Filename: TFS1251.doc Version 3.1 Vectron International 05.02.2015 Filter specification TFS 1251 1/5 Measurement condition Ambient temperature: Input power level: Terminating impedance: Input: Output: Source: Load: 23 0 200 200 °C dBm Ω Ω 198.2 Ω || -0.29 pF 198.2 Ω || -0.29 pF Characteristics Remark: The maximum attenuation in the passband is defined as the insertion loss ae. The nominal frequency fN is fixed at 1251.5 MHz without any tolerance or limit. The values of absolute attenuation aabs are guaranteed for the whole operating temperature range. The frequency shift of the filter in the operating temperature range is included in the production tolerance scheme. Data typ. value Insertion loss in PB ae fN Nominal frequency Passband PB Passband variation dB max. 4.5 - 1251.5 0.7 Absolute attenuation 0.3 3.8 tolerance / limit fN ± 34.5 dB max. 3.0 dB MHz MHz dB aabs MHz … 1155 MHz 28 dB min. 25 dB 1155 MHz … 1170 MHz 35 dB min. 15 dB 1340 MHz … 1355 MHz 39 dB min. 15 dB 1355 MHz … 3000 MHz 33 dB min. 25 dB Group delay ripple 1217 MHz … 1237 MHz 5 ns max. 10 ns 1237 MHz … 1254 MHz 5 ns max. 10 ns 1254 MHz … 1286 MHz 5 ns max. 10 ns Group delay variation (unit to unit) 1217 MHz … 1286 * MHz Return loss within PB Input power level in PB Operating temperature range ns max. +/-5 ns 18 dB min. 8 dB max. 10 OTR Storage temperature range Temperature coefficient of frequency +/-3 TCf ** - - 40 °C ... + 85°C - - 40 °C ... + 85°C -76 dBm ppm/K *) measured at: fN , fN + 34.5 MHz , fN – 34.5 MHz **) ∆fc(Hz) = Tcf (ppm/K) x (T - To) x fCAT (MHz) Generated: Checked / Approved: Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: TFS1251.doc Version 3.1 Vectron International 05.02.2015 Filter specification TFS 1251 2/5 0.03 -5 0.025 -10 -10 0.02 -20 -15 0.015 -20 0.01 -40 -25 0.005 -50 1150 1180 1210 1240 1270 frequency in MHz 1300 1330 0 S21 in dB 0 GDR in µs S21 in dB Filter characteristic 1360 -30 0 400 800 1200 1600 2000 frequency in MHz 2400 2800 3200 Construction and pin connection (All dimensions in mm) 6 7 C51 ● F06 8 1 1,2 Max. 5 2 4 1 2 3 4 5 6 7 8 Input 1 Ground Input 2 Ground Output 2 Ground Output 1 Ground Date code: F G H ... Year + week 2015 2016 2017 3 Date code 0,6 d. Gr 60 7 0,6 3,0 +/-0,15 3 1,5 1 5 0,6 200 Ω Test circuit 7 1 3 SAW 5 2, 4, 6, 8 Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: TFS1251.doc Version 3.1 Vectron International 05.02.2015 Filter specification TFS 1251 3/5 Stability characteristics, reliability After the following tests the filter shall meet the whole specification: 1. Shock: 500g, 1 ms, half sine wave, 3 shocks each plane; DIN IEC 68 T2 - 27 2. Vibration: 10 Hz to 500 Hz, 0,35 mm or 5 g respectively, 1 octave per min, 10 cycles per plane, 3 planes; DIN IEC 68 T2 - 6 3. Change of temperature: 4. Resistance to solder heat (reflow): -55 °C to 125°C / 15 min. each / 100 cycles DIN IEC 68 part 2 – 14 Test N reflow possible: three times max.; for temperature conditions, see page 4: "Air reflow temperature conditions" This filter is RoHS compliant (2011/65/EU) Packing Tape & Reel: IEC 286 – 3, with exception of value for N and minimum bending radius; tape type II, embossed carrier tape with top cover tape on the upper side; max. pieces of filters per reel: reel of empty components at start: reel of empty components at start including leader: trailer: 3000 min. 300 mm min. 500 mm min. 300 mm Pull Off Direction Tape (all dimensions in mm) W : 8,00 ± 0,3 Po : 4,00 ± 0,1 Do : 1,50 +0,1/-0 E : 1,75 ± 0,1 F : 3,50 ± 0,05 G(min) : 0,75 P2 : 2,00 ± 0,05 P1 : 4,00 ± 0,1 D1(min) : 1,50 Ao : 3,25 ± 0,1 Bo : 3,25 ± 0,1 Ct : 5,3 ± 0,1 P1 t PIN Marker Po P2 W G Ct Bo F G E Do Ko Date Code Typ D1 Ao W 2 Reel (all dimensions in mm) A : 330 or 180 W1 : 8,4 +1,5/-0 W2(max) : 14,4 N(min) : 60 C : 13,0 ± 0,2 C A N W 1 The minimum bending radius is 45 mm. Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: TFS1251.doc Version 3.1 Vectron International 05.02.2015 Filter specification TFS 1251 4/5 Air reflow temperature conditions Conditions Average ramp-up rate (30°C to 217°C) > 100°C > 150°C > 217°C Peak temperature Time within 5°C of actual peak temperature Cool-down rate (Peak to 50°C) Time from 30°C to Peak temperature Exposure less than 3°C/second between 300 and 600 seconds between 240 and 500 seconds between 30 and 150 seconds max. 260°C between 10 and 30 seconds less than 6°C/second no greater than 300 seconds Chip-mount air reflow profile Temperature / °C max. 260°C 217°C max. 300 s 10 ... 30 s Time / s 30 ... 150 s Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information. Filename: TFS1251.doc Vectron International Version 3.1 Filter specification 05.02.2015 TFS 1251 5/5 History Version Reason of Changes Name Date 1.0 - Generation of development specification A. Molke 09.01.2014 2.0 - Group delay limits relaxed A. Molke 30.06.2014 3.0 - Group delay limits of version 1.0 restored A. Molke 21.08.2014 3.1 - Change from development spec to filter spec - Typical values added - Filter characteristic added A. Molke 05.02.2015 Vectron International GmbH Potsdamer Straße 18 D 14 513 TELTOW / Germany Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30 E-Mail: [email protected] Vectron International GmbH reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.