PSP-500-P 500W with PFC and Parallel Function series Features : Universal AC input / Full range Built-in active PFC function, PF>0.95 Protections:Short circuit/Over load/Over voltage/Over temperature Foced air cooling by built-in DC fan Current sharing up to 2000W(3+1) With power good and fail signal output Built-in remote ON-OFF control Built-in remote sense function 3 years warranty SPECIFICATION MODEL OUTPUT PSP-500-5P PSP-500-12P PSP-500-13.5P PSP-500-15P PSP-500-24P PSP-500-27P DC VOLTAGE 5V 12V 13.5V 15V 24V 27V 48V RATED CURRENT 80A 41.5A 37A 33A 20.8A 18.5A 10.5A CURRENT RANGE 0 ~ 80A 0 ~ 41.5A 0 ~ 37A 0 ~ 33A 0 ~ 20.8A 0 ~ 18.5A 0 ~ 10.5A RATED POWER 400W 498W 499.5W 495W 499.2W 499.5W 504W RIPPLE & NOISE (max.) Note.2 100mVp-p 150mVp-p 150mVp-p 150mVp-p 150mVp-p 150mVp-p 200mVp-p VOLTAGE ADJ. RANGE 10 ~ 13.2V 1.0% 12 ~ 15V 1.0% 13.5 ~ 18V 1.0% 20 ~ 26.4V 1.0% 24 ~ 30V 1.0% 41 ~ 56V 1.0% VOLTAGE TOLERANCE Note.3 INPUT LINE REGULATION 0.5% 0.3% 0.3% 0.3% 0.2% 0.2% 0.2% LOAD REGULATION 2.0% 0.5% 0.5% 0.5% 0.5% 0.5% 0.5% SETUP, RISE, HOLD TIME 1500ms, 50ms, 15ms at full load VOLTAGE RANGE 90 ~ 264VAC FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR 0.95/230VAC EFFICIENCY (Typ.) 76% AC CURRENT INRUSH CURRENT (max.) 7A/115AVC 20A/115VAC 127 ~ 370VDC 0.98/100VAC at full load 82% 82% 82% 84% 84% <1mA / 240VAC OVER LOAD 110 ~ 125% rated output power Protection type : Constant current limiting, recovers automatically after fault condition is removed OVER TEMPERATURE REMOTE CONTROL WORKING TEMP. WORKING HUMIDITY ENVIRONMENT STORAGE TEMP., HUMIDITY TEMP. COEFFICIENT VIBRATION SAFETY STANDARDS WITHSTAND VOLTAGE 86% 3.5A/230VAC 40A/230VAC LEAKAGE CURRENT PROTECTION OVER VOLTAGE FUNCTION 4.75 ~ 5.5V 2.0% PSP-500-48P 5.75 ~ 6.75V 13.8 ~ 16.2V 15.5 ~ 18.2V 18 ~ 21V 27.6 ~ 32.4V 31 ~ 36.5V 57.6 ~ 67.2V Protection type : Shut down o/p voltage, re-power on to recover RTH2 95 Detect on heatsink of Q1,Q7 power transistor & L3 output choke Protection type : Shut down o/p voltage, recovers automatically after temperature goes down RC+/RC-: 0 ~ 0.8V=power on ; 4 ~ 10V=power off -10 ~ +60 (Refer to output load derating curve) sink current <4 ~ 10mA 20 ~ 90% RH with 30CFM forced air non-condensing -20 ~ +85 0.03%/ , 10 ~ 95% RH (0 ~ 50 10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes UL1950, TUV EN60950 Approved I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC SAFETY & ISOLATION RESISTANCE EMI CONDUCTION & RADIATION Compliance to EN55022 (CISPR22) Class B EMC (Note 4) OTHERS NOTE HARMONIC CURRENT Compliance to EN61000-3-2,-3 EMS IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024, Light industry level, criteria A MTBF 130.1K hrs min. MIL-HDBK-217F (25 250*123*50mm (L*W*H) 1.3Kg; 6pcs/7.8Kg/1.45CUFT DIMENSION PACKING ) 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. File Name:PSP-500-P-SPEC 2004-02-04 PSP-500-P 500W with PFC and Parallel Function Mechanical Specification series Unit:mm 250 Air flow direction I/P 1 113 8 123 2 3 12 9.5 1 CN1 2 1 CN2 6 SVR1 Vo ADJ. 2 5 8 5 7 SVR2 Io ADJ. FS1 3 10A/250V 9.5 88 4 I/P 87 5 50 6- 3. 153 AC Input Terminal Pin. No. Assignment Pin No. 1 2 3 Connector Pin. No. Assignment (CN1) : JST B2B-XH or equivalent Assignment AC/L AC/N FG Pin No. 1 2 Mating Housing Terminal JST XHP or equivalent JST SXH-001T-P0.6 or equivalent Connector Pin. No. Assignment (CN2) : JST B7B-XH or equivalent DC Output Terminal Pin. No Assignment Pin No. 1~3 4~6 Assignment GND +12V Assignment Pin No. P(Current share) 1 +S 2 -S 3 GND 4 Assignment DC OUTPUT +V DC OUTPUT -V Derating Curve Mating Housing Terminal Assignment Pin No. Power fail signal 5 JST SXH-001T-P0.6 JST XHP RC+ 6 or equivalent or equivalent RC7 Output Derating VS Input Voltage 12 ~ 48V 100 100 90 80 80 70 5V With 30CFM forced air LOAD(%) LOAD (%) 60 40 20 -10 0 10 20 30 40 AMBIENT TEMPERATURE ( 50 ) 60 60 50 40 90 115 135 176 230 264 INPUT VOLTAGE (V) 60Hz File Name:PSP-500-P-SPEC 2004-02-04