TFS1238

Filename: tfs 1238.doc
Version 1.3
Vectron International
18.04.2014
Filter specification
TFS 1238
1/5
Measurement condition
Ambient temperature:
Input power level:
Terminating impedance:
Input:
Output:
23
0
°C
dBm
49 Ω || -1.4 pF
49 Ω || -1.4 pF
Characteristics
Remark:
The maximum attenuation in the pass band is defined as the insertion loss ae. The nominal frequency fN is fixed at 1238.0 MHz without any tolerance or
limit. The values of absolute attenuation aabs are guaranteed for the whole operating temperature range. The frequency shift of the filter in the operating
temperature range is included in the production tolerance scheme.
Data
typ. value
Insertion loss in PB
ae
3.8
Nominal frequency
fN
-
Passband
PB
Passband ripple
Passband variation
p-p
Absolute attenuation
0.3
dB
1.0
1.5
tolerance / limit
max.
fN
dB
dB
max.
max.
5.0
±
dB
1238.0
MHz
41.0
MHz
1.5
3.0
dB
dB
aabs
MHz
… 1000
MHz
29
dB
min.
25
dB
1000
MHz
… 1100
MHz
29
dB
min.
25
dB
1100
MHz
… 1150
MHz
26
dB
min.
10
dB
1325
MHz
… 1350
MHz
14
dB
min.
10
dB
1350
MHz
… 1900
MHz
30
dB
min.
25
dB
1900
MHz
… 3000
MHz
34
dB
min.
25
dB
***)
Group delay ripple
-
1197
MHz
… 1228
MHz
7
ns
max.
10
ns
1237
MHz
… 1254
MHz
5
ns
max.
10
ns
1258.5
MHz
… 1278.5
MHz
8
ns
max.
10
ns
3
ns
max.
+/- 5
ns
15
dB
min.
8
dB
max.
10
Group delay variation
(unit to unit)
Return loss within PB
*)
Input power level in PB
Operating temperature range
OTR
Storage temperature range
Temperature coefficient of frequency
-
- 40 °C ... + 85°C
TCf **)
-74
dBm
- 40 °C ... + 85°C
ppm/K
*) measured at: 1197 MHz, 1238 MHz and 1278.5 MHz
**) ∆fc(Hz) = Tcf(ppm/K) x (T - To) x fCAT (MHz)
***) if on PCB Pin 4 and 8 is not connected ; stop band rejection decreases typically by 15dB
Generated:
Checked / Approved:
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice.
No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or
information.
Filename: tfs 1238.doc
Version 1.3
Vectron International
18.04.2014
Filter specification
TFS 1238
2/5
Filter characteristic
0
-10
0
0.04
-1
0.035
-2
0.03
-3
0.025
-4
0.02
-5
0.015
-6
0.01
-7
0.005
-8
0
-9
-0.005
S 21 in d B
S 21 in d B
-30
-40
-50
G D R in µs
-20
-60
-70
-80
500
1000
1500
frequency in MHz
2000
2500
3000
-10
1163
1179
1195
1211
1227
1243
1259
frequency in MHz
1275
1291
1307
-0.01
1323
Construction and pin connection
(All dimensions in mm)
6
7
5
C38
● D45
8
Date code:
D
E
F
...
Year + week
2013
2014
2015
1 ,0 +/-0,15
Date code
0,6 +/-0,15
7
3 ,0 +/-0,15
3
0,6 +/-0,15
1
°
60
Ground
Input
Ground
Ground
Ground
Output
Ground
Ground
3
2
1
4
1
2
3
4
5
6
7
8
5
0,6 +/-0,15
3 ,0 +/-0,15
50 Ω Test circuit
2
6
SAW
L2
L1
1, 3, 4, 5, 7, 8
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice.
No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or
information.
Filename: tfs 1238.doc
Version 1.3
Vectron International
18.04.2014
Filter specification
TFS 1238
3/5
Stability characteristics, reliability
After the following tests the filter shall meet the whole specification:
1. Shock:
500g, 1 ms, half sine wave, 3 shocks each plane;
DIN IEC 68 T2 - 27
2. Vibration:
10 Hz to 500 Hz, 0.35 mm or 5 g respectively, 1 octave per min, 10 cycles per
plane, 3 planes; DIN IEC 68 T2 - 6
3. Change of
temperature:
4. Resistance to
solder heat (reflow):
-55 °C to 125°C / 15 min. each / 100 cycles
DIN IEC 68 part 2 – 14 Test N
reflow possible: three times max.;
for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4;
This filter is RoHS compliant (2011/65/EU)
Packing
Tape & Reel:
IEC 286 – 3, with exception of value for N and minimum bending radius;
tape type II, embossed carrier tape with top cover tape on the upper side;
max. pieces of filters per reel:
reel of empty components at start:
reel of empty components at start including leader:
trailer:
3000
min. 300 mm
min. 500 mm
min. 300 mm
Pull Off Direction
Tape (all dimensions in mm)
W
: 8,00 ± 0,3
Po
: 4,00 ± 0,1
Do
: 1,50 +0,1/-0
E
: 1,75 ± 0,1
F
: 3,50 ± 0,05
G(min)
: 0,75
P2
: 2,00 ± 0,05
P1
: 4,00 ± 0,1
D1(min)
: 1,50
Ao
: 3,25 ± 0,1
Bo
: 3,25 ± 0,1
Ct
: 5,3 ± 0,1
P1
t
PIN Marker
Po
P2
W
G
Ct
Bo
F
G
E
Do
Ko
Date Code
Typ
D1
Ao
W 2
Reel (all dimensions in mm)
A
: 180
W1
: 8,4 +1,5/-0
W2(max) : 14,4
N(min)
: 60
C
: 13,0 ± 0,2
C
A
N
W 1
The minimum bending radius is 45 mm.
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice.
No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or
information.
Filename: tfs 1238.doc
Version 1.3
Vectron International
18.04.2014
Filter specification
TFS 1238
4/5
Air reflow temperature conditions
Conditions
Average ramp-up rate (30°C to 217°C)
> 100°C
> 150°C
> 217°C
Peak temperature
Time within 5°C of actual peak temperature
Cool-down rate (Peak to 50°C)
Time from 30°C to Peak temperature
Exposure
less than 3°C/second
between 300 and 600 seconds
between 240 and 500 seconds
between 30 and 150 seconds
max. 260°C
between 10 and 30 seconds
less than 6°C/second
no greater than 300 seconds
Chip-mount air reflow profile
Temperature / °C
max. 260°C
217°C
max. 300 s
10 ... 30 s
Time / s
30 ... 150 s
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice.
No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or
information.
Filename: tfs 1238.doc
Vectron International
Version 1.3
Filter specification
18.04.2014
TFS 1238
5/5
History
Version
Reason of Changes
Name
Date
1.0
Generation of development specification
Noack
01.08.2013
1.1
Change data table (typo group delay ripple )
Noack
01.08.2013
1.2
Generation of filter specification
Add typical values and filter characteristic
Noack
08.11.2013
Change data table
Noack
18.03.2014
1.3
Vectron International GmbH
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice.
No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or
information.