Filename: tfs 433z.doc Version 1.2 Vectron International 07.01.2014 Filter specification TFS 433Z 1/5 Measurement condition Ambient temperature: Input power level: Terminating impedance: * Input: Output: 23 0 °C dBm 113 Ω || 5.7 pF 113 Ω || 5.7 pF Characteristics Remark: The reference level for the relative attenuation arel of the TFS 433Z is the minimum of the pass band attenuation amin. The minimum of the pass band attenuation amin is defined as the insertion loss ae. The centre frequency fc is the arithmetic mean value of the upper and lower frequencies at the 3 dB filter attenuation level relative to the insertion loss ae. The nominal frequency fN is fixed at 433,92 MHz without any tolerance. The given values for both the relative attenuation arel and the group delay ripple have to be achieved at the frequencies given below even if the centre frequency fc is shifted due to the temperature coefficient of frequency TCf in the operating temperature range and due to a production tolerance for the centre frequency fc. Data typ. value Insertion loss (reference level) ae = amin Nominal frequency fN Centre frequency fC Bandwidth 2,2 - dB tolerance / limit max. 3,0 - - 433,92 433,92 MHz - 695 kHz dB MHz BW 3 dB Relative attenuation min. 640 kHz max. 760 kHz arel 433,76 433,74 433,70 MHz MHz MHz … … … 434,08 434,10 434,14 MHz MHz MHz 10,00 414,00 424,50 431,72 432,12 434,92 442,00 550,00 700,00 805,00 MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz … 414,00 … 424,50 … 431,72 … 432,12 … 433,10 … 442,00 … 550,00 … 700,0 … 805,00 … 1000,00 MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz 0,55 0,64 0,65 60 49 47 50 35 13 44 59 43 72 dB dB dB max. max. max. 2,0 3,0 6,0 dB dB dB dB dB dB dB dB dB dB min. min. min. min. min. min. min. min. min. min. 53 46 31 39 8 10 36 53 40 53 dB dB dB dB dB dB dB dB dB dB dB dB dB Input power level - max. 0 dBm Permissible DC voltage - max. 6 V Operable temperature range - - 45 °C ... + 120°C Operating temperature range OTR Storage temperature range Frequency inversion temperature T0 Temperature coefficient of frequency TCf ** - - 40 °C ... + 95°C - - 45 °C ... + 130°C 30 - 0.033 °C ppm/K2 *) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference values only. Should there be additional questions, do not hesitate to ask for an application note or contact our design team. **) ∆f(Hz) = TCf(ppm/K²) x (T0-T)² x fT0(MHz). Generated: Checked / Approved: Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 433z.doc Version 1.2 Vectron International 07.01.2014 Filter specification TFS 433Z 2/5 0 0 -10 -1 -20 -2 -30 -3 magnitude in dB magnitude in dB Filter characteristic -40 -50 -60 -4 -5 -6 -70 -7 -80 -8 -90 -9 -100 210 290 370 450 530 610 690 frequency in MHz 770 850 930 -10 433.4 1010 433.5 433.6 433.7 433.8 433.9 434 frequency in MHz 434.1 434.2 434.3 434.4 Construction and pin connection (All dimensions in mm) 7 5 433Z ● E02 3 7 5 Year + week 2014 2015 2016 0,1 1,1 120° +0,15 1,1 Date code: E F G ... 1,8 Max. 1 Input Ground Ground Ground Output Ground Ground Ground Date cod e 0,64 3 5 - 0,10 1 1 2 3 4 5 6 7 8 2,54 50 Ω Test circuit L1 1 5 L2 SAW C2 C1 2, 3, 4, 6, 7, 8 Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 433z.doc Version 1.2 Vectron International 07.01.2014 Filter specification TFS 433Z 3/5 Stability characteristics, reliability After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 1 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 2. Vibration: 10 Hz to 500 Hz, 0.35 mm or g respectively, 1 octave per min, 10 cycles per plane, 3 planes; DIN IEC 68 T2 - 6 3. Change of temperature: 4. Resistance to solder heat (reflow): -55 °C to 125°C / 15 min. each / 100 cycles DIN IEC 68 part 2 – 14 Test N reflow possible: three times max.; for temperature conditions, see page 4: "Air reflow temperature conditions" This filter is RoHS compliant (2011/65/EU) Packing Tape & Reel: IEC 286 – 3, with exception of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: reel of empty components at start: reel of empty components at start including leader: trailer: 3000 min. 300 mm min. 500 mm min. 300 mm Pull Off Direc tion Tape (all dimensions in mm) W : 12,00 ± 0,3 Po : 4,00 ± 0,1 Do : 1,50 +0,1/-0 E : 1,75 ± 0,1 F : 5,50 ± 0,05 G(min) : 0,75 P2 : 2,00 ± 0,05 P1 : 8,00 ± 0,1 D1(min) : 1,50 Ao : 5,30 ± 0,1 Bo : 5,30 ± 0,1 Ct : 9,5 ± 0,1 P1 Da te Cod e t Po P2 W G Ct Bo F G E Do Ko Typ PIN Marker D1 Ao W 2 Reel (all dimensions in mm) A : 330 W1 : 12,4 +2/-0 W2(max) : 18,4 N(min) : 50 C : 13,0 +0,5/-0,2 C A N W 1 The minimum bending radius is 45 mm. Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 433z.doc Version 1.2 Vectron International 07.01.2014 Filter specification TFS 433Z 4/5 Air reflow temperature conditions Conditions Average ramp-up rate (30°C to 217°C) > 100°C > 150°C > 217°C Peak temperature Time within 5°C of actual peak temperature Cool-down rate (Peak to 50°C) Time from 30°C to Peak temperature Exposure less than 3°C/second between 300 and 600 seconds between 240 and 500 seconds between 30 and 150 seconds max. 260°C between 10 and 30 seconds less than 6°C/second no greater than 300 seconds Chip-mount air reflow profile Temperature / °C max. 260°C 217°C max. 300 s 10 ... 30 s Time / s 30 ... 150 s Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 433z.doc Vectron International Version 1.2 Filter specification 07.01.2014 TFS 433Z 5/5 History Version Reason of Changes Name Date 1.0 - Generation of development specification Channaa 25.01.2006 1.1 - Add typical values, change limit of attenuation - add filter characteristic, add test circuit - Generation of filter specification Channaa 03.02.2006 1.2 - maximum input power updated Kortenbeutel 07.01.2014 Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.