Filename: tfs 850e_11.doc Version 1.1 Vectron International 10.08.2011 Filter specification TFS 850E 1/5 Measurement condition Ambient temperature: Input power level: Terminating impedance: Input: Output: 23 0 °C dBm 50 50 Ω Ω Characteristics Remark: The maximum attenuation in the pass band is defined as the insertion loss ae. The nominal frequency fN is fixed at 850 MHz without any tolerance or limit. The values of absolute attenuation aabs are guaranteed for the whole operating temperature range. The frequency shift of the filter in the operating temperature range is included in the production tolerance scheme. Data typ. value ae fN Insertion loss in PB Nominal frequency Passband PB Bandwidth BW 2 dB 2 dB 40 dB Absolute attenuation 1.4 dB tolerance / limit max. 3.5 - 850.0 - fN ± 7 dB MHz MHz 32 32 49 MHz MHz MHz min. max. max. 30 35 120 MHz 35 dB min. 32 dB 885 MHz … 1500 MHz Group delay ripple within PB 38 23 dB ns min. max. 32 50 dB ns Return loss within PB 12.5 dB min. 11 dB 0.3 MHz … MHz MHz MHz aabs 815 Operating temperature range OTR - 45 °C ... + 85°C - Storage temperature range Temperature coefficient of frequency - TCf * -42 - 45 °C ... + 85°C ppm/K *) ∆fc(Hz) = Tcf(ppm/K) x (T - To) x fo (MHz). Generated: Checked / Approved: Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 850e_11.doc Version 1.1 Vectron International 10.08.2011 Filter specification TFS 850E 2/5 Filter characteristic 0 0 5 4.5 -10 -10 4 -20 3.5 -30 -40 3 -30 2.5 VSW R m a gnitud e in dB m a gnitud e in dB -20 2 -40 1.5 -50 1 -50 -60 0.5 -70 200 400 600 800 frequency in MHz 1000 1200 -60 1400 806.07 817.07 828.07 839.07 850.07 861.07 frequency in MHz 872.07 883.07 894.07 905.07 0 Construction and pin connection (All dimensions in mm) 7 850E ● B33 1 SQ 3,81 +0,2/-0,1 5 3 1 2 3 4 5 6 7 8 Ground Input Ground Ground Ground Output Ground Ground Date code: B C D ... Year + week 2011 2012 2013 7 5 0,1 12 0% 0,6 % d 3 1,78 2,54 1 1,2 Max. Date code 1,78 50 Ω Test circuit 2 6 L2 1, 3, 4, 5, 7, 8 Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 850e_11.doc Version 1.1 Vectron International 10.08.2011 Filter specification TFS 850E 3/5 Stability characteristics After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 18 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 2. Vibration: 10 Hz to 500 Hz, 0.35 mm or 5 g respectively, 1 octave per min, 10 cycles per plan, 3 plans; DIN IEC 68 T2 - 6 3. Change of temperature: 4. Resistance to solder heat (reflow): -55 °C to 125°C / 30 min. each / 10 cycles DIN IEC 68 part 2 – 14 Test N reflow possible: twice max.; for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4; Packing Tape & Reel: IEC 286 – 3, with exception of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: reel of empty components at start: reel of empty components at start including leader: trailer: 3000 min. 300 mm min. 500 mm min. 300 mm Pull Off Direction Tape (all dimensions in mm) W : 12.00 ± 0.3 Po : 4.00 ± 0.1 Do : 1.50 +0.1/-0 E : 1.75 ± 0.1 F : 5.50 ± 0.05 G(min) : 0.75 P2 : 2.00 ± 0.05 P1 : 8.00 ± 0.1 D1(min) : 1.50 Ao : 4.30 ± 0.1 Bo : 4.30 ± 0.1 Ct : 9.2 ± 0.1 P1 t PIN Marker Po P2 W G Ct Bo F G E Do Ko Date Code Typ D1 Ao W 2 Reel (all dimensions in mm) A : 330 W1 : 12.4 +2/-0 W2(max) : 18.4 N(min) : 50 C : 13.0 +0.5/-0.2 C A N W 1 The minimum bending radius is 45 mm. Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 850e_11.doc Version 1.1 Vectron International 10.08.2011 Filter specification TFS 850E 4/5 Air reflow temperature conditions Conditions Average ramp-up rate (30°C to 217°C) > 100°C > 150°C > 217°C Peak temperature Time within 5°C of actual peak temperature Cool-down rate (Peak to 50°C) Time from 30°C to Peak temperature Exposure less than 3°C/second between 300 and 600 seconds between 240 and 500 seconds between 30 and 150 seconds max. 260°C between 10 and 30 seconds less than 6°C/second no greater than 300 seconds Chip-mount air reflow profile Temperature / °C max. 260°C 217°C max. 300 s 10 ... 30 s Time / s 30 ... 150 s Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 850e_11.doc Vectron International Version 1.1 Filter specification 10.08.2011 TFS 850E 5/5 History Version Reason of Changes Name Date 1.0 - Generation of development specification S.Springfeldt 06.06.2011 1.1 - Generation of filter specification S.Springfeldt 10.08.2011 Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.