & DW V at test voltage
(on both mated sets and on each
connector unmated)
TEST
GROUP C1
STEP
2 Mated Sets
01
Break Down
Row-to-Row
(Signal Pin)
0.056'' thick edge card(Min)
GROUP C2
2 Unmated of Part #
Being Tested
Break Down
Row-to-Row
(Signal Pin)
0.056'' thick edge card(Min)
DWV/Break Down Voltage
DWV/Break Down Voltage
GROUP C3
GROUP D1
2 Unmated of Mating Part #
2 Mated Sets
Break Down
Row-to-Row
(Signal Pin)
0.056'' thick edge card(Min)
Row-to-Row
(Signal Pin)
0.056'' thick edge card(Min)
DWV/Break Down Voltage
IR & DW V at test voltage
(on both mated sets and on each
connector unmated)
02
Thermal Shock
(Mated and Undisturbed)
03
IR & DW V at test voltage
(on both mated sets and on each
connector unmated)
04
Cyclic Humidity
(Mated and Undisturbed)
05
IR & DW V at test voltage
(on both mated sets and on each
connector unmated)
Page 6 of 54
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
FLOWCHARTS Continued
TEST
GROUP E1
STEP
2 Mated Sets
01
Break Down
Power-to-Power
0.056'' thick edge card(Min)
GROUP E2
2 Unmated of Part #
Being Tested
Break Down
Power-to-Power
0.056'' thick edge card(Min)
DWV/Break Down Voltage
DWV/Break Down Voltage
GROUP E3
GROUP F1
2 Unmated of Mating Part #
2 Mated Sets
Break Down
Power-to-Power
0.056'' thick edge card(Min)
Power-to-Power
0.056'' thick edge card(Min)
DWV/Break Down Voltage
IR & DW V at test voltage
(on both mated sets and on each
connector unmated)
02
Thermal Shock
(Mated and Undisturbed)
03
IR & DW V at test voltage
(on both mated sets and on each
connector unmated)
04
Cyclic Humidity
(Mated and Undisturbed)
05
IR & DW V at test voltage
(on both mated sets and on each
connector unmated)
TEST
GROUP G1
STEP
2 Mated Sets
01
GROUP G3
GROUP H1
2 Unmated of Mating Part #
2 Mated Sets
Break Down
Signal-to-Power
0.056'' thick edge card(Min)
GROUP G2
2 Unmated of Part #
Being Tested
Break Down
Signal-to-Power
0.056'' thick edge card(Min)
Break Down
Signal-to-Power
0.056'' thick edge card(Min)
Signal-to-Power
0.056'' thick edge card(Min)
DWV/Break Down Voltage
DWV/Break Down Voltage
DWV/Break Down Voltage
02
03
04
05
IR & DW V at test voltage
(on both mated sets and on each
connector unmated)
Thermal Shock
(Mated and Undisturbed)
IR & DW V at test voltage
(on both mated sets and on each
connector unmated)
Cyclic Humidity
(Mated and Undisturbed)
IR & DW V at test voltage
(on both mated sets and on each
connector unmated)
DWV on Group B1 to be performed at Test Voltage
DWV test voltage is equal to 75% of the lowest break down voltage from Groups A1, A2 or A3
Thermal Shock = EIA-364-32, Table II, Test Condition I:
o
o
-55 C to +85 C 1/2 hour dwell, 100 cycles
Humidity = EIA-364-31, Test Condition B (240 Hours)
and Method III (+25°C to +65°C @ 90% RH to 98% RH)
ambient pre-condition and delete steps 7a and 7b
IR = EIA-364-21
DWV = EIA-364-20, Test Condition 1
Page 7 of 54
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
FLOWCHARTS Continued
Normal Force
TEST
01
GROUP A1
C-378-01 (Signal)
Individual Contacts(10
min)
0.068'' thick edge
card(Max)
Contact Gaps
02
Setup Approved
03
Normal Force
(in the body and soldered
on PCB unless otherwise
specified)
STEP
GROUP A2
GROUP B1
C-378-01 (Signal)
C-377-01 (Power)
Individual Contacts(10 Individual Contacts(10
min)
min)
0.068'' thick edge
0.068'' thick edge
card(Max)
card(Max)
Contact Gaps
Contact Gaps
Thermal Aging
(Mated and
Setup Approved
Undisturbed)
Contact Gaps
GROUP B2
C-377-01 (Power)
Individual Contacts(10
min)
0.068'' thick edge
card(Max)
Contact Gaps
GROUP C1
C-377-02 (Power)
Individual Contacts(10
min)
0.068'' thick edge
card(Max)
Contact Gaps
GROUP C2
C-377-02(Power)
Individual Contacts(10
min)
0.068'' thick edge
card(Max)
Contact Gaps
Thermal Aging
(Mated and Undisturbed)
Setup Approved
Thermal Aging
(Mated and Undisturbed)
Contact Gaps
Normal Force
(in the body and soldered
on PCB unless otherwise
specified)
Contact Gaps
Normal Force
(in the body and soldered
on PCB unless otherwise
specified)
04
Setup Approved
Setup Approved
Setup Approved
05
Normal Force
(in the body and
soldered on PCB unless
otherwise specified)
Normal Force
(in the body and soldered
on PCB unless otherwise
specified)
Normal Force
(in the body and
soldered on PCB unless
otherwise specified)
Thermal Aging = EIA-364-17, Test Condition 4 (105°C)
Time Condition 'B' (250 Hours)
Normal Force = EIA-364-04
(Perpendicular) Displacement Force = 12.7 mm/min ± 6 mm/min
Spec is 50 N @ 1 mm displacement
Contact Gaps / Height - No standard method. Usually measured optically
Gaps to be taken on a minimum of 20% of each part tested
Page 8 of 54
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
FLOWCHARTS Continued
Current Carrying Capacity - Power Pins
TEST
STEP
GROUP A1
3 Mated Assemblies
2 Contact Powered
0.056'' thick edge
card(Min)
GROUP A2
3 Mated Assemblies
4 Contacts Powered
0.056'' thick edge
card(Min)
GROUP A3
3 Mated Assemblies
6 Contacts Powered
0.056'' thick edge
card(Min)
GROUP A4
3 Mated Assemblies
All Contacts Powered
0.056'' thick edge
card(Min)
01
CCC
CCC
CCC
CCC
GROUP D1
3 Mated Assemblies
GROUP D2
3 Mated Assemblies
GROUP D3
3 Mated Assemblies
GROUP D4
3 Mated Assemblies
GROUP D5
3 Mated Assemblies
2 Pins Powered
0.056'' thick edge
card(Min)
4 Pins Powered
0.056'' thick edge
card(Min)
6 Pins Powered
0.056'' thick edge
card(Min)
8 Pins Powered
0.056'' thick edge
card(Min)
All Contacts Powered
0.056'' thick edge
card(Min)
CCC
CCC
CCC
CCC
CCC
Current Carrying Capacity - Singal Pins
TEST
STEP
01
Current Carrying Capacity - Power and Signal Pins
TEST
STEP
GROUP E1
3 Mated Assemblies
Signal Pins @ 1/2 rated
current from Group D5
Power Pins - All
Contacts Powered
0.056'' thick edge
card(Min)
01
CCC
(TIN PLATING) - Tabulate calculated current at RT, 65°C, 75°C and 95°C
after derating 20% and based on 105°C
(GOLD PLATING) - Tabulate calculated current at RT, 85°C, 95°C and 115°C
after derating 20% and based on 125°C
CCC, Temp rise = EIA-364-70
Page 9 of 54
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
FLOWCHARTS Continued
Mechanical Shock / Vibration / LLCR
TEST
STEP
01
GROUP A1
8 boards
0.056'' thick edge card(Min)
LLCR-1
GROUP A1
8 boards
0.068'' thick edge card(Max)
LLCR-1
02
03
Shock
Shock
Vibration
Vibration
04
LLCR-2
LLCR-2
Mechanical Shock = EIA 364-27 Half Sine,
100 g's, 6 milliSeconds (Condition "C") each axis
Vibration = EIA 364-28, Random Vibration
7.56 g RMS, Condition VB --- 2 hours/axis
LLCR = EIA-364-23, LLCR
20 mV Max, 100 mA Max
Use Keithley 580 or 3706 in 4 wire dry circuit mode
Shock / Vibration / nanoSecond Event Detection
TEST
STEP
GROUP A1
60 Points
0.056'' thick edge card(Min)
01
Event Detection, Shock
02
Event Detection, Vibration
Mechanical Shock = EIA 364-27 Half Sine,
100 g's, 6 milliSeconds (Condition "C") each axis
Vibration = EIA 364-28, Random Vibration
7.56 g RMS, Condition VB --- 2 hours/axis
Event detection requirement during Shock / Vibration is 50 nanoseconds minimum
Page 10 of 54
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
ATTRIBUTE DEFINITIONS
The following is a brief, simplified description of attributes.
THERMAL SHOCK:
1)
2)
3)
4)
5)
6)
EIA-364-32, Thermal Shock (Temperature Cycling) Test Procedure for Electrical Connectors.
Test Condition 1: -55°C to +85°C
Test Time: ½ hour dwell at each temperature extreme
Number of Cycles: 100
All test samples are pre-conditioned at ambient.
All test samples are exposed to environmental stressing in the mated condition.
THERMAL:
1)
2)
3)
4)
5)
EIA-364-17, Temperature Life with or without Electrical Load Test Procedure for Electrical Connectors.
Test Condition 4 at 105° C.
Test Time Condition B for 250 hours.
All test samples are pre-conditioned at ambient.
All test samples are exposed to environmental stressing in the mated condition.
HUMIDITY:
1)
2)
3)
4)
5)
Reference document: EIA-364-31, Humidity Test Procedure for Electrical Connectors.
Test Condition B, 240 Hours.
Method III, +25° C to + 65° C, 90% to 98% Relative Humidity excluding sub-cycles 7a and 7b.
All samples are pre-conditioned at ambient.
All test samples are exposed to environmental stressing in the mated condition.
MECHANICAL SHOCK (Specified Pulse):
1)
2)
3)
4)
5)
6)
7)
Reference document: EIA-364-27, Mechanical Shock Test Procedure for Electrical Connectors
Test Condition C
Peak Value: 100 G
Duration: 6 Milliseconds
Wave Form: Half Sine
Velocity: 12.3 ft/s
Number of Shocks: 3 Shocks / Direction, 3 Axis (18 Total)
VIBRATION:
1)
2)
3)
4)
5)
6)
Reference document: EIA-364-28, Vibration Test Procedure for Electrical Connectors
Test Condition V, Letter B
Power Spectral Density: 0.04 G² / Hz
G ‘RMS’: 7.56
Frequency: 50 to 2000 Hz
Duration: 2.0 Hours per axis (3 axis total)
NANOSECOND-EVENT DETECTION:
1) Reference document: EIA-364-87, Nanosecond-Event Detection for Electrical Connectors
2) Prior to test, the samples were characterized to assure the low nanosecond event being monitored will trigger
the detector.
3) After characterization it was determined the test samples could be monitored for 50 nanosecond events
Page 11 of 54
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
ATTRIBUTE DEFINITIONS
The following is a brief, simplified description of attributes.
MATING/UNMATING:
1) Reference document: EIA-364-13, Mating and Unmating Forces Test Procedure for Electrical Connectors.
2) The full insertion position was to within 0.003” to 0.004” of the plug bottoming out in the receptacle to
prevent damage to the system under test.
3) One of the mating parts is secured to a floating X-Y table to prevent damage during cycling.
NORMAL FORCE (FOR CONTACTS TESTED IN THE HOUSING):
1) Reference document: EIA-364-04, Normal Force Test Procedure for Electrical Connectors.
2) The contacts shall be tested in the connector housing.
3) If necessary, a “window” shall be made in the connector body to allow a probe to engage and deflect the
contact at the same attitude and distance (plus 0.05 mm [0.002”]) as would occur in actual use.
4) The connector housing shall be placed in a holding fixture that does not interfere with or otherwise influence
the contact force or deflection.
5) Said holding fixture shall be mounted on a floating, adjustable, X-Y table on the base of the Dillon TC2,
computer controlled test stand with a deflection measurement system accuracy of 5.0 µm (0.0002”).
6) The nominal deflection rate shall be 5 mm (0.2”)/minute.
7) Unless otherwise noted a minimum of five contacts shall be tested.
8) The force/deflection characteristic to load and unload each contact shall be repeated five times.
9) The system shall utilize the TC2 software in order to acquire and record the test data.
10) The permanent set of each contact shall be measured within the TC2 software.
11) The acquired data shall be graphed with the deflection data on the X-axis and the force data on the Y-axis
and a print out will be stored with the Tracking Code paperwork.
INSULATION RESISTANCE (IR):
To determine the resistance of insulation materials to leakage of current through or on the surface of these
materials when a DC potential is applied.
1) PROCEDURE:
a. Reference document: EIA-364-21, Insulation Resistance Test Procedure for Electrical Connectors.
b. Test Conditions:
i. Between Adjacent Contacts or Signal-to-Ground
ii. Electrification Time 2.0 minutes
iii. Test Voltage (500 VDC) corresponds to calibration settings for measuring resistances.
2) MEASUREMENTS:
3) When the specified test voltage is applied (VDC), the insulation resistance shall not be less than 5000
megohms.
Page 12 of 54
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
ATTRIBUTE DEFINITIONS
The following is a brief, simplified description of attributes.
DIELECTRIC WITHSTANDING VOLTAGE (DWV):
To determine if the sockets can operate at its rated voltage and withstand momentary over potentials due to
switching, surges, and other similar phenomenon. Separate samples are used to evaluate the effect of
environmental stresses so not to influence the readings from arcing that occurs during the measurement
process.
1) PROCEDURE:
a. Reference document: EIA-364-20, Withstanding Voltage Test Procedure for Electrical Connectors.
b. Test Conditions:
i. Between Adjacent Contacts or Signal-to-Ground
ii. Rate of Application 500 V/Sec
iii. Test Voltage (VAC) until breakdown occurs
2) MEASUREMENTS/CALCULATIONS
a. The breakdown voltage shall be measured and recorded.
b. The dielectric withstanding voltage shall be recorded as 75% of the minimum breakdown voltage.
c. The working voltage shall be recorded as one-third (1/3) of the dielectric withstanding voltage (onefourth of the breakdown voltage)..
TEMPERATURE RISE (Current Carrying Capacity, CCC):
1)
EIA-364-70, Temperature Rise versus Current Test Procedure for Electrical Connectors and Sockets.
2
2) When current passes through a contact, the temperature of the contact increases as a result of I R (resistive)
heating.
3) The number of contacts being investigated plays a significant part in power dissipation and therefore
temperature rise.
4) The size of the temperature probe can affect the measured temperature.
5) Copper traces on PC boards will contribute to temperature rise:
a. Self heating (resistive)
b. Reduction in heat sink capacity affecting the heated contacts
6) A de-rating curve, usually 20%, is calculated.
7) Calculated de-rated currents at four temperature points are reported:
c. Ambient
о
d. 85 C
о
e. 95 C
о
f. 115 C
8) Typically, neighboring contacts (in close proximity to maximize heat build up) are energized.
9) The thermocouple (or temperature measuring probe) will be positioned at a location to sense the maximum
temperature in the vicinity of the heat generation area.
10) A computer program, TR 803.exe, ensures accurate stability for data acquisition.
11) Hook-up wire cross section is larger than the cross section of any connector leads/PC board traces, jumpers,
etc.
12) Hook-up wire length is longer than the minimum specified in the referencing standard.
Page 13 of 54
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
ATTRIBUTE DEFINITIONS
The following is a brief, simplified description of attributes.
LLCR:
1) EIA-364-23, Low Level Contact Resistance Test Procedure for Electrical Connectors and Sockets.
2) A computer program, LLCR 221.exe, ensures repeatability for data acquisition.
3) The following guidelines are used to categorize the changes in LLCR as a result from stressing
a. <= +5.0 mOhms: --------------------------- Stable
b. +5.1 to +10.0 mOhms: --------------------- Minor
c. +10.1 to +15.0 mOhms: ------------------- Acceptable
d. +15.1 to +50.0 mOhms: ------------------- Marginal
e. +50.1 to +2000 mOhms: ------------------ Unstable
f. >+2000 mOhms:---------------------------- Open Failure
GAS TIGHT:
1)
2)
3)
4)
To provide method for evaluating the ability of the contacting surfaces in preventing penetration of harsh
vapors which might lead to oxide formation that may degrade the electrical performance of the contact
system.
EIA-364-23, Low Level Contact Resistance Test Procedure for Electrical Connectors and Sockets.
A computer program, LLCR 221.exe, ensures repeatability for data acquisition.
The following guidelines are used to categorize the changes in LLCR as a result from stressing
a. <= +5.0 mOhms: --------------------------- Stable
b. +5.1 to +10.0 mOhms: --------------------- Minor
c. +10.1 to +15.0 mOhms: ------------------- Acceptable
d. +15.1 to +50.0 mOhms: ------------------- Marginal
e. +50.1 to +2000 mOhms: ------------------ Unstable
f. >+2000 mOhms:---------------------------- Open Failure
Procedure:
g. Reference document: EIA-364-36, Test Procedure for Determination of Gas-Tight Characteristics
for Electrical Connectors, Sockets and/or Contact Systems.
h. Test Conditions:
i. Class II--- Mated pairs of contacts assembled to their plastic housings.
ii. Reagent grade Nitric Acid shall be used of sufficient volume to saturate the test chamber
iii. The ratio of the volume of the test chamber to the surface area of the acid shall be 10:1.
iv. The chamber shall be saturated with the vapor for at least 15 minutes before samples are
added.
v. Exposure time, 55 to 65 minutes.
vi. The samples shall be no closer to the chamber walls than 1 inches and no closer to the
surface of the acid than 3 inches.
vii. The samples shall be dried after exposure for a minimum of 1 hour.
о
viii. Drying temperature 50 C
ix. The final LLCR shall be conducted within 1 hour after drying.
Page 14 of 54
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
RESULTS
Temperature Rise, CCC at a 20% de-rating
Power pin
 CCC for a 30°C Temperature Rise --------------- 29.2 A per contact with 2 adjacent power contacts powered
 CCC for a 30°C Temperature Rise --------------- 24.9 A per contact with 4 adjacent power contacts powered
 CCC for a 30°C Temperature Rise --------------- 22.0 A per contact with 6 adjacent power contacts powered
 CCC for a 30°C Temperature Rise --------------- 20.8 A per contact with All adjacent power contacts powered
Signal pin
 CCC for a 30°C Temperature Rise --------------- 2.4 A per contact with 2 adjacent signal contacts powered
 CCC for a 30°C Temperature Rise --------------- 1.9 A per contact with 4 adjacent signal contacts powered
 CCC for a 30°C Temperature Rise --------------- 1.8 A per contact with 6 adjacent signal contacts powered
 CCC for a 30°C Temperature Rise --------------- 1.4 A per contact with 8 adjacent signal contacts powered
 CCC for a 30°C Temperature Rise --------------- 1.0 A per contact with all adjacent signal contacts powered
Power Pin powered while signal pin @ 1/2 rated current at 0.60 Amps
 CCC for a 30°C Temperature Rise --------------- 21.2 A per contact with All adjacent power contacts powered
Mating & Unmating force
Thermal aging (LPHS-08-32-L-RT1-GP/0.056” thick card)
 Initial
o Mating
 Min --------------------------------------- 7.55 Lbs
 Max--------------------------------------- 9.25 Lbs
o Unmating
 Min --------------------------------------- 6.24 Lbs
 Max--------------------------------------- 7.15 Lbs
 After thermal aging
o Mating
 Min --------------------------------------- 4.17 Lbs
 Max--------------------------------------- 5.76 Lbs
o Unmating
 Min --------------------------------------- 3.20 Lbs
 Max--------------------------------------- 4.03 Lbs
Thermal aging (LPHS-08-32-L-RT1-GP/0.068” thick card)
 Initial
o Mating
 Min --------------------------------------11.38 Lbs
 Max--------------------------------------13.77 Lbs
o Unmating
 Min --------------------------------------- 7.33 Lbs
 Max--------------------------------------- 9.48 Lbs
 After thermal aging
o Mating
 Min --------------------------------------- 6.64 Lbs
 Max--------------------------------------- 7.91 Lbs
o Unmating
 Min --------------------------------------- 4.15 Lbs
 Max--------------------------------------- 5.99 Lbs
Page 15 of 54
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
RESULTS Continued
Mating&Unmating durability (LPHS-08-32-L-RT1-GP/0.056” thick card):






Initial
o Mating
 Min --------------------------------------- 6.33 Lbs
 Max--------------------------------------- 8.57 Lbs
o Unmating
 Min --------------------------------------- 4.88 Lbs
 Max--------------------------------------- 6.86 Lbs
After 25 Cycles
o Mating
 Min --------------------------------------- 7.19 Lbs
 Max--------------------------------------- 9.56 Lbs
o Unmating
 Min --------------------------------------- 4.74 Lbs
 Max--------------------------------------- 6.91 Lbs
After 50 Cycles
o Mating
 Min --------------------------------------- 7.92 Lbs
 Max--------------------------------------10.01 Lbs
o Unmating
 Min --------------------------------------- 5.19 Lbs
 Max--------------------------------------- 7.02 Lbs
After 75 Cycles
o Mating
 Min --------------------------------------- 8.13 Lbs
 Max--------------------------------------10.20 Lbs
o Unmating
 Min --------------------------------------- 5.63 Lbs
 Max--------------------------------------- 7.11 Lbs
After 100 Cycles
o Mating
 Min --------------------------------------- 8.31 Lbs
 Max--------------------------------------10.30 Lbs
o Unmating
 Min --------------------------------------- 5.86 Lbs
 Max--------------------------------------- 7.15 Lbs
After Humidity
o Mating
 Min --------------------------------------- 4.39 Lbs
 Max--------------------------------------- 5.12 Lbs
o Unmating
 Min --------------------------------------- 3.38 Lbs
 Max--------------------------------------- 4.03 Lbs
Page 16 of 54
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
RESULTS Continued
Mating&Unmating durability (LPHS-08-32-L-RT1-GP/0.068” thick card):






Initial
o Mating
 Min --------------------------------------- 9.74 Lbs
 Max--------------------------------------11.91 Lbs
o Unmating
 Min --------------------------------------- 5.51 Lbs
 Max--------------------------------------- 6.77 Lbs
After 25 Cycles
o Mating
 Min --------------------------------------11.04 Lbs
 Max--------------------------------------13.13 Lbs
o Unmating
 Min --------------------------------------- 5.56 Lbs
 Max--------------------------------------- 6.78 Lbs
After 50 Cycles
o Mating
 Min --------------------------------------11.80 Lbs
 Max--------------------------------------13.74 Lbs
o Unmating
 Min --------------------------------------- 6.12 Lbs
 Max--------------------------------------- 7.37 Lbs
After 75 Cycles
o Mating
 Min --------------------------------------12.04 Lbs
 Max--------------------------------------14.72 Lbs
o Unmating
 Min --------------------------------------- 6.43 Lbs
 Max--------------------------------------- 7.89 Lbs
After 100 Cycles
o Mating
 Min --------------------------------------12.29 Lbs
 Max--------------------------------------15.55 Lbs
o Unmating
 Min --------------------------------------- 6.83 Lbs
 Max--------------------------------------- 8.33 Lbs
After Humidity
o Mating
 Min --------------------------------------- 6.59 Lbs
 Max--------------------------------------- 8.25 Lbs
o Unmating
 Min --------------------------------------- 4.91 Lbs
 Max--------------------------------------- 7.83 Lbs
Page 17 of 54
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
RESULTS Continued
Mating&Unmating basic (LPHS-06-24-L-RT1-GP/0.068” thick card)





Initial
o Mating
 Min --------------------------------------- 9.47 Lbs
 Max--------------------------------------12.06 Lbs
o Unmating
 Min --------------------------------------- 5.61 Lbs
 Max--------------------------------------- 7.32 Lbs
After 25 Cycles
o Mating
 Min --------------------------------------- 9.61 Lbs
 Max--------------------------------------13.74 Lbs
o Unmating
 Min --------------------------------------- 5.38 Lbs
 Max--------------------------------------- 8.08 Lbs
After 50 Cycles
o Mating
 Min --------------------------------------- 9.88 Lbs
 Max--------------------------------------13.02 Lbs
o Unmating
 Min --------------------------------------- 5.75 Lbs
 Max--------------------------------------- 8.67 Lbs
After 75 Cycles
o Mating
 Min --------------------------------------10.39 Lbs
 Max--------------------------------------13.11 Lbs
o Unmating
 Min --------------------------------------- 6.20 Lbs
 Max--------------------------------------- 9.57 Lbs
After 100 Cycles
o Mating
 Min --------------------------------------10.67 Lbs
 Max--------------------------------------13.21 Lbs
o Unmating
 Min --------------------------------------- 6.54 Lbs
 Max--------------------------------------- 9.62 Lbs
Page 18 of 54
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
RESULTS Continued
Mating&Unmating basic (LPHS-04-20-L-RT1-GP/0.068”thick card)





Initial
o Mating
 Min --------------------------------------- 7.29 Lbs
 Max--------------------------------------- 9.86 Lbs
o Unmating
 Min --------------------------------------- 4.09 Lbs
 Max--------------------------------------- 5.89 Lbs
After 25 Cycles
o Mating
 Min --------------------------------------- 7.11 Lbs
 Max--------------------------------------10.50 Lbs
o Unmating
 Min --------------------------------------- 3.80 Lbs
 Max--------------------------------------- 5.95 Lbs
After 50 Cycles
o Mating
 Min --------------------------------------- 7.67 Lbs
 Max--------------------------------------10.79 Lbs
o Unmating
 Min --------------------------------------- 4.06 Lbs
 Max--------------------------------------- 6.56 Lbs
After 75 Cycles
o Mating
 Min --------------------------------------- 7.83 Lbs
 Max--------------------------------------10.59 Lbs
o Unmating
 Min --------------------------------------- 4.13 Lbs
 Max--------------------------------------- 7.01 Lbs
After 100 Cycles
o Mating
 Min --------------------------------------- 7.83 Lbs
 Max--------------------------------------10.05 Lbs
o Unmating
 Min --------------------------------------- 4.41 Lbs
 Max--------------------------------------- 7.32 Lbs
Page 19 of 54
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
RESULTS Continued
Normal force
Signal pin(C-378-01) at 0.016 inch deflection
o Initial
 Min ------------------------------------ 105.60 gf
 Max------------------------------------ 122.20 gf
o After thermal
 Min --------------------------------------86.30 gf
 Max------------------------------------ 110.00 gf
Power pin(C-377-01) at 0.016 inch deflection
o Initial
 Min ------------------------------------ 701.50 gf
 Max------------------------------------ 784.40 gf
o After thermal
 Min ------------------------------------ 401.50 gf
 Max------------------------------------ 557.70 gf
Power pin(C-377-02) at 0.0175 inch deflection
o Initial
 Min ------------------------------------ 716.70 gf
 Max------------------------------------ 751.90 gf
o After thermal
 Min ------------------------------------ 411.80 gf
 Max------------------------------------ 539.00 gf
Set-----0.0001 inch
Set-----0.0016 inch
Set-----0.0002 inch
Set-----0.0020 inch
Set-----0.0004 inch
Set-----0.0021 inch
Set-----0.0055 inch
Set-----0.0092 inch
Set-----0.0000 inch
Set-----0.0010 inch
Set-----0.0055 inch
Set-----0.0081 inch
LLCR Durability-0.056” thick edge card (160 signal pin and 32 power pin LLCR test points)
Signal pin:
 Initial --------------------------------------------------------------- 23.23 mOhms Max
Power pin:
 Initial ----------------------------------------------------------------- 0.30 mOhms Max
 After 100 Cycles
o <= +5.0 mOhms ----------------------------------- 192 Points ------------------------- Stable
o +5.1 to +10.0 mOhms ----------------------------------- 0 Points ------------------------- Minor
o +10.1 to +15.0 mOhms --------------------------------- 0 Points ------------------------- Acceptable
o +15.1 to +50.0 mOhms --------------------------------- 0 Points ------------------------- Marginal
o +50.1 to +2000 mOhms --------------------------------- 0 Points ------------------------- Unstable
o >+2000 mOhms ------------------------------------------ 0 Points ------------------------- Open Failure
 After thermal shock
o <= +5.0 mOhms ----------------------------------- 191 Points ------------------------- Stable
o +5.1 to +10.0 mOhms ----------------------------------- 1 Points ------------------------- Minor
o +10.1 to +15.0 mOhms --------------------------------- 0 Points ------------------------- Acceptable
o +15.1 to +50.0 mOhms --------------------------------- 0 Points ------------------------- Marginal
o +50.1 to +2000 mOhms --------------------------------- 0 Points ------------------------- Unstable
o >+2000 mOhms ------------------------------------------ 0 Points ------------------------- Open Failure
 After humidity
o <= +5.0 mOhms ----------------------------------- 188 Points ------------------------- Stable
o +5.1 to +10.0 mOhms ----------------------------------- 4 Points ------------------------- Minor
o +10.1 to +15.0 mOhms --------------------------------- 0 Points ------------------------- Acceptable
o +15.1 to +50.0 mOhms --------------------------------- 0 Points ------------------------- Marginal
o +50.1 to +2000 mOhms --------------------------------- 0 Points ------------------------- Unstable
o >+2000 mOhms ------------------------------------------ 0 Points ------------------------- Open Failure
o >+2000 mOhms ------------------------------------------ 0 Points ------------------------- Open Failure
Page 20 of 54
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
RESULTS Continued
LLCR Durability-0.068” thick edge card (160 signal pin and 32 power pin LLCR test points)
Signal pin:
 Initial --------------------------------------------------------------- 23.00 mOhms Max
Power pin:
 Initial ----------------------------------------------------------------- 0.30 mOhms Max
 After 100 Cycles
o <= +5.0 mOhms ----------------------------------- 192 Points ------------------------- Stable
o +5.1 to +10.0 mOhms ----------------------------------- 0 Points ------------------------- Minor
o +10.1 to +15.0 mOhms --------------------------------- 0 Points ------------------------- Acceptable
o +15.1 to +50.0 mOhms --------------------------------- 0 Points ------------------------- Marginal
o +50.1 to +2000 mOhms --------------------------------- 0 Points ------------------------- Unstable
o >+2000 mOhms ------------------------------------------ 0 Points ------------------------- Open Failure
 After thermal shock
o <= +5.0 mOhms ----------------------------------- 192 Points ------------------------- Stable
o +5.1 to +10.0 mOhms ----------------------------------- 0 Points ------------------------- Minor
o +10.1 to +15.0 mOhms --------------------------------- 0 Points ------------------------- Acceptable
o +15.1 to +50.0 mOhms --------------------------------- 0 Points ------------------------- Marginal
o +50.1 to +2000 mOhms --------------------------------- 0 Points ------------------------- Unstable
o >+2000 mOhms ------------------------------------------ 0 Points ------------------------- Open Failure
 After humidity
o <= +5.0 mOhms ----------------------------------- 187 Points ------------------------- Stable
o +5.1 to +10.0 mOhms ----------------------------------- 5 Points ------------------------- Minor
o +10.1 to +15.0 mOhms --------------------------------- 0 Points ------------------------- Acceptable
o +15.1 to +50.0 mOhms --------------------------------- 0 Points ------------------------- Marginal
o +50.1 to +2000 mOhms --------------------------------- 0 Points ------------------------- Unstable
o >+2000 mOhms ------------------------------------------ 0 Points ------------------------- Open Failure
o >+2000 mOhms ------------------------------------------ 0 Points ------------------------- Open Failure
LLCR Thermal Aging -0.056” thick edge card (160 signal pin and 32 power pin LLCR test points)
Signal Pin:
 Initial --------------------------------------------------------------- 23.11 mOhms Max
Power Pin:
 Initial ----------------------------------------------------------------- 0.34 mOhms Max
 Thermal Aging
o <= +5.0 mOhms ----------------------------------- 170 Points ------------------------- Stable
o +5.1 to +10.0 mOhms --------------------------------- 22 Points ------------------------- Minor
o +10.1 to +15.0 mOhms --------------------------------- 0 Points ------------------------- Acceptable
o +15.1 to +50.0 mOhms --------------------------------- 0 Points ------------------------- Marginal
o +50.1 to +2000 mOhms --------------------------------- 0 Points ------------------------- Unstable
o >+2000 mOhms ------------------------------------------ 0 Points ------------------------- Open Failure
LLCR Thermal Aging -0.068” thick edge card (160 signal pin and 32 power pin LLCR test points)
Signal Pin:
 Initial --------------------------------------------------------------- 22.72 mOhms Max
Power Pin:
 Initial ----------------------------------------------------------------- 0.28 mOhms Max
 Thermal Aging
o <= +5.0 mOhms ----------------------------------- 191 Points ------------------------- Stable
o +5.1 to +10.0 mOhms ----------------------------------- 1 Points ------------------------- Minor
o +10.1 to +15.0 mOhms --------------------------------- 0 Points ------------------------- Acceptable
o +15.1 to +50.0 mOhms --------------------------------- 0 Points ------------------------- Marginal
o +50.1 to +2000 mOhms --------------------------------- 0 Points ------------------------- Unstable
o >+2000 mOhms ------------------------------------------ 0 Points ------------------------- Open Failure
Page 21 of 54
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
RESULTS Continued
LLCR Gas Tight (160 signal pin and 32 power pin LLCR test points)
Signal Pin:
 Initial --------------------------------------------------------------- 22.70 mOhms Max
Power Pin:
 Initial ----------------------------------------------------------------- 0.33 mOhms Max
 Gas-Tight
o <= +5.0 mOhms ----------------------------------- 192 Points ------------------------- Stable
o +5.1 to +10.0 mOhms ----------------------------------- 0 Points ------------------------- Minor
o +10.1 to +15.0 mOhms --------------------------------- 0 Points ------------------------- Acceptable
o +15.1 to +50.0 mOhms --------------------------------- 0 Points ------------------------- Marginal
o +50.1 to +2000 mOhms --------------------------------- 0 Points ------------------------- Unstable
o >+2000 mOhms ------------------------------------------ 0 Points ------------------------- Open Failure
LLCR Shock Vib-0.056” thick edge card (160 signal pin and 32 power pin LLCR test points)
Signal Pin:
 Initial --------------------------------------------------------------- 23.38 mOhms Max
Power Pin:
 Initial ----------------------------------------------------------------- 0.32 mOhms Max
 S&V
o <= +5.0 mOhms ----------------------------------- 192 Points ------------------------- Stable
o +5.1 to +10.0 mOhms ----------------------------------- 0 Points ------------------------- Minor
o +10.1 to +15.0 mOhms --------------------------------- 0 Points ------------------------- Acceptable
o +15.1 to +50.0 mOhms --------------------------------- 0 Points ------------------------- Marginal
o +50.1 to +2000 mOhms --------------------------------- 0 Points ------------------------- Unstable
o >+2000 mOhms ------------------------------------------ 0 Points ------------------------- Open Failure
LLCR Shock Vib-0.068” thick edge card (160 signal pin and 32 power pin LLCR test points)
Signal Pin:
 Initial --------------------------------------------------------------- 23.35 mOhms Max
Power Pin:
 Initial ----------------------------------------------------------------- 0.28 mOhms Max
 S&V
o <= +5.0 mOhms ----------------------------------- 192 Points ------------------------- Stable
o +5.1 to +10.0 mOhms ----------------------------------- 0 Points ------------------------- Minor
o +10.1 to +15.0 mOhms --------------------------------- 0 Points ------------------------- Acceptable
o +15.1 to +50.0 mOhms --------------------------------- 0 Points ------------------------- Marginal
o +50.1 to +2000 mOhms --------------------------------- 0 Points ------------------------- Unstable
o >+2000 mOhms ------------------------------------------ 0 Points ------------------------- Open Failure
Mechanical Shock & Random Vibration:
o
o
Shock
 No Damage ----------------------------------- ---------------------------------- Passed
 50 Nanoseconds ------------------------------ ---------------------------------- Passed
Vibration
 No Damage ----------------------------------- ---------------------------------- Passed
 50 Nanoseconds ------------------------------ ---------------------------------- Passed
Page 22 of 54
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
RESULTS Continued
Insulation Resistance minimums, IR
Signal Pin- Siganl Pin
 Initial
o Mated ------------------------------------------------ 10000Meg Ω ------------------------- Pass
o Unmated -------------------------------------------- 10000Meg Ω ------------------------ Pass
 Thermal
o Mated ------------------------------------------------ 10000Meg Ω ------------------------ Pass
o Unmated -------------------------------------------- 10000Meg Ω ------------------------ Pass
 Humidity
o Mated ------------------------------------------------ 10000Meg Ω ------------------------ Pass
o Unmated --------------------------------------------- 9000Meg Ω ------------------------ Pass
Signal Row- Siganl Row
 Initial
o Mated ------------------------------------------------ 10000Meg Ω ------------------------- Pass
o Unmated -------------------------------------------- 10000Meg Ω ------------------------ Pass
 Thermal
o Mated ------------------------------------------------ 10000Meg Ω ------------------------ Pass
o Unmated -------------------------------------------- 10000Meg Ω ------------------------ Pass
 Humidity
o Mated ------------------------------------------------ 10000Meg Ω ------------------------ Pass
o Unmated -------------------------------------------- 10000Meg Ω ------------------------ Pass
Siganl Pin-Power pin
 Initial
o Mated ------------------------------------------------ 10000Meg Ω ------------------------- Pass
o Unmated -------------------------------------------- 10000Meg Ω ------------------------ Pass
 Thermal
o Mated ------------------------------------------------ 10000Meg Ω ------------------------ Pass
o Unmated -------------------------------------------- 10000Meg Ω ------------------------ Pass
 Humidity
o Mated ------------------------------------------------ 10000Meg Ω ------------------------ Pass
o Unmated -------------------------------------------- 10000Meg Ω ------------------------ Pass
Power pin-Power pin
 Initial
o Mated ------------------------------------------------ 10000Meg Ω ------------------------- Pass
o Unmated -------------------------------------------- 10000Meg Ω ------------------------ Pass
 Thermal
o Mated ------------------------------------------------ 10000Meg Ω ------------------------ Pass
o Unmated -------------------------------------------- 10000Meg Ω ------------------------ Pass
 Humidity
o Mated ------------------------------------------------ 10000Meg Ω ------------------------ Pass
o Unmated -------------------------------------------- 10000Meg Ω ------------------------ Pass
Page 23 of 54
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
RESULTS Continued
Dielectric Withstanding Voltage minimums, DWV
Signal pin
 Minimums
o Breakdown Voltage ---------------------------------- 875VAC
o Test Voltage ------------------------------------------- 656VAC
o Working Voltage ------------------------------------- 219VAC
Power pin
 Minimums
o Breakdown Voltage -------------------------------- 1500VAC
o Test Voltage ----------------------------------------- 1125VAC
o Working Voltage ------------------------------------- 375VAC
Signal Pin- Siganl Pin
 Initial DWV -------------------------------------------------- Passed
 Thermal DWV ----------------------------------------------- Passed
 Humidity DWV---------------------------------------------- Passed
Signal Row- Siganl Row
 Initial DWV -------------------------------------------------- Passed
 Thermal DWV ----------------------------------------------- Passed
 Humidity DWV---------------------------------------------- Passed
Signal Pin - Power
 Initial DWV -------------------------------------------------- Passed
 Thermal DWV ----------------------------------------------- Passed
 Humidity DWV---------------------------------------------- Passed
Power pin-Power pin
 Initial DWV -------------------------------------------------- Passed
 Thermal DWV ----------------------------------------------- Passed
 Humidity DWV---------------------------------------------- Passed
Page 24 of 54
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
DATA SUMMARIES
TEMPERATURE RISE (Current Carrying Capacity, CCC):
1) High quality thermocouples whose temperature slopes track one another were used for temperature
monitoring.
2) The thermocouples were placed at a location to sense the maximum temperature generated during testing.
3) Temperature readings recorded are those for which three successive readings, 15 minutes apart, differ less
than 1° C (computer controlled data acquisition).
4) Adjacent contacts were powered:
Signal pin:
a. Linear configuration with 2 adjacent signal conductors/contacts powered
261999
2 (2x1) Signal Pins Powered in Series
Part Numbers: LPHS-08-32-L-RT1-GP/Edge Card (.056")
Current Rating per Contact (30 Deg. Rise, 20% Derated) = 2.4 Amps
7.0
Room Temp= 21.6°C
6.0
Maximum Current, Amps per Contact
5.2
5.0
105°C
Limit
4.0
3.6
4.2
3.1
3.0
2.8
2.4
2.0
1.7
1.4
1.0
0.0
20
30
40
50
60
70
80
90
100
110
Ambient Temperature (°C)
Base Curve
Derated 20 %
Measured Current
RT Peak Amp
RT Derated Amp
65°C Peak Amp
65°C Derated Amp
75°C Peak Amp
75°C Derated Amp
95°C Peak Amp
95°C Derated Amp
Limit
261999
2 (2x1) Signal Pins Powered in Series
Part Numbers: LPHS-08-32-L-RT1-GP/Edge Card (.056")
50
45
Temperature Rise (°C above ambient)
40
35
30
25
20
15
10
5
0
0
0.5
1
1.5
2
Current (Amps)
Actual
20% Derated
Page 25 of 54
2.5
3
3.5
4
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
DATA SUMMARIES
b. Linear configuration with 4 adjacent signal conductors/contacts powered
261999
4 (2x2) Signal Pins Powered in Series
Part Numbers: LPHS-08-32-L-RT1-GP/Edge Card (.056")
Current Rating per Contact (30 Deg. Rise, 20% Derated) = 1.9 Amps
5.0
Room Temp= 21.5°C
4.5
Maximum Current, Amps per Contact
4.0
3.9
3.5
3.0
105°C
Limit
2.7
3.1
2.3
2.5
2.0
2.1
1.9
1.5
1.3
1.0
1.1
0.5
0.0
20
30
40
50
60
70
80
90
100
110
Ambient Temperature (°C)
Base Curve
Derated 20 %
Measured Current
RT Peak Amp
RT Derated Amp
65°C Peak Amp
65°C Derated Amp
75°C Peak Amp
75°C Derated Amp
95°C Peak Amp
95°C Derated Amp
Limit
261999
4 (2x2) Signal Pins Powered in Series
Part Numbers: LPHS-08-32-L-RT1-GP/Edge Card (.056")
60
Temperature Rise (°C above ambient)
50
40
30
20
10
0
0
0.5
1
1.5
2
Current (Amps)
Actual
20% Derated
Page 26 of 54
2.5
3
3.5
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
DATA SUMMARIES
c. Linear configuration with 6 adjacent signal conductors/contacts powered
261999
6 (2x3) Signal Pins Powered in Series
Part Numbers: LPHS-08-32-L-RT1-GP/Edge Card (.056")
Current Rating per Contact (30 Deg. Rise, 20% Derated) = 1.8 Amps
5.0
Room Temp= 21.7°C
4.5
Maximum Current, Amps per Contact
4.0
3.7
3.5
3.0
105°C
Limit
2.6
3.0
2.5
2.2
2.0
2.0
1.8
1.5
1.2
1.0
1.0
0.5
0.0
20
30
40
50
60
70
Ambient Temperature (°C)
80
90
100
Base Curve
Derated 20 %
Measured Current
RT Peak Amp
RT Derated Amp
65°C Peak Amp
65°C Derated Amp
75°C Peak Amp
75°C Derated Amp
95°C Peak Amp
95°C Derated Amp
Limit
110
261999
6 (2x3) Signal Pins Powered in Series
Part Numbers: LPHS-08-32-L-RT1-GP/Edge Card (.056")
50
45
Temperature Rise (°C above ambient)
40
35
30
25
20
15
10
5
0
0
0.5
1
1.5
Current (Amps)
Actual
20% Derated
Page 27 of 54
2
2.5
3
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
DATA SUMMARIES
d. Linear configuration with 8 adjacent signal conductors/contacts powered
261999
8 (2x4) Signal Pins Powered in Series
Part Numbers: LPHS-08-32-L-RT1-GP/Edge Card (.056")
Current Rating per Contact (30 Deg. Rise, 20% Derated) = 1.4 Amps
4.0
Room Temp= 22.1°C
3.5
3.0
Maximum Current, Amps per Contact
3.0
2.5
105°C
Limit
2.1
2.4
2.0
1.8
1.5
1.7
1.4
1.0
1.0
0.8
0.5
0.0
20
30
40
50
60
70
Ambient Temperature (°C)
80
90
100
Base Curve
Derated 20 %
Measured Current
RT Peak Amp
RT Derated Amp
65°C Peak Amp
65°C Derated Amp
75°C Peak Amp
75°C Derated Amp
95°C Peak Amp
95°C Derated Amp
Limit
110
261999
8 (2x4) Signal Pins Powered in Series
Part Numbers: LPHS-08-32-L-RT1-GP/Edge Card (.056")
60
Temperature Rise (°C above ambient)
50
40
30
20
10
0
0
0.5
1
1.5
Current (Amps)
Actual
20% Derated
Page 28 of 54
2
2.5
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
DATA SUMMARIES
e. Linear configuration with All adjacent signal conductors/contacts powered
261999
32 (All Power) Signal Pins Powered in Series
Part Numbers: LPHS-08-32-L-RT1-GP/Edge Card (.056")
Current Rating per Contact (30 Deg. Rise, 20% Derated) = 1.0 Amps
2.5
Room Temp= 22.2°C
2.0
Maximum Current, Amps per Contact
2.0
1.6
1.5
105°C
Limit
1.4
1.2
1.0
1.1
1.0
0.7
0.5
0.5
0.0
20
30
40
50
60
70
80
90
100
110
Ambient Temperature (°C)
Base Curve
Derated 20 %
Measured Current
RT Peak Amp
RT Derated Amp
65°C Peak Amp
65°C Derated Amp
75°C Peak Amp
75°C Derated Amp
95°C Peak Amp
95°C Derated Amp
Limit
261999
32 (All Power) Signal Pins Powered in Series
Part Numbers: LPHS-08-32-L-RT1-GP/Edge Card (.056")
60
Temperature Rise (°C above ambient)
50
40
30
20
10
0
0
0.2
0.4
0.6
0.8
1
Current (Amps)
Actual
20% Derated
Page 29 of 54
1.2
1.4
1.6
1.8
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
DATA SUMMARIES
Power pin:
f.
Linear configuration with 2 adjacent power conductors/contacts powered
261999
2 (2x1) Power Pins Powered in Series
Part Numbers: LPHS-08-32-L-RT1-GP/Edge Card (.056")
Current Rating per Contact (30 Deg. Rise, 20% Derated) = 29.2 Amps
80.0
Room Temp= 20.8°C
70.0
62.4
Maximum Current, Amps per Contact
60.0
50.0
49.9
105°C
Limit
42.4
36.5
40.0
34.0
30.0
29.2
20.5
20.0
16.4
10.0
0.0
20
30
40
50
60
70
80
90
100
110
Ambient Temperature (°C)
Base Curve
Derated 20 %
Measured Current
RT Peak Amp
RT Derated Amp
65°C Peak Amp
65°C Derated Amp
75°C Peak Amp
75°C Derated Amp
95°C Peak Amp
95°C Derated Amp
Limit
261999
2 (2x1) Power Pins Powered in Series
Part Numbers: LPHS-08-32-L-RT1-GP/Edge Card (.056")
Temperature Rise (°C above ambient)
50
40
30
20
10
0
0
10
20
30
Current (Amps)
Actual
20% Derated
Page 30 of 54
40
50
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
DATA SUMMARIES
g. Linear configuration with 4 adjacent power conductors/contacts powered
261999
4 (2x2) Power Pins Powered in Series
Part Numbers: LPHS-08-32-L-RT1-GP/Edge Card (.056")
Current Rating per Contact (30 Deg. Rise, 20% Derated) = 24.9 Amps
Room Temp= 20.1°C
60.0
52.3
Maximum Current, Amps per Contact
50.0
40.0
105°C
Limit
36.0
41.8
31.1
30.0
28.8
24.9
17.7
20.0
14.2
10.0
0.0
20
30
40
50
60
70
Ambient Temperature (°C)
80
90
100
110
Base Curve
Derated 20 %
Measured Current
RT Peak Amp
RT Derated Amp
65°C Peak Amp
65°C Derated Amp
75°C Peak Amp
75°C Derated Amp
95°C Peak Amp
95°C Derated Amp
Limit
40
45
261999
4 (2x2) Power Pins Powered in Series
Part Numbers: LPHS-08-32-L-RT1-GP/Edge Card (.056")
60
Temperature Rise (°C above ambient)
50
40
30
20
10
0
0
5
10
15
20
25
Current (Amps)
Actual
20% Derated
Page 31 of 54
30
35
50
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
DATA SUMMARIES
h. Linear configuration with 6 adjacent power conductors/contacts powered
261999
6 (2x3) Power Pins Powered in Series
Part Numbers: LPHS-08-32-L-RT1-GP/Edge Card (.056")
Current Rating per Contact (30 Deg. Rise, 20% Derated) = 22.0 Amps
60.0
Room Temp= 21.1°C
Maximum Current, Amps per Contact
50.0
47.1
40.0
105°C
Limit
37.7
32.0
27.5
30.0
25.6
20.0
22.0
15.1
10.0
12.1
0.0
20
30
40
50
60
70
80
90
100
110
Ambient Temperature (°C)
Base Curve
Derated 20 %
Measured Current
RT Peak Amp
RT Derated Amp
65°C Peak Amp
65°C Derated Amp
75°C Peak Amp
75°C Derated Amp
95°C Peak Amp
95°C Derated Amp
Limit
261999
6 (2x3) Power Pins Powered in Series
Part Numbers: LPHS-08-32-L-RT1-GP/Edge Card (.056")
70
Temperature Rise (°C above ambient)
60
50
40
30
20
10
0
0
5
10
15
20
25
Current (Amps)
Actual
20% Derated
Page 32 of 54
30
35
40
45
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
DATA SUMMARIES
i.
Linear configuration with All adjacent power conductors/contacts powered
261999
8 (All Power) Power Pins Powered in Series
Part Numbers: LPHS-08-32-L-RT1-GP/Edge Card (.056")
Current Rating per Contact (30 Deg. Rise, 20% Derated) = 20.8 Amps
Room Temp= 21.8°C
50.0
Maximum Current, Amps per Contact
44.0
40.0
35.2
105°C
Limit
30.2
30.0
26.0
24.1
20.0
20.8
14.7
10.0
11.7
0.0
20
30
40
50
60
70
80
90
100
110
Ambient Temperature (°C)
Base Curve
Derated 20 %
Measured Current
RT Peak Amp
RT Derated Amp
65°C Peak Amp
65°C Derated Amp
75°C Peak Amp
75°C Derated Amp
95°C Peak Amp
95°C Derated Amp
Limit
261999
8 (All Power) Power Pins Powered in Series
Part Numbers: LPHS-08-32-L-RT1-GP/Edge Card (.056")
80
Temperature Rise (°C above ambient)
70
60
50
40
30
20
10
0
0
5
10
15
20
Current (Amps)
Actual
20% Derated
Page 33 of 54
25
30
35
40
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
DATA SUMMARIES
Power Pin powered while signal pin @ 1/2 rated current at 0.6 Amps
j. All Power Pins (while signal pin at 0.6 Amps) Contacts Powered
261999
8 (All Power) Power Pins Powered in Series (Signal Pins Powered at 1/2 rated current - 0.6 amps)
Part Numbers: LPHS-08-32-L-RT1-GP/Edge Card (.056")
Current Rating per Contact (30 Deg. Rise, 20% Derated) = 21.2 Amps
60.0
Room Temp= 21.1°C
Maximum Current, Amps per Contact
50.0
45.7
40.0
36.6
105°C
Limit
30.9
30.0
26.5
24.8
20.0
21.2
14.6
10.0
11.7
0.0
20
30
40
50
60
70
80
90
100
110
Ambient Temperature (°C)
Base Curve
Derated 20 %
Measured Current
RT Peak Amp
RT Derated Amp
65°C Peak Amp
65°C Derated Amp
75°C Peak Amp
75°C Derated Amp
95°C Peak Amp
95°C Derated Amp
Limit
261999
8 (All Power) Power Pins Powered in Series (Signal Pins Poweref @ 1/2 rated current - 0.6 amps)
Part Numbers: LPHS-08-32-L-RT1-GP/Edge Card (.056")
60
Temperature Rise (°C above ambient)
50
40
30
20
10
0
0
5
10
15
20
Current (Amps)
Actual
20% Derated
Page 34 of 54
25
30
35
40
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
DATA SUMMARIES
MATING/UNMATING FORCE:
Mating/Unmating durability (LPHS-08-32-L-RT1-GP/0.056” thick card):
Initial
After 25 Cycles
Mating
Unmating
Mating
Unmating
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Minimum
28.16
6.33
21.71
4.88
31.98
7.19
21.08
4.74
Maximum
38.12
8.57
30.51
6.86
42.52
9.56
30.74
6.91
Average
34.46
7.75
25.95
5.83
37.76
8.49
26.65
5.99
St Dev
3.47
0.78
2.61
0.59
3.52
0.79
2.74
0.62
Count
8
8
8
8
8
8
8
8
After 50 Cycles
Mating
After 75 Cycles
Unmating
Mating
Unmating
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Minimum
35.23
7.92
23.09
5.19
36.16
8.13
25.04
5.63
Maximum
44.52
10.01
31.22
7.02
45.37
10.20
31.63
7.11
Average
39.93
8.98
27.69
6.23
41.41
9.31
28.97
6.51
St Dev
3.34
0.75
2.36
0.53
3.30
0.74
2.01
0.45
Count
8
8
8
8
8
8
8
8
After 100 Cycles
Mating
Newtons
After Humidity
Unmating
Force (Lbs)
Newtons
Mating
Force (Lbs)
Newtons
Unmating
Force (Lbs)
Newtons
Force (Lbs)
Minimum
36.96
8.31
26.07
5.86
19.53
4.39
15.03
3.38
Maximum
45.81
10.30
31.80
7.15
22.77
5.12
17.93
4.03
Average
42.95
9.66
29.92
6.73
21.49
4.83
16.41
3.69
St Dev
3.05
0.68
1.78
0.40
1.23
0.28
1.11
0.25
Count
8
8
8
8
8
8
8
8
Page 35 of 54
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
DATA SUMMARIES Continued
Mating/Unmating durability (LPHS-08-32-L-RT1-GP/0.068” thick card):
Initial
After 25 Cycles
Mating
Unmating
Mating
Unmating
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Minimum
43.32
9.74
24.51
5.51
49.11
11.04
24.73
5.56
Maximum
52.98
11.91
30.11
6.77
58.40
13.13
30.16
6.78
Average
47.98
10.79
27.32
6.14
53.83
12.10
27.61
6.21
St Dev
3.15
0.71
1.99
0.45
3.45
0.78
1.70
0.38
Count
8
8
8
8
8
8
8
8
After 50 Cycles
Mating
After 75 Cycles
Unmating
Mating
Unmating
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Minimum
52.49
11.80
27.22
6.12
53.55
12.04
28.60
6.43
Maximum
61.12
13.74
32.78
7.37
65.47
14.72
35.09
7.89
Average
56.23
12.64
29.71
6.68
58.85
13.23
31.50
7.08
St Dev
3.00
0.67
1.94
0.44
4.12
0.93
2.54
0.57
Count
8
8
8
8
8
8
8
8
After 100 Cycles
Mating
After Humidity
Unmating
Mating
Unmating
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Minimum
54.67
12.29
30.38
6.83
29.31
6.59
21.84
4.91
Maximum
69.17
15.55
37.05
8.33
36.70
8.25
34.83
7.83
Average
61.14
13.75
33.39
7.51
31.90
7.17
26.15
5.88
St Dev
4.55
1.02
2.45
0.55
2.38
0.53
4.31
0.97
Count
8
8
8
8
8
8
8
8
Page 36 of 54
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
DATA SUMMARIES Continued
Mating/Unmating basic (LPHS-06-24-L-RT1-GP/0.068” thick card)
Initial
After 25 Cycles
Mating
Unmating
Mating
Unmating
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Minimum
42.12
9.47
24.95
5.61
42.75
9.61
23.93
5.38
Maximum
53.64
12.06
32.56
7.32
61.12
13.74
35.94
8.08
Average
46.40
10.43
28.57
6.42
50.76
11.41
30.55
6.87
St Dev
3.62
0.81
3.49
0.79
5.69
1.28
3.88
0.87
Count
8
8
8
8
8
8
8
8
After 50 Cycles
Mating
After 75 Cycles
Unmating
Mating
Unmating
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Minimum
43.95
9.88
25.58
5.75
46.21
10.39
27.58
6.20
Maximum
57.91
13.02
38.56
8.67
58.31
13.11
42.57
9.57
Average
52.02
11.70
32.50
7.31
52.98
11.91
34.22
7.69
St Dev
4.19
0.94
3.89
0.87
3.83
0.86
4.43
1.00
Count
8
8
8
8
8
8
8
8
After 100 Cycles
Mating
Unmating
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Minimum
47.46
10.67
29.09
6.54
Maximum
58.76
13.21
42.79
9.62
Average
53.21
11.96
36.17
8.13
St Dev
3.65
0.82
4.16
0.94
Count
8
8
8
8
Page 37 of 54
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
DATA SUMMARIES Continued
Mating/Unmating basic (LPHS-04-20-L-RT1-GP/0.068” thick card)
Initial
After 25 Cycles
Mating
Unmating
Mating
Unmating
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Minimum
32.43
7.29
18.19
4.09
31.63
7.11
16.90
3.80
Maximum
43.86
9.86
26.20
5.89
46.70
10.50
26.47
5.95
Average
35.85
8.06
22.91
5.15
38.07
8.56
23.40
5.26
St Dev
3.64
0.82
2.50
0.56
4.41
0.99
3.25
0.73
Count
8
8
8
8
8
8
8
8
After 50 Cycles
Mating
After 75 Cycles
Unmating
Mating
Unmating
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Minimum
34.12
7.67
18.06
4.06
34.83
7.83
18.37
4.13
Maximum
47.99
10.79
29.18
6.56
47.10
10.59
31.18
7.01
Average
39.24
8.82
25.43
5.72
39.65
8.92
27.22
6.12
St Dev
4.41
0.99
3.77
0.85
4.12
0.93
4.00
0.90
Count
8
8
8
8
8
8
8
8
After 100 Cycles
Mating
Newtons
Unmating
Force (Lbs)
Newtons
Force (Lbs)
Minimum
34.83
7.83
19.62
4.41
Maximum
44.70
10.05
32.56
7.32
Average
40.25
9.05
28.82
6.48
St Dev
3.77
0.85
4.21
0.95
Count
8
8
8
8
Page 38 of 54
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
DATA SUMMARIES Continued
Mating/Unmating Data for 20, 24 and 32 signal Position LPHS/Edge card
Mating (Initial)
Unmating (Initial)
Mating (100 Cycles)
Unmating (100 Cycles)
16.00
14.00
12.00
Force (lbs)
10.00
8.00
6.00
4.00
2.00
0.00
20 Pos.
24 Pos.
Number of Terminals per Row
Page 39 of 54
32 Pos.
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
DATA SUMMARIES Continued
Thermal aging (LPHS-08-32-L-RT1-GP/0.056” thick card)
Initial
After Thermals
Mating
Unmating
Mating
Unmating
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Minimum
33.58
7.55
27.76
6.24
18.55
4.17
14.23
3.20
Maximum
41.14
9.25
31.80
7.15
25.62
5.76
17.93
4.03
Average
38.02
8.55
30.09
6.76
21.97
4.94
16.77
3.77
St Dev
2.58
0.58
1.64
0.37
2.09
0.47
1.15
0.26
Count
8
8
8
8
8
8
8
8
Thermal aging (LPHS-08-32-L-RT1-GP/0.068” thick card)
Initial
After Thermals
Mating
Unmating
Mating
Unmating
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Newtons
Force (Lbs)
Minimum
50.62
11.38
32.60
7.33
29.53
6.64
18.46
4.15
Maximum
61.25
13.77
42.17
9.48
35.18
7.91
26.64
5.99
Average
55.67
12.52
36.37
8.18
31.79
7.15
21.69
4.88
St Dev
3.34
0.75
3.12
0.70
1.64
0.37
3.13
0.70
Count
8
8
8
8
8
8
8
8
Page 40 of 54
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
DATA SUMMARIES Continued
Normal force
Signal pin(C-378-01) at 0.016 inch Deflections
Initial
Deflections in inches Forces in Grams
0.0016 0.0032 0.0048 0.0064 0.0080 0.0096 0.0112 0.0128
29.94
40.91
51.48
61.97
72.60
83.00
93.31
Averages 19.22
5.80
19.30
30.80
41.80
53.50
64.10
74.50
85.20
Min
36.30
46.90
57.50
69.00
79.60
91.20
102.40
Max 27.30
4.890
5.029
5.108
4.883
4.868
5.117
5.396
St. Dev 5.581
12
12
12
12
12
12
12
12
Count
After
Thermals
0.0016
7.44
0.00
20.30
7.160
12
Averages
Min
Max
St. Dev
Count
0.0032
16.83
9.50
30.10
7.227
12
0.0048
25.49
17.50
39.30
7.572
12
0.0144
103.24
95.00
112.60
5.289
12
Deflections in inches Forces in Grams
0.0064 0.0080 0.0096 0.0112
0.0128
34.38
44.37
54.50
65.18
75.80
25.40
34.10
43.40
52.90
63.80
48.30
59.00
68.60
78.20
88.70
7.911
8.452
8.549
8.414
8.268
12
12
12
12
12
0.0144
86.91
75.10
99.30
8.276
12
0.0160
113.19
105.60
122.20
5.110
12
0.0160
97.80
86.30
110.00
8.234
12
SET
0.0002
-0.0001
0.0016
0.0005
12
SET
0.0011
0.0002
0.0020
0.0005
12
Normal Force - Average Initial vs Average Thermal
120
113.2
100
103.2
93.3
Force-Grams
80
83.0
72.6
60
62.0
51.5
40
40.9
97.80
86.91
75.80
65.18
54.50
44.37
34.38
25.49
29.9
20
16.83
19.2
7.44
0
0
0.0
0
0.002
0.004
0.006
0.008
0.01
Deflection-Inches
Page 41 of 54
0.012
0.014
0.016
0.018
Average Initial Normal Force
Average Normal Force after Thermals
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
DATA SUMMARIES Continued
Power pin (C-377-01) at 0.0175 inch Deflections
Initial
Deflections in inches Forces in Grams
0.0018 0.0035 0.0053 0.0070 0.0088 0.0105 0.0123 0.0140
166.55 245.30 328.57 404.18 480.01 551.83 624.38
Averages 81.28
139.40 213.10 289.90 364.40 435.60 506.20 575.20
Min 58.00
Max 115.20 200.90 281.80 370.70 448.30 522.90 593.30 666.90
St. Dev 14.628 17.238 17.798 20.071 21.177 23.500 25.446 28.963
12
12
12
12
12
12
12
12
Count
After
Thermals
Averages
Min
Max
St. Dev
Count
0.0018
0.03
-0.30
0.40
0.218
12
0.0035
0.03
-0.30
0.40
0.239
12
0.0053
0.06
-0.20
0.40
0.207
12
Deflections in inches Forces in Grams
0.0070 0.0088 0.0105 0.0123 0.0140
26.94
96.23
179.00 258.38 341.96
-0.20
0.00
64.70 146.20 228.10
74.10
154.30 238.60 318.00 404.00
28.173 43.149 47.245 45.607 45.485
12
12
12
12
12
0.0158
687.63
640.60
744.30
30.894
12
0.0158
421.68
314.70
486.30
45.078
12
0.0175
734.39
701.50
784.40
24.790
12
0.0175
503.59
401.50
557.70
42.056
12
SET
0.0013
0.0004
0.0021
0.0005
12
SET
0.0067
0.0055
0.0092
0.0010
12
Normal Force - Average Initial vs Average Thermal
800
734.4
700
687.6
600
624.4
503.59
551.8
500
Force-Grams
480.0
421.68
400
404.2
300
341.96
328.6
258.38
245.3
179.00
200
166.6
96.23
100
81.3
0.03
26.94
0.03
0.06
0
0
0.0
0
0.002
0.004
0.006
0.008
0.01
0.012
0.014
0.016
0.018
0.02
-100
Deflection-Inches
Page 42 of 54
Average Initial Normal Force
Average Normal Force after Thermals
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
DATA SUMMARIES Continued
Power pin (C-377-02) at 0.0175 inch Deflections
Initial
Deflections in inches Forces in Grams
0.0018 0.0035 0.0053 0.0070 0.0088 0.0105 0.0123 0.0140
Averages 79.14 164.19 244.60 326.88 401.70 479.67 551.48 625.29
Min 72.10 156.90 232.00 305.60 374.20 450.90 524.20 598.70
Max 92.80 174.10 259.50 343.70 420.30 500.90 576.80 648.20
6.076
8.153 10.513 12.908 14.308 14.938 14.600
St. Dev 5.718
12
12
12
12
12
12
12
12
Count
After
Thermals
Averages
Min
Max
St. Dev
Count
0.0018
0.03
-0.40
0.50
0.281
12
0.0035
0.01
-0.40
0.40
0.268
12
0.0053
0.03
-0.40
0.40
0.273
12
Deflections in inches Forces in Grams
0.0070 0.0088 0.0105 0.0123 0.0140
19.18
90.45
170.43 245.61 323.89
0.00
31.80
111.00 189.60 267.50
71.70
155.70 233.20 309.70 388.70
22.453 33.971 33.859 33.181 33.755
12
12
12
12
12
0.0158
691.33
662.70
711.10
14.326
12
0.0158
397.49
347.50
455.00
31.502
12
0.0175
737.97
716.70
751.90
10.078
12
0.0175
475.42
411.80
539.00
34.984
12
SET
0.0005
0.0000
0.0010
0.0003
12
SET
0.0068
0.0055
0.0081
0.0007
12
Normal Force - Average Initial vs Average Thermal
800
738.0
700
691.3
600
625.3
551.5
500
475.42
Force-Grams
479.7
397.49
400
401.7
323.89
300
326.9
245.61
244.6
200
170.43
164.2
90.45
100
79.1
0.03
0.01
19.18
0
0.03
0
0.0
0
0.002
0.004
0.006
0.008
0.01
0.012
0.014
0.016
0.018
0.02
-100
Deflection-Inches
Page 43 of 54
Average Initial Normal Force
Average Normal Force after Thermals
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
DATA SUMMARIES Continued
INSULATION RESISTANCE (IR):
Signal Pin to Signal Pin
Mated
Unmated
Unmated
LPHS/Card
LPHS
Card
Initial
10000
10000
Not tested
Thermal
10000
10000
Not tested
Humidity
9000
10000
Not tested
Minimum
Signal Row to Signal Row
Mated
Unmated
Unmated
LPHS/ Card
LPHS
Card
Initial
10000
10000
Not tested
Thermal
10000
10000
Not tested
Humidity
10000
10000
Not tested
Minimum
Signal Pin to Power pin
Mated
Unmated
Unmated
LPHS/ Card
LPHS
Card
Initial
10000
10000
Not tested
Thermal
10000
10000
Not tested
Humidity
10000
10000
Not tested
Minimum
Power pin to Power pin
Mated
Unmated
Unmated
LPHS/ Card
LPHS
Card
Initial
10000
10000
Not tested
Thermal
10000
10000
Not tested
Humidity
10000
10000
Not tested
Minimum
Page 44 of 54
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
DATA SUMMARIES Continued
DIELECTRIC WITHSTANDING VOLTAGE (DWV):
Voltage Rating Summary-Signal pin
LPHS/ Card
Minimum
Break Down Voltage
875
Test Voltage
656
Working Voltage
219
Voltage Rating Summary-Power pin
LPHS/ Card
Minimum
Break Down Voltage
1500
Test Voltage
1125
Working Voltage
375
Signal Pin to Signal Pin
Initial Test Voltage
Passed
After Thermal Test Voltage
Passed
After Humidity Test Voltage
Passed
Signal Row to Signal Row
Initial Test Voltage
Passed
After Thermal Test Voltage
Passed
After Humidity Test Voltage
Passed
Signal Pin to Power pin
Initial Test Voltage
Passed
After Thermal Test Voltage
Passed
After Humidity Test Voltage
Passed
Power pin to Power pin
Initial Test Voltage
Passed
After Thermal Test Voltage
Passed
After Humidity Test Voltage
Passed
Page 45 of 54
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
DATA SUMMARIES Continued
LLCR Durabiltiy-0.056” thick card:
1)
2)
3)
4)
A total of 192 points (160 signal pin and 32 power pin LLCR test points) were measured.
EIA-364-23, Low Level Contact Resistance Test Procedure for Electrical Connectors and Sockets.
A computer program, LLCR 221.exe, ensures repeatability for data acquisition.
The following guidelines are used to categorize the changes in LLCR as a result from stressing.
a. <= +5.0 mOhms: --------------------------- Stable
b. +5.1 to +10.0 mOhms: --------------------- Minor
c. +10.1 to +15.0 mOhms: ------------------- Acceptable
d. +15.1 to +50.0 mOhms: ------------------- Marginal
e. +50.1 to +2000 mOhms ------------------- Unstable
f. >+2000 mOhms:---------------------------- Open Failure
LLCR Measurement Summaries by Pin Type
Date
Room Temp (Deg C)
Rel Humidity (%)
5/29/2013
24
60
Peter
Chen
Actual
Initial
6/6/2013
6/18/2013
23
23
58
56
Peter
Chen
Peter Chen
Delta
Delta
100 Cycles
Therm Shck
Pin Type 1: Signal
7/2/2013
23
56
Peter
Chen
Delta
Humidity
Average
St. Dev.
Min
Max
Summary Count
Total Count
18.96
1.86
15.54
23.23
160
160
1.38
1.32
0.00
6.88
160
160
Average
St. Dev.
Min
Max
Summary Count
Total Count
0.26
0.02
0.23
0.30
32
32
0.61
0.85
0.59
0.78
0.00
0.00
3.69
5.62
160
160
160
160
Pin Type 2: Power
0.04
0.06
0.04
0.07
0.00
0.00
0.14
0.36
32
32
32
32
Technician
mOhm values
0.23
0.18
0.02
0.78
32
32
LLCR Delta Count by Category
mOhms
100 Cycles
Therm Shck
Humidity
Stable
<=5
192
191
188
Minor
>5 & <=10
0
1
4
Acceptable
>10 & <=15
0
0
0
Page 46 of 54
Marginal
>15 & <=50
0
0
0
Unstable
>50 & <=1000
0
0
0
Open
>1000
0
0
0
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
DATA SUMMARIES Continued
LLCR Durabiltiy-0.068” thick card:
5)
6)
7)
8)
A total of 192 points (160 signal pin and 32 power pin LLCR test points) were measured.
EIA-364-23, Low Level Contact Resistance Test Procedure for Electrical Connectors and Sockets.
A computer program, LLCR 221.exe, ensures repeatability for data acquisition.
The following guidelines are used to categorize the changes in LLCR as a result from stressing.
a. <= +5.0 mOhms: --------------------------- Stable
b. +5.1 to +10.0 mOhms: --------------------- Minor
c. +10.1 to +15.0 mOhms: ------------------- Acceptable
d. +15.1 to +50.0 mOhms: ------------------- Marginal
e. +50.1 to +2000 mOhms ------------------- Unstable
f. >+2000 mOhms:---------------------------- Open Failure
LLCR Measurement Summaries by Pin Type
Date
Room Temp (Deg C)
Rel Humidity (%)
5/29/2013
23
60
Peter
Chen
Actual
Initial
6/6/2013
6/18/2013
23
23
58
56
Peter
Chen
Peter Chen
Delta
Delta
100 Cycles
Therm Shck
Pin Type 1: Signal
7/2/2013
23
56
Peter
Chen
Delta
Humidity
Average
St. Dev.
Min
Max
Summary Count
Total Count
19.21
1.76
14.66
23.00
160
160
1.27
1.30
0.02
7.93
160
160
Average
St. Dev.
Min
Max
Summary Count
Total Count
0.25
0.02
0.22
0.30
32
32
0.93
0.91
0.86
0.84
0.01
0.00
4.39
4.34
160
160
160
160
Pin Type 2: Power
0.02
0.02
0.02
0.02
0.00
0.00
0.09
0.08
32
32
32
32
Technician
mOhm values
0.11
0.09
0.00
0.44
32
32
LLCR Delta Count by Category
mOhms
100 Cycles
Therm Shck
Humidity
Stable
<=5
192
192
187
Minor
>5 & <=10
0
0
5
Acceptable
>10 & <=15
0
0
0
Page 47 of 54
Marginal
>15 & <=50
0
0
0
Unstable
>50 & <=1000
0
0
0
Open
>1000
0
0
0
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
DATA SUMMARIES Continued
LLCR thermal aging-0.056” thick card
1)
2)
3)
4)
A total of 192 points (160 signal pin and 32 power pin LLCR test points) were measured
EIA-364-23, Low Level Contact Resistance Test Procedure for Electrical Connectors and Sockets.
A computer program, LLCR 221.exe, ensures repeatability for data acquisition.
The following guidelines are used to categorize the changes in LLCR as a result from stressing.
a. <= +5.0 mOhms: --------------------------- Stable
b. +5.1 to +10.0 mOhms: --------------------- Minor
c. +10.1 to +15.0 mOhms: ------------------- Acceptable
d. +15.1 to +50.0 mOhms: ------------------- Marginal
e. +50.1 to +2000 mOhms ------------------- Unstable
f. >+2000 mOhms:---------------------------- Open Failure
LLCR Measurement Summaries by Pin Type
Date
Room Temp (Deg C)
Rel Humidity (%)
Technician
mOhm values
6/13/2013
23
56
Peter Chen
Actual
Initial
6/25/2013
23
56
Peterc Chen
Delta
Thermal
Pin Type 1: Signal
Average
St. Dev.
Min
Max
Summary Count
Total Count
19.02
1.79
15.40
23.11
160
160
Average
St. Dev.
Min
Max
Summary Count
Total Count
0.27
0.03
0.22
0.34
32
32
2.72
2.02
0.03
9.06
160
160
Pin Type 2: Power
0.21
0.16
0.01
0.52
32
32
Delta
Delta
LLCR Delta Count by Category
mOhms
Thermal
Stable
<=5
170
Minor
>5 & <=10
22
Acceptable
>10 & <=15
0
Marginal
>15 & <=50
0
Page 48 of 54
Unstable
>50 & <=1000
0
Open
>1000
0
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
DATA SUMMARIES Continued
LLCR thermal aging-0.068” thick card
5)
6)
7)
8)
A total of 192 points (160 signal pin and 32 power pin LLCR test points) were measured
EIA-364-23, Low Level Contact Resistance Test Procedure for Electrical Connectors and Sockets.
A computer program, LLCR 221.exe, ensures repeatability for data acquisition.
The following guidelines are used to categorize the changes in LLCR as a result from stressing.
g. <= +5.0 mOhms: --------------------------- Stable
h. +5.1 to +10.0 mOhms: --------------------- Minor
i. +10.1 to +15.0 mOhms: ------------------- Acceptable
j. +15.1 to +50.0 mOhms: ------------------- Marginal
k. +50.1 to +2000 mOhms ------------------- Unstable
l. >+2000 mOhms:---------------------------- Open Failure
LLCR Measurement Summaries by Pin Type
Date
Room Temp (Deg C)
Rel Humidity (%)
Technician
mOhm values
6/13/2013
23
56
Peter Chen
Actual
Initial
6/25/2013
23
58
Peter Chen
Delta
Thermal
Pin Type 1: Signal
Average
St. Dev.
Min
Max
Summary Count
Total Count
18.48
1.86
14.40
22.73
160
160
Average
St. Dev.
Min
Max
Summary Count
Total Count
0.23
0.02
0.21
0.28
32
32
1.14
1.08
0.02
5.81
160
160
Pin Type 2: Power
0.08
0.06
0.01
0.23
32
32
Delta
Delta
LLCR Delta Count by Category
mOhms
Thermal
Stable
<=5
191
Minor
>5 & <=10
1
Acceptable
>10 & <=15
0
Marginal
>15 & <=50
0
Page 49 of 54
Unstable
>50 & <=1000
0
Open
>1000
0
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
DATA SUMMARIES Continued
LLCR GAS TIGHT:
1)
2)
3)
4)
A total of 192 points (160 signal pin and 32 power pin LLCR test points) were measured
EIA-364-23, Low Level Contact Resistance Test Procedure for Electrical Connectors and Sockets.
A computer program, LLCR 221.exe, ensures repeatability for data acquisition.
The following guidelines are used to categorize the changes in LLCR as a result from stressing.
a. <= +5.0 mOhms: --------------------------- Stable
b. +5.1 to +10.0 mOhms: --------------------- Minor
c. +10.1 to +15.0 mOhms: ------------------- Acceptable
d. +15.1 to +50.0 mOhms: ------------------- Marginal
e. +50.1 to +2000 mOhms: ------------------ Unstable
f. >+2000 mOhms:---------------------------- Open Failure
LLCR Measurement Summaries by Pin Type
Date
Room Temp (Deg C)
Rel Humidity (%)
Technician
mOhm values
5/29/2013
23
60
Peter Chen
Actual
Initial
6/6/2013
23
58
Peter Chen
Delta
Acid Vapor
Pin Type 1: Signal
Average
St. Dev.
Min
Max
Summary Count
Total Count
19.09
1.71
15.28
22.70
160
160
Average
St. Dev.
Min
Max
Summary Count
Total Count
0.28
0.03
0.23
0.33
32
32
0.41
0.57
0.00
4.54
160
160
Pin Type 2: Power
0.02
0.02
0.00
0.09
32
32
Delta
Delta
LLCR Delta Count by Category
mOhms
Acid Vapor
Stable
<=5
192
Minor
>5 & <=10
0
Acceptable
>10 & <=15
0
Marginal
>15 & <=50
0
Page 50 of 54
Unstable
>50 & <=1000
0
Open
>1000
0
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
DATA SUMMARIES Continued
LLCR Shock Vib-0.056” thick card:
1)
2)
3)
4)
A total of 192 points(160 signal pin and 32 power pin LLCR test points) were measured
EIA-364-23, Low Level Contact Resistance Test Procedure for Electrical Connectors and Sockets.
A computer program, LLCR 221.exe, ensures repeatability for data acquisition.
The following guidelines are used to categorize the changes in LLCR as a result from stressing.
a. <= +5.0 mOhms: --------------------------- Stable
b. +5.1 to +10.0 mOhms: --------------------- Minor
c. +10.1 to +15.0 mOhms: ------------------- Acceptable
d. +15.1 to +50.0 mOhms: ------------------- Marginal
e. +50.1 to +2000 mOhms: ------------------ Unstable
f. >+2000 mOhms:---------------------------- Open Failure
LLCR Measurement Summaries by Pin Type
Date
Room Temp (Deg C)
Rel Humidity (%)
Technician
mOhm values
6/27/2013
22
50
Tony Wagoner
Actual
Initial
7/11/2013
22
52
Tony Wagoner
Delta
Shock-Vib
Pin Type 1: Row 1
Average
St. Dev.
Min
Max
Summary Count
Total Count
20.40
1.15
17.97
23.38
104
104
Average
St. Dev.
Min
Max
Summary Count
Total Count
16.66
0.83
14.72
18.23
56
56
Average
St. Dev.
Min
Max
Summary Count
Total Count
0.28
0.02
0.24
0.32
32
32
0.62
0.45
0.01
2.98
104
104
Pin Type 2: Row 2
0.40
0.49
0.01
3.48
56
56
Pin Type 3: Power
0.02
0.01
0.00
0.07
32
32
Delta
Delta
LLCR Delta Count by Category
mOhms
Shock-Vib
Stable
<=5
192
Minor
>5 & <=10
0
Acceptable
>10 & <=15
0
Marginal
>15 & <=50
0
Page 51 of 54
Unstable
>50 & <=1000
0
Open
>1000
0
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
DATA SUMMARIES Continued
LLCR Shock Vib-0.068” thick card:
5)
6)
7)
8)
A total of 192 points(160 signal pin and 32 power pin LLCR test points) were measured
EIA-364-23, Low Level Contact Resistance Test Procedure for Electrical Connectors and Sockets.
A computer program, LLCR 221.exe, ensures repeatability for data acquisition.
The following guidelines are used to categorize the changes in LLCR as a result from stressing.
g. <= +5.0 mOhms: --------------------------- Stable
h. +5.1 to +10.0 mOhms: --------------------- Minor
i. +10.1 to +15.0 mOhms: ------------------- Acceptable
j. +15.1 to +50.0 mOhms: ------------------- Marginal
k. +50.1 to +2000 mOhms: ------------------ Unstable
l. >+2000 mOhms:---------------------------- Open Failure
LLCR Measurement Summaries by Pin Type
Date
Room Temp (Deg C)
Rel Humidity (%)
Technician
mOhm values
6/27/2013
22
50
Tony Wagoner
Actual
Initial
7/8/2013
22
52
Tony Wagoner
Delta
Shock-Vib
Pin Type 1: Row 1
Average
St. Dev.
Min
Max
Summary Count
Total Count
20.35
1.18
17.98
23.35
104
104
Average
St. Dev.
Min
Max
Summary Count
Total Count
16.54
0.71
14.90
18.17
56
56
Average
St. Dev.
Min
Max
Summary Count
Total Count
0.23
0.02
0.20
0.28
32
32
0.57
0.63
0.01
3.13
104
104
Pin Type 2: Row 2
0.21
0.17
0.00
0.73
56
56
Pin Type 3: Power
0.02
0.01
0.00
0.04
32
32
Delta
Delta
LLCR Delta Count by Category
mOhms
Shock-Vib
Stable
<=5
192
Minor
>5 & <=10
0
Acceptable
>10 & <=15
0
Marginal
>15 & <=50
0
Page 52 of 54
Unstable
>50 & <=1000
0
Open
>1000
0
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
EQUIPMENT AND CALIBRATION SCHEDULES
Equipment #: HZ-MO-05
Description: Micro-ohmmeter
Manufacturer: Keithley
Model: 3706
Serial #: 297288
Accuracy: Last Cal: 2012-8-6, Next Cal: 2013-8-5
Equipment #: HZ-HPM-01
Description: IR/DWV Tester
Manufacturer: AN9636H
Model: AN9636H
Serial #: 089601091
Accuracy: Last Cal: 2013-7-6, Next Cal: 2014-7-5
Equipment #: HZ-TCT-01
Description: Normal force analyzer
Manufacturer: Mecmesin Multitester
Model: Mecmesin Multitester 2.5-i
Serial #: 08-1049-04
Accuracy: Last Cal: 2013-4-28, Next Cal: 2014-4-27
Equipment #: HZ-OV-01
Description: Oven
Manufacturer: Huida
Model: CS101-1E
Serial #: CS101-1E-B
Accuracy: Last Cal: 2012-12-14, Next Cal: 2013-12-13
Equipment #: HZ-THC-01
Description: Humidity transmitter
Manufacturer: Thermtron
Model: HMM30C
Serial #: D0240037
Accuracy: Last Cal: 2013-3-3, Next Cal: 2014-3-2
Equipment #: MO-02
Description: Multimeter /Data Acquisition System
Manufacturer: Keithley
Model: 2700
Serial #: 0780546
Accuracy: Last Cal: 2013-6-16, Next Cal: 2014-6-16
Page 53 of 54
Tracking Code: 259655_Report_Rev_1
Part #: LPHS-08-32-L-RT1-GP/Edge Card
Part description: LPHS / Card
EQUIPMENT AND CALIBRATION SCHEDULES
Equipment #: PS-01
Description: Power Supply
Manufacturer: Hewlett Packard
Model: 6033A
Serial #: 3329A-07330
Accuracy: Last Cal: 2013-6-12, Next Cal: 2014-6-12
Equipment #: PS-02
Description: Power Supply
Manufacturer: Hewlett Packard
Model: 6033A
Serial #: 2847A-04167
Accuracy: Last Cal: 2013-6-12, Next Cal: 2014-6-12
Equipment #: HZ-TSC-01
Description: Thermal Shock transmitter
Manufacturer: CSZ
Model: 10-VT14994
Serial #: VTS-3-6-6-SC/AC
Accuracy: Last Cal: 2012-11-1, Next Cal: 2013-11-1
Equipment #: SVC-01
Description: Shock & Vibration Table
Manufacturer: Data Physics
Model: LE-DSA-10-20K
Serial #: 10037
Accuracy: See Manual
… Last Cal: 2012-11-31, Next Cal: 2013-11-31
Equipment #: ACLM-01
Description: Accelerometer
Manufacturer: PCB Piezotronics
Model: 352C03
Serial #: 115819
Accuracy: See Manual
… Last Cal: 2013-07-9, Next Cal: 2014-7-9
Equipment #: ED-03
Description: Event Detector
Manufacturer: Analysis Tech
Model: 32EHD
Serial #: 1100604
Accuracy: See Manual
… Last Cal: 2013-06-4, Next Cal: 2014-06-4
Page 54 of 54