NX-series Digital Mixed I/O Units NX-MD CSM_NX-MD_DS_E_2_1 Digital Mixed I/O Units for High speed Synchronous Control • DC Input/Transistor Output Units for the NX-series modular I/O system. • Connect to other NX-series I/O Units and EtherCAT Coupler units using the high-speed NX-bus. • One Unit enables synchronous Units to update the status of input devices to the controller and the output status of synchronous Units according to the controller's instructions every EtherCAT cycle. Features • High-speed I/O refreshing is possible by connecting with the NX-series EtherCAT Coupler. • Output refreshing can be synchronized with the control cycle of the Controller. (Synchronous refreshing) • Connector Types significantly reduces wiring work. System Configuration Sysmac Studio Support Software Connection to peripheral USB port or built-in EtherNet/IPTM port on NJ/NX-series CPU Unit EtherCAT master* NJ/NX-series CPU Unit or master from another manufacturer Built-in EtherCAT port Sysmac Studio Support Software ●EtherCAT Slave Terminal Communications cable Ethernet cables Peripheral USB port. NX Series EtherCAT Coupler Unit NX-ECC@@@ Connection to peripheral USB port on EtherCAT Coupler Unit .xml ESI files NX Units End Cover * Refer to Versions information on the unit versions of CPU Units when you connect an EtherCAT Slave Terminal to the built-in EtherCAT port on an OMRON NJ/NX-series CPU Unit. OMRON CJ1W-NC@81/@82 Position Control Units cannot be connected to the EtherCAT Slave Terminal even though they support EtherCAT. Sysmac is a trademark or registered trademark of OMRON Corporation in Japan and other countries for OMRON factory automation products. EtherCAT® is a registered trademark of Beckhoff Automation GmbH for their patented technology. EtherNet/IPTM is the trademarks of ODVA. Other company names and product names in this document are the trademarks or registered trademarks of their respective companies. 1 NX-MD Ordering Information International Standards • The standards are abbreviated as follows: U: UL, U1: UL (Class I Division 2 Products for Hazardous Locations), C: CSA, UC: cULus, UC1: cULus (Class I Division 2 Products for Hazardous Locations), CU: cUL, N: NK, L: Lloyd, CE: EC Directives,and KC: KC Registration. • Contact your OMRON representative for further details and applicable conditions for these standards. Digital Mixed I/O Unit ● DC Input/Transistor Output Units (MIL Connector, 30 mm Width) Specification Product Name Unit type Number of points Outputs: 16 points Inputs: 16 points Rated voltage I/O refreshing method UC1, CE, KC Outputs: 0.5 ms max./ 1.0 ms max. Inputs: 20 μs max./ 400 μs max. Outputs: 24 VDC Inputs: 24 VDC Standards NX-MD6121-5 Switching Synchronous I/O refreshing and Free-Run refreshing 0.5 A/point, 2 A/Unit Outputs: PNP Inputs: For both NPN/PNP Model ON/OFF response time Outputs: 0.1 ms max./ 0.8 ms max. Inputs: 20 μs max./ 400 μs max. Outputs: 12 to 24 VDC Inputs: 24 VDC Outputs: NPN Inputs: For both NPN/PNP DC Input/ Transistor Output Units NX Series Digital Mixed I/O Units Internal I/O common Maximum value of load current NX-MD6256-5 ● DC Input/Transistor Output Units (Fujitsu Connector, 30 mm Width) Specification Product Name Unit type Number of points Internal I/O common Maximum value of load current Rated voltage I/O refreshing method ON/OFF response time Model Standards Transistor Output Units NX Series Digital Output Units Outputs: 16 points Inputs: 16 points Outputs: NPN Inputs: For both NPN/PNP 0.5 A/point, 2 A/Unit Switching Outputs: Synchronous 12 to 24 VDC I/O refreshing and Inputs: Free-Run 24 VDC refreshing Outputs: 0.1 ms max./ 0.8 ms max. Inputs: 20 μs max./ 400 μs max. NX-MD6121-6 UC1, CE, KC Accessories Not included. 2 NX-MD General Specification Item Grounding method Operating environment Specification Mounted in a panel Enclosure Ground to 100 Ω or less Ambient operating temperature 0 to 55°C Ambient operating humidity 10% to 95% (with no condensation or icing) Atmosphere Must be free from corrosive gases. Ambient storage temperature −25 to 70°C (with no condensation or icing) Altitude 2,000 m max. Pollution degree 2 or less: Conforms to JIS B3502 and IEC 61131-2. Noise immunity 2 kV on power supply line (Conforms to IEC61000-4-4.) Overvoltage category Category II: Conforms to JIS B3502 and IEC 61131-2. EMC immunity level Zone B Vibration resistance *1 Conforms to IEC 60068-2-6. 5 to 8.4 Hz with 3.5-mm amplitude, 8.4 to 150 Hz, acceleration of 9.8 m/s2, 100 min each in X, Y, and Z directions (10 sweeps of 10 min each = 100 min total) Shock resistance *1 Conforms to IEC 60068-2-27. 147 m/s2, 3 times each in X, Y, and Z directions cULus: Listed UL508 and ANSI/ISA 12.12.01 EC: EN 61131-2 and C-Tick, KC: KC Registration, NK, LR *1 For the Relay Output Unit, refer to the Digital Input Unit Specifications. *2 Refer to the OMRON website (http://www.ia.omron.com/) or consult your OMRON representative for the most recent applicable standards for each model. Applicable standards *2 3 NX-MD Digital Mixed I/O Unit Specifications ● DC Input/Transistor Output Units (MIL Connector, 30 mm Width) NX-MD6121-5 Unit name DC Input/Transistor Output Unit Model NX-MD6121-5 Number of points 16 inputs/16 outputs External connection terminals 2 MIL connectors (20 terminals) I/O refreshing method Switching Synchronous I/O refreshing and Free-Run refreshing Output section (CN1) Internal I/O common NPN Internal I/O common For both NPN/PNP Rated voltage 12 to 24 VDC Rated input voltage 24 VDC (15 to 28.8 VDC) Operating load voltage range 10.2 to 28.8 VDC Input current 7 mA typical (at 24 VDC) Maximum value of load current 0.5 A/point, 2 A/Unit ON voltage/ON current 15 VDC min./3 mA min. (between COM and each signal) Maximum inrush current 4.0 A/point, 10 ms max. OFF voltage/OFF current 5 VDC max./1 mA max. (between COM and each signal) Leakage current 0.1 mA max. Residual voltage 1.5 V max. Input section (CN2) ON/OFF response 20 μs max./400 μs max. time Input filter time ON/OFF response 0.1 ms max./0.8 ms max. time TS indicator, I/O indicators Indicators No filter, 0.25 ms, 0.5 ms, 1 ms (default), 2 ms, 4 ms, 8 ms, 16 ms, 32 ms, 64 ms, 128 ms, 256 ms Dimensions 30 (W) x 100 (H) x 71 (D) Isolation method Photocoupler isolation Insulation resistance 20 MΩ min. between isolated circuits (at 100 VDC) Dielectric strength 510 VAC between isolated circuits for 1 minute at a leakage current of 5 mA max. I/O power supply method Supply from external source Current capacity of I/O power supply terminal Without I/O power supply terminals NX Unit power consumption 0.70 W max. Current consumption from I/O power supply 30 mA max. Weight 105 g max. CN1 (left) output circuit Internal circuits +V0 +V0 Connector COM0 COM0 I/O power supply + NX bus connector I/O power (right) supply − I/O power NX bus connector supply + I/O power (left) supply − CN2 (right) input circuit Input indicator Connector IN0 to IN15 COM1 COM1 I/O power NX bus connector supply + I/O power (left) supply − 3.3 kΩ Internal circuits Circuit layout OUT0 to OUT15 I/O power supply + NX bus connector I/O power (right) supply − 4 NX-MD Installation orientation: Possible in 6 orientations. Restrictions: As shown in the following. Installation orientation and restrictions Number of simultaneously ON input points • For upright installation Number of simultaneously ON input points vs. Ambient temperature characteristic 16 points at 35°C 16 points at 45°C 16 13 points at 55°C 12 9 points at 55°C 8 I/O power supply voltage 24 V 4 28.8 V 0 0 10 20 30 40 45 50 55 60 Ambient temperature (°C) Number of simultaneously ON input points • For any installation other than upright Number of simultaneously ON input points vs. Ambient temperature characteristic 16 points at 40°C 16 points at 25°C 16 12 8 4 0 I/O power supply voltage 24 V 5 points at 55°C 28.8 V 3 points at 55°C 0 10 20 30 40 45 50 55 60 Ambient temperature (°C) CN1 (left) output terminal Signal Connector Signal name pin name OUT0 20 19 OUT8 L OUT1 18 17 OUT9 L OUT2 16 15 OUT10 L OUT3 14 13 OUT11 L OUT4 12 11 OUT12 L OUT5 10 9 OUT13 L OUT6 8 7 OUT14 L OUT7 6 5 OUT15 L COM0 4 3 COM0 +V0 2 1 +V0 L L L L L L L L 12 to 24 VDC Terminal connection diagram • Be sure to wire both pins 3 and 4 (COM0) of CN1. • Be sure to wire both pins 1 and 2 (+V0) of CN1. CN2 (right) input terminal 24 VDC Signal Connector Signal name pin name NC 1 2 NC COM1 3 4 COM1 IN15 5 6 IN07 IN14 7 8 IN06 IN13 9 10 IN05 IN12 11 12 IN04 IN11 13 14 IN03 IN10 15 16 IN02 IN09 17 18 IN01 IN08 19 20 IN00 • The polarity of the input power supply of CN2 can be connected in either direction. • Be sure to wire both pins 3 and 4 (COM1) of CN2, and set the same polarity for both pins. Disconnection/Short-circuit detection Not supported. Protective function Not supported. 5 NX-MD NX-MD6256-5 Unit name DC Input/Transistor Output Unit Model NX-MD6256-5 Number of points 16 inputs/16 outputs External connection terminals 2 MIL connectors (20 terminals) I/O refreshing method Switching Synchronous I/O refreshing and Free-Run refreshing Output section (CN1) Internal I/O common PNP Internal I/O common For both NPN/PNP Rated voltage 24 VDC Rated input voltage 24 VDC (15 to 28.8 VDC) Operating load voltage range 20.4 to 28.8 VDC Input current 7 mA typical (at 24 VDC) Maximum value of load current 0.5 A/point, 2 A/Unit ON voltage/ON current 15 VDC min./3 mA min. (between COM and each signal) Maximum inrush current 4.0 A/point, 10 ms max. OFF voltage/OFF current 5 VDC max./1 mA max. (between COM and each signal) Leakage current 0.1 mA max. Residual voltage 1.5 V max. Input section (CN2) ON/OFF response 20 μs max./400 μs max. time Input filter time ON/OFF response 0.5 ms max./1.0 ms max. time TS indicator, I/O indicators Indicators No filter, 0.25 ms, 0.5 ms, 1 ms (default), 2 ms, 4 ms, 8 ms, 16 ms, 32 ms, 64 ms, 128 ms, 256 ms Dimensions 30 (W) x 100 (H) x 71 (D) Isolation method Photocoupler isolation Insulation resistance 20 MΩ min. between isolated circuits (at 100 VDC) Dielectric strength 510 VAC between isolated circuits for 1 minute at a leakage current of 5 mA max. I/O power supply method Supply from external source Current capacity of I/O power supply terminal Without I/O power supply terminals NX Unit power consumption 0.75 W max. Current consumption from I/ O power supply 40 mA max. Weight 110 g max. Connector OUT0 to OUT15 0V0 0V0 I/O power supply + NX bus connector I/O power (right) supply − I/O power NX bus connector supply + I/O power (left) supply − CN2 (right) input circuit Input indicator Connector IN0 to IN15 COM1 COM1 I/O power NX bus connector supply + I/O power (left) supply − 3.3 kΩ Internal circuits Circuit layout COM0 (+V) COM0 (+V) Short-circuit protection Internal circuits CN1 (left) output circuit I/O power supply + NX bus connector I/O power (right) supply − 6 NX-MD Installation orientation: Possible in 6 orientations. Restrictions: As shown in the following. Installation orientation and restrictions Number of simultaneously ON input points • For upright installation Number of simultaneously ON input points vs. Ambient temperature characteristic 16 points at 35°C 16 points at 45°C 16 13 points at 55°C 12 9 points at 55°C 8 I/O power supply voltage 24 V 4 28.8 V 0 0 10 20 30 40 45 50 55 60 Ambient temperature (°C) Number of simultaneously ON input points • For any installation other than upright Number of simultaneously ON input points vs. Ambient temperature characteristic 16 points at 40°C 16 points at 25°C 16 12 8 4 0 0 I/O power supply voltage 24 V 5 points at 55°C 28.8 V 3 points at 55°C 10 20 30 40 45 50 55 60 Ambient temperature (°C) CN1 (left) output terminal Signal Connector Signal name pin name OUT0 20 19 OUT8 L OUT1 18 17 OUT9 L OUT2 16 15 OUT10 L OUT3 14 13 OUT11 L OUT4 12 11 OUT12 L OUT5 10 9 OUT13 L OUT6 8 7 OUT14 L OUT7 6 5 OUT15 L COM0 (+V) 4 3 COM0 (+V) 0V0 2 1 0V0 L L L L L L L L 24 VDC Terminal connection diagram • Be sure to wire both pins 3 and 4 (COM0 (+V)) of CN1. • Be sure to wire both pins 1 and 2 (0V0) of CN1. CN2 (right) input terminal 24 VDC Signal Connector Signal name pin name NC 1 2 NC COM1 3 4 COM1 IN15 5 6 IN07 IN14 7 8 IN06 IN13 9 10 IN05 IN12 11 12 IN04 IN11 13 14 IN03 IN10 15 16 IN02 IN09 17 18 IN01 IN08 19 20 IN00 • The polarity of the input power supply of CN2 can be connected in either direction. • Be sure to wire both pins 3 and 4 (COM1) of CN2, and set the same polarity for both pins. Disconnection/Short-circuit detection Not supported. Protective function With load short-circuit protection. 7 NX-MD ● DC Input/Transistor Output Units (Fujitsu Connector, 30 mm Width) NX-MD6121-6 Unit name DC Input/Transistor Output Unit Model NX-MD6121-6 Number of points 16 inputs/16 outputs External connection terminals 2 Fujitsu connectors (24 terminals) I/O refreshing method Switching Synchronous I/O refreshing and Free-Run refreshing Output section (CN1) Internal I/O common NPN Internal I/O common For both NPN/PNP Rated voltage 12 to 24 VDC Rated input voltage 24 VDC (15 to 28.8 VDC) Operating load voltage range 10.2 to 28.8 VDC Input current 7 mA typical (at 24 VDC) Maximum value of load current 0.5 A/point, 2 A/Unit ON voltage/ON current 15 VDC min./3 mA min. (between COM and each signal) Maximum inrush current 4.0 A/point, 10 ms max. OFF voltage/OFF current 5 VDC max./1 mA max. (between COM and each signal) Leakage current 0.1 mA max. ON/OFF response time 20 μs max./400 μs max. Input filter time No filter, 0.25 ms, 0.5 ms, 1 ms (default), 2 ms, 4 ms, 8 ms, 16 ms, 32 ms, 64 ms, 128 ms, 256 ms Input section (CN2) Residual voltage 1.5 V max. ON/OFF response time 0.1 ms max./0.8 ms max. TS indicator, I/O indicators Indicators Dimensions 30 (W) x 100 (H) x 71 (D) Isolation method Photocoupler isolation Insulation resistance 20 MΩ min. between isolated circuits (at 100 VDC) Dielectric strength 510 VAC between isolated circuits for 1 minute at a leakage current of 5 mA max. I/O power supply method Supply from external source Current capacity of I/O power supply terminal Without I/O power supply terminals NX Unit power consumption 0.70 W max. Current consumption from I/O power supply 30 mA max. Weight 95 g max. CN1 (left) output circuit +V0 Internal circuits +V0 Connector COM0 COM0 I/O power supply + I/O power supply − I/O power supply + I/O power supply − NX bus connector (right) CN2 (right) input circuit Input indicator 3.3 kΩ IN0 to IN15 Connector COM1 NX bus connector (left) COM1 I/O power supply + I/O power supply − Internal circuits Circuit layout NX bus connector (left) OUT0 to OUT15 I/O power supply + I/O power supply − NX bus connector (right) 8 NX-MD Installation orientation: Possible in 6 orientations. Restrictions: As shown in the following. • For upright installation 16 points at 35°C 16 points at 45°C 16 13 points at 55°C 12 9 points at 55°C 8 I/O power supply voltage 24 V 4 28.8 V 0 0 10 20 30 40 45 50 55 60 Ambient temperature (°C) • For any installation other than upright Number of simultaneously ON input points vs. Ambient temperature characteristic Number of simultaneously ON input points Installation orientation and restrictions Number of simultaneously ON input points Number of simultaneously ON input points vs. Ambient temperature characteristic 16 points at 40°C 16 points at 25°C 16 12 I/O power supply voltage 8 5 points at 55°C 24 V 4 28.8 V 0 0 10 3 points at 55°C 20 30 40 45 50 55 60 Ambient temperature (°C) 9 NX-MD CN1 (left) output terminal Signal name Connector Signal name pin B A NC B12 A12 NC NC B11 A11 NC +V0 B10 A10 +V0 L L L L L L L L COM0 B9 A9 COM0 OUT15 B8 A8 OUT7 OUT14 B7 A7 OUT6 OUT13 B6 A6 OUT5 OUT12 B5 A5 OUT4 OUT11 B4 A4 OUT3 OUT10 B3 A3 OUT2 OUT9 B2 A2 OUT1 OUT8 B1 A1 OUT0 L L L L L L L L 12 to 24 VDC Terminal connection diagram • Be sure to wire both pins A9 and B9 (COM0) of CN1. • Be sure to wire both pins A10 and B10 (+V0) of CN1. CN2 (right) input terminal Signal name Connector Signal name pin A B IN0 A1 B1 IN8 IN1 A2 B2 IN9 IN2 A3 B3 IN10 IN3 A4 B4 IN11 IN4 A5 B5 IN12 IN5 A6 B6 IN13 IN6 A7 B7 IN14 IN7 A8 B8 IN15 COM1 A9 B9 COM1 NC A10 B10 NC NC A11 B11 NC 24 VDC NC A12 B12 NC • The polarity of the input power supply of CN2 can be connected in either direction. • Be sure to wire both pins A9 and B9 (COM1) of CN2, and set the same polarity for both pins. Disconnection/Short-circuit detection Not supported. Protective function Not supported. 10 NX-MD Version Information NX Units Corresponding Unit Versions/Versions * EtherCAT Model NX-MD6121-5 Unit version Ver.1.0 Communications Coupler Units NX-ECC20@ Ver.1.0 NJ/NX series CPU Units NJ501-@@@@ NJ301-@@@@ NJ101-@@@@ NX701-@@@@ Ver.1.05 EtherNet/IP Sysmac Studio Ver.1.10 Communications Coupler Units NX-EIC202 Ver.1.0 Sysmac Studio Ver.1.10 NX-MD6121-6 Ver.1.13 Ver.1.13 NX-MD6256-5 Ver.1.10 Ver.1.10 * Some Units do not have all of the versions given in the above table. If a Unit does not have the specified version, support is provided by the oldest available version after the specified version. Refer to the user’s manuals for the specific Units for the relation between models and versions. 11 NX-MD External Interface Connector Types NX Units (30 mm Width) ● Units with MIL Connectors (2 Connectors with 20 Terminals) (A) (B) (C) Letter Name Function (A) NX bus connector This connector is used to connect each Unit. (B) Indicators The indicators show the current operating status of the Unit. (C) Connectors The connectors are used to connect to external devices. The number of terminals depends on the type of Unit. ● Units with Fujitsu Connectors (2 Connectors with 24 Terminals) (A) (B) (C) Letter (A) Name Function NX bus connector This connector is used to connect each Unit. (B) Indicators The indicators show the current operating status of the Unit. (C) Connectors The connectors are used to connect to external devices. 12 NX-MD Dimensions (Unit/mm) Connector Types 30 mm Width ● Units with MIL Connectors (2 Connectors with 20 Terminals) 16.1 1.5 104.5 100 58.3 27.85 8.9 1.5 65.2 19.1 71 30 89.52 32.1 ● Units with Fujitsu Connectors (2 Connectors with 24 Terminals) 16.1 1.5 104.5 100 27.85 1.5 8.6 65.2 19.4 71 30 72.5 (118.5) 32.1 Related Manuals Cat. No. W521 Model number NX-IA@@@@ NX-ID@@@@ NX-OD@@@@ NX-OC@@@@ NX-MD@@@@ Manual name NX-series Digital I/O Units User’s Manual Application Description Learning how to use NX-series The hardware, setup methods, and functions of the NXDigital I/O Units series Digital I/O Units are described. 13 Terms and Conditions Agreement Read and understand this catalog. Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. Warranties. (a) Exclusive Warranty. Omron’s exclusive warranty is that the Products will be free from defects in materials and workmanship for a period of twelve months from the date of sale by Omron (or such other period expressed in writing by Omron). Omron disclaims all other warranties, express or implied. (b) Limitations. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, ABOUT NON-INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OF THE PRODUCTS. BUYER ACKNOWLEDGES THAT IT ALONE HAS DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. Omron further disclaims all warranties and responsibility of any type for claims or expenses based on infringement by the Products or otherwise of any intellectual property right. (c) Buyer Remedy. Omron’s sole obligation hereunder shall be, at Omron’s election, to (i) replace (in the form originally shipped with Buyer responsible for labor charges for removal or replacement thereof) the non-complying Product, (ii) repair the non-complying Product, or (iii) repay or credit Buyer an amount equal to the purchase price of the non-complying Product; provided that in no event shall Omron be responsible for warranty, repair, indemnity or any other claims or expenses regarding the Products unless Omron’s analysis confirms that the Products were properly handled, stored, installed and maintained and not subject to contamination, abuse, misuse or inappropriate modification. Return of any Products by Buyer must be approved in writing by Omron before shipment. Omron Companies shall not be liable for the suitability or unsuitability or the results from the use of Products in combination with any electrical or electronic components, circuits, system assemblies or any other materials or substances or environments. Any advice, recommendations or information given orally or in writing, are not to be construed as an amendment or addition to the above warranty. See http://www.omron.com/global/ or contact your Omron representative for published information. Limitation on Liability; Etc. OMRON COMPANIES SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, NEGLIGENCE OR STRICT LIABILITY. Further, in no event shall liability of Omron Companies exceed the individual price of the Product on which liability is asserted. Suitability of Use. Omron Companies shall not be responsible for conformity with any standards, codes or regulations which apply to the combination of the Product in the Buyer’s application or use of the Product. At Buyer’s request, Omron will provide applicable third party certification documents identifying ratings and limitations of use which apply to the Product. This information by itself is not sufficient for a complete determination of the suitability of the Product in combination with the end product, machine, system, or other application or use. Buyer shall be solely responsible for determining appropriateness of the particular Product with respect to Buyer’s application, product or system. Buyer shall take application responsibility in all cases. NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY OR IN LARGE QUANTITIES WITHOUT ENSURING THAT THE SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM. Programmable Products. Omron Companies shall not be responsible for the user’s programming of a programmable Product, or any consequence thereof. Performance Data. Data presented in Omron Company websites, catalogs and other materials is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the result of Omron’s test conditions, and the user must correlate it to actual application requirements. Actual performance is subject to the Omron’s Warranty and Limitations of Liability. Change in Specifications. Product specifications and accessories may be changed at any time based on improvements and other reasons. It is our practice to change part numbers when published ratings or features are changed, or when significant construction changes are made. However, some specifications of the Product may be changed without any notice. When in doubt, special part numbers may be assigned to fix or establish key specifications for your application. Please consult with your Omron’s representative at any time to confirm actual specifications of purchased Product. Errors and Omissions. Information presented by Omron Companies has been checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors or omissions. 2015.3 In the interest of product improvement, specifications are subject to change without notice. OMRON Corporation Industrial Automation Company http://www.ia.omron.com/ (c)Copyright OMRON Corporation 2015 All Right Reserved.