Filename: tfs 1191.doc Version 2.1 Vectron International 16.03.2012 Filter specification TFS 1191 1/5 Measurement condition Ambient temperature: Input power level: Terminating impedance: Input: Output: 23 0 °C dBm 50 Ω 50 Ω Characteristics The maximum attenuation in the passband is defined as the insertion loss ae. The nominal frequency fN is fixed at 1191MHz without any tolerance or limit. The values of absolute attenuation aabs are guaranteed for the whole operating temperature range. The frequency shift of the filter in the operating temperature range is included in the production tolerance scheme. Data typ. value Insertion loss in PB ae Nominal frequency fN - Passband PB - Passband ripple p-p Absolute attenuation 0,3 3,4 dB tolerance / limit max. fN 1,0 dB 4,0 ± dB 1191,0 MHz 27,0 MHz max. 2,0 dB aabs MHz … 1000 MHz 37 dB min. 30 dB 1000 MHz … 1130 MHz 19 dB min. 10 dB 1260 MHz … 1360 MHz 17 dB min. 10 dB 1360 MHz … 2500 MHz 36 dB min. 30 dB 2500 MHz … 4000 MHz 28 dB min. 24 dB 4000 MHz … 6000 MHz 12 dB min. 8 dB Group delay ripple 1164 MHz … 1189 MHz 5 ns max. 11 ns 1166 MHz … 1218 MHz 5 ns max. 11 ns 1164 MHz … 1218 MHz 5 ns max. 11 ns max. 2,3 : 1 max. 15 VSWR within PB 1,6 : 1 Input power level in PB Operating temperature range OTR Storage temperature range Temperature coefficient of frequency TCf* dBm - - 40 °C ... + 85°C - - 45 °C ... + 85°C -76 ppm/K *) ∆fc(Hz) = TCf (ppm/K) x (T – T0) x fCAT (MHz) Generated: Checked / Approved: Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 1191.doc Version 2.1 Vectron International 16.03.2012 Filter specification TFS 1191 2/5 Filter characteristic 5 -2 4.2 -3 3.8 -4 3.4 -5 3 -6 2.6 -7 2.2 -8 1.8 -9 1.4 -10 1131 1151 1171 1191 1211 frequency in MHz 1231 0 -10 magnitude in dB 4.6 VSWR magnitude in dB 0 -1 -20 -30 -40 -50 1 1251 -60 0 600 1200 1800 2400 3000 3600 frequency in MHz 4200 4800 5400 6000 Construction and pin connection (All dimensions in mm) 6 7 B91 ● C11 8 2 1 1,2 Max. 5 4 3 Date code d. Gr 3,0 +/-0,15 0,6 60 7 0,6 Ground Input Ground Ground Ground Output Ground Ground Date code: C D E ... Year + week 2012 2013 2014 3 1,5 1 1 2 3 4 5 6 7 8 5 0,6 50 Ohm Test circuit L1 2 6 L2 SAW 1, 3, 4, 5, 7, 8 Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 1191.doc Version 2.1 Vectron International 16.03.2012 Filter specification TFS 1191 3/5 Stability characteristics, reliability After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 1 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 2. Vibration: 10 Hz to 500 Hz, 0,35 mm or 5 g respectively, 1 octave per min, 10 cycles per plane, 3 planes; DIN IEC 68 T2 - 6 3. Change of temperature: 4. Resistance to solder heat (reflow): 5. ESD -55 °C to 125°C / 30 min. each / 10 cycles DIN IEC 68 part 2 – 14 Test N reflow possible: three times max.; for temperature conditions, see page 4: "Air reflow temperature conditions" ANSI/ESD S20.20-1999, class 1A for HBM This filter is RoHS compliant (2002/95/EG, 2005/618/EG) Packing Tape & Reel: IEC 286 – 3, with exception of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: reel of empty components at start: reel of empty components at start including leader: trailer: 3000 min. 300 mm min. 500 mm min. 300 mm Pull Off Direction Tape (all dimensions in mm) W : 8,00 ± 0,3 Po : 4,00 ± 0,1 Do : 1,50 +0,1/-0 E : 1,75 ± 0,1 F : 3,50 ± 0,05 G(min) : 0,75 P2 : 2,00 ± 0,05 P1 : 4,00 ± 0,1 D1(min) : 1,50 Ao : 3,25 ± 0,1 Bo : 3,25 ± 0,1 Ct : 5,3 ± 0,1 P1 t Po P2 W G Ct Bo F G E Do PIN Marker Ko Date Code Typ D1 Ao W 2 Reel (all dimensions in mm) A : 180 W1 : 8,4 +1,5/-0 W2(max) : 14,4 N(min) : 60 C : 13,0 ± 0,2 C A N W 1 The minimum bending radius is 45 mm. Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 1191.doc Version 2.1 Vectron International 16.03.2012 Filter specification TFS 1191 4/5 Air reflow temperature conditions Conditions Average ramp-up rate (30°C to 217°C) > 100°C > 150°C > 217°C Peak temperature Time within 5°C of actual peak temperature Cool-down rate (Peak to 50°C) Time from 30°C to Peak temperature Exposure less than 3°C/second between 300 and 600 seconds between 240 and 500 seconds between 30 and 150 seconds max. 260°C between 10 and 30 seconds less than 6°C/second no greater than 300 seconds Chip-mount air reflow profile Temperature / °C max. 260°C 217°C max. 300 s 10 ... 30 s Time / s 30 ... 150 s Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 1191.doc Vectron International Version 2.1 Filter specification 16.03.2012 TFS 1191 5/5 History Version Reason of Changes Name Date 1.0 - Generation of development specification S.Springfeldt 20.09.2011 2.0 - Absolute attenuation updated (2500 – 6000 MHz) A. Molke 25.11.2011 2.1 - Change from development spec to filter spec - Typical values added - Filter characteristic added A. Molke 16.03.2012 Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.