www.osram.com LINEARlight – LM01B preliminary Datasheet Product benefits Low profile Minimal heat generation Wide viewing angle Easy connection with OSRAM CONNECTsystem LM-2PIN and LM-2CONN Typical module efficiency up to 101 lm/W Applications Path illumination illumination, contour accentuation Edge-coupling of transparent or diffuse materials Emergency / rescue signs Technical Operating Data P d t Product Li ht Light N b Number V lt Voltage P Power R di Radiance C l Temp. Color T [K] L Lum. Flux Fl Color of LEDs [V DC]* [W]* Angle [°]* Wavelength [nm] [lm] LM01B-W2F-827 White 32 24 0.95 110 2700 90 LM01B-W2F-840 White 32 24 1.1 110 4000 110 LM01B-W2F-857 White 32 24 1.2 110 5700 115 LM01B-B2 Blue 32 24 2.8 120 470 30 All Data are related to the entire module. Due to the special conditions of the manufacturing processes of LED the typical data of technical parameters can only reflect statistical figures and do not necessarily correspond to the actual parameters of each single product which could differ from the typical data *) Preliminary Data Technical Features Dimension (L x W x H): 448 x 10 x 3.1 mm Dimmable FR4 PCB equipped with 32 Duris E3 LEDs Seamless concept with up to 10 modules in series Luminous flux 250 lm/m (4000K) Lifetime 50.000 h @L70 @tcmax 65°C 7-6-6-6-7 intervalls can bei cut out without Best efficacy in combination with OSRAM OPTOTRONIC® control gears damaging the rest of the module Size of smallest unit 7 LED (L x W): 98 x 10 mm Operation only with 24V constant voltage control gears Mounting holes for simple fixing with M4 screws Consistent white light < 5 SDCM Color rendering Ra typ. 85 LINEARlight LM01B 16.11.2012 Seite 1 von 4 www.osram.com Minimum and Maximum Ratings g Product LM01B Operating Temperature Storage Temperature Voltage Range Reverse Voltage at Tc-Point [C°]* [C°]* [V dc]* [V dc]* -30 … 75 -30 … 80 23 - 25 25 *) Exceeding maximum ratings for operating and storage temperature will reduce expected life time or destroy the LED Module. Exceeding maximum ratings for operating current will cause hazardous overload and will likely destroy the LED Module. The temperature of the LED module must be measured at the Tc-point according to EN60598-1 in a thermally constant status with a temperature sensor or a temperature sensitive label. For exact location of the Tc-point see drawing below. Drawing LINEARlight LM01B 16.11.2012 Seite 2 von 4 www.osram.com Safety Information The LED module itself and all its components must not be mechanically stressed. Assembly must not damage or destroy conducting paths on the circuit board. To avoid mechanical damage to the connecting cables, the module should be attached securely to the intended substrate. Heavy vibration should be avoided. The mounting of the module is carried out by attaching it at the mounting holes. Mounting screws should be treated with synthetic washers to prevent circuit board damage and possible short circuiting. In order to drive OSRAM LED-Modules safely, it is absolutely necessary to operate them with an electronically stabilised power supply protecting against short circuits, overload and overheating. To also ease the luminaire/installation approval, electronic control gear for LED or LED modules should carry the CE mark and be ENEC certified. In Europe the declarations of conformity must include the following standards: CE: EC 61347-2-13, EN 55015, IEC 61547 and IEC 61000-3-2 - ENEC: 61347-2-13 and IEC/EN 62384. Al check Also h k ffor th the mark k off an iindependent d d t authorized th i d certification tifi ti iinstitute. tit t OSRAM OPTOTRONIC® electronic control gear complies to all relevant standards and guarantees safe operation. Installation of LED modules (with power supplies) needs to be made with regard to all applicable electrical and safety standards. Only qualified personnel should be allowed to perform installations. Observe correct polarity! Depending on the product incorrect polarity will lead to emission of red or no light. The module can be destroyed! Correct polarity immediatelly! (see "reverse voltage", page 2). Parallel connection is highly recommended as safe electrical operation mode. Serial connection is not recommended. Unbalanced voltage drop can cause hazardous overload and damage the LED module. Pay attention to ESD steps when mounting and connecting the module. When do you use the connector LM-CONN pay attention that the modules are assembled in a level. No contact safety otherwise is given The LINEARlight can typically survive transient current levels of up to 2 Amperes. As a general design precaution, if the maximum output current of the power supply is more than 2 Amperes, fast- blow fuses should be incorporated into the wiring plan Electrical contact is achieved with the contact cables. A maximum number of 10 modules can be installed consecutively from one power feed. Operation with more than 10 consecutive modules will reduce photometric performance and exceed the current carrying capacity of the module. The module, as manufactured, has no conformal coating and therefore offers no inherent protection against corrosion. Damage by corrosion will not be honored as a materials defect claim. It is the user's responsibility to provide suitable protection against corrosive agents such as moisture and condensation and other harmful elements. If the IP rating of the fixture should be higher than IP20, the design of the housing should be according to the IP standards in the application. LINEARlight LM01B 16.11.2012 Seite 3 von 4 www.osram.com Assembly Information In order to optimize the thermal management the metal surface needs to be clean (dirt and oil free) and planar for the best contact with the LED module. To connect one module, the feeder LM-2PIN-500 must be plugged in the "INPUT" side of the module. for two or more modules, the "OUTPUT"-side of the first module must be connected with the "INPUT"-side of following module via LM-2CONN, LM-2CONN-50. Please connect more boards as described above. Ordering Guide Product group Product EAN* LINEARlight 2700K LM01B-W3F-827 4008321 845054 LINEARlight 4000K LM01B-W3F-840 LM01B W3F 840 4008321 846204 10 LINEARlight 5700K LM01B-W3F-857 4008321 846280 10 LINEARlight Blue LM01B-B2 4008321 845078 10 CONNECTsystem LM-2PIN-500 4008321908629 500 CONNECTsystem LM-2CONN 4008321 908643 500 CONNECTsystem LM-2CONN-50 4008321 908667 500 *) EAN: Ordering number per single module; S-Unit: Modules per shipping unit Note: Typical performance data are subject to change without any further notice, particularly as LED technology evolves. LINEARlight LM01B 16.11.2012 Seite 4 von 4 S-Unit* 10