Filename: tfs 70l14.doc Version 2.0 Vectron International 05.10.2010 Filter specification TFS 70L14 1/5 Measurement condition Ambient temperature TA: Input power level: Terminating impedances in fc * ): 25 0 °C dBm for input: for output: 100 Ω ⎟⎢ - 15,914 pF. 131 Ω ⎟⎢ - 15,275 pF. Characteristics Remark: Reference level for the relative attenuation arel of the TFS 70L14 is the minimum of the pass band attenuation amin. The minimum of the pass band attenuation amin is defined as the insertion loss ae. The reference frequence fc is the arithmetic mean value of the upper and lower frequencies at the 3 dB filter attenuation level relative to the insertion loss ae. The temperature coefficient of frequency Tcf is valid both for the reference frequency fc and the frequency response of the filter in the operating temperature range. The frequency shift of the filter in the operating temperature range is not included in the production tolerance scheme. Data typ. value Insertion loss (reference level) ae 11 dB Centre frequency at TA fC 70 MHz Passband PB Amplitude ripple in PB p-p Passband 2 p-p max. 0,4 dB max. fC 0,5 12,5 dB 70,0±0,1 MHz fC PB2 Amplitude ripple in PB2 tolerance / limit dB max. ± 6,5 1 ± 6,0 0,5 MHz dB MHz dB Bandwidth at TA 1 dB 13,35 MHz min. 13 MHz 3 dB 14,5 MHz min. 14 MHz 0,4 0,5 2,1 43 43 dB dB dB dB dB max. max. max. min. min. 0.5 1 3 40 40 dB dB dB dB dB 1,1 µs max. ns max. 90 ns deg max. 11 deg Relative attenuation fC fC fC fC fC ± ± + 6 6,5 20 10,35 MHz MHz MHz MHz arel ... ... ... ... ... fC fC fC fC fC ± ± ± + 6 6,5 7 9,65 20 MHz MHz MHz MHz MHz Average group delay in PB Group delay ripple in fc ± 6,3 MHz p-p Phase linearity in fc ± 6,3 MHz p-p Operating temperature range OTR Storage temperature range Temperature coefficient of frequency TCf ** 65 6,5 1,5 - -20 °C ... + 70 °C - -40 °C ... + 85 °C -87 ppm/K µs - *) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference values only. Should there be additional questions do not hesitate to ask for an application note or contact our design team. **) ∆fc(Hz) = TCf(ppm/K) x (T - To) x fTo (MHz). Generated: Checked / Approved: Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 70l14.doc Version 2.0 Vectron International 05.10.2010 Filter specification TFS 70L14 2/5 0 1.61 -1 1.55 -16 -2 1.49 -24 -3 1.43 -4 1.37 -5 1.31 -6 1.25 -56 -7 1.19 -64 -8 1.13 -72 -9 1.07 -32 -40 -48 -80 50 54 58 62 66 70 74 frequency in MHz 78 82 86 -10 62 90 63.6 65.2 66.8 68.4 70 71.6 frequency in MHz 73.2 74.8 76.4 delay in µs 0 -8 magnitude in dB magnitude in dB Filter characteristic 1.01 78 Construction and pin connection (All dimensions in mm) TFS70L14 ● A40 6,8Max. 13,6Max. 2,54 ±0,15 2,54 ±0,15 1,5 1 2 3 4 2,0Max. 1 12 5 11 6 Date code 1 2 3 4 5 6 7 8 9 10 11 12 Ground Ground Ground Ground Output Output RF Return Ground Ground Ground Ground Input Input RF Return Date code: A B C ... Year + week 2010 2011 2012 10 9 8 7 0,8 0,1 50 Ω Test circuit 1 Scheme 1 2 3 L2 4 12 50 Ω C2 6 11 L1 50 Ω 5 C1 10 9 8 7 Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 70l14.doc Version 2.0 Vectron International 05.10.2010 Filter specification TFS 70L14 3/5 Stability characteristics After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 1 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 2. Vibration: 10 Hz to 500 Hz, 0,35 mm or 5 g respectively, 1 octave per min, 10 cycles per plan, 3 plans; DIN IEC 68 T2 - 6 3. Change of temperature: 4. Resistance to solder heat (reflow): -55 °C to 125°C / 30 min. each / 10 cycles DIN IEC 68 part 2 – 14 Test N reflow possible: twice max.; for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4; Packing Tape & Reel: IEC 286 – 3, with exeption of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters peer reel: reel of empty components at start: reel of empty components at start including leader: trailer: 1700 min. 300 mm min. 500 mm min. 300 mm Pull Off Direction Tape (all dimensions in mm) W : 24,00 +0,30/-0,10 Po : 4,00 ± 0,1 Do : 1,50 +0,1/-0 E : 1,75 ± 0,10 F : 11,50 ± 0,10 G(min) : 0,60 P2 : 2,00 ± 0,1 P1 : 12,00 ± 0,1 D1(min) : 1,50 Ao : 7,10 ± 0,10 Bo : 13,90 ± 0,10 Ct : 21,5 ± 0,1 t P1 Date Code Po P2 W G Ct Bo F G E Do Ko Typ PIN Marker D1 Ao W 2 Reel (all dimensions in mm) A : 330 W1 : 24,4 +2/-0 W2(max) : 30,4 N(min) : 60 C : 13,0 +0,5/-0,2 A C N W 1 The minimum bending radius is 45 mm. Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 70l14.doc Version 2.0 Vectron International 05.10.2010 Filter specification TFS 70L14 4/5 Air reflow temperature conditions Conditions Average ramp-up rate (30°C to 217°C) > 100°C > 150°C > 217°C Peak temperature Time within 5°C of actual peak temperature Cool-down rate (Peak to 50°C) Time from 30°C to Peak temperature Exposure less than 3°C/second between 300 and 600 seconds between 240 and 500 seconds between 30 and 150 seconds max. 260°C between 10 and 30 seconds less than 6°C/second no greater than 300 seconds Chip-mount air reflow profile Temperature / °C max. 260°C 217°C max. 300 s 10 ... 30 s Time / s 30 ... 150 s Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: tfs 70l14.doc Vectron International Version 2.0 Filter specification 05.10.2010 TFS 70L14 5/5 History Version Reason of Changes Name Date 1.0 - Generate Preliminary specification Dunzow 28.08.2001 1.1 - Generate Filter specification Dunzow 11.09.2001 2.0 - Passband 2 added - Amplitude ripple in passband 2 added Chilla 05.10.2010 Vectron International GmbH & Co. KG Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.