● ● ● ● Features LED DRIVER ● ● ● Constant Current Operation Suitable for High Brightness LED Products Built-In Active PFC Function Overvoltage-, Short Circuit- and Overtemperature Protection Built-In 3 in 1 Dimming IP67 Rated Class 2 Power Unit UL1310 LIGHTLINE AC/DC-Converter with 5 year Warranty Selection Guide Part Number Output Voltage (VDC) Rated Power (W) Rated Current (mA) Output Voltage Range (V) Efficiency RACD45-700A 57 40 70 - 700 40 - 57 87% RACD45-1050A 48 48 105 - 1050 33 - 48 87% RACD45-1250A 36 45 125 - 1250 24 - 36 86% RACD45-1850A 24 45 185 - 1850 15 - 24 85% (typ.) 45 Watt PFC Single Output Specifications (measured at 230VAC and 25°C ambient temperature) Input Voltage Range Input Frequency Range Power Factor (Full Load) L-48 REV: 0/2015 RoHS 2011/65/EU 6/6 E340696 EN 61347-1 Certified EN 61347-2-13 Certified UL8750 Certified RACD45-A Derating-Graph (Ambient Temperature) Load 100% 90% 75% 60% 40% 230VAC only 90-305 VAC 47-63Hz 120VAC >0.98 240VAC >0.93 277VAC >0.90 THD Full Load, 115VAC 13% max. Full Load, 230VAC 19% max. DC Dimming Open = 100% DC 1-10V PWM Dimming Open = 100% Duty 10% - 100% Freq. 500Hz - 3000Hz Voltage Hi=10V, Low=0V Resistance Dimming 10K - 100K Ω Current Accuracy ±5% AC Input Current 100-240VAC 0.6A 277VAC 0.25A Inrush Current (Cold Start) 240VAC 70A Leakage Current <0.5mA / 240VAC Start-up Time (at Full Load) <2sec Isolation Voltage 3.75kVAC / 1 minute Short Circuit Protection Hiccup Over Voltage Protection 24V 26.4 - 31.2V 36V 39.6 - 46.8V 48V 52.8 - 62.4 V 57V 62.7 - 70V Over Temperature Protection Latch Mode 105 ± 10°C Vibration 10-500Hz, 2G, 60Min. along X, Y and Z Storage Humidity 10% - 90% RH Operating Humidity 20% - 90% RH Non-Condensing Weight 420g Operating Temperature -30°C to +50°C Storage Temperature -40°C to +60°C Ripple & Noise 24V 200mV (at 20MHz bandwith using 0.1uF & 47uF capacitor) all others 250mV IP Rating IP67 Isolation Resistance 100MΩ / 500VDC at 25°C Dimension (L*W*H) 179*45.1*32.5mm continued on next page 20% -30 0 20 50 65 Ambient Temperature (°C) Note: All LED Drivers may not be used without a load. They must be switched on the primary side only. Noncompliance may damage the LED or reduce its lifetime. Refer to Application Notes www.recom-power.com RACD45-A Series LIGHTLINE AC/DC-Converter Specifications (measured at 230VAC and 25°C ambient temperature) Safety Standards LED Lighting Safety LED Lighting Safety (Canada) Class 2 Power Supply Safety Extra Low-Voltage Class 2 Output LED equipment for lighting application Design Lifetime MTBF (+25°C) Report: E340696 Report: E340696 Report: E340696 Report: E340696 Report: E340696 UL8750 cUL8750 UL1310 CSA C22.2 No. 223-M91 CSA C22.2 No. 250.13-12 EN61347-1 EN61347-2-13 EN61000-3-2 Class C EN61000-3-3 EN61000-4-2,3,4,5,6,8,11 EN61547 EN55015 FCC15 70 x 10³ hours max. 200 x 10³ hours min. using MIL-HDBK 217F 3 in 1 Dimming Control (DC / PWM / Resistance) 10K-100K Resistor Dimmable (Typical): Resistor Single-Driver Multi-Driver Iout (%) 10K 10K/N 10% 20K 20K/N 20% 30K 30K/N 30% 40K 40K/N 40% 50K 50K/N 50% 60K 60K/N 60% 70K 70K/N 70% 80K 80K/N 80% 90K 90K/N 90% 100K 100K/N 100% The length of extended wire for DIM+/- shall not exceed 20 meters. (wire ≤ 20m) N = The number of dimmer drivers should not exceed 15. (N ≤ 15mS) DC: 1-10V Dimmable (Typical) Maximum Number of LED drivers per circuit breakers 80 60 Condition 40 Circuit Breaker 20 0 0 2 4 6 8 10 115VAC, 1Ohm 90° phase angle Control Voltage (V) Circuit Breaker Current Typ 10A 16A 20A 25A C 16 28 31 43 B 17 28 33 41 C 24 39 47 57 B 20 32 38 47 C 28 44 54 66 RACD45-A Output Current (%) 100 DC: 10V / PWM Dimmable (Typical) Output Current (%) 100 230VAC, 1Ohm 90° phase angle 80 60 40 20 0 0 20 40 60 80 277VAC, 1Ohm 90° phase angle 100 Duty Cycle (%) Package Style & Pinning AC IN AC N (Blue) AC L (Brown) 170±15 Tc 35.7 DC OUT +DIM 164 fixing center 8 6 AC Side V+ (Red) V- (Black) fixing Dim+ (Blue) center Dim- (White) 38 13 32.5 8 160±15 6 3.5 Note: Dim- and V- are internally connected TOP 14 10 6 13 10 BOTTOM 0.8 DC Side 8 170±15 45.1 8 0.8 160±15 0.8 23 The product information and specifications are subject to change without prior notice. RECOM products are not authorized for use in safety-critical applications (such as life support) without RECOM’s explicit written consent. A safety-critical application is defined as an application where a failure of a RECOM product may reasonably be expected to endanger or cause loss of life, inflict bodily harm or damage property. The buyer shall indemnify and hold harmless RECOM, its affiliated companies and its representatives against any damage claims in connection with the unauthorized use of RECOM products in such safety-critical applications. www.recom-power.com REV: 0/2015 L-49