Filename: tfs133d.doc Version 2.0 Vectron International 27.04.2012 Filter specification TFS 133D 1/5 Measurement condition Ambient temperature: Input power level: Terminating impedance: * Input: Output: External Coil: 25 0 °C dBm 1275 Ω || -1,25 pF 1275 Ω || -1,25 pF 470 nH Characteristics Remark: The reference level for the relative attenuation arel of TFS 133C is the minimum of the pass band attenuation amin. This value is defined as the insertion loss ae. The centre frequency fc is the arithmetic mean value of the upper and lower frequencies at the 3 dB filter attenuation level relative to the insertion loss ae. The temperature coefficient of frequency Tcf is valid for both the reference frequency fc and the frequency response of the filter in the operating temperature range. The variation of the filter band width in the operating temperature range (OTR) is included in the production tolerance scheme. Data typ. value Insertion loss (reference level) Centre frequency at ambient temperature Passband 55 fC fC fC ± + 190 128,2 1,2 fC 133,2 p-p Relative attenuation ± 3,3 dB 6,0 dB ± 10,0 kHz ± 55,0 kHz 1,0 dB max. 2,0 dB 1,0 2,5 dB dB max. max. 2,0 3,0 dB dB dB dB dB min. min. min. 35 50 50 dB dB dB fC arel … fC fC ± ± 55 75 kHz kHz kHz … fC MHz … fC MHz … fC ± + 1,2 1,2 66,8 MHz MHz ** MHz *** kHz max. MHz PB Pass band ripple fC fC ae tolerance / limit 37 70 55 Absolute group delay within PB 7,5 µs max. 12 µs Group delay ripple within PB 2,8 µs max. 6 µs Permissible DC voltage - max. 5 V - - 55 °C ... + 90 °C - 55 °C ... + 90 °C Operating temperature range Storage temperature range OTR Frequency inversion temperature Temperature coefficient of frequency TCf **** 20 -0,036 °C ppm/K2 - *) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference values only. Should there be additional questions do not hesitate to ask for an application note or contact our design team. **) The attenuation of coupling coil resonance can be down to 40 dB. The exact position will be defined. ***) 2 narrow band distortions below 35 dB are acceptable. ****) ∆f(Hz) = TCf(ppm/K²) x (T-T0)² x fTo(MHz) Generated: Checked / Approved: Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs133d.doc Version 2.0 Vectron International 27.04.2012 Filter specification TFS 133D 2/5 Filter characteristic insertion loss: -3.31 dB 10.73 0 10.0244 -10 -2 9.3188 -20 -3 8.6132 -30 -4 7.9076 -40 -5 7.202 -6 6.4964 -7 5.7908 -70 -8 5.0852 -80 -9 4.3796 -90 -10 133 133.04 133.08 133.12 133.16 133.2 133.24 frequency in MHz 133.28 133.32 133.36 magnitude in dB -1 delay in µs magnitude in dB 0 3.674 133.4 -50 -60 -100 132.7 132.8 132.9 133 133.1 133.2 133.3 frequency in MHz 133.4 133.5 133.6 133.7 Construction and pin connection (All dimensions in mm) S 133D C17 1 3 Date code 2 Max. ● 1 5,2 Max. 2,54 ±0,2 7,2 Max. 2,54 ±0,2 1 1 2 3 4 5 6 7 8 9 10 11 12 Output Output Ground External Coil Ground Ground Input RF Return Input Ground Ground Ground Ground Date code: C D E ... Year + week 2012 2013 2014 0,80 50 Ohm Test circuit 1 8 L1 L2 C1 7 SAW 2 C2 L4 4 3, 5, 6, 9, 10, 11, 12 L3 Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs133d.doc Version 2.0 Vectron International 27.04.2012 Filter specification TFS 133D 3/5 Stability characteristics, reliability After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 1 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 2. Vibration: 10 Hz to 500 Hz, 0,35 mm or 5 g respectively, 1 octave per min, 10 cycles per plan, 3 plans; DIN IEC 68 T2 - 6 3. Change of temperature: 4. Resistance to solder heat (reflow): 5. ESD -55 °C to 125°C / 30 min. each / 10 cycles DIN IEC 68 part 2 – 14 Test N reflow possible: three times max.; for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4; MIL-STD-883E using coupling network of ISO 10605 and EN 6100-4-2 HBM:250V; This filter is RoHS compliant (2002/95/EG, 2005/618/EG) Packing Tape & Reel: IEC 286 – 3, with exception of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: reel of empty components at start: reel of empty components at start including leader: trailer: 3000 min. 300 mm min. 500 mm min. 300 mm Pull Off Direction Tape (all dimensions in mm) W : 16,00 +0,3/-0,1 Po : 4,00 ± 0,1 Do : 1,50 +0,1/-0 E : 1,75 ± 0,1 F : 7,50 ± 0,1 G(min) : 0,75 P2 : 2,00 ± 0,1 P1 : 8,00 ± 0,1 D1(min) : 1,50 Ao : 5,40 ± 0,1 Bo : 7,60 ± 0,1 Ct : 13,3 ± 0,1 P1 t Po P2 W G Ct Bo F G E Do PIN Marker Ko Date Code Typ D1 Ao W 2 Reel (all dimensions in mm) A : 330 W1 : 16,4 +2/-0 W2(max) : 22,4 N(min) : 50 C : 13,0 +0,5/-0,2 C A N W 1 The minimum bending radius is 45 mm. Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs133d.doc Version 2.0 Vectron International 27.04.2012 Filter specification TFS 133D 4/5 Air reflow temperature conditions Conditions Average ramp-up rate (30°C to 217°C) > 100°C > 150°C > 217°C Peak temperature Time within 5°C of actual peak temperature Cool-down rate (Peak to 50°C) Time from 30°C to Peak temperature Exposure less than 3°C/second between 300 and 600 seconds between 240 and 500 seconds between 30 and 150 seconds max. 260°C between 10 and 30 seconds less than 6°C/second no greater than 300 seconds Chip-mount air reflow profile Temperature / °C max. 260°C 217°C max. 300 s 10 ... 30 s Time / s 30 ... 150 s Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs133d.doc Vectron International Version 2.0 Filter specification 27.04.2012 TFS 133D 5/5 History Version Reason of Changes Name Date 1.0 - Generation of development specification Dr. Wall 14.01.2011 1.1 - Generation of filter specification - Added typical values - Added filter chareteristic - Updated tape and reel section Martens 23.06.2011 2.0 - removed input power level requirement Martens 27.04.2012 Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.