TFS120E - Vectron International

Filename:TFS120E.doc
Version 2.0
Vectron International
21.09.2012
Filter specification
TFS 120E
1/5
Measurement condition
Ambient temperature:
Input power level:
Terminating impedance: *
Input:
Output:
23
0
°C
dBm
1080 Ω || -7,4 pF
1250 Ω || -6,7 pF
Characteristics
Remark:
The reference level for the relative attenuation arel of the TFS 120E is the minimum of the pass band attenuation amin. The minimum of the pass band
attenuation amin is defined as the insertion loss ae. The centre frequency fc is the arithmetic mean value of the upper and lower frequencies at the 3 dB filter
attenuation level relative to the insertion loss ae. The nominal frequency fN is fixed at 120 MHz without any tolerance. The given values for both the relative
attenuation arel and the group delay ripple have to be achieved at the frequencies given below even if the centre frequency fc is shifted due to the
temperature coefficient of frequency TCf in the operating temperature range and due to a production tolerance for the centre frequency fc.
Data
typ. value
Insertion loss
(reference level)
ae
Nominal frequency
fN
-
Centre frequency
fC
120
MHz
PB
290
kHz
1 dB Passband
dB
max.
7
120
dB
MHz
fN ± 100
kHz
arel
Relative attenuation
fN
6
tolerance / limit
0.1
MHz
dB
max.
1
dB
0.5
0.7
1.05
1
1.35
80
MHz
MHz
MHz
MHz
MHz
MHz
15
32
32
39
39
48
dB
dB
dB
dB
dB
dB
min.
min.
min.
min.
min.
min.
10
25
25
35
35
45
dB
dB
dB
dB
dB
dB
80
MHz
48
dB
min.
45
dB
650
ns
max.
1000
ns
Input power level **
max.
18
dBm
Permissible DC voltage between any two terminals
max.
10
V
fN
fN
fN
fN
fN
fN
... fN ±
±
+
+
-
0.3
0.5
0.5
0.7
1.05
1
MHz
MHz
MHz
MHz
MHz
MHz
...
...
...
...
...
...
fN
fN
fN
fN
fN
fN
±
+
+
-
fN +
1.35
MHz ... fN +
Group delay ripple within PB
Operating temperature range
OTR
Storage temperature range
-
Frequency inversion temperature
Temperature coefficient of frequency
0.5
TCf ***
29
°C
-0.04
ppm/K²
- 35 °C ... + 85
°C
- 40 °C ... + 85
°C
-
*) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference values
only. Should there be additional questions do not hesitate to ask for an application note or contact our design team
**) This power level is only allowed for short term operation (10% of the life time), the max. input power for continuous operation is max.10dBm only
***) ∆f(Hz) = TCf(ppm/K2) x (T-T0)2 x fTo(MHz)
Generated:
Checked / Approved:
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice.
No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or
information..
Filename:TFS120E.doc
Version 2.0
Vectron International
21.09.2012
Filter specification
TFS 120E
2/5
Filter characteristic
0
0
3.5
-1
3.3368
-2
3.1736
-3
3.0104
-4
2.8472
-5
2.684
-6
2.5208
-7
2.3576
-8
2.1944
-9
2.0312
magnitude in dB
magnitude in dB
-20
-30
-40
delay in µs
-10
-50
-60
117.6
118.2
118.8
119.4
120
120.6
frequency in MHz
121.2
121.8
-10
119.7
122.4
119.76
119.82
119.88
119.94
120
120.06
frequency in MHz
120.12
120.18
120.24
1.868
120.3
Construction and pin connection
(All dimensions in mm)
TFS 120E
●
U30
10
1,0± 0,2
1,91± 0,2
7,62± 0,2
5
Date code
1,9± 0,2
1
1,8± 0,2
6,5 ± 0,2
13,3 ± 0,2
1
2
3
4
5
6
7
8
9
10
Input
Ground
Ground
Ground
Output
Output
Ground
Ground
Ground
Input
Date code:
U
V
W
...
Year + week
2006
2007
2008
6
200 Ω Test circuit
1
L1
C1
L2
10
5
SAW
L
C
6
L
2, 3, 4, 7, 8, 9
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice.
No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or
information..
Filename:TFS120E.doc
Version 2.0
Vectron International
21.09.2012
Filter specification
TFS 120E
3/5
Stability characteristics, reliability
After the following tests the filter shall meet the whole specification:
1. Shock:
500g, 1 ms, half sine wave, 3 shocks each plane;
DIN IEC 68 T2 - 27
2. Vibration:
10 Hz to 500 Hz, 0,35 mm or 5 g respectively, 1 octave per min, 10 cycles per plane, 3 planes;
DIN IEC 68 T2 - 6
3. Change of
temperature:
4. Resistance to
solder heat (reflow):
-55 °C to 125°C / 30 min. each / 10 cycles
DIN IEC 68 part 2 – 14 Test N
reflow possible: three times max.;
for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4;
This filter is RoHS compliant (2002/95/EG, 2005/618/EG)
Packing
Tape & Reel:
IEC 286 – 3, with exception of value for N and minimum bending radius;
tape type II, embossed carrier tape with top cover tape on the upper side;
max. pieces of filters per reel:
reel of empty components at start:
reel of empty components at start including leader:
trailer:
1700
min. 300 mm
min. 500 mm
min. 300 mm
Pull Off Direction
Tape (all dimensions in mm)
W
:24,00 +0,30/-0,10
Po
:4,00
± 0,1
Do
:1,50
+0,1/-0
E
:1,75
± 0,10
F
:11,50 ± 0,10
G(min)
:0,60
P2
:2,00
± 0,1
P1
:12,00 ± 0,1
D1(min)
:1,50
Ao
:7,10
± 0,10
Bo
:13,90 ± 0,10
Ct
:21,5
± 0,1
P1
Date Code
Po
Do
P2
W
G
Ct
Bo
F
G
E
t
Ko
Typ
PIN Marker
D1
Ao
W 2
Reel (all dimensions in mm)
A
: 330
W1
:24,4
+2/-0
W2(max) :30,4
N(min)
: 60
C
:13,0
+0,5/-0,2
C
A
N
W 1
The minimum bending radius is 45 mm.
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice.
No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or
information..
Filename:TFS120E.doc
Version 2.0
Vectron International
21.09.2012
Filter specification
TFS 120E
4/5
Air reflow temperature conditions
Conditions
Average ramp-up rate (30°C to 217°C)
> 100°C
> 150°C
> 217°C
Peak temperature
Time within 5°C of actual peak temperature
Cool-down rate (Peak to 50°C)
Time from 30°C to Peak temperature
Exposure
less than 3°C/second
between 300 and 600 seconds
between 240 and 500 seconds
between 30 and 150 seconds
max. 260°C
between 10 and 30 seconds
less than 6°C/second
no greater than 300 seconds
Chip-mount air reflow profile
Temperature / °C
max. 260°C
217°C
max. 300 s
10 ... 30 s
Time / s
30 ... 150 s
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice.
No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or
information..
Filename:TFS120E.doc
Vectron International
Version 2.0
Filter specification
21.09.2012
TFS 120E
5/5
History
Version
Reason of Changes
Name
Date
1.0
- generate development specification
Martens
27.10.2004
1.1
- change stability characteristics and correct relative attenuation
Strehl
18.05.2006
1.2
- terminating impedances, typical values, filter characteristics and matching configuration added
Pfeiffer
27.07.2006
2.0
- upper rejection relaxed as per customer discussion (21.09.2012)
TCUK
21.09.2012
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice.
No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or
information..