TFS2595A - Vectron International

Filename: tfs 2595a.doc
Version 2.1
Vectron International
02.08.2011
Filter specification
TFS 2595A
1/5
Measurement condition
Ambient temperature:
Input power level:
Terminating impedance:
Input:
Output:
23
0
°C
dBm
50
50
Ω
Ω
Characteristics
Remark:
The maximum attenuation in the pass band is defined as the insertion loss ae. The nominal frequency fN is fixed at 2595A MHz without any tolerance or
limit. The values of absolute attenuation aabs are guaranteed within the operating temperature range OTR. The frequency shift of the filter in the operating
temperature range is included in the production tolerance scheme.
Data
typ. value
Insertion loss
ae
fN
Nominal frequency
Passband
... 2400
... 2930
... 6000
max.
fN
0,63
Absolute attenuation
MHz
MHz
MHz
dB
PB
Pass band variation
0,3
2875
2930
2,3
tolerance / limit
3,0
±
dB
2595,0
MHz
25
MHz
dB
max.
1,0
dB
24
33
20
dB
dB
dB
min.
min.
min.
20
25
10
dB
dB
dB
6
ns
max.
40
ns
3
ns
max.
15
ns
11,5
dB
min.
10
dB
max.
10**
dBm
aabs
MHz
MHz
MHz
Absolute group delay within PB
Group delay ripple within PB
p-p
Return loss within PB
Input power level
Operating temperature range
OTR
- 40 °C ... + 85 °C
Storage temperature range
Temperature coefficient of frequency
- 40 °C ... + 85 °C
TCf *
-46
ppm/K
*) ∆f(Hz) = TCf(ppm/K) x (T-T0) x fTo(MHz)
**) 22dBm/1minute @ 85°C
Generated:
Checked / Approved:
Vectron International GmbH & Co. KG
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without
notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such
product(s) or information.
Filename: tfs 2595a.doc
Version 2.1
Vectron International
02.08.2011
Filter specification
TFS 2595A
2/5
Filter characteristic
0
0
-5
4
-5
3.5
-10
-10
3
-15
-15
2.5
-25
-20
2
VSW R
m a g nitud e in d B
m a g nitud e in d B
-20
-25
-30
1.5
-30
-35
1
-35
-40
0.5
-40
-45
-50
500
1000
1500
2000
2500
3000
frequency in MHz
3500
4000
4500
5000
5500
-45
6000
2500
2550
2600
frequency in MHz
2650
2700
0
Construction and pin connection
(All dimensions in mm)
5
6
4
1,2 Max.
X95A
● B31
1
2
1
2
3
4
5
6
Ground
Input
Ground
Ground
Output
Ground
Date code:
B
C
D
...
Year + week
2011
2012
2013
3
Date code
3
0,75
3,0 +/-0,15
0,30X0,30
1
6
0,6
4
0,6
50 Ω Test circuit
L1
2
5
L2
SAW
1, 3, 4, 6
Vectron International GmbH & Co. KG
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without
notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such
product(s) or information.
Filename: tfs 2595a.doc
Version 2.1
Vectron International
02.08.2011
Filter specification
TFS 2595A
3/5
Stability characteristics, reliability
After the following tests the filter shall meet the whole specification:
1. Shock:
500g, 1 ms, half sine wave, 3 shocks each plane;
DIN IEC 68 T2 - 27
2. Vibration:
10 Hz to 500 Hz, 0,35 mm or 5 g respectively, 1 octave per min, 10 cycles per plane, 3 planes;
DIN IEC 68 T2 - 6
3. Change of
temperature:
4. Resistance to
solder heat (reflow):
5. ESD
-55 °C to 125°C / 30 min. each / 10 cycles
DIN IEC 68 part 2 – 14 Test N
reflow possible: three times max.;
for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4;
ANSI/ESD S20.20-1999, class 0 for HBM
This filter is RoHS compliant (2002/95/EG, 2005/618/EG)
Packing
Tape & Reel:
IEC 286 – 3, with exception of value for N and minimum bending radius;
tape type II, embossed carrier tape with top cover tape on the upper side;
max. pieces of filters per reel:
reel of empty components at start:
reel of empty components at start including leader:
trailer:
3000
min. 300 mm
min. 500 mm
min. 300 mm
Pull Off Direction
Tape (all dimensions in mm)
W
: 8,00 ± 0,3
Po
: 4,00 ± 0,1
Do
: 1,50 +0,1/-0
E
: 1,75 ± 0,1
F
: 3,50 ± 0,05
G(min)
: 0,75
P2
: 2,00 ± 0,05
P1
: 4,00 ± 0,1
D1(min)
: 1,50
Ao
: 3,25 ± 0,1
Bo
: 3,25 ± 0,1
Ct
: 5,3 ± 0,1
P1
t
PIN Marker
Po
P2
W
G
Ct
Bo
F
G
E
Do
Ko
Date Code
Typ
D1
Ao
W 2
Reel (all dimensions in mm)
A
: 180
W1
: 8,4 +1,5/-0
W2(max) : 14,4
N(min)
: 60
C
: 13,0 ± 0,2
C
A
N
W 1
The minimum bending radius is 45 mm.
Vectron International GmbH & Co. KG
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without
notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such
product(s) or information.
Filename: tfs 2595a.doc
Version 2.1
Vectron International
02.08.2011
Filter specification
TFS 2595A
4/5
Air reflow temperature conditions
Conditions
Average ramp-up rate (30°C to 217°C)
> 100°C
> 150°C
> 217°C
Peak temperature
Time within 5°C of actual peak temperature
Cool-down rate (Peak to 50°C)
Time from 30°C to Peak temperature
Exposure
less than 3°C/second
between 300 and 600 seconds
between 240 and 500 seconds
between 30 and 150 seconds
max. 260°C
between 10 and 30 seconds
less than 6°C/second
no greater than 300 seconds
Chip-mount air reflow profile
Temperature / °C
max. 260°C
217°C
max. 300 s
10 ... 30 s
Time / s
30 ... 150 s
Vectron International GmbH & Co. KG
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without
notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such
product(s) or information.
Filename: tfs 2595a.doc
Vectron International
Version 2.1
Filter specification
02.08.2011
TFS 2595A
5/5
History
Version
Reason of Changes
Name
Date
1.0
Generation of development specification
S.Springfeldt
25.10.2010
1.1
Generation of filter specification, change of filter orientation in ‘tape and reel’
S.Springfeldt
30.03.2011
2.0
Change of return loss to 10dB
S.Springfeldt
18.04.2011
2.1
Added ESD classification
S.Springfeldt
02.08.2011
Vectron International GmbH & Co. KG
Potsdamer Straße 18
D 14 513 TELTOW / Germany
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30
E-Mail: [email protected]
Vectron International GmbH & Co. KG reserves the right to make changes to the product(s) and/or information contained herein without
notice. No liability is assumed as a result of their use or application. No rights under any patent accompany the sale of any such
product(s) or information.