Product Specification Series: PES / PET .250’’ (6,35 mm) PowerStrip™/40 Amp High Power Socket and Terminal Strip PESC / PETC .250” (6,35mm) PowerStrip™/40 Amp High Power Combo Socket and Terminal Strip PES Series – Socket, Vertical Orientation PESC Series – Combo Socket, Vertical Orientation PET Series – Terminal, Vertical Orientation PETC Series – Combo Terminal, Vertical Orientation Other configurations available for: Right Angle applications Cable Assembly applications See www.samtec.com for more information. Revision: C Date: August 27, 2015 Page 1 © Samtec, Inc. Product Specification Series: PES / PET .250’’ (6,35 mm) PowerStrip™/40 Amp High Power Socket and Terminal Strip PESC / PETC .250” (6,35mm) PowerStrip™/40 Amp High Power Combo Socket and Terminal Strip 1.0 SCOPE 1.1 This specification covers performance, testing and quality requirements for Samtec PES / PET Series .250’’ (6,35 mm) PowerStrip™/40 Amp High Power Socket and Terminal Strip system and PESC / PETC Series Signal/Power Combo Socket and Terminal Strip system . All information contained in this specification is for a Vertical socket / Vertical terminal mated configuration unless otherwise noted. Right Angle socket / Right Angle terminal mated configuration is available on www.samtec.com. 2.0 DETAILED INFORMATION 2.1 Product prints, footprints, catalog pages, test reports and other specific, detailed information can be found at www.samtec.com?PES, www.samtec.com?PET, http://www.samtec.com/?PESC and http://www.samtec.com/?PETC 3.0 TESTING 3.1 Current Rating: Power Contact 31A (One Pin Powered Per Row) Signal Contacts 5.7A (4 Pins Powered Per Row) 3.2 Voltage Rating: 450 VAC 3.3 Operating Temperature Range: -55°C to +125°C 3.4 Electrical: ITEM TEST CONDITION REQUIREMENT STATUS Withstanding Voltage EIA-364-20 (No Flashover, Sparkover, or Breakdown) 1350 VAC Pass Insulation Resistance EIA-364-21 (1000 MΩ minimum) 15,000 MΩ Pass EIA-364-23 Power Δ 5 mΩ maximum / Signal Δ 15 mΩ (Samtec defined)/ No damage Pass REQUIREMENT STATUS Contact Resistance (LLCR) 3.5 Mechanical: ITEM TEST CONDITION Durability EIA-364-09C 100 cycles Random Vibration EIA-364-28 Condition V, Letter B 7.56 G 'RMS', 50 to 2000 Hz, 2 hours per axis, 3 axis total , PSD 0.04 Visual Inspection: No Damage LLCR: Power Δ 5 mΩ maximum / Signal Δ 15 mΩ Mechanical Shock EIA-364-27 100 G, 6 milliseconds, sawtooth wave, 11.3 fps, 3 shocks/direction, 3 axis (18 total shocks) Visual Inspection: No Damage LLCR: Power Δ 5 mΩ maximum / Signal Δ 15 mΩ Normal Force EIA-364-04 30 grams minimum for Gold interface Revision: C Date: August 27, 2015 Page 2 Pass Pass Pass Pass © Samtec, Inc. Product Specification Series: PES / PET .250’’ (6,35 mm) PowerStrip™/40 Amp High Power Socket and Terminal Strip PESC / PETC .250” (6,35mm) PowerStrip™/40 Amp High Power Combo Socket and Terminal Strip 3.6 Environmental: ITEM TEST CONDITION REQUIREMENT STATUS Thermal Shock EIA-364-32 Thermal Cycles: 100 (30 minute dwell) Hot Temp: +85°C Cold Temp: -55°C Hot/Cold Transition: Immediate Visual Inspection: No Damage LLCR: Power Δ 5 mΩ / Signal Δ 15 mΩ DWV: 1350 VAC IR: >15,000 MΩ Pass Thermal Aging (Temp Life) EIA-364-17 Test Condition 4 @ 105°C Condition B for 250 hours Visual Inspection: No Damage LLCR: Power Δ 5 mΩ / Signal Δ 15 mΩ DWV: 1350 VAC IR: >15,000 MΩ Pass Cyclic Humidity EIA-364-31 Test Temp: +25°C to +65°C Relative Humidity: 90 to 95% Test Duration: 240 hours Visual Inspection: No Damage LLCR: Δ 5 mΩ DWV: 1350 VAC IR: >15,000 MΩ Pass Gas Tight EIA-364-36 Gas Exposure: Nitric Acid Vapor Duration: 60 min. Drying Temp.: 50°C +/- 3°C Measurements: Within 1 hour of Exposure LLCR: Power Δ 5 mΩ / Signal Δ 15 mΩ Pass 4.0 MATED SYSTEM 4.1 Mated Views Mated view information can be found at link below: http://suddendocs.samtec.com/prints/pexx-xx%20mated%20document.pdf Revision: C Date: August 27, 2015 Page 3 © Samtec, Inc. Product Specification Series: PES / PET .250’’ (6,35 mm) PowerStrip™/40 Amp High Power Socket and Terminal Strip PESC / PETC .250” (6,35mm) PowerStrip™/40 Amp High Power Combo Socket and Terminal Strip 5.0 POLARIZING FEATURES 6.0 PROCESSING RECOMMENDATIONS 6.1 Mating Alignment Requirements: 6.1.1 Revision: C Maximum guidance/capture in applications where at least one half of the interface is free to float. Date: August 27, 2015 Page 4 © Samtec, Inc. Product Specification Series: PES / PET .250’’ (6,35 mm) PowerStrip™/40 Amp High Power Socket and Terminal Strip PESC / PETC .250” (6,35mm) PowerStrip™/40 Amp High Power Combo Socket and Terminal Strip 6.1.2 For PES / PET, the parts can be rigidly misaligned by no more than .010” (0,25 mm) in the X- and .010” (0,25 mm) in the Y-direction to ensure a good mate. 6.1.3 For PESC / PETC, the parts can be rigidly misaligned by no more than .003” (0,08 mm) in the Xand .003” (0,08 mm) in the Y-direction to ensure a good mate. 6.2 Mating Angle Requirements: The connector can’t be zippered in both the longitudinal and lateral directions. 6.2.1 Revision: C Date: August 27, 2015 Page 5 © Samtec, Inc. Product Specification Series: PES / PET .250’’ (6,35 mm) PowerStrip™/40 Amp High Power Socket and Terminal Strip PESC / PETC .250” (6,35mm) PowerStrip™/40 Amp High Power Combo Socket and Terminal Strip 6.2.2 7.0 ADDITIONAL RESOURCES 7.1 For additional mechanical testing or product information, contact our Customer Engineering Support Group at [email protected] 7.2 For additional information on high speed performance testing, contact our Signal Integrity Group at [email protected] 7.3 For additional processing information, contact our Interconnect Processing Group at [email protected]. 7.4 For RoHS, REACH or other environmental compliance information, contact our Product Environmental Compliance Group at [email protected] USE OF PRODUCT SPECIFICATION SHEET This Product Specification Sheet (“PSS”) is a brief summary of information related to the Product identified. As a summary, it should only be used for the limited purpose of considering the purchase/use of Product. For specific, detailed information, including but not limited to testing and Product footprint, refer to Section 2.0 of this document and the links there provided to test reports and prints. This PSS is the property of Samtec, Inc. (“Samtec”) and contains proprietary information of Samtec, our various licensors, or both. Samtec does not grant express or implied rights or license under any patent, copyright, trademark or other proprietary rights and the use of the PSS for building, reverse engineering or replication is strictly prohibited. By using the PSS, the user agrees to not infringe, directly or indirectly, upon any intellectual property rights of Samtec and acknowledges that Samtec, our various licensors, or both own all intellectual property therein. The PSS is presented “AS IS”. While Samtec makes every effort to present excellent information, the PSS is only provided as a guideline and does not, therefore, warrant it is without error or defect or that the PSS contains all necessary and/or relevant information about the Product. The user agrees that all access and use of the PSS is at its own risk. NO WARRANTIES EXPRESSED OR IMPLIED, INCLUDING ANY WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR OF ANY KIND WHATSOEVER ARE PROVIDED. Revision: C Date: August 27, 2015 Page 6 © Samtec, Inc.