VIRGINIA PANEL CORPORATION i2 MICRO iCON USER’S MANUAL: SECTION 2 i2 MICRO iCON RECEIVER & ITA ENGAGEMENT AND DISENGAGEMENT RECEIVER • PART # 310 130 XXX ITA • PART # 410 130 XXX ENGAGEMENT INSTRUCTIONS 1. Turn the engagement knob counter-clockwise to the open, disengaged position (Figure A). The triangle will point down. 2. Align the ITA with the receiver and push the ITA onto the receiver. There will be about a 0.25″ [6.35 mm] gap. NOTE: The i2 Micro iCon connector is polarized; the ITA will not align if it is upside down. NOTE: The i2 Micro iCon ITA can be left in this position without engaging the system. 3. Rotate the knob clockwise to engage (Figure B). NOTE: For optimum performance and system longevity, distribute the load evenly. DISENGAGEMENT INSTRUCTIONS 1. Turn the engagement knob counter-clockwise to the open, disengaged position (Figure A). The triangle will point down. Figure A. Disengaged ITA and receiver. 2. Remove ITA. NOTE: For unbalanced load, add force to the lower pin load during disengagement to prevent binding. Figure B. Engaged ITA and receiver. 2-1 For the most current information available, visit www.vpc.com 4/23/15 VIRGINIA PANEL CORPORATION i2 MICRO iCON USER’S MANUAL: SECTION 3 i2 MICRO iCON RECEIVER MOUNTING PART # 310 130 XXX 4 FOR MOUNTING PLATES .09" THICK OR LESS .100 THRU, TYP. 4 PLCS FOR MOUNTING PLATES THICKER THAN .09" .086-56UNC-2B THRU, TYP. 4 PLCS. 16.26 .640 TYP. 1.27 .050 TYP. TOOLS REQUIRED Phillips Head Screwdriver 5.7 .23 MOUNTING INSTRUCTIONS 1. Prepare the mounting surface using the dimensions provided in Figure A. 2. Attach the i2 Micro iCon receiver to the panel with the provided 2-56 Phillips head screws and nuts (Figure B). Torque screws to 2 in-lbs [0.23 Nm]. NOTE: If the mounting surface is thicker than 0.125” [3.18 mm], longer screws may be needed. 100.07 3.940 88.6 3.49 5 NOTE: If the mounting surface has threaded holes, the nuts will not be needed. NOTE: M2 hardware can be used in place of the provided 2-56 hardware. NOTE: The dimensions shown reflect using a laser cutting or punch press process. If using conventional machining processes the 3.49” [88.65] dimension will be 3.69” [93.73] and a .09” [2.29] radius needs to be added to the corners. 5 TYP. 4.8 .19 TYP. 5 9.1 .36 TYP. 18.8 .74 TOLERANCES ARE: .XX = [.25].01 .XXX = [.13] .005 UNLESS OTHERWISE SPECIFIED 2.3 R.09 TYP. TABLE 1 PART NUMBER DESCRIPTION 410130101 410130104 ITA, i2 Micro iCon, 168 Position ITA, i2 Micro iCon, 120/12 Position Hybrid 410130106 410130115 ITA, i2 Micro iCon, 168 Position with Oversized Backshell ITA, i2 Micro iCon, 120/12 Position Hybrid with Oversized Backshell RECEIVER CUTOUT SPACING 1.00 [25.40] 1.00 [25.40] 2.19[55.63] 2.19[55.63] 4 SEE TABLE 1 FOR MINIMUM DISTANCE OF SUBSEQUENT SIDE BY SIDE CUTOUTS. *SPACING IS APPLICATION SPECIFIC, .80" MINIMUM, 1.00" RECOMMENDED Figure A. Recommended panel cutout. Figure B. If metric hardware is preferred, the supplied 2-56 hardware can be replaced with M2 hardware. 3-1 For the most current information available, visit www.vpc.com 4/23/15 VIRGINIA PANEL CORPORATION i2 MICRO iCON USER’S MANUAL: SECTION 6 i2 MICRO iCON CONTACT REMOVAL PART # 310 130 XXX, 410 130 XXX TOOLS REQUIRED Phillips Head Screwdriver Flat Blade Screwdriver Assembly Screws Panel Mounting Screws RECEIVER INSTRUCTIONS 1. Remove strain relief or keying pins (Section 7) if needed. 2. Using the Phillips head screwdriver, remove the four panel mounting screws from the top and bottom of the receiver (Figure A). 3. Using the flat head screwdriver, remove the two flat head assembly screws from the back of the receiver (Figure A). 4. Insert the flat blade screwdriver into the slot on the top of the receiver and pry the end of the receiver using a twisting motion until visible separation is indicated. Repeat on the opposite end of the receiver. 5. Grasp the receiver halves and apply force in opposite directions, rocking the ends of the receiver while slightly pulling the front of the receiver away from the mating back section. Be sure to open both sides of the receiver simultaneously or contacts could be damaged. 6. Extract the signal contact per the QuadraPaddle Users Manual. Reference Contact Part # 610 138 200 for Receiver Part # 310 130 101 or Contact Part # 610 138 216 for Receiver Part # 310 130 102. For Hybrid Receivers (Part #s 310 130 104 or 310 130 105): 7. Extract the power contact per the Micro Power Users Manual. Reference Contact Part # 610 142 101. Figure A. i2 Micro iCon Receiver separation. Panel Mounting Screws Assembly Screws 8. Extract the coaxial contact per the Micro Coaxial Users Manual. Reference Contact Part # 610 140 XXX. ITA INSTRUCTIONS 1. Refer to Section 4 for ITA Cover Removal Instructions. 2. Extract the signal contact per the QuadraPaddle Users Manual. Reference Contact Part # 610 138 109 or 610 138 112. For Hybrid ITA (Part # 410 130 104): 3. Extract the power contact per the Micro Power Users Manual. Reference Contact Part # 610 143 101. 4. Extract the coaxial contact per the Micro Coaxial Users Manual. Reference Contact Part # 610 141 XXX. 6-1 Figure B. i2 Micro iCon Hybrid Receiver separation. For the most current information available, visit www.vpc.com 4/23/15