FAN4800AS/CS/01S/2S PFC/PWM Controller Combination Features Description Pin-to-Pin Compatible with ML4800 and FAN4800 and CM6800 and CM6800A PWM Configurable for Current Mode or Feedforward Voltage-Mode Operation Internally Synchronized Leading-Edge PFC and Trailing-Edge PWM in One IC The highly integrated FAN4800AS/CS/01S/02S parts are specially designed for power supplies that consist of boost PFC and PWM. They require very few external components to achieve versatile protections / compensation. They are available in 16-pin DIP and SOP packages. Low Operating Current Innovative Switching-Charge Multiplier Divider Average-Current Mode for Input-Current Shaping PFC Over-Voltage and Under-Voltage Protections PFC Feedback Open-Loop Protection Cycle-by-Cycle Current Limiting for PFC/PWM Power-on Sequence Control and Soft-Start Brownout Protection Interleaved PFC/PWM Switching Improved Efficiency at Light Load fRTCT=4•fPFC=4•fPWM for FAN4800AS/01S fRTCT=4•fPFC=2•fPWM for FAN4800CS/02S The PWM can be used in either current or voltage mode. In voltage mode, feed-forward from the PFC output bus can reduce the secondary output ripple. Compared with older productions, ML4800 and FAN4800, FAN4800AS/CS/01S/02S have lower operation current that saves power consumption in external devices. FAN4800AS/CS/01S/02S have accurate 49.9% maximum duty of PWM that makes the hold-up time longer. Brownout protection and PFC softstart functions available in this series are not available in ML4800 and FAN4800. To evaluate FAN4800AS/CS/01S/02S for replacing existing FAN4800 and ML4800 boards, five things must be completed before the fine-tuning procedure: 1. Change RAC resister from the old value to a higher resister: between 6 MΩ to 8 MΩ. 2. Change RT/CT pin from the existing values to RT=6.8kΩ and CT=1000 pF to have fPFC=64 kHz and fPWM=64 kHz. 3. The VRMS pin needs to be 1.224 V at VIN=85 VAC for universal input application from line input from 85 VAC to 270 VAC. 4. At full load, the average VVEA needs to be ~4.5 V and the ripple of VVEA needs to be less than 400 mV. 5. For the Soft-Start pin, the soft-start current has been reduced to half the FAN4800 capacitor. Applications Desktop PC Power Supply Internet Server Power Supply LCD TV, Monitor Power Supply UPS Battery Charger DC Motor Power Supply Monitor Power Supply Telecom System Power Supply Distributed Power Related Resources There are two differences from FAN4800A/C/01/02 to FAN4800AS/CS/01S/02S: 1. Under-voltage protection extended to one second. debounce 2. PWM gate clamp voltage is raised to 19 V. time is AN-8027 - FAN480X PFC+PWM Combination Controller Application © 2010 Fairchild Semiconductor Corporation FAN4800AS/CS/01S/02S • Rev. 1.0.2 www.fairchildsemi.com FAN4800AS/CS/01S/02S — PFC/PWM Controller Combination January 2014 Part Number Operating Temperature Range Package FAN4800ASNY -40°C to +105°C 16-Pin Dual Inline Package (DIP) FAN4800ASMY -40°C to +105°C 16-Pin Small Outline Package (SOP) FAN4800CSNY -40°C to +105°C 16-Pin Dual Inline Package (DIP) FAN4800CSMY -40°C to +105°C 16-Pin Small Outline Package (SOP) FAN4801SNY -40°C to +105°C 16-Pin Dual Inline Package (DIP) FAN4801SMY -40°C to +105°C 16-Pin Small Outline Package (SOP) FAN4802SNY -40°C to +105°C 16-Pin Dual Inline Package (DIP) FAN4802SMY -40°C to +105°C 16-Pin Small Outline Package (SOP) Packing Method Tube Tape & Reel Tube Tape & Reel Tube Tape & Reel Tube Tape & Reel Application Diagram Figure 1. © 2010 Fairchild Semiconductor Corporation FAN4800AS/CS/01S/02S • Rev. 1.0.2 Typical Application, Current Mode www.fairchildsemi.com 2 FAN4800AS/CS/01S/02S — PFC/PWM Controller Combination Ordering Information FAN4800AS/CS/01S/02S — PFC/PWM Controller Combination Application Diagram IEA VEA IAC FBPFC VREF ISENSE VRMS VDD SS OPFC FBPWM VREF VDD OPWM RT/CT GND RAMP ILIMIT VREF Figure 2. © 2010 Fairchild Semiconductor Corporation FAN4800AS/CS/01S/02S • Rev. 1.0.2 Typical Application, Voltage Mode www.fairchildsemi.com 3 VEA IEA 16 VDD 1 7.5V REFERENCE PFC UVP VDD 27V/28V VDD OVP 0.3V Low Power Detect Comparator gmv FBPFC 15 2.5V/2.75V 2.5V S PFC OVP -1.15V Rmul gmi R 2 CLR 14 Q Q OPFC 12 S SET CLR Q VGATE-CLAMP Q 1.05V/1.9V VRMS AC UVP Gain Modulator VRMS 4 SET PFC ILIMIT R IAC 13 VREF 0.5V Rmul ISENSE 3 RT/CT 7 OSCILLATOR 300 RAMP DUTY CYCLE LIMIT 8 1.5V OPWM S FBPWM 1.15V/2.4V FBPFC 6 VDD 10µA R SET CLR Q 11 Q VGATE-CLAMP VIN OK 300 SS 5 1V VREF ILIMIT 9 GND 10 VDD Figure 3. VEA FAN4800AS/CS Function Block Diagram IEA 16 UVLO VDD 1 7.5V REFERENCE PFC UVP VDD 27V/28V VDD OVP 0.3V gmv FBPFC 15 Low Power Detect Comparator IAC 2.5V/2.75V Range 2 VRMS 4 gmi S PFC OVP -1.15V Rmul 2.5V 13 VREF 0.5V R SET CLR 14 Q Q OPFC 12 PFC ILIMIT S R SET CLR Q VGATE-CLAMP Q 1.05V/1.9V VRMS AC UVP Gain Modulator Rmul ISENSE 3 RT/CT 7 OSCILLATOR 300 RAMP DUTY CYCLE LIMIT 8 1.5V OPWM S FBPWM 1.15V/2.4V FBPFC 6 VDD 10µA R SS 5 CLR Q 11 Q VGATE-CLAMP VIN OK 300 SET 1V VREF ILIMIT 9 GND 10 VDD Figure 4. © 2010 Fairchild Semiconductor Corporation FAN4800AS/CS/01S/02S • Rev. 1.0.2 UVLO FAN4801S/02S Function Block Diagram www.fairchildsemi.com 4 FAN4800AS/CS/01S/02S — PFC/PWM Controller Combination Block Diagram F – Fairchild Logo Z – Plant Code X – 1-Digit Year Code YY – 2-Digit Week Code TT – 2-Digit Die-Run Code T – Package Type (N:DIP) P – Y: Green Package M – Manufacture Flow Code Figure 5. DIP Top Mark F – Fairchild Logo Z – Plant Code X – 1-Digit Year Code Y – 1-Digit Week Code TT – 2-Digit Die-Run Code T – Package Type (M:SOP) P – Y: Green Package M – Manufacture Flow Code Figure 6. © 2010 Fairchild Semiconductor Corporation FAN4800AS/CS/01S/02S • Rev. 1.0.2 SOP Top Mark www.fairchildsemi.com 5 FAN4800AS/CS/01S/02S — PFC/PWM Controller Combination Marking Information Figure 7. Pin Configuration (Top View) Pin Definitions Pin # Name Description 1 IEA Output of PFC Current Amplifier. The signal from this pin is compared with an internal sawtooth to determine the pulse width for PFC gate drive. 2 IAC Input AC Current. For normal operation, this input provides current reference for the multiplier. The suggested maximum IAC is 100 µA. 3 ISENSE 4 VRMS 5 SS 6 FBPWM 7 RT/CT Oscillator RC Timing Connection. Oscillator timing node; timing set by RT and CT. 8 RAMP PWM RAMP Input. In current mode, this pin functions as the current-sense input; when in voltage mode, it is the feedforward sense input from PFC output 380 V (feedforward ramp). Peak Current Limit Setting for PWM. The peak current limits setting for PWM. PFC Current Sense. The non-inverting input of the PFC current amplifier and the output of multiplier and PFC ILIMIT comparator. Line-Voltage Detection. The pin is used for the PFC multiplier. PWM Soft-Start. During startup, the SS pin charges an external capacitor with a 10 µA constant current source. The voltage on FBPWM is clamped by SS during startup. If a protection condition occurs and/or PWM is disabled, the SS pin is quickly discharged. PWM Feedback Input. The control input for voltage-loop feedback of PWM stage. 9 ILIMIT 10 GND 11 OPWM PWM Gate Drive. The totem-pole output drive for PWM MOSFET. This pin is internally clamped under 19 V to protect the MOSFET. 12 OPFC PFC Gate Drive. The totem-pole output drive for PFC MOSFET. This pin is internally clamped under 15 V to protect the MOSFET. 13 VDD Supply. The power supply pin. The threshold voltages for startup and turn-off are 11 V and 9.3 V, respectively. The operating current is lower than 10 mA. 14 VREF Reference Voltage. Buffered output for the internal 7.5 V reference. 15 FBPFC 16 VEA Ground. Voltage Feedback Input for PFC. The feedback input for PFC voltage loop. The inverting input of PFC error amplifier. This pin is connected to the PFC output through a divider network. Output of PFC Voltage Amplifier. The error amplifier output for PFC voltage feedback loop. A compensation network is connected between this pin and ground. © 2010 Fairchild Semiconductor Corporation FAN4800AS/CS/01S/02S • Rev. 1.0.2 www.fairchildsemi.com 6 FAN4800AS/CS/01S/02S — PFC/PWM Controller Combination Pin Configuration Stresses exceeding the absolute maximum ratings may damage the device. The device may not function or be operable above the recommended operating conditions and stressing the parts to these levels is not recommended. In addition, extended exposure to stresses above the recommended operating conditions may affect device reliability. The absolute maximum ratings are stress ratings only. Symbol Parameter Min. Max. Unit 30 V VDD DC Supply Voltage VH SS, FBPWM, RAMP, OPWM, OPFC, VREF -0.3 30.0 V VL IAC, VRMS, RT/CT, ILIMIT, FBPFC, VEA -0.3 7.0 V 0 VVREF+0.3 V -5.0 0.7 V 1 mA VIEA IEA VN ISENSE IAC Input AC Current IREF VREF Output Current 5 mA IPFC-OUT Peak PFC OUT Current, Source or Sink 0.5 A IPWM-OUT Peak PWM OUT Current, Source or Sink 0.5 A PD Power Dissipation TA < 50°C 800 mW ΘJA Thermal Resistance (Junction-to-Air) ΘJC Thermal Resistance (Junction-to-Case) TJ DIP 80.80 SOP 104.10 DIP 35.38 SOP 40.41 °C/W °C/W Operating Junction Temperature -40 +125 °C TSTG Storage Temperature Range -55 +150 °C TL Lead Temperature(Soldering) +260 °C ESD Electrostatic Discharge Capability Human Body Model 5.0 Charged Device Model 1.5 kV Notes: 1. All voltage values, except differential voltage, are given with respect to GND pin. 2. Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Recommended Operating Conditions The Recommended Operating Conditions table defines the conditions for actual device operation. Recommended operating conditions are specified to ensure optimal performance to the datasheet specifications. Fairchild does not recommend exceeding them or designing to Absolute Maximum Ratings. Symbol TA Parameter Min. Operating Ambient Temperature © 2010 Fairchild Semiconductor Corporation FAN4800AS/CS/01S/02S • Rev. 1.0.2 -40 Typ. Max. Unit +105 °C www.fairchildsemi.com 7 FAN4800AS/CS/01S/02S — PFC/PWM Controller Combination Absolute Maximum Ratings Unless otherwise noted, VDD=15 V, TA= 25°C, TA=TJ, RT=6.8 kΩ, and CT=1000 pF. Symbol Parameter Conditions Min. Typ. Max. Unit 26 V 30 80 µA VDD Section VDD-OP Continuously Operating Voltage IDD ST Startup Current VDD=VTH-ON-0.1 V; OPFC OPWM Open IDD-OP Operating Current VDD=13 V; OPFC OPWM Open 2.0 2.6 5.0 mA VTH-ON Turn-on Threshold Voltage 10 11 12 V Hysteresis 1.3 1.9 V VDD OVP 27 29 V ΔVTH VDD-OVP ΔVDD-OVP VDD OVP Hysteresis 28 1 V Oscillator fOSC-RT/CT fOSC RT/CT Frequency RT=6.8 kΩ, CT=1000 pF 240 256 268 kHz PFC & PWM Frequency RT=6.8 kΩ, CT=1000 pF 60 64 67 kHz 120 128 134 PWM Frequency fDV fDT fTV fRV Voltage Stability(3) (3) Temperature Stability (3) Total Variation (PFC & PWM) 11 V ≦ VDD ≦ 22 V 2 % -40°C ~ +105°C 2 % 70 kHz 6.5 15.0 mA 50 75 kHz Line, Temperature Ramp Voltage Valley to Peak IOSC-DIS Discharge Current VRAMP=0V, VRT/CT=2.5 V fRANGE Frequency Range tPFC-DEAD 58 2.8 V PFC Dead Time RT=6.8 kΩ, CT=1000 pF 400 600 800 ns Reference Voltage IREF=0 mA, CREF=0.1 µF 7.4 7.5 7.6 V ΔVVREF1 Load Regulation of Reference Voltage CREF=0.1 µF, IREF=0 mA to 3.5 mA VVDD=14 V, Rise/Fall Time > 20 µs 30 50 mV ΔVVREF2 Line Regulation of Reference Voltage CREF=0.1 µF, VVDD=11 V to 22 V 25 mV VREF VVREF (3) ΔVVREF-DT Temperature Stability -40°C ~ +105°C ΔVVREF-TV Total Variation(3) Line, Load, Temp ΔVVREF-LS IREF-MAX (3) 0.5 % 7.35 0.4 7.65 V 25 mV Long-Term Stability TJ=125°C, 0 ~ 1000 HRs 5 Maximum Current VVREF > 7.35 V 5 mA PFC OVP Comparator VPFC-OVP ΔVPFC-OVP Over-Voltage Protection 2.70 2.75 2.80 V PFC OVP Hysteresis 200 250 300 mV 0.2 0.3 0.4 V Voltage Level on FBPFC to Enable OPWM During Startup 2.3 2.4 2.5 V Hysteresis 1.15 1.25 1.35 V Low-Power Detect Comparator VVEAOFF VEA Voltage OFF OPFC VIN OK Comparator VRD-FBPFC ΔVRD-FBPFC Continued on the following page… © 2010 Fairchild Semiconductor Corporation FAN4800AS/CS/01S/02S • Rev. 1.0.2 www.fairchildsemi.com 8 FAN4800AS/CS/01S/02S — PFC/PWM Controller Combination Electrical Characteristics Unless otherwise noted, VDD=15 V, TA= 25°C, TA=TJ, RT=6.8 kΩ, and CT=1000 pF. Symbol Parameter Conditions Min. Typ. Max. 2.55 Unit Voltage Error Amplifier VREF Reference Voltage 2.45 2.50 AV Open-Loop Gain(3) 35 42 Gmv Transconductance VNONINV=VINV, VVEA=3.75 V 50 70 40 IFBPFC-L Maximum Source Current VFBPFC=2 V, VVEA=1.5 V IFBPFC-H Maximum Sink Current VFBPFC=3 V, VVEA=6 V IBS 90 umho -40 µA 1 µA 0.1 0.4 V 88 100 umho 10 mV 7.4 8.0 V 0.1 0.4 V -35 µA 50 -50 Input Bias Current -1 VVEA-H Output High Voltage on VVEA 5.8 VVEA-L Output Low Voltage on VVEA V dB µA 6.0 V Current Error Amplifier GmI Transconductance VNONINV=VINV, VIEA=3.75 V 78 VOFFSET Input Offset Voltage VVEA=0 V, IAC Open -10 VIEA-H Output High Voltage VIEA-L Output Low Voltage 6.8 IL Source Current VISENSE=-0.6 V, VIEA=1.5 V IH Sink Current VISENSE=+0.6 V, VIEA=4.0 V AI(3) 35 50 -50 Open-Loop Gain 40 µA 50 dB TriFault Detect™ tFBPFC_OPEN VPFC-UVP Time to FBPFC Open VFBPFC=VPFC-UVP to FBPFC OPEN, 470 pF from FBPFC to GND PFC Feedback Under-Voltage Protection 0.4 2 4 ms 0.5 0.6 V 100 µA Gain Modulator IAC GAIN BW VO(gm) Input for AC Current(3) GAIN Modulator(4) Bandwidth(3) Multiplier Linear Range 0 IAC=17.67µA, VRMS=1.080V VFBPFC=2.25V 7.500 9.000 10.500 IAC=20.00 µA, VRMS=1.224 V VFBPFC=2.25 V 6.367 7.004 7.704 IAC=25.69 µA, VRMS=1.585 V VFBPFC=2.25 V 3.801 4.182 4.600 IAC=51.62 µA, VRMS=3.169 V VFBPFC=2.25 V 0.950 1.045 1.149 IAC=62.23 µA, VRMS=3.803 V VFBPFC=2.25 V 0.660 0.726 0.798 IAC=40 µA Output Voltage=5.7 kΩ × (ISENSE- IAC=20 µA, VRMS=1.224 V IOFFSET) VFBPFC=2.25 V 2 kHz 0.710 0.798 0.885 V -1.35 -1.20 -1.05 V PFC ILIMIT Comparator VPFC-ILIMIT ΔVPK Peak Current Limit Threshold Voltage, Cycle-by-Cycle Limit PFC ILIMIT-Gain Modulator Output IAC=17.67 µA, VRMS=1.08 V VFBPFC=2.25 V 200 mV Continued on the following page… © 2010 Fairchild Semiconductor Corporation FAN4800AS/CS/01S/02S • Rev. 1.0.2 www.fairchildsemi.com 9 FAN4800AS/CS/01S/02S — PFC/PWM Controller Combination Electrical Characteristics (Continued) Unless otherwise noted, VDD=15 V, TA= 25°C, TA=TJ, RT=6.8 kΩ, and CT=1000 pF. Symbol Parameter Conditions Min. Typ. 13 15 Max. Unit PFC Output Driver VGATE-CLAMP Gate Output Clamping Voltage VDD=22 V VGATE-L Gate Low Voltage VDD=15 V, IO=100 mA 17 V 1.5 V VGATE-H Gate High Voltage VDD=13 V, IO=100 mA 8 tR Gate Rising Time VDD=15 V, CL=4. 7nF, O/P= 2 V to 9 V 40 70 120 ns tF Gate Falling Time VDD=15 V; CL=4.7 nF, O/P= 9 V to 2 V 40 60 110 ns DPFC-MAX Maximum Duty Cycle VIEA<1.2 V 94 97 DPFC-MIN Minimum Duty Cycle VIEA>4.5 V VRMS-UVL VRMS Threshold Low When VRMS=1.05 V at 75 VRMS 1.03 VRMS-UVH VRMS Threshold High When VRMS=1.9 V at 85•1.414 V % 0 % 1.05 1.08 V 1.88 1.90 1.94 V Hysteresis 750 850 950 mV Under Voltage Protection Debounce Time 850 1000 1150 ms 9.5 10.0 10.5 Brownout VRMS-UVP tUVP Soft Start VSS-MAX Maximum Voltage ISS Soft-Start Current VDD=15 V 10 V µA PWM ILIMIT Comparator VPWM-ILIMIT Threshold Voltage tPD Propagation Delay to Output tPWM-BNK Leading-Edge Blanking Time 0.95 1.00 1.05 250 V ns 170 250 350 ns Range (FAN4801S/02S) VVRMS-L RMS AC Voltage Low When VVRMS=1.95 V at 132 VRMS 1.90 1.95 2.00 V VVRMS-H RMS AC Voltage High When VVRMS=2.45 V at 150 VRMS When VVEA=1.95 V at 30% Loading When VVEA=2.45 V at 40% Loading 2.40 2.45 2.50 V 1.90 1.95 2.00 V 2.40 2.45 2.50 V 18 20 22 µA 18 19 20 V 1.5 V VVEA-L VEA LOW VVEA-H VEA HIGH ITC Source Current from FBPFC PWM Output Driver VGATE-CLAMP Gate Output Clamping Voltage VDD=22 V VGATE-L Gate Low Voltage VDD=15 V, IO=100 mA VGATE-H Gate High Voltage VDD=13 V, IO=100 mA 8 tR Gate Rising Time VDD=15 V, CL=4.7 nF 30 60 120 ns tF Gate Falling Time VDD=15 V, CL=4.7 nF 30 50 110 ns Maximum Duty Cycle 49.0 49.5 50.0 % PWM Comparator Level Shift 1.3 1.5 1.8 V DPWM-MAX VPWM-LS V Notes: 3. This parameter, although guaranteed by design, is not 100% production tested. 4. This GAIN is the maximum gain of modulation with a given VRMS voltage when VVEA is saturated to HIGH. © 2010 Fairchild Semiconductor Corporation FAN4800AS/CS/01S/02S • Rev. 1.0.2 www.fairchildsemi.com 10 FAN4800AS/CS/01S/02S — PFC/PWM Controller Combination Electrical Characteristics (Continued) 20.0 28.04 18.0 28.02 16.0 28.00 VDD-OVP(V) IDD-ST(uA) 14.0 12.0 10.0 8.0 6.0 27.94 27.92 27.90 2.0 27.88 27.86 -40℃ -25℃ -10℃ 5℃ Figure 8. 20℃ 35℃ 50℃ 65℃ 80℃ 95℃ -40℃ -25℃ -10℃ 110℃ 125℃ IDD-ST vs. Temperature 5℃ Figure 9. 65.0 7.520 64.9 7.515 64.8 7.510 64.7 VVREF(V) FOSC(kHz) 27.96 4.0 0.0 64.6 64.5 20℃ 35℃ 50℃ 65℃ 80℃ 95℃ 110℃ 125℃ VDD-OVP vs. Temperature 7.505 7.500 7.495 7.490 64.4 7.485 64.3 7.480 64.2 7.475 -40℃ -25℃ -10℃ 5℃ Figure 10. 20℃ 35℃ 50℃ 65℃ 80℃ 95℃ -40℃ -25℃ -10℃ 110℃ 125℃ fOSC vs. Temperature 5℃ Figure 11. 2.742 2.502 2.740 2.500 20℃ 35℃ 50℃ 65℃ 80℃ 95℃ 110℃ 125℃ VVREF vs. Temperature 2.498 2.738 VREF(V) VPFC-OVP(V) 27.98 2.736 2.734 2.496 2.494 2.492 2.732 2.490 2.730 2.488 -40℃ -25℃ -10℃ 5℃ Figure 12. 20℃ 35℃ 50℃ 65℃ 80℃ 95℃ 110℃ 125℃ -40℃ -25℃ -10℃ VPFC-OVP vs. Temperature 5℃ Figure 13. 20℃ 35℃ 50℃ 65℃ 80℃ 95℃ 110℃ 125℃ VREF vs. Temperature 94 74 92 90 GmI(umho) GmV(umho) 73 73 72 88 86 84 82 72 80 71 78 -40℃ -25℃ -10℃ 5℃ 20℃ Figure 14. 35℃ 50℃ 65℃ 80℃ 95℃ -40℃ 110℃ 125℃ GmV vs. Temperature -10℃ 5℃ 20℃ Figure 15. -1.177 35℃ 50℃ 65℃ 80℃ 95℃ 110℃ 125℃ GmI vs. Temperature 1.010 1.009 VPWM-ILIMIT(V) -1.178 VPFC-ILIMIT(V) -25℃ -1.179 -1.180 -1.181 -1.182 1.008 1.007 1.006 1.005 1.004 1.003 1.002 -1.183 -40 -25 -10 Figure 16. 5 20 35 50 65 80 95 110 125 VPFC-ILIMIT vs. Temperature © 2010 Fairchild Semiconductor Corporation FAN4800AS/CS/01S/02S • Rev. 1.0.2 -40℃ -25℃ -10℃ Figure 17. 5℃ 20℃ 35℃ 50℃ 65℃ 80℃ 95℃ 110℃ 125℃ VPWM-ILIMIT vs. Temperature www.fairchildsemi.com 11 FAN4800AS/CS/01S/02S — PFC/PWM Controller Combination Typical Characteristics 1.048 867.5 1.047 867.0 866.5 △VRMS-UVP(mV) VRMS-UVP(V) 1.046 1.045 1.044 1.043 1.042 1.041 1.040 1.038 865.0 864.5 864.0 863.5 862.0 -40℃ -25℃ -10℃ 5℃ Figure 18. 20℃ 35℃ 50℃ 65℃ 80℃ 95℃ -40℃ -25℃ -10℃ 110℃ 125℃ VRMS-UVP vs. Temperature 14.7 19.00 14.6 18.95 14.5 14.4 14.3 14.2 14.1 14.0 35℃ 50℃ 65℃ 80℃ 95℃ 110℃ 125℃ ΔVRMS-UVP vs. Temperature 18.90 18.85 18.80 18.75 18.70 18.65 18.60 18.50 -40℃ -25℃ -10℃ Figure 20. 5℃ 20℃ 35℃ 50℃ 65℃ 80℃ 95℃ -40℃ -25℃ -10℃ 110℃ 125℃ VGATE-CLAMP-PFC vs. Temperature Figure 21. 96.06 5℃ 20℃ 35℃ 50℃ 65℃ 80℃ 95℃ 110℃ 125℃ VGATE-CLAMP-PWM vs. Temperature 49.80 96.04 49.75 DPWM-MAX(%) 96.02 96.00 95.98 95.96 95.94 95.92 49.70 49.65 49.60 49.55 95.90 95.88 49.50 -40℃ -25℃ -10℃ 5℃ Figure 22. 20℃ 35℃ 50℃ 65℃ 80℃ 95℃ 110℃ 125℃ -40℃ -25℃ DPFC-MAX vs. Temperature -10℃ 5℃ Figure 23. 10.1 21.0 10.0 20.8 9.9 20℃ 35℃ 50℃ 65℃ 80℃ 95℃ 110℃ 125℃ DPWM-MAX vs. Temperature 20.6 9.8 9.7 ITC(uA) ISS(uA) 20℃ 18.55 13.9 9.6 9.5 9.4 20.4 20.2 20.0 19.8 9.3 19.6 9.2 9.1 -40℃ 5℃ Figure 19. VGATE-CLAMP-PWM(V) VGATE-CLAMP-PFC(V) 865.5 863.0 862.5 1.039 DPFC-MAX(%) 866.0 19.4 -25℃ -10℃ 5℃ Figure 24. 20℃ 35℃ 50℃ 65℃ 80℃ 95℃ 110℃ 125℃ ISS vs. Temperature © 2010 Fairchild Semiconductor Corporation FAN4800AS/CS/01S/02S • Rev. 1.0.2 -40℃ -25℃ -10℃ 5℃ Figure 25. 20℃ 35℃ 50℃ 65℃ 80℃ 95℃ 110℃ 125℃ ITC vs. Temperature www.fairchildsemi.com 12 FAN4800AS/CS/01S/02S — PFC/PWM Controller Combination Typical Characteristics The FAN4800AS/CS/01S/02S consist of an average current controlled, continuous-boost, Power Factor Correction (PFC) front-end and a synchronized Pulse Width Modulator (PWM) back-end. The PWM can be used in current or voltage mode. In voltage mode, feedforward from the PFC output bus can help improve the line regulation of PWM. In either mode, the PWM stage uses conventional trailing-edge, duty-cycle modulation. This proprietary leading / trailing edge modulation results in a higher usable PFC error amplifier bandwidth and can significantly reduce the size of the PFC DC bus capacitor. IGAINMOD = I AC × (VEA − 0.7 ) ×K (1) VRMS 2 Note that the output current of the gain modulator is limited around 159 μA and the maximum output voltage of the gain modulator is limited to 159 μA x 5.7 k=0.906 V. This 0.906 V also determines the maximum input power. However, IGAINMOD cannot be measured directly from ISENSE. ISENSE=IGAINMOD – IOFFSET and IOFFSET can only be measured when VVEA is less than 0.5 V and IGAINMOD is 0 A. Typical IOFFSET is around 31 μA ~ 48 μA. The synchronization of the PWM with the PFC simplifies the PWM compensation due to the controlled ripple on the PFC output capacitor (the PWM input capacitor). Selecting RAC for the IAC Pin The IAC pin is the input of the gain modulator and also a current mirror input that requires current input. Selecting a proper resistor, RAC, provides a good sine wave current derived from the line voltage and helps program the maximum input power and minimum input line voltage. RAC=VIN peak x 56 kΩ. For example, if the minimum line voltage is 75 VAC, the RAC=75 x 1.414 x 56 kΩ=6 MΩ. In addition to power factor correction, a number of protection features are built into this series. They include soft-start, PFC over-voltage protection, peak current limiting, brownout protection, duty cycle limiting, and under-voltage lockout (UVLO). Gain Modulator Current Amplifier Error, IEA The gain modulator is the heart of the PFC, as the circuit block controls the response of the current loop to line voltage waveform and frequency, RMS line voltage, and PFC output voltages. There are three inputs to the gain modulator: The current error amplifier’s output controls the PFC duty cycle to keep the average current through the boost inductor a linear function of the line voltage. At the inverting input to the current error amplifier, the output current of the gain modulator is summed with a current, which results in a negative voltage being impressed upon the ISENSE pin. 1. A current representing the instantaneous input voltage (amplitude and wave shape) to the PFC. The rectified AC input sine wave is converted to a proportional current via a resistor and is fed into the gain modulator at IAC. Sampling current in this way minimizes ground noise, required in high-power, switching-power conversion environments. The gain modulator responds linearly to this current. The negative voltage on ISENSE represents the sum of all currents flowing in the PFC circuit and is typically derived from a current-sense resistor in series with the negative terminal of the input bridge rectifier. 2. A voltage proportional to the long-term RMS AC line voltage, derived from the rectified line voltage after scaling and filtering. This signal is presented to the gain modulator at VRMS. The output of the gain modulator is inversely proportional to VRMS (except at unusually low values of VRMS, where special gain contouring takes over to limit power dissipation of the circuit components under brownout conditions). The inverting input of the current error amplifier is a virtual ground. Given this fact, and the arrangement of the duty cycle modulator polarities internal to the PFC, an increase in positive current from the gain modulator causes the output stage to increase its duty cycle until the voltage on ISENSE is adequately negative to cancel this increased current. Similarly, if the gain modulator’s output decreases, the output duty cycle decreases to achieve a less negative voltage on the ISENSE pin. 3. The output of the voltage error amplifier, VEA. The gain modulator responds linearly to variations in VVEA. PFC Cycle-By-Cycle Current Limiter In addition to being a part of the current feedback loop, the ISENSE pin is a direct input to the cycle-by-cycle current limiter for the PFC section. If the input voltage at this pin is less than -1.15 V, the output of the PFC is disabled until the protection flip-flop is reset by the clock pulse at the start of the next PFC power cycle. The output of the gain modulator is a current signal, in the form of a full wave rectified sinusoid at twice the line frequency. This current is applied to the virtual ground (negative) input of the current error amplifier. In this way, the gain modulator forms the reference for the current error loop and ultimately controls the instantaneous current draw of the PFC from the power line. The general form of the output of the gain modulator is: © 2010 Fairchild Semiconductor Corporation FAN4800AS/CS/01S/02S • Rev. 1.0.2 www.fairchildsemi.com 13 FAN4800AS/CS/01S/02S — PFC/PWM Controller Combination Functional Description Error Amplifier Compensation To improve power supply reliability, reduce system component count, and simplify compliance to UL1950 safety standards; the FAN4800AS/CS/01S/02S includes TriFault Detect™ technology. This feature monitors FBPFC for certain PFC fault conditions. The PWM loading of the PFC can be modeled as a negative resistor because an increase in the input voltage to the PWM causes a decrease in the input current. This response dictates the proper compensation of the two transconductance error amplifiers. Figure 26 shows the types of compensation networks most commonly used for In a feedback path failure, the output of the PFC could the voltage and current error amplifiers, along with their exceed safe operating limits. With such a failure, FBPFC respective return points. The current-loop compensation exceeds its normal operating area. Should FBPFC go too is returned to VREF to produce a soft-start characteristic low, too high, or open; TriFault Detect™ senses the error on the PFC. As the reference voltage increases from 0V, and terminates the PFC output drive. it creates a differentiated voltage on IEA, which prevents TriFault Detect is an entirely internal circuit. It requires no the PFC from immediately demanding a full duty cycle on its boost converter. Complete design is discussed in external components to serve its protective function. application note AN-6078SC. PFC Over-Voltage Protection There is an RC filter between Rsense and ISENSE pin. In the FAN4800AS/CS/01S/02S, the PFC OVP There are two reasons to add a filter at the ISENSE pin: comparator serves to protect the power circuit from being subjected to excessive voltages if the load changes 1. Protection: During startup or inrush current conditions, there is a large voltage across Rsense, the sensing suddenly. A resistor divider from the high-voltage DC resistor of the PFC boost converter. It requires the output of the PFC is fed to FBPFC. When the voltage on ISENSE filter to attenuate the energy. FBPFC exceeds 2.75 V, the PFC output driver is shut down. The PWM section continues to operate. The OVP 2. To reduce inductance, L, the boost inductor. The comparator has 250 mV of hysteresis and the PFC does ISENSE filter also can reduce the boost inductor value not restart until the voltage at FBPFC drops below 2.5 V. since the ISENSE filter behaves like an integrator before VDD OVP can also serve as a redundant PFC OVP the ISENSE pin, which is the input of the current error protection. VDD OVP threshold is 28 V with 1 V hysteresis. amplifier, IEA. The ISENSE filter is an RC filter. The resistor value of the ISENSE filter is between 100 Ω and 50 Ω because IOFFSET x Rsense is the sensing resistor of the PFC boost converter. RFILTER can generate a negative offset voltage of IEA. During the steady state, line input current x Rsense equals Selecting an RFILTER equal to 50 Ω keeps the offset of the IGAINMOD x 5.7 kΩ. IEA less than 3 mV. Design the pole of the ISENSE filter at f /6, one sixth of the PFC switching frequency, so the At full load, the average VVEA needs to around 4.5 V and PFC boost inductor can be reduced six times without ripple on the VEA pin needs to be less than 400 mV. disturbing the stability. The capacitor of the ISENSE filter, Choose the resistance of the sensing resistor: CFILTER, is approximately 100 nF. Selecting PFC Rsense RSENSE = ( 4.5 − 0.7 ) × 5.7K Ω × IAC × Gain × VIN × 2 × ( 5.6 − 0.7 ) × Line _ Input _ Power 2 (2) where 5.6 is VVEA maximum output voltage. PFC Soft-Start PFC startup is controlled by VVEA level. Before the FBPFC voltage reaches 2.4 V, the VVEA level is around 2.8 V. At 90 VAC, the PFC soft-start time is 90 ms. PFC Brownout The AC UVP comparator monitors the AC input voltage. The PFC is disabled as AC input lowers, causing VRMS to be less than 1.05 V. Figure 26. Compensation Network Connection for the Voltage and Current Error Amplifiers © 2010 Fairchild Semiconductor Corporation FAN4800AS/CS/01S/02S • Rev. 1.0.2 www.fairchildsemi.com 14 FAN4800AS/CS/01S/02S — PFC/PWM Controller Combination TriFault Detect™ Pulse Width Modulator (PWM) To improve the efficiency, the system can reduce PFC switching loss at low line and light load by reducing the PFC output voltage. The two-level PFC output of the FAN4801S/02S can be programmable. The operation of the PWM section is straightforward, but there are several points that should be noted. Foremost among these is the inherent synchronization of PWM with the PFC section of the device, from which it also derives its basic timing. The PWM is capable of current-mode or voltage-mode operation. In currentmode applications, the PWM ramp (RAMP) is usually derived directly from a current-sensing resistor or current transformer in the primary side of the output stage. It is thereby representative of the current flowing in the converter’s output stage. ILIMIT, which provides cycle-by-cycle current limiting, is typically connected to RAMP in such applications. For voltage-mode operation and certain specialized applications, RAMP can be connected to a separate RC timing network to generate a voltage ramp against which FBPWM is compared. Under these conditions, the use of voltage feedforward from the PFC bus can assist in line regulation accuracy and response. As in current-mode operation, the ILIMIT input is used for output stage over-current protection. No voltage error amplifier is included in the PWM stage, as this function is generally performed on the output side of the PWM’s isolation boundary. To facilitate the design of opto-coupler feedback circuitry, an offset has been built into the PWM’s RAMP input that allows FBPWM to command a 0% duty cycle for input voltages below typical 1.5 V. As Figure 27 shows, FAN4801S/02S detect the voltage of VEA and VRMS pins to determine if the system operates low line and light load. At the second-level PFC, there is a current of 20 µA through RF2 from the FBPFC pin. The second-level PFC output voltage can be calculated as. Output ≅ RF 1 + RF 2 × ( 2.5V − 20 μ A × RF 2 ) RF 2 (3) For example, if the second-level PFC output voltage is expected as 300 V and normal voltage is 387 V, according to the equation, RF2 is 28 kΩ RF1 is 4.3 MΩ. The programmable range of second level PFC output voltage is 340 V ~ 300 V. PWM Cycle-by-Cycle Current Limiter Figure 27. The ILIMIT pin is a direct input to the cycle-by-cycle current limiter for the PWM section. Should the input voltage at this pin exceed 1 V, the output flip-flop is reset by the clock pulse at the start of the next PWM power cycle. When the ILIMIT triggers the cycle-by-cycle bi-cycle current, it limits the PWM duty cycle mode and the power dissipation is reduced during the dead-short condition. Two-Level PFC Scheme Oscillator (RT/CT) The oscillator frequency is determined by the values of RT and CT, which determine the ramp and off-time of the oscillator output clock: VIN OK Comparator 1 fRT / CT = (4) tRT / CT + tDEAD The dead time of the oscillator is derived from the following equation: The VIN OK comparator monitors the DC output of the PFC and inhibits the PWM if the voltage on FBPFC is less than its nominal 2.4 V. Once the voltage reaches 2.4 V, which corresponds to the PFC output capacitor being charged to its rated boost voltage, soft-start begins. VREF − 1 tRT / CT = CT × RT × ln VREF − 3.8 at VREF=7.5 V and tRT/CT=CT x RT x 0.56. PWM Soft-Start (SS) (5) PWM startup is controlled by selection of the external capacitor at soft-start. A current source of 10 µA supplies the charging current for the capacitor and startup of the PWM begins at 1.5 V. The dead time of the oscillator is determined using: 2.8V × CT = 360 × CT (6) 7.78mA The dead time is so small (tRT/CT>>tDEAD) that the operating frequency can typically be approximated by: tDEAD = fRT / CT = 1 tRT / CT © 2010 Fairchild Semiconductor Corporation FAN4800AS/CS/01S/02S • Rev. 1.0.2 (7) www.fairchildsemi.com 15 FAN4800AS/CS/01S/02S — PFC/PWM Controller Combination Two-Level PFC Function Leading/Trailing Edge Modulation When the PWM section is used in current mode, RAMP is generally used as the sampling point for a voltage, representing the current in the primary of the PWM’s output transformer. The voltage is derived either from a current-sensing resistor or a current transformer. In voltage mode, RAMP is the input for a ramp voltage generated by a second set of timing components (RRAMP, CRAMP) that have a minimum value of 0V and a peak value of approximately 6 V. In voltage mode, feedforward from the PFC output bus is an excellent way to derive the timing ramp for the PWM stage. Conventional PWM techniques employ trailing-edge modulation, in which the switch turns on right after the trailing edge of the system clock. The error amplifier output is then compared with the modulating ramp up. The effective duty cycle of the trailing-edge modulation is determined during the on-time of the switch. In the case of leading-edge modulation, the switch is turned off exactly at the leading edge of the system clock. When the modulating ramp reaches the level of the error amplifier output voltage, the switch is turned on. The effective duty-cycle of the leading-edge modulation is determined during off-time of the switch. Generating VDD After turning on the FAN4800AS/CS/01S/02S at 11 V, the operating voltage can vary from 9.3 V to 28 V. The threshold voltage of the VDD OVP comparator is 28 V and its hysteresis is 1 V. When VDD reaches 28 V, OPFC is LOW and the PWM section is not disturbed. There are two ways to generate VDD: use auxiliary power supply around 15 V or use bootstrap winding to self-bias the FAN4800AS/CS/01S/02S system. The bootstrap winding can be taped from the PFC boost choke or the transformer of the DC-to-DC stage. © 2010 Fairchild Semiconductor Corporation FAN4800AS/CS/01S/02S • Rev. 1.0.2 www.fairchildsemi.com 16 FAN4800AS/CS/01S/02S — PFC/PWM Controller Combination PWM Control (RAMP) 19.69 18.67 9 16 7.11 6.10 1 8 (0.40) TOP VIEW 0.38 MIN 5.33 MAX 8.25 7.62 1.78 1.14 0.28 0.20 4.95 2.92 3.81 2.92 2.54 0.56 0.36 10.92 0.25 C SIDE VIEW NOTES: UNLESS OTHERWISE SPECIFIED A) THIS PACKAGE CONFORMS TO JEDEC MS-001 VARIATION BB B) ALL DIMENSIONS ARE IN MILLIMETERS. C) DIMENSIONS ARE EXCLUSIVE OF BURRS, MOLD FLASH, AND TIE BAR PROTRUSIONS D) CONFORMS TO ASME Y14.5M-1994 E) DRAWING FILE NAME: N16EREV2 Figure 28. 16-Pin, Dual In-Line Package (DIP), JEDEC MS-001, .300" Wide Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/. © 2010 Fairchild Semiconductor Corporation FAN4800AS/CS/01S/02S • Rev. 1.0.2 www.fairchildsemi.com 17 FAN4800AS/CS/01S/02S — PFC/PWM Controller Combination Physical Dimensions FAN4800AS/CS/01S/02S — PFC/PWM Controller Combination Physical Dimensions Figure 29. 16-Pin Small Outline Package (SOIC), JEDEC MS-012, .150", Narrow Body Package drawings are provided as a service to customers considering Fairchild components. Drawings may change in any manner without notice. Please note the revision and/or date on the drawing and contact a Fairchild Semiconductor representative to verify or obtain the most recent revision. Package specifications do not expand the terms of Fairchild’s worldwide terms and conditions, specifically the warranty therein, which covers Fairchild products. Always visit Fairchild Semiconductor’s online packaging area for the most recent package drawings: http://www.fairchildsemi.com/packaging/. © 2010 Fairchild Semiconductor Corporation FAN4800AS/CS/01S/02S • Rev. 1.0.2 www.fairchildsemi.com 18 FAN4800AS/CS/01S/02S — PFC/PWM Controller Combination © 2010 Fairchild Semiconductor Corporation FAN4800AS/CS/01S/02S • Rev. 1.0.2 www.fairchildsemi.com 19