Filename: TFS1245A.doc Version 1.0 Vectron International 27.08.2013 Filter specification TFS 1245A 1/5 Measurement condition Ambient temperature: Input power level: Terminating impedance: Input: Output: 23 0 200 200 °C dBm Ω Ω Characteristics Remark: The maximum attenuation in the passband is defined as the insertion loss ae. The nominal frequency fN is fixed at 1245.5 MHz without any tolerance or limit. The values of absolute attenuation aabs are guaranteed for the whole operating temperature range. The frequency shift of the filter in the operating temperature range is included in the production tolerance scheme. Data typ. value Insertion loss in PB1 ae fN Nominal frequency 1.5 dB tolerance / limit max. 3.0 - dB 1245.5 MHz Passband 1 PB1 - fN ± 8.5 MHz Passband 2 PB2 - fN ± 4.0 MHz 2.0 dB Passband variation within PB1 Absolute attenuation 0,3 MHz … 1205 0.3 dB max. aabs MHz 35 dB min. 32 dB 1285 MHz … 2500 MHz Group delay ripple within PB1 40 6 dB ns min. max. 35 20 dB ns 3 ns max. 10 ns +/- 2 ns max. +/- 4 ns Group delay ripple within PB2 Group delay variation (unit to unit) * VSWR within PB1 1.9 : 1 max. Input power level in PB1 - max. - - 40 °C ... + 85°C Operating temperature range OTR Storage temperature range Temperature coefficient of frequency TCf ** -44 2.3 : 1 20 dBm - 45 °C ... + 85°C ppm/K *) measured at: fN , fN + 4 MHz , fN - 4 MHz **) ∆fc(Hz) = Tcf (ppm/K) x (T - To) x fCAT (MHz) Generated: Checked / Approved: Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: TFS1245A.doc Version 1.0 Vectron International 27.08.2013 Filter specification TFS 1245A 2/5 0.1 -1 0.09 -2 0.08 -3 0.07 -4 0.06 -5 0.05 -6 0.04 -7 0.03 -8 0.02 -9 0.01 1215.5 1225.5 1235.5 1245.5 1255.5 frequency in MHz 1265.5 0 -10 magnitude in dB 0 delay in µs magnitude in dB Filter characteristic -20 -30 -40 -50 1275.5 0 500 1000 1500 frequency in MHz 2000 2500 Construction and pin connection (All dimensions in mm) 6 7 C45A ● D35 8 4 3 2 1 1,2 Max. 5 Date code d. Gr 3,0 +/-0,15 0,6 60 7 0,6 Input 1 Ground Input 2 Ground Output 2 Ground Output 1 Ground Date code: D E F ... Year + week 2013 2014 2015 3 1,5 1 1 2 3 4 5 6 7 8 5 0,6 200 Ω Test circuit 7 1 3 SAW 5 2, 4, 6, 8 Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: TFS1245A.doc Version 1.0 Vectron International 27.08.2013 Filter specification TFS 1245A 3/5 Stability characteristics, reliability After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 1 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 2. Vibration: 10 Hz to 500 Hz, 0,35 mm or 5 g respectively, 1 octave per min, 10 cycles per plane, 3 planes; DIN IEC 68 T2 - 6 3. Change of temperature: 4. Resistance to solder heat (reflow): 5. ESD -55 °C to 125°C / 15 min. each / 100 cycles DIN IEC 68 part 2 – 14 Test N reflow possible: three times max.; for temperature conditions, see page 4: "Air reflow temperature conditions" ANSI/ESD S20.20-1999, class 1A for HBM This filter is RoHS compliant (2011/65/EU) Packing Tape & Reel: IEC 286 – 3, with exception of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: reel of empty components at start: reel of empty components at start including leader: trailer: 3000 min. 300 mm min. 500 mm min. 300 mm Pull Off Direction Tape (all dimensions in mm) W : 8,00 ± 0,3 Po : 4,00 ± 0,1 Do : 1,50 +0,1/-0 E : 1,75 ± 0,1 F : 3,50 ± 0,05 G(min) : 0,75 P2 : 2,00 ± 0,05 P1 : 4,00 ± 0,1 D1(min) : 1,50 Ao : 3,25 ± 0,1 Bo : 3,25 ± 0,1 Ct : 5,3 ± 0,1 P1 t Po P2 W G Ct Bo F G E Do PIN Marker Ko Date Code Typ D1 Ao W 2 Reel (all dimensions in mm) A : 180 W1 : 8,4 +1,5/-0 W2(max) : 14,4 N(min) : 60 C : 13,0 ± 0,2 C A N W 1 The minimum bending radius is 45 mm. Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: TFS1245A.doc Version 1.0 Vectron International 27.08.2013 Filter specification TFS 1245A 4/5 Air reflow temperature conditions Conditions Average ramp-up rate (30°C to 217°C) > 100°C > 150°C > 217°C Peak temperature Time within 5°C of actual peak temperature Cool-down rate (Peak to 50°C) Time from 30°C to Peak temperature Exposure less than 3°C/second between 300 and 600 seconds between 240 and 500 seconds between 30 and 150 seconds max. 260°C between 10 and 30 seconds less than 6°C/second no greater than 300 seconds Chip-mount air reflow profile Temperature / °C max. 260°C 217°C max. 300 s 10 ... 30 s Time / s 30 ... 150 s Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: TFS1245A.doc Vectron International Version 1.0 Filter specification 27.08.2013 TFS 1245A 5/5 History Version Reason of Changes Name Date 1.0 Generation of filter specification Molke 27.08.2013 Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.