STLUX Digital controllers for lighting and power conversion applications with up to 6 programmable PWM generators, 96 MHz PLL, DALI Datasheet - production data Features Up to 6 programmable PWM generators (SMEDs - “State Machine Event Driven”) – 10 ns event detection and reaction – Max.1.3 ns PWM resolution – Single, coupled and two coupled operational modes – Up to 3 internal/external events per SMED DALI (digital addressable lighting interface) – Interrupt driven hardware encoder – Bus frequency: 1.2, 2.4 or 4.8 kHz – IEC 60929 and IEC 62386 compliant plus 24-bit frame extension – Configurable noise rejection filter – Reverse polarity on Tx/Rx lines 4 analog comparators – 4 internal 4-bit references – 1 external reference – Less than 50 ns propagation time – Continuous comparison cycle ADCs (up to 8 channels) – 10-bit precision, with operational amplifier to extend resolution to 12-bit equivalent – Sequencer functionality – Input impedance: 1 M – Configurable gain value: x1 and x4 Integrated microcontroller – Advanced STM8® core with Harvard architecture and 3-stage pipeline – Max. fCPU: 16 MHz – Multiple low power modes May 2015 This is information on a product in full production. Memories – Flash and E2PROM with read while write (RWW) and error correction code (ECC) – Program memory: 32 Kbytes Flash; data retention 15 years at 85 °C after 10 kcycles at 25 °C – Data memory: 1 Kbyte true data E2PROM; data retention:15 years at 85 °C after 100 kcycles at 85 °C – RAM: 2 Kbytes Clock management – Internal 96 MHz PLL – Low power oscillator circuit for external crystal resonator or direct clock input – Internal, user-trimmable 16 MHz RC and low power 153.6 kHz RC oscillators – Clock security system with clock monitor Basic peripherals – System and auxiliary timers – IWDG/WWDG watchdog, AWU, ITC I/O – GPIO with highly robust design, immune against current injection – Fast digital input DIGIN, with configurable pull-up Communication interfaces – UART asynchronous with SW flow control and boot loader support – I2C master/slave fast-slow speed rate Operating temperature: -40 °C up to 105 °C Table 1. Device summary Part number Package STLUX385A, STLUX383A TSSOP38 STLUX325A VFQFPN32 STLUX285A TSSOP28 DocID027870 Rev 1 1/126 www.st.com Contents STLUX Contents 1 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 2 STLUX family features list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 3 Introducing SMED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 4 System architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 5 Product overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 5.1 SMED (state machine event driven): configurable PWM generator . . . . . 15 5.1.1 SMED coupling schemes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 5.1.2 Connection matrix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Connection matrix interconnection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 5.2 5.3 5.4 5.5 2/126 Internal controller (CPU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 5.2.1 Architecture and registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 5.2.2 Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 5.2.3 Instruction set . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 5.2.4 Single wire interface module (SWIM) . . . . . . . . . . . . . . . . . . . . . . . . . . 20 5.2.5 Debug module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Basic peripherals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 5.3.1 Vectored interrupt controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 5.3.2 Timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Flash program and data E2PROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 5.4.1 Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 5.4.2 Write protection (WP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 5.4.3 Protection of user boot code (UBC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 5.4.4 Readout protection (ROP) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Clock controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 5.5.1 Internal 16 MHz RC oscillator (HSI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 5.5.2 Internal 153.6 kHz RC oscillator (LSI) . . . . . . . . . . . . . . . . . . . . . . . . . . 25 5.5.3 Internal 96 MHz PLL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 5.5.4 External clock input/crystal oscillator (HSE) . . . . . . . . . . . . . . . . . . . . . 25 DocID027870 Rev 1 STLUX 6 7 Contents 5.6 Power management . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 5.7 Communication interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 5.7.1 Digital addressable lighting interface (DALI) . . . . . . . . . . . . . . . . . . . . . 26 5.7.2 Universal asynchronous receiver/transmitter (UART) . . . . . . . . . . . . . . 27 5.7.3 Inter-integrated circuit interface (I2C) . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 5.8 Analog-to-digital converter (ADC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 5.9 Analog comparators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Pinout and pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 6.1 Pinout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 6.2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 6.3 Input/output specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 I/O multifunction signal configuration . . . . . . . . . . . . . . . . . . . . . . . . . 35 7.1 Multifunction configuration policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 7.2 Port P0 I/O multifunction configuration signal . . . . . . . . . . . . . . . . . . . . . 35 7.3 7.4 7.5 7.2.1 Alternate function P0 configuration signals . . . . . . . . . . . . . . . . . . . . . . 35 7.2.2 Port P0 diagnostic signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 7.2.3 Port P0 I/O functional multiplexing signal . . . . . . . . . . . . . . . . . . . . . . . 37 7.2.4 P0 interrupt capability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 7.2.5 P0 programmable pull-up and speed feature . . . . . . . . . . . . . . . . . . . . 37 Port P1 I/O multifunction configuration signal . . . . . . . . . . . . . . . . . . . . . 38 7.3.1 Port P1 I/O multiplexing signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 7.3.2 P1 programmable pull-up feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Port P2 I/O multifunction configuration signal . . . . . . . . . . . . . . . . . . . . . 39 7.4.1 P2 interrupt capability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 7.4.2 P2 programmable pull-up feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 Multifunction Port configuration registers . . . . . . . . . . . . . . . . . . . . . . . . . 41 MSC_IOMXP0 (Port P1 I/O MUX control register). . . . . . . . . . . . . . . . . . . . . . . . . 41 MSC_IOMXP1 (Port P1 I/O MUX control register). . . . . . . . . . . . . . . . . . . . . . . . . 42 MSC_IOMXP2 (Port P2 I/O MUX control register). . . . . . . . . . . . . . . . . . . . . . . . . 43 MSC_INPP2AUX1 (INPP aux register) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 8 Memory and register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 8.1 Memory map overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 8.2 Register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 DocID027870 Rev 1 3/126 126 Contents STLUX 8.2.1 General purpose I/O GPIO0 register map . . . . . . . . . . . . . . . . . . . . . . . 46 8.2.2 General purpose I/O GPIO1 register map . . . . . . . . . . . . . . . . . . . . . . . 46 8.2.3 Miscellaneous registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 8.2.4 Flash and E2PROM non-volatile memories . . . . . . . . . . . . . . . . . . . . . . 49 8.2.5 Reset register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 8.2.6 Clock and clock controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 8.2.7 WWDG timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 8.2.8 IWDG timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 8.2.9 AWU timers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 8.2.10 Inter-integrated circuit interface (I2C) . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 8.2.11 Universal asynchronous receiver/transmitter (UART) . . . . . . . . . . . . . . 52 8.2.12 System timer registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 8.2.13 Auxiliary timer registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 8.2.14 Digital addressable lighting interface (DALI) . . . . . . . . . . . . . . . . . . . . . 53 8.2.15 DALI noise rejection filter registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 8.2.16 Analog-to-digital converter (ADC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 8.2.17 State machine event driven (SMEDs) . . . . . . . . . . . . . . . . . . . . . . . . . . 55 8.2.18 CPU register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 8.2.19 Global configuration register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 8.2.20 Interrupt controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 8.2.21 SWIM control register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 9 Interrupt table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 10 Option bytes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60 10.1 Option byte register overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 10.2 Option byte register description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 ROP (memory readout protection register) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 UBC (UBC user boot code register). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 nUBC (UBC user boot code register protection) . . . . . . . . . . . . . . . . . . . . . . . . . . 70 GENCFG (general configuration register) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 nGENCFG (general configuration register protection) . . . . . . . . . . . . . . . . . . . . . . 71 MISCUOPT (miscellaneous configuration register) . . . . . . . . . . . . . . . . . . . . . . . . 71 nMISCUOPT (miscellaneous configuration register protection). . . . . . . . . . . . . . . 72 CLKCTL (CKC configuration register) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 nCLKCTL (CKC configuration register protection) . . . . . . . . . . . . . . . . . . . . . . . . . 73 HSESTAB (HSE clock stabilization register) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 4/126 DocID027870 Rev 1 STLUX Contents nHSESTAB (HSE clock stabilization register protection). . . . . . . . . . . . . . . . . . . . 73 WAITSTATE (Flash wait state register) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 nWAITSTATE (Flash wait state register protection) . . . . . . . . . . . . . . . . . . . . . . . 74 AFR_IOMXP0 (alternative Port0 configuration register) . . . . . . . . . . . . . . . . . . . . 75 nAFR_IOMXP0 (alternative Port0 configuration register protection) . . . . . . . . . . . 75 AFR_IOMXP1 (alternative Port1 configuration register) . . . . . . . . . . . . . . . . . . . . 76 nAFR_IOMXP1 (alternative Port1 configuration register protection) . . . . . . . . . . . 76 AFR_IOMXP2 (alternative Port2 configuration register) . . . . . . . . . . . . . . . . . . . . 77 nAFR_IOMXP2 (alternative Port2 configuration register protection) . . . . . . . . . . . 77 MSC_OPT0 (miscellaneous configuration reg0) . . . . . . . . . . . . . . . . . . . . . . . . . . 78 nMSC_OPT0 (miscellaneous configuration reg0 protection) . . . . . . . . . . . . . . . . . 78 OPTBL (option byte bootloader) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 nOPTBL (option byte boot loader protection). . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 11 12 Device identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 11.1 Unique ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 11.2 Device ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 12.1 Parameter conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 12.1.1 Minimum and maximum values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 12.1.2 Typical values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 12.1.3 Typical curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 12.1.4 Typical current consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 12.1.5 Loading capacitors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 12.1.6 Pin output voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 12.2 Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 12.3 Operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 12.3.1 VOUT external capacitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 12.3.2 Supply current characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 12.3.3 External clock sources and timing characteristics . . . . . . . . . . . . . . . . . 96 12.3.4 Internal clock sources and timing characteristics . . . . . . . . . . . . . . . . . 99 12.3.5 Memory characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 12.3.6 I/O port pin characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 12.3.7 Typical output level curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 12.3.8 Reset pin characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 12.3.9 I2C interface characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 DocID027870 Rev 1 5/126 126 Contents STLUX 12.3.10 10-bit SAR ADC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 12.3.11 Analog comparator characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 12.3.12 DAC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 12.4 EMC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116 12.4.1 Electrostatic discharge (ESD) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 12.4.2 Static latch-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 13 Thermal characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 14 Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118 14.1 TSSOP38 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .118 14.2 VFQFPN32 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 14.3 TSSOP28 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122 15 STLUX development environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 16 Order codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 17 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 6/126 DocID027870 Rev 1 STLUX List of tables List of tables Table 1. Table 2. Table 3. Table 4. Table 5. Table 6. Table 7. Table 8. Table 9. Table 10. Table 11. Table 12. Table 13. Table 14. Table 15. Table 16. Table 17. Table 18. Table 19. Table 20. Table 21. Table 22. Table 23. Table 24. Table 25. Table 26. Table 27. Table 28. Table 29. Table 30. Table 31. Table 32. Table 33. Table 34. Table 35. Table 36. Table 37. Table 38. Table 39. Table 40. Table 41. Table 42. Table 43. Table 44. Table 45. Table 46. Table 47. Table 48. Device summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 STLUX features list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Connection matrix interconnection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 Multifunction configuration registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 P0 internal multiplexing signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 Port P1 I/O multiplexing signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 Port P2 I/O multiplexing signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40 MSC_IOMXP0 (Port P1 I/O MUX control register) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 MSC_IOMXP1 (Port P1 I/O MUX control register) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42 MSC_IOMXP2 (Port P2 I/O MUX control register) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43 MSC_INPP2AUX1 (INPP aux register) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44 Internal memory map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 General purpose I/O GPIO0 register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 General purpose I/O GPIO1 register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46 Miscellaneous direct register address mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47 Miscellaneous indirect register address mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48 Non-volatile memory register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 RST_SR register map. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49 Clock and clock controller register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 WWDG timer register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 IWDG timer register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 AWU timer register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51 I2C register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 UART register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 System timer register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 Auxiliary timer register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 DALI register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 DALI filter register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 ADC register map and reset value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 SMED register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55 CPU register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 CFG_GCR register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56 Interrupt software priority register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 SWIM register map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57 Interrupt vector exception table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58 Option byte register overview - STLUX385A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61 Option byte register overview - STLUX383A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63 Option byte register overview - STLUX325A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65 Option byte register overview - STLUX285A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67 ROP (memory readout protection register). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 UBC (UBC user boot code register) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69 nUBC (UBC user boot code register protection). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 GENCFG (general configuration register) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 nGENCFG (general configuration register protection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 MISCUOPT (miscellaneous configuration register) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71 nMISCUOPT (miscellaneous configuration register protection) . . . . . . . . . . . . . . . . . . . . . 72 CLKCTL (CKC configuration register) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72 DocID027870 Rev 1 7/126 126 List of tables Table 49. Table 50. Table 51. Table 52. Table 53. Table 54. Table 55. Table 56. Table 57. Table 58. Table 59. Table 60. Table 61. Table 62. Table 63. Table 64. Table 65. Table 66. Table 67. Table 68. Table 69. Table 70. Table 71. Table 72. Table 73. Table 74. Table 75. Table 76. Table 77. Table 78. Table 79. Table 80. Table 81. Table 82. Table 83. Table 84. Table 85. Table 86. Table 87. Table 88. Table 89. Table 90. Table 91. Table 92. Table 93. Table 94. Table 95. Table 96. Table 97. Table 98. Table 99. Table 100. 8/126 STLUX nCLKCTL (CKC configuration register protection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 HSESTAB (HSE clock stabilization register) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73 nHSESTAB (HSE clock stabilization register protection) . . . . . . . . . . . . . . . . . . . . . . . . . . 73 WAITSTATE (Flash wait state register) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 nWAITSTATE (Flash wait state register) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74 AFR_IOMXP0 (alternative Port0 configuration register) . . . . . . . . . . . . . . . . . . . . . . . . . . . 75 nAFR_IOMXP0 (alternative Port0 configuration register protection) . . . . . . . . . . . . . . . . . 75 AFR_IOMXP1 (alternative Port1 configuration register) . . . . . . . . . . . . . . . . . . . . . . . . . . . 76 nAFR_IOMXP1 (alternative Port1 configuration register protection) . . . . . . . . . . . . . . . . . 76 AFR_IOMXP2 (alternative Port2 configuration register) . . . . . . . . . . . . . . . . . . . . . . . . . . . 77 nAFR_IOMXP2 (alternative Port2 configuration register protection) . . . . . . . . . . . . . . . . . 77 MSC_OPT0 (miscellaneous configuration reg0). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78 nMSC_OPT0 (miscellaneous configuration reg0 protection) . . . . . . . . . . . . . . . . . . . . . . . 78 OPTBL (option byte bootloader) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 nOPTBL (option byte boot loader protection) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79 Unique ID register overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Dev ID register overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 Device revision model overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81 Voltage characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 Current characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84 Thermal characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 General operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 Operating conditions at power-up/power-down . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 Supply base current consumption at VDD/VDDA = 3.3/5 V . . . . . . . . . . . . . . . . . . . . . . . . . 88 Supply low power consumption at VDD/VDDA = 3.3/5 V . . . . . . . . . . . . . . . . . . . . . . . . . . . 89 Peripheral supply current consumption at VDD/VDDA = 3.3 V . . . . . . . . . . . . . . . . . . . . . . 90 Peripheral supply current consumption at VDD/VDDA = 5 V . . . . . . . . . . . . . . . . . . . . . . . . 92 Wake-up times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 HSE user external clock characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96 HSE crystal/ceramic resonator oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 HSI RC oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 LSI RC oscillator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 PLL internal source clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99 Flash program memory/data E2PROM memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 Voltage DC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101 Current DC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102 Operating frequency characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 102 NRST pin characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 I2C interface characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109 ADC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 ADC accuracy characteristics at VDD/VDDA 3.3 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111 ADC accuracy characteristics at VDD/VDDA 5 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 112 Analog comparator characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 DAC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 115 ESD absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 Electrical sensitivity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116 Package thermal characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117 TSSOP38 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119 VFQFPN32 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 TSSOP28 package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123 Ordering information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125 DocID027870 Rev 1 STLUX List of figures List of figures Figure 1. Figure 2. Figure 3. Figure 4. Figure 5. Figure 6. Figure 7. Figure 8. Figure 9. Figure 10. Figure 11. Figure 12. Figure 13. Figure 14. Figure 15. Figure 16. Figure 17. Figure 18. Figure 19. Figure 20. Figure 21. Figure 22. Figure 23. Figure 24. Figure 25. Figure 26. Figure 27. Figure 28. Figure 29. Figure 30. Figure 31. Figure 32. Figure 33. Figure 34. Figure 35. Figure 36. Figure 37. Figure 38. Figure 39. STLUX internal design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Internal block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Coupled SMED overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 SMED subsystem overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 STLUX285A SMED subsystem overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Flash and E2PROM internal memory organizations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 TSSOP38 pinout of STLUX385A and STLUX383A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 VFQFPN32 pinout of STLUX325A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 TSSOP28 pinout of STLUX285A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31 Port P0 I/O functional multiplexing scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 Port P1 I/O multiplexing scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Supply current measurement conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 Pin loading conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 Pin input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 External capacitor CVOUT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 PWM current consumption with fSMED = PLL fPWM = 0.5 MHz at VDD/VDDA = 5 V. . . . . . . 94 PWM current consumption with fSMED = PLL fPWM = 0.5 MHz at VDD/VDDA = 5 V. . . . . . . 94 PWM current consumption with fSMED = HSI fPWM = 0.5 MHz at VDD/VDDA = 3.3 V . . . . . 95 PWM current consumption with fSMED = HSI fPWM = 0.5 MHz at VDD/VDDA = 5 V . . . . . . . 95 HSE external clock source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 HSE oscillator circuit diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 VOH standard pad at 3.3 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 VOL standard pad at 3.3 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103 VOH standard pad at 5 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 VOL standard pad at 5 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104 VOH fast pad at 3.3 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 VOL fast pad at 3.3 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 105 VOH fast pad at 5 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 VOL fast pad at 5 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106 VOH high speed pad at 3.3 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107 VOL high speed pad at 3.3 V. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107 VOH high speed pad at 5 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 VOL high speed pad at 5 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108 ADC equivalent input circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 113 ADC conversion accuracy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 114 TSSOP38 package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118 VFQFPN32 package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 TSSOP28 package outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 122 STLUX development tools workflow . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124 DocID027870 Rev 1 9/126 126 Description 1 STLUX Description The STLUX™ family of controllers is a part of the STMicroelectronics® digital devices tailored for lighting and power conversion applications. The STLUX controllers have been successfully integrated in a wide range of architectures and applications, starting from simple buck converters for driving multiple LED strings, boost for power factor corrections, half-bridge resonant converters for high power dimmable LED strings and up to full bridge controllers for HID lamp ballasts. 10/126 DocID027870 Rev 1 STLUX 2 STLUX family features list STLUX family features list The devices of the STLUX family provide the following features: Table 2. STLUX features list Device Feature list STLUX385A STLUX383A STLUX325A STLUX285A Package TSSOP38 TSSOP38 VFQFPN32 TSSOP28 Pin count 38 38 32 28 SMED numbers 6 6 6 6 SMED PWM output pins 6 6 5 4 Fast digital inputs pins 6 6 5(1) 3(2) Positive comparator input pin 4 4 4 2(3) Negative comparator input pins 1 1 1 1(3) Yes Yes Yes Yes Internal DACs 4 4 4 4 ADC input pins 8 8 6 8 x1 - x4 x1 x1 x1 GPIO Port 0 pins 6 6 4 4 UART peripheral Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes System timer 1 1 1 1 Auxiliary timer 1 1 1 1 Auto-wakeup timer 1 1 1 1 Watchdog Window watchdog timer 1 1 1 1 Independent watchdog timer 1 1 1 1 Flash program memory 32 Kbytes 32 Kbytes 32 Kbytes 32 Kbytes EEPROM data memory 1 Kbytes 1 Kbytes 1 Kbytes 1 Kbytes RAM (bytes) 2 Kbytes 2 Kbytes 2 Kbytes 2Kbytes SWIM pin Dedicated Dedicated Mixed Dedicated DALI peripheral ADC gain I 2C peripheral HSE function Timers 1. DIGIN2 - DIGIN3 are connected to the same pin. 2. DIGIN0-DIGIN1 are connected on the same pin; DIGIN2-DIGIN3 are connected to the same pin; DIGIN4 - DIGIN5 are connected to the same pin. 3. CPP0, CPP1 and CPM3 are connected on the same pin; CPP2 and CPP3 are connected to the same pin. DocID027870 Rev 1 11/126 126 Introducing SMED 3 STLUX Introducing SMED The heart of the STLUX family is the SMED (state machine event driven) technology which allows the device to pilot six independently configurable PWM clocks with a maximum resolution of 1.3 ns. A SMED is a powerful autonomous state machine, which is programmed to react to both external and internal events and may evolve without any software intervention. The SMED reaction time can be as low as 10.4 ns, giving the STLUX the ability of operating in time critical applications. The SMED offers superior performance when compared to traditional, timer based, PWM generators. Each SMED is configured via the STLUX internal microcontroller. The integrated controller extends the STLUX reliability and guarantees more than 15 years of both operating lifetime and memory data retention for program and data memory after cycling. A set of dedicated peripherals complete the STLUX: 4 analog comparators with configurable references and 50 ns max. propagation delay. It is ideal to implement zero current detection algorithms or detect current peaks. 10-bit ADC with configurable op amp and 8-channel sequencer. DALI: hardware interface that provides full IEC 60929 and IEC 62386 slave interface. 96 MHz PLL for high output signal resolution. Documentation This datasheet contains the description of features, pinout, pin assignment, electrical characteristics, mechanical data and ordering information. 12/126 For information on programming, erasing and protection of the internal Flash memory, please refer to the STM8S reference in the programming manual “How to program STM8S and STM8A Flash program memory and data EEPROM” (PM0051). For information on the debug and SWIM (single wire interface module) refer to the “STM8 SWIM communication protocol and debug module” user manual (UM0470). For information on the STM8 core, please refer to the “STM8 CPU programming manual” (PM0044). For information on the SMED configurator please refer to the “STLUX™ SMED configurator 1.0" user manual (UM1760). For information on the STLUX385A peripheral library please refer to the “Description of STLUX385A peripheral library” user manual (UM1753). For information on the STLUX385A examples kit please refer to the “Description of STLUX385A examples kit” user manual (UM1763). DocID027870 Rev 1 STLUX 4 System architecture System architecture The STLUX devices family generates and controls PWM signals by means of a state machine, called SMED (state machine event driven). Figure 1 gives an overview of the internal architecture. Figure 1. STLUX internal design The core of the device is the SMED unit: a hardware state machine driven by system events. The SMED includes 4 states (S0, S1, S2 and S3) available during running operations. A special HOLD state is provided as well. The SMED allows the user to configure, for every state, which system events will trigger a transaction to a new state. During a transaction from one state to the other, the PWM output signal level can be updated. Once a SMED is configured and running, it becomes an autonomous unit, so no interaction is required since the SMED automatically reacts to system events. Thanks to the SMED's 96 MHz operating frequency and their automatic dithering function, the PWM maximum resolution is 1.3 ns. The STLUX family has 6 SMEDs available. Multiple SMEDs can operate independently from each other or they can be grouped together to form a more powerful state machine. The STLUX also integrates a low power STM8 microcontroller which is used to configure and monitor the SMED activity and to supply external communication such as the DALI. The STM8 controller has full access to all the STLUX subsystems, including the SMEDs. The STLUX family also features a sequential ADC, which can be configured to continuously sample up to 8 channels. Section : Block diagram illustrates the overall system block and shows how SMEDs have been implemented in the STLUX architecture. DocID027870 Rev 1 13/126 126 System architecture STLUX Block diagram Figure 2. Internal block diagram 1. The number of channels depends on the specific STLUX device. 14/126 DocID027870 Rev 1 STLUX 5 Product overview Product overview Section 5.1 describes the features implemented in the product device. 5.1 SMED (state machine event driven): configurable PWM generator The SMED is an advanced programmable PWM generator signal. The SMED (state machine event driven) is a state machine device controllable by both external events (primary I/O signals) and internal events (counter timers), which generates an output signal (PWM) depending on the evolution of the internal state machine. The PWM signal generated by the SMED is therefore shaped by external events and not only by a simple timer. This mechanism allows to generate controlled high frequency PWM signals. The SMED is also autonomous: once it has been configured by the STLUX internal controller, the SMED can operate without any software interaction. The STLUX family provides 6 SMED units. Multiple SMEDs can operate independently from each other or they can be grouped together to form a more powerful state machine. The main features of a SMED are described here below: 5.1.1 Configurable state machine generating a PWM signal More than 10.4 ns PWM native resolution Up to 1.3 ns PWM resolution when using SMED dithering 6 states available in each SMED: IDLE, S0, S1, S2, S3 plus a special HOLD state Transactions triggered by synchronous and asynchronous external events or an internal timer Each transaction can generate an interrupt Fifteen registers available to configure the state machine behavior Four 16-bit configurable time registers, one for each running state (T0, T1, T2, T3) Internal resources accessible through the processor interface Eight interrupt request lines SMED coupling schemes The SMED coupling extends the capability of the single SMED, preserving the independence of each “Finite State Machine” (FSM) programmed state evolution. The coupling scheme allows the SMED pulse signals to be interleaved on their own PWM or on a merged single PWM output. The STLUX supports the following coupled configuration schemes: Single SMED configuration Synchronous coupled SMEDs Asynchronous coupled SMEDs Synchronous two coupled SMEDs Asynchronous two coupled SMEDs External controlled SMED DocID027870 Rev 1 15/126 126 Product overview STLUX The SMED units may be configured in different coupled schemes through the SMDx_GLBCONF and SMDx_DRVOUT bit fields of MSC_SMEDCFGxy registers. An outline of the SMED subsystem is shown in Figure 3. Figure 3. Coupled SMED overview 1. The PWM5 output pin is not present on the STLUX325A. 2. The PWM4 and PWM5 output pins are not present on the STLUX285A. 5.1.2 Connection matrix The connection matrix extends the input connectivity of each SMED unit so that a SMED can receive events from a wide range of sources. Through the matrix, it's possible to connect the SMED inputs to various signal families such as digital inputs, comparator output signals, SW events, and three PWM internal feedback signals as shown in Figure 4. The list of the available event sources is the following: DIGIN [5:0]: digital input lines CMP [3:0]: analog comparator outputs PWM [5:0]: output signals of SMEDs (only PWM 0, 1 and 5 are accessible) SW [5:0]: software events Figure 4 shows the connection matrix and signal interconnections as they are implemented in the STLUX family. 16/126 DocID027870 Rev 1 STLUX Product overview Figure 4. SMED subsystem overview DocID027870 Rev 1 17/126 126 Product overview STLUX Figure 5. STLUX285A SMED subsystem overview Connection matrix interconnection Every SMED unit has three input selection lines, one for each In_Sig input, configurable via the MSC_CBOXS (5:0) register. The selection lines choose the interconnection between one of possible four connection matrix signals for each SMED input event In_Sig (Y). Table 3 shows the layout of the connection matrix interconnection signals as implemented in the STLUX family. 18/126 DocID027870 Rev 1 STLUX Product overview Table 3. Connection matrix interconnection Conb_s(x)_(y)(z) SMED number SMED input (x) (y) 00 01 10 11 0 CP0 DIG0 DIG2 DIG5 1 CP1 DIG0 DIG3 CP3 2 CP2 DIG1 DIG4 SW0 0 CP1 DIG1 DIG3 DIG0 1 CP2 DIG1 DIG4 CP3 2 CP0 DIG2 DIG5 SW1 0 CP2 DIG2 DIG4 DIG1 1 CP0 DIG2 DIG5 PWM0 2 CP1 DIG3 DIG0 SW2 0 CP0 DIG3 DIG5 DIG2 1 CP1 DIG3 DIG0 PWM1 2 CP2 DIG4 DIG1 SW3 0 CP1 DIG4 DIG0 DIG3 1 CP2 DIG4 DIG1 PWM5 2 CP0 DIG5 DIG2 SW4 0 CP2 DIG5 DIG1 DIG4 1 CP0 DIG5 DIG2 CP3 2 CP1 DIG0 DIG3 SW5 0 1 2 3 4 5 SMED input signal selection (z) Connection matrix legend: Note: X represents the SMED [5:0] number Y represents the SMED input signal number (In_Sig [2:0]) Z represents the In_Sig (Y) selection signal Each SMED input has independent connection matrix selection signals. The DIG2 and DIG3 signals are interconnected together, the pin DIGIN [3_2] on the STLUX325A. On STLUX285A DIG0 and DIG1 signals are interconnected together, to the pin DIGIN [1_0], DIG2 and DIG3 signals are interconnected together, to the pin DIGIN [3_2] and DIG4 and DIG5 signals are interconnected together, to the pin DIGIN [5_4] DocID027870 Rev 1 19/126 126 Product overview 5.2 STLUX Internal controller (CPU) The STLUX family integrates a programmable STM8 controller acting as a device supervisor. The STM8 is a modern CISC core and has been designed for code efficiency and performance. It contains 21 internal registers (six of them directly addressable in each execution context), 20 addressing modes including indexed indirect and relative addressing and 80 instructions. 5.2.1 Architecture and registers 5.2.2 5.2.3 5.2.4 Harvard architecture with 3-stage pipeline 32-bit wide program memory bus with single cycle fetching for most instructions X and Y 16-bit index registers, enabling indexed addressing modes with or without offset and read-modify-write type data manipulations 8-bit accumulator 24-bit program counter with 16-Mbyte linear memory space 16-bit stack pointer with access to a 64-Kbyte stack 8-bit condition code register with seven condition flags updated with the results of last executed instruction Addressing 20 addressing modes Indexed indirect addressing mode for lookup tables located in the entire address space Stack pointer relative addressing mode for efficient implementation of local variables and parameter passing Instruction set 80 instructions with 2-byte average instruction size Standard data movement and logic/arithmetic functions 8-bit by 8-bit multiplication 16-bit by 8-bit and 16-bit by 16-bit division Bit manipulation Data transfer between the stack and accumulator (push/pop) with direct stack access Data transfer using the X and Y registers or direct memory-to-memory transfers Single wire interface module (SWIM) The single wire interface module (SWIM), together with the integrated debug module (DM), permits non-intrusive, real-time in-circuit debugging and fast memory programming. The interface can be activated in all device operation modes and can be connected to a running device (hot plugging).The maximum data transmission speed is 145 byte/ms. The SWIM pin is a multifunction signal. For further details refer to Table 8: Port P2 I/O multiplexing signal in Section 7.4 on page 39. 20/126 DocID027870 Rev 1 STLUX 5.2.5 Product overview Debug module The non-intrusive debugging module is fully controllable by the external target emulator. Besides memory and peripheral operation, the CPU operation can also be monitored in real-time by means of shadow registers. 5.3 R/W of RAM and peripheral registers in real-time R/W for all resources when the application is stopped Breakpoints on all program memory instructions (software breakpoints), except for the interrupt vector table Two advanced breakpoints and 23 predefined breakpoint configurations Basic peripherals Section 5.3.1 and Section 5.3.2 describe the basic peripherals accessed by the internal CPU controller. 5.3.1 5.3.2 Vectored interrupt controller Nested interrupts with three software priority levels 21 interrupt vectors with hardware priority Two vectors for 12 external maskable or un-maskable interrupt request lines Trap and reset interrupts Timers The STLUX family provides several timers which are used by software and do not interact directly with the SMED and the PWM generation. System timers The system timer consists of a 16-bit autoreload counter driven by a programmable prescaled clock and operating in one shoot or free running operating mode. The timer is used to provide the IC time base system clock, with an interrupt generation on timer overflow events. Auxiliary timer The auxiliary timer is a light timer with elementary functionality. The time base frequency is provided by the CCO clock logic (configurable with a different source clock and prescale division factors), while the interrupt functionality is supplied by an interrupt edge detection logic similarly to the solution adopted for the Port P0/P2. The timer has the following main features: Free running mode Up counter Timer prescaler 8-bit Interrupt timer capability: – Vectored interrupt – Interrupt IRQ/NMI or polling mode Timer pulse configurable as a clock output signal via the CCO primary pin DocID027870 Rev 1 21/126 126 Product overview STLUX Thanks to the great configurability of the CCO frequency, the timer can cover a wide range of interval time to fit better the target application requirements. Auto-wakeup timer The AWU timer is used to cyclically wake-up the IC device from the active halt state. The AWU frequency time base fAWU can be selected between the following clock sources: LSI (153.6 kHz) and the external clock HSE scaled down to 128-kHz clock. By default the fAWU clock is provided by the LSI internal source clock. Watchdog timers The watchdog system is based on two independent timers providing a high level of robustness to the applications. The watchdog timer activity is controlled by the application program or by suitable option bytes. Once the watchdog is activated, it cannot be disabled by the user program without going through reset. Window watchdog timer The window watchdog is used to detect the occurrence of a software fault, usually generated by external interferences or by unexpected logical conditions, which causes the application program to break the normal operating sequence. The window function can be used to adjust the watchdog intervention period in order to match the application timing perfectly. The application software must refresh the counter before timeout and during a limited time window. If the counter is refreshed outside this time window, a reset is issued. Independent watchdog timer The independent watchdog peripheral can be used to resolve malfunctions due to hardware or software failures. It is clocked by the 153.6 kHz LSI internal RC clock source. By properly setting the hardware watchdog feature associated option bits, the watchdog is automatically enabled at poweron, and generates a reset unless the key register is written by software before the counter reaches the end of the count. 5.4 Flash program and data E2PROM Embedded Flash and E2PROM with the memory ECC code correction and protection mechanism preventing embedded program hacking. 22/126 32 Kbyte of single voltage program Flash memory 1 Kbyte true (not emulated) data E2PROM Read while write: writing in the data memory is possible while executing code program memory The device setup is stored in a user option area in the non-volatile memory. DocID027870 Rev 1 STLUX 5.4.1 Product overview Architecture Figure 6. Flash and E2PROM internal memory organizations 5.4.2 The memory is organized in blocks of 128 bytes each Read granularity: 1 word = 4 bytes Write/erase granularity: 1 word (4 bytes) or 1 block (128 bytes) in parallel Writing, erasing, word and block management is handled automatically by the memory interface. Write protection (WP) Write protection in application mode is intended to avoid unintentional overwriting of the memory. The write protection can be removed temporarily by executing a specific sequence in the user software. 5.4.3 Protection of user boot code (UBC) In all STLUX devices a memory area of 32 Kbyte can be protected from overwriting at a user option level. In addition to the standard write protection, the UBC protection can be modified by the embedded program or via a debug interface when the ROP protection is enabled. The UBC memory area contains the reset and interrupt vectors and its size can be adjusted in increments of 512 bytes by programming the UBC and nUBC option bytes. Note: If users choose to update the boot code in the application programming (IAP), this has to be protected so to prevent unwanted modification. DocID027870 Rev 1 23/126 126 Product overview 5.4.4 STLUX Readout protection (ROP) The STLUX family provides a readout protection of the code and data memory which can be activated by an option byte setting. The readout protection prevents reading and writing program memory, data memory and option bytes via the debug module and SWIM interface. This protection is active in all device operation modes. Any attempt to remove the protection by overwriting the ROP option byte triggers a global erase of the program and data memory contents. 5.5 Clock controller The clock controller distributes the system clock provided by different oscillators to the core and the peripherals. It also manages clock gating for low power modes and ensures clock robustness. The main clock controller features are: 5.5.1 Clock sources Internal 16-MHz and 153.6-kHz RC oscillators External source clock: – Crystal/resonator oscillator – External clock input Internal PLL at 96 MHz (not used as the fMASTER source clock) Reset: after the reset the microcontroller restarts by default with the HSI internal clock scaled at 2 MHz (16 MHz/8). The clock source and speed can be changed by the application program as soon as the code execution starts. Safe clock switching: clock sources can be changed safely on the fly in run mode through a configuration register. The clock signal is not switched until the new clock source is ready. The design guarantees glitch-free switching. Clock management: to reduce power consumption, the clock controller can stop the clock to the core or individual peripherals. Wakeup: in case the device wakes up from low power modes, the internal RC oscillator (16 MHz/8) is used for a quick startup. After a stabilization time, the device brings back the clock source that was selected before Halt mode was entered. Clock security system (CSS): the CSS permits monitoring of external clock sources and automatic switching to the internal RC (16 MHz/8) in case of a clock failure. Configurable main clock output (CCO): this feature permits to output an internal clock source signal for application usage. Internal 16 MHz RC oscillator (HSI) The high speed internal (HSI) clock is the default master clock line, generated by an internal RC oscillator and with nominal frequency of 16 MHz. It has the following major features: 24/126 RC architecture Glitch-free oscillation 3-bit user calibration circuit. DocID027870 Rev 1 STLUX 5.5.2 Product overview Internal 153.6 kHz RC oscillator (LSI) The low speed internal (LSI) clock is a low speed clock line provided by an internal RC circuit. It drives both the independent watchdog (IWDG) circuit and the auto-wakeup unit (AWU). It can also be used as a low power clock line for the master clock fMASTER. 5.5.3 Internal 96 MHz PLL The PLL provides a high frequency 96 MHz clock used to generate high frequency and accurate PWM waveforms. The input reference clock must be 16 MHz and may be sourced either by the internal HSI signal or by the external HSE auxiliary input crystal oscillator line. The internal PLL prescaled clock cannot be selected as fMASTER. Note: When the application requires a PWM signal with a custom defined long term stability, it is suggested to use an external clock source connected to the HSE auxiliary clock line as a PLL input reference clock. In this case, the external clock source accuracy determines the PWM output stability. 5.5.4 External clock input/crystal oscillator (HSE) The high speed external clock (HSE) allows the connection of an external clock generated, for example, by a highly accurate crystal oscillator. The HSE is interconnected with the fMASTER clock line and to several peripherals. It allows users to provide a custom clock characterized by a high level of precision and stability to meet the application requirements. The HSE supports two possible external clock sources with a maximum of 24 MHz: Crystal/ceramic resonator interconnected with the HseOscin/HseOscout signals Direct drive clock interconnected with the HseOscin signal The HseOscin and HseOscout signals are multifunction pins configurable through the I/O multiplex mechanism; for further information refer to Section 7: I/O multifunction signal configuration on page 35. Note: When the HSE is configured as the fMASTER source clock, the HSE input frequency cannot be higher than 16 MHz. When the HSE is the PLL input reference clock, then the HSE input frequency must be equal to 16 MHz. If the HSE is the reference for the SMED or the ADC logic, the input frequency can be configured up to 24 MHz. 5.6 Power management For efficient power management, the application can be put in one of four different low power modes. Users can configure each mode to obtain the best compromise between the lowest power consumption, the fastest startup time and available wakeup sources. Wait mode: in this mode, the CPU is stopped, but peripherals are kept running. The wakeup is triggered by an internal or external interrupt or reset. Active halt mode with regulator on: in this mode, the CPU and peripheral clocks are stopped. An internal wakeup is generated at programmable intervals by the autowakeup unit (AWU). The main voltage regulator is kept powered on, so current consumption is higher than in the active halt mode with the regulator off, but the DocID027870 Rev 1 25/126 126 Product overview STLUX wakeup time is faster. The wakeup is triggered by the internal AWU interrupt, external interrupt or reset. Active halt mode with regulator off: this mode is the same as active halt with the regulator on, except that the main voltage regulator is powered off, so the wakeup time is slower. Halt mode: in this mode the microcontroller uses the least power. The CPU and peripheral clocks are stopped, while the main voltage regulator is switched in poweroff. Wakeup is triggered by an external event or reset. In all modes the CPU and peripherals remain permanently powered on, the system clock is applied only to selected modules. The RAM content is preserved and the brownout reset circuit remains enabled. 5.7 Communication interfaces 5.7.1 Digital addressable lighting interface (DALI) The DALI (digital addressable lighting interface), standardized as the IEC 62386, is the new interface for lighting control solutions defined by the lighting industry. The DALI protocol is generally implemented in a DALI communication module (DCM): a serial communication circuit designed for controllable electronic ballasts. “Ballast” is a device or circuit used to provide the required starting voltage and operating current for the LED, fluorescent, mercury or other electronic-discharge lamps. The STLUX DALI driver has the following characteristics: Speed line:1.2, 2.4 and 4.8 kHz transmission rate ± 10% Forward payload: 16, 17, 18 and 24-bit message length Backward payload: 8-bit message length. Bidirectional communications Monitor receiver line timeout 500 ms ± 10% Polarity insensitive on DALI_rx, DALI_tx signal line Interoperability with different message length Maskable interrupt request line DALI peripheral clock has slowed down to 153.6 kHz in low speed operating mode Improved DALI noise rejection filter on DALI_rx input line (see Section : DALI noise rejection filter). DALI noise rejection filter The STLUX DALI interface includes a noise rejection filter interconnected on the RX channel capable to remove any bounce, glitch or spurious pulse from the RX line. The filter can be configured via three registers: 26/126 MSC_DALICKSEL: selects the source clock of filter timing MSC_DALICKDIV: configures the clock prescaler value MSC_DALICONF: configures the filter count and operating mode. DocID027870 Rev 1 STLUX 5.7.2 Product overview Universal asynchronous receiver/transmitter (UART) UART is the asynchronous receiver/transmitter communication interface. SW flow control operating mode Full duplex, asynchronous communications High precision baud rate generator system Programmable data word length (8 or 9-bit) Configurable stop bit - support for 1 or 2 stop bit Configurable parity control Separate enable bits for transmitter and receiver Interrupt sources: – 5.7.3 Common programmable transmit and receive baud rates up to fMASTER/16 – Transmit events – Receive events – Error detection flags 2 interrupt vectors: – Transmitter interrupt – Receiver interrupt Reduced power consumption mode Wakeup from mute mode (by idle line detection or address mark detection) 2 receiver wakeup modes: – Address bit (MSB) – Idle line. Inter-integrated circuit interface (I2C) The I2C (inter-integrated circuit) bus interface serves as an interface between the microcontroller and the serial I2C bus. It provides a multimaster capability, and controls all I2C bus-specific sequencing, protocol, arbitration and timing. It supports standard and fast speed modes. Parallel-bus/I2C protocol converter Multimaster capability: the same interface can act as master or slave I2C master features: – Clock generation – Start and stop generation 2 I C slave features: – Programmable I2C address detection – Stop bit detection Generation and detection of 7-bit/10-bit addressing and general call Supports different communication speeds: – Standard speed (up to 100 kHz) – Fast speed (up to 400 kHz) DocID027870 Rev 1 27/126 126 Product overview Status flags: – Transmitter/receiver mode flag – End of byte transmission flag – I2C busy flag Error flags: – Arbitration lost condition for master mode – Acknowledgment failure after address/ data transmission – Detection of misplaced start or stop condition – Overrun/underrun if clock stretching is disabled Interrupt sources: – Communication interrupt – Error condition interrupt – Wakeup from Halt interrupt Wakeup capability: – 5.8 STLUX MCU wakes up from low power mode on address detection in slave mode. Analog-to-digital converter (ADC) The STLUX family includes a 10-bit successive approximation ADC with 8 multiplexed input channels. The analog input signal can be amplified before conversion by a selectable gain of 1 or 4(a) times. The analog-to-digital converter can operate either in single or in continuous/circular modes. The ADC unit has the following main features: 8/6 ADC input channel(b) 10-bit resolution Single and continuous conversion mode Independent or fixed channel gain value x1 or x4 to extend dynamic range and resolution to 12-bit equivalent(a) Interrupt events: – EOC interrupt asserted on end of conversion cycle – EOS interrupt asserted on end of conversion sequences – SEQ_FULL_EN interrupt assert on sequencer buffer full ADC input voltage range dependent on selected gain value(b) Selectable conversion data alignment Individual registers for up to 8 successive conversions. a. The gain x4 is available only on the STLUX385A. b. The number of ADC input channels depends of the STLUX device part number. 28/126 DocID027870 Rev 1 STLUX 5.9 Product overview Analog comparators The STLUX devices family includes four independent fast analog comparator units (COMP3-0). Each comparator has an internal reference voltage. The COMP3 can be also configured to use an external reference voltage connected to the CPM3 input pin. Each comparator reference voltage is generated by a dedicated internal-only 4-bit DAC unit. The main characteristics of the analog comparator unit (ACU) are the following: Each comparator has an internally configurable reference Internal reference voltages configurable in 16 steps with the 83 mV voltage grain from 0 V (GND) to 1.24 V (voltage reference) Two stage comparator architecture is used to reach a high gain Comparator output stage value accessible from processor interface Continuous fast cycle comparison time. DocID027870 Rev 1 29/126 126 Pinout and pin description STLUX 6 Pinout and pin description 6.1 Pinout Figure 7. TSSOP38 pinout of STLUX385A and STLUX383A 30/126 DocID027870 Rev 1 STLUX Pinout and pin description Figure 8. VFQFPN32 pinout of STLUX325A Figure 9. TSSOP28 pinout of STLUX285A DocID027870 Rev 1 31/126 126 Pinout and pin description 6.2 STLUX Pin description Table 4. Pin description Pin number TyTSSOP VFQFPN TSSOP pe 38 32 28 Main function Alternate function 1 Alternate Alternate function 2 function 3 I/O GPIO1[0]/PWM[0] SMED PWM channel 0 General purpose I/O 10 - - I/O DIGIN[0]/CCO_clk Digital input 0 Configurable clock output signal (CCO) - - I DIGIN[1] Digital input 1 - - - 1 21 2 22 3 23 4 24 3 I/O GPIO1[1]/PWM[1] SMED PWM channel 1 General purpose I/O 11 - - 5 25 4 I/O GPIO1[2]/PWM[2] SMED PWM channel 2 General purpose I/O 12 - - 26(1) 5 I DIGIN[2] Digital input 2 - - - I DIGIN[3] Digital input 3 - - - 8 - - I/O GPIO1[5]/PWM[5] SMED PWM channel 5 General purpose I/O 15 - - 9 27 6 I/O SWIM SWIM data interface General purposeI/O 06(2) - - 10 28 7 I/O NRST Reset - - - 11 29 8 PS VDD Digital and I/O power supply - - - 12 30 9 PS VSS Digital and I/O ground - - - 13 31 10 PS VOUT 1.8 V regulator capacitor - - - 14 32 11 I/O GPIO0[4]/Dali_TX/ I2C_sda/Uart_TX General purpose I/O 04 DALI data transmit I2C data UART data transmit 15 1 12 I/O GPIO0[5]/Dali_RX/ I2C_scl/Uart_RX General purpose I/O 05 DALI data receive I2C clock UART data receive 16 2 - I/O GPIO1[4]/PWM[4] SMED PWM channel 4 General purpose I/O 14 - - 17 3 I/O DIGIN[4]/I2C_sda Digital input 4 I2C data(3) - - 18 4 I/O DIGIN[5]/I2C_scl Digital input 5 I2C clock(3) - - 19 5 I/O GPIO1[3]/PWM[3] SMED PWM channel 3 General purpose I/O 13 - - 6 7 32/126 1 Pin name 2 13 14 DocID027870 Rev 1 STLUX Pinout and pin description Table 4. Pin description (continued) Pin number TyTSSOP VFQFPN TSSOP pe 38 32 28 20 6 Pin name Main function Alternate function 1 Alternate Alternate function 2 function 3 Output crystal oscillator signal UART data transmit I C clock Input crystal oscillator signal /input clock signal UART data receive 15 GPIO0[2]/I2C_sda/ I/O HseOscout/Uart_TX General purpose I/O 02 I2C data GPIO0[3]/I2C_scl/ I/O HseOscin/Uart_RX General purpose I/O 03 2 21 7 16 22 - - I/O GPIO0[0]/Uart_TX/ I2C_sda General purpose I/O 00 UART data transmit I2C data - 23 - - I/O GPIO0[1]/Uart_RX/ I2C_scl General purpose I/O 01 UART data receive I2C clock - 24 8 I CPP[3] Positive analog comparator input 3 - - - 17 25 9 I CPP[2] Positive analog comparator input 2 - - - 26 10 I CPM3 Negative analog comparator input 3 - - - 18 27 11 I CPP[1] Positive analog comparator input 1 - - - 28 12 I CPP[0] Positive analog comparator input 0 - - - 29 13 19 PS VDDA Analog power supply - - - 30 14 20 PS VSSA Analog ground - - - 31 - 21 I ADCIN[7] Analog input 7 - - - 32 - 22 I ADCIN[6] Analog input 6 - - - 33 15 23 I ADCIN[5] Analog input 5 - - - 34 16 24 I ADCIN[4] Analog input 4 - - - 35 17 25 I ADCIN[3] Analog input 3 - - - 36 18 26 I ADCIN[2] Analog input 2 - - - 37 19 27 I ADCIN[1] Analog input 1 - - - 38 20 28 I ADCIN[0] Analog input 0 - - - 1. The DIGIN3 and DGIN2 are connected together on the STLUX325A, DIGIN [3_2] pin. 2. Available only on the STUX325A. 3. Not available on the STUX285A. DocID027870 Rev 1 33/126 126 Pinout and pin description 6.3 STLUX Input/output specifications The STLUX family includes three different I/O types: Normal I/Os configurable either at 2 or 10 MHz maximum frequency Fast I/O operating up to 12 MHz. High speed I/O operating up to 32 MHz The STLUX I/Os are designed to withstand current injection. For a negative injection current of 4 mA, the resulting leakage current in the adjacent input does not exceed 1 µA; further details are available in Section 12: Electrical characteristics on page 82. 34/126 DocID027870 Rev 1 STLUX 7 I/O multifunction signal configuration I/O multifunction signal configuration Several I/Os have multiple functionalities selectable through the configuration mechanism described from Section 7.1 to Section 7.5 on page 41. The STLUX I/Os are grouped into four different configurable ports: P0, P1, P2 and P3. 7.1 Multifunction configuration policy The STLUX supports either a cold or warm multifunction signal configuration policy according to the content of the EN_COLD_CFG bit field, a part of the GENCFG option byte register. When the EN_COLD_CFG bit is set, the cold configuration is selected and the multifunction signals are configured according to the values stored in the option bytes; otherwise when the EN_COLD_CFG bit is cleared (default case), the warm configuration mode is chosen and the multifunction pin functionality is configured through the miscellaneous registers. The configuration options and the proper configuration registers are detailed in Table 5: Table 5. Multifunction configuration registers EN_COLD_CFG Configuration policy Multifunction configuration registers 1 Cold AFR_IOMXP0, AFR_IOMXP1 and AFR_IOMXP2 0 (default) Warm MSC_IOMXP0, MSC_IOMXP1 and MSC_IOMXP2 The warm configuration is volatile, thus not maintained after a device reset. 7.2 Port P0 I/O multifunction configuration signal The Port P0 multiplexes several input/output functionalities, increasing the device flexibility. The P0 port pins can be independently assigned to general purpose I/Os or to internal peripherals. All communication peripherals and the external oscillator are hosted by the Port P0 pins. In order to avoid electrical conflicts on the user application board, the P0 signals are configured at reset as GPIO0 inputs without pull-up resistors. Once the reset is released, the firmware application must initialize the inputs with the proper configuration according to the application needs. 7.2.1 Alternate function P0 configuration signals The multifunction pins can be configured via one of the following two registers, depending on the overall configuration policy (warm/cold): Cold configuration: AFR_IOMXP0 option byte registers (refer to Section 10: Option bytes on page 60). After the reset the P0 signals are configured in line with AFR_IOMXP0 contents. Warm configuration: MSC_IOMXP0 miscellaneous register (refer to Section 7.5 on page 41). After the reset, the P0 signals are configured as GPIO input lines with the pull-up disabled. DocID027870 Rev 1 35/126 126 I/O multifunction signal configuration STLUX Table 6 summarizes the Port P0 configuration scheme. Both registers MSC_IOMXP0 and AFR_IOMXP0 use the same register fields Sel_p054, Sel_p032 and Sel_p010 which respectively control the bits [5, 4], [3, 2] and [1, 0] of the Port P0. Table 6. P0 internal multiplexing signals(1) Port P0 multifunction configuration signal MUX selection Port pins Multifunction signal Selection fields P0[1,0](2) GPIO0 [1] GPIO0 [0] UART_rx UART_tx I2C_scl I2C_sda 00 Sel_P010 RFU reserved encoding P0[3,2] P0[5,4] Value (binary) 01 10 11 GPIO0 [3] GPIO0 [2] 2C_scl I2C_sda HseOscin HseOscout UART_rx UART_tx 11 GPIO0[5] GPIO0[4] 00 DALI_rx DALI_tx 2C_scl I2C_sda UART_rx UART_tx I I 00 Sel_P032 Sel_P054 01 10 01 10 11 1. The Sel_p054, Sel_p032, Sel_p010 are register fields for both registers MSC_IOMXP0 and AFR_IOMXP0. The peripheral conflict (same resources selected on different pins at the same time) has to be prevented by SW configuration. When the I2C interface is selected either on the GPIO0 [5:4] GPIO0 [3:2] or on GPIO0 [1:0] signals the related I/O port speed has to be configured at 10 MHz by programming the GPIO0 internal peripheral. 2. Available only on the STLUX385A and STLUX383A. 7.2.2 Port P0 diagnostic signals The primary I/Os can be used to trace the SMED's state evolution. This feature allows the debug of the complex SMED configurations. The trace selection can be enabled or disabled via the register MSC_IOMXSMD. The diagnostic signal selection through the MSC_IOMXSMD register overrides the functional configuration of the MSC_IOMXP0 register. The Port P0 [5:3] or P0 [2:0] can be configured to output one or two different SMEDs' current states. The SMEDs FSM state signals (coded on three bits) may be multiplexed either on port bits P0 [5:3] or P0 [2:0]; alternatively two different SMEDs signal states can be traced simultaneously on the same port bits. The SMED trace configuration is forbidden on the Port P [2:0] when the external comparator reference voltage is programmed on the Port P0 [1, 0]. The Port 0 I/O signal availability depends on the STLUX device. 36/126 DocID027870 Rev 1 STLUX 7.2.3 I/O multifunction signal configuration Port P0 I/O functional multiplexing signal Figure 10 shows an outline view of the Port P0 multifunction multiplexing scheme. Figure 10. Port P0 I/O functional multiplexing scheme Note: Where the “A/F(s) in” and “A/F(s) out” signals are defined in Section 6.2 on page 32. Verify pin availability in Table 4: Pin description on page 32. On the STLUX325A device: P0_ODR [1:0] bits must be keep clear. P0 [6] is a multifunction signal configurable through the MSC_IOMXP2 [7] and AFR_IOMXP2 [7] register bits - for further details refer to Section 7.4. Port P0 [6] signal is controlled by P0_ODR [6] and P0_IDR [6] GPIO0 registers. On the STLUX285A device: 7.2.4 P0_ODR [1:0] bits must be keep clear. P0 interrupt capability Port P0 signals may be configured to generate maskable (IRQ) and un-maskable (NMI) interrupts by programming the MSC_CFGP0<n> and the MSC_STSP0 registers (n = index port signal). This functionality is not applicable to the bit port P0 [6] on the STLUX325A and on the port P0:[1:0] on STLUX285A. The interrupt request may be configured to wake-up the IC device from the WFI (wait for interrupt), AHalt (active Halt) and Halt power saving state. 7.2.5 P0 programmable pull-up and speed feature The I/O speed and pad pull-up resistance (47 k) of the port P0 may be configured through the GPIO0 internal registers. The pull-up resistance of the multifunction signal P0 [6] is always enabled on the STLUX325A. DocID027870 Rev 1 37/126 126 I/O multifunction signal configuration 7.3 STLUX Port P1 I/O multifunction configuration signal The Port P1 I/O multifunction pins, similarly to the Port P0, can be individually configured through the following set of registers based on the selected device configuration policy: Cold configuration: AFR_IOMXP1 option byte register (refer to Section 10 on page 60). After reset the P1 signals are configured in line with AFR_IOMXP1 contents. Warm configuration: MSC_IOMXP1 miscellaneous register (refer to Section 7.5). After reset the P1 signals are configured as PWM output lines. Every Port1 I/O can be configured to operate as a PWM output pin or a GPIO. Differently from the port P0s, the pins are configured as PWM output signals by default after reset. Table 7 summarizes the Port P1 configurations as selected by the register fields Sel_p15 … Sel_p10 which respectively control the bits [5] … [0] of the Port P1 (verify resources availability in Table 4 on page 32). Table 7. Port P1 I/O multiplexing signal(1) Port P1 multifunction configuration signal MUX selection Output signal Multifunction signal Selection bits P1[0] P1[1] P1[2] P1[3] P1[4] P1[5] PWM[0] GPIO1[0] PWM[1] GPIO1[1] PWM[2] GPIO1[2] PWM[3] GPIO1[3] PWM[4] GPIO1[4] PWM[5] GPIO1[5] Sel_P10 Sel_P11 Sel_P12 Sel_P13 Sel_P14 Sel_P15 Value (binary) 1 0 1 0 1 0 1 0 1 0 1 0 1. The Sel_p15…Sel_p10 are common register fields of both registers MSC_IOMXP1 and AFR_IOMXP1. In cold configuration the P1x are configured as defined by the AFR_IOMXP1 option byte. The PWM default polarity level is configured by the register option byte GENCFG. Verify pin availability in Table 4 on page 32. 38/126 DocID027870 Rev 1 STLUX 7.3.1 I/O multifunction signal configuration Port P1 I/O multiplexing signal Figure 11 shows an outline view of the port P1 signal multiplexing scheme. Figure 11. Port P1 I/O multiplexing scheme Note: The P1 [5:0] output signals may be read back from the P1_IDR register only when the pins are configured as GPIO out or PWM signals. The PWM internal signal is read back also by its own SMED through the SMD<n>_FSM_STS register. Verify pin availability in device pin Table 4 on page 32. 7.3.2 P1 programmable pull-up feature The pad pull-up resistances (47 k) of the Port1 may be configured through the GPIO1 internal register. 7.4 Port P2 I/O multifunction configuration signal The Port2 I/O multifunction pins, similarly to the Port0 and Port2, can be individually configured through the following set of registers based on the selected device configuration policy: Cold configuration: AFR_IOMXP2 option byte registers (refer to Section 10: Option bytes on page 60. After reset the P2 signals are configured in line with AFR_IOMXP2 contents. Warm configuration: MSC_IOMXP2 miscellaneous register (refer to Section 7.5). After reset the P2 signals are configured as DIGIN input lines with the pull-up enabled. Table 8 summarizes the port P2 configurations selected by the register fields Sel_p25…Sel_p20 which respectively control the bits [5]… [0] of port P2. The P2 [0] is configured by the CCOEN bit field of the register CKC_CCOR. The SWIM alternate function signal (when available) is controlled by the Sel_SWIM bit field provided by registers AFR_IOMXP2 [7] and MSC_IOMXP2 [7]. DocID027870 Rev 1 39/126 126 I/O multifunction signal configuration STLUX Table 8. Port P2 I/O multiplexing signal Port P2 multifunction configuration signal MUX selection Output signal Multifunction signal Selection bits P2[0] P2[4] P2[5] SWIM Note: DIGIN[0] CCO DIGIN[4] I2 C_sda DIGIN[5] I2C_scl GPIO0[6] SWIM Value (binary) CCOEN Sel_P254 Sel_P254 Sel_SWIM 0 1 1 0 1 0 0 X The Sel_P254 is a common register field of both registers MSC_IOMXP2 and AFR_IOMXP2. The peripheral conflict (same resources selected on different pins at the same time) has to be prevented by SW configuration. The signal ports P2 [3:1] are exclusively interconnected with DIGIN [3:1] primary pins. When the I2C i/f is selected on DIGIN [5:4] signals the I/O speed is auto-configured at 10 MHz and the internal pull-up functionality is controlled by the MSC_INPP2AUX1 register. The GPIO0 [6] signal is selected when both Sel_SWIM = '0' and CFG_GCR [0] = '1'. SWIM signal function is selected when the CFG_GCR [0] = '0'. After reset by default the P2 [0] is configured as the DIGIN [0] signal. Verify pinout availability in Table 4: Pin description on page 32. The P2 [0] is configured by the CCOEN field of the CKC_CCOR register as shown in Table 8. 7.4.1 P2 interrupt capability Port P2 signals may be configured to generate maskable (IRQ) and un-maskable (NMI) interrupts by configuring the MSC_CFGP2<n> and the MSC_STSP2 registers (n = index port signal 0-5). The interrupt request may be configured to wake-up the IC device from the WFI (wait for interrupt), AHalt (active Halt) and Halt power saving state. 7.4.2 P2 programmable pull-up feature The pad pull-up resistances (47 k) of Port2 signals are individually controllable by the MSC_INPP2AUX1 register. 40/126 DocID027870 Rev 1 STLUX 7.5 I/O multifunction signal configuration Multifunction Port configuration registers MSC_IOMXP0 (Port P1 I/O MUX control register) Table 9. MSC_IOMXP0 (Port P1 I/O MUX control register) Offset: 0x2A Default value: 0x00 7 6 5 4 3 2 1 0 RFU Sel_P054 [1:0] Sel_P032 [1:0] Sel_P010 [1:0](1) r r/w r/w r/w 1. Not available on the STLUX325A and STLUX285A. The Port0 I/O multifunction signal configurations register (for functionality description refer to Section 7.2 on page 35). Verify pinout availability in Table 4: Pin description on page 32. Bit 1 - 0: Sel_P010 [1:0] Port0 [1:0] I/O multiplexing scheme: 00: Port0 [1:0] are interconnected to GPIO0 [1:0] signals 01: Port0 [1:0] are interconnected to UART_rx and UART_tx signals 10: Port0 [1:0] are interconnected to I2C_scl and I2C_sda signals 11: RFU Bit 3 - 2: Sel_P032 [1:0] Port0 [3:2] I/O multiplexing scheme: 00: Port0 [3:2] are interconnected to GPIO0 [3:2] signals 01: Port0 [3:2] are interconnected to I2C_scl and I2C_sda signals 10: Port0 [3:2] are interconnected to HseOscin and HseOscout analog signals 11: Port0 [3:2] are interconnected to UART_rx and UART_tx signals Bit 5 - 4: Sel_P054 [1:0] Port0 [5:4] I/O multiplexing scheme: 00: Port0 [5:4] are interconnected to GPIO0 [5:4] signals 01: Port0 [5:4] are interconnected to DALI_rx and DALI_tx signals 10: Port0 [5:4] are interconnected to I2C_scl and I2C_sda signals 11: Port0 [5:4] are interconnected to UART_rx and UART_tx signals Bit 7 - 6: RFU reserved; in order to guarantee future compatibility, the bits are kept or set to 0 during register write operations. DocID027870 Rev 1 41/126 126 I/O multifunction signal configuration STLUX MSC_IOMXP1 (Port P1 I/O MUX control register) Table 10. MSC_IOMXP1 (Port P1 I/O MUX control register) Offset: 0x2B Default value: 0x3F 7 6 RFU 5 4 Sel_P15(1) , (2) (1) Sel_P14 3 2 1 0 Sel_P13 Sel_P12 Sel_P11 Sel_P10 r r/w 1. Not available on the STLUX285A; these bits are set to 1 after reset, must be cleared by SW during the IC device initialization phase and during register write operations. 2. Not available on the STLUX325A; these bits are set to 1 after reset, must be cleared by SW during the IC device initialization phase and during register write operations. The Port1 I/O multifunction signal configuration register (for functionality description refer to Section 7.3 on page 38). Verify pinout availability in Table 4: Pin description on page 32. Bit 0: Sel_P10 Port1 [0] I/O multiplexing scheme: 0: Port1 [0] is interconnected to GPIO1 [0] signal 1: Port1 [0] is interconnected to PWM [0] signal Bit 1: Sel_P11 Port1 [1] I/O multiplexing scheme: 0: Port1 [1] is interconnected to GPIO1 [1] signal 1: Port1 [1] is interconnected to PWM [1] signal Bit 2: Sel_P12 Port1 [2] I/O multiplexing scheme: 0: Port1 [2] is interconnected to GPIO1 [2] signal 1: Port1 [2] is interconnected to PWM [2] signal Bit 3: Sel_P13 Port1 [3] I/O multiplexing scheme: 0: Port1 [3] is interconnected to GPIO1 [3] signal 1: Port1 [3] is interconnected to PWM [3] signal Bit 4: Sel_P14 Port1 [4] I/O multiplexing scheme: 0: Port1 [4] is interconnected to GPIO1 [4] signal 1: Port1 [4] is interconnected to PWM [4] signal Bit 5: Sel_P15 Port1 [5] I/O multiplexing scheme: 0: Port1 [5] is interconnected to GPIO1 [5] signal 1: Port1 [5] is interconnected to PWM [5] signal 42/126 DocID027870 Rev 1 STLUX I/O multifunction signal configuration Bit 7 - 6: RFU reserved; in order to guarantee future compatibility, the bits are kept or set to 0 during register write operations. MSC_IOMXP2 (Port P2 I/O MUX control register) Table 11. MSC_IOMXP2 (Port P2 I/O MUX control register) Offset: 0x13 (indirect area) Default value: 0xFF 7 6 5 4 3 2 1 Sel_SWIM RFU Sel_P254 RFU r/w r r/w r 0 The Port1 I/O multifunction signal configurations register (for functionality description refer to Section 7.5). This register is not available on STLUX285A and must be kept set to its default value Check device feature availability. Bit 3 - 0: RFU reserved; must be kept 0 during register writing for future compatibility Bit 4: Sel_P254 Port2 [5:4] I/O multiplexing scheme: 0: Port2 [5:4] are interconnected to I2C_scl and I2C_sda signals 1: Port2 [5:4] are interconnected to DIGIN [5:4] signals Bit 6 - 5: RFU reserved; in order to guarantee future compatibility, the bits are kept or set to 0 during register write operations. Bit 7: Sel_SWIM SWIM alternate function signal enable; this feature is active when the SWD field of the register CFG_GCR is set. 0: SWIM pin is configured with GPIO0 [6] signal. 1: SWIM functionality is preserved. DocID027870 Rev 1 43/126 126 I/O multifunction signal configuration STLUX MSC_INPP2AUX1 (INPP aux register) Table 12. MSC_INPP2AUX1 (INPP aux register) Offset: 0x08 (indirect area) Default value: 0x00 7 6 5 4 3 2 RFU INPP2_PULCTR [5:0] r r/w 1 0 Bit 5 - 0: INPP2_PULCTR [5:0].This register configures respectively the INPP2 [5:0] pull-up functionality as follows: 0: enable pad pull-up features (enabled by default for compatibility with the STLUX385) 1: disable pad pull-up Bit 7 - 6: RFU reserved; in order to guarantee future compatibility, the bits are kept or set to 0 during register write operations. Note: The MSC_IOMXP2 and MSC_INPP2AUX1 are addressable in indirect mode. On STLUX285A devices, due to DIGINs double bond interconnections the pull-up functionality must be configured in the same way for the two couple pins: 44/126 DIGIN10 is controlled by register field NPP2_PULCTR[1:0]. DIGIN32 is controlled by register field INPP2_PULCTR[3:2]. DIGIN54 is controlled by register field INPP2_PULCTR[5:4]. DocID027870 Rev 1 STLUX Memory and register map 8 Memory and register map 8.1 Memory map overview This section describes the register map implemented in the STLUX devices family. Table 13 shows the main memory map organization. All registers and memory spaces are configured within the first 64 Kbytes of memory, the remaining address spaces are kept reserved for the future use. Table 13. Internal memory map Address Description 00.0000h 2-kB RAM 00.07FFh Stack 00.0800h 00.3FFFh Reserved 00.4000h 00.43FFh 1 kB data E2PROM 00.4400h 00.47FFh Reserved 00.4800h 00.487Fh 128 option bytes 00.4880h 00.4FFFh Reserved 00.5000h 00.57FFh Peripheral register region 00.5800h 00.5FFFh Reserved 00.6000h 00.67FFh 2-kB boot ROM 00.6800h 00.7EFFh Reserved 00.7F00h 00.7FFFh Core register region 00.8000h 32 interrupt vectors 00.8080h 00.FFFFh 32-kB program Flash 01.0000h FF.FFFFh Reserved By default the stack address is initialized at 0x07FF and rolls over when it reaches the address value of 0x0400. DocID027870 Rev 1 45/126 126 Memory and register map 8.2 STLUX Register map Section 8.2.1 shows the STLUX memory map. 8.2.1 General purpose I/O GPIO0 register map Table 14. General purpose I/O GPIO0 register map Address Register name Register description 0x00.5000 P0_ODR Output data 0x00.5001 P0_IDR Input data P0_DDR Data direction 0x00.5003 P0_CR1 Control register 1 0x00.5004 P0_CR2 Control register 2 0x00.5002 8.2.2 Block GPIO0 General purpose I/O GPIO1 register map Table 15. General purpose I/O GPIO1 register map Address Register name Register description 0x00.5005 P1_ODR Output data 0x00.5006 P1_IDR Input data P1_DDR Data direction 0x00.5008 P1_CR1 Control register 1 0x00.5009 P1_CR2 Control register 2 0x00.5007 46/126 Block GPIO1 DocID027870 Rev 1 STLUX 8.2.3 Memory and register map Miscellaneous registers Direct register address mode Table 16. Miscellaneous direct register address mode Address Register name Register description 0x00.5010 MSC_CFGP00 P00 input line control(1) 0x00.5011 MSC_CFGP01 P01 input line control(1) 0x00.5012 MSC_CFGP02 P02 input line control 0x00.5013 MSC_CFGP03 P03 input line control 0x00.5014 MSC_CFGP04 P04 input line control 0x00.5015 MSC_CFGP05 P05 input line control 0x00.5016 MSC_CFGP20 P20 input line control 0x00.5017 MSC_CFGP21 P21 input line control 0x00.5018 MSC_CFGP22 P22 input line control 0x00.5019 MSC_CFGP23 P23 input line control 0x00.501A MSC_CFGP24 P24 input line control 0x00.501B MSC_CFGP25 P25 input line control 0x00.501C MSC_STSP0 Port0 status 0x00.501D MSC_STSP2 Port2 status 0x00.501E MSC_INPP2 Port2 read RFU Reserved for future use MSC_DACCTR Comparators and DAC configuration 0x00.5021 MSC_DACIN0 DAC0 input data 0x00.5022 MSC_DACIN1 DAC1 input data 0x00.5023 MSC_DACIN2 DAC2 input data 0x00.5024 MSC_DACIN3 DAC3 input data 0x00.5025 MSC_SMDCFG01 SMED 0 - 1 behavior 0x00.5026 MSC_SMDCFG23 SMED 2 - 3 behavior 0x00.5027 MSC_SMDCFG45 SMED 4 - 5 behavior 0x00.5028 MSC_SMSWEV SMED software events 0x00.5029 MSC_SMUNLOCK SMED unlock 0x00.502A MSC_CBOXS0 Connection matrix selection for SMED 0 0x00.502B MSC_CBOXS1 Connection matrix selection for SMED 1 0x00.502C MSC_CBOXS2 Connection matrix selection for SMED 2 0x00.502D MSC_CBOXS3 Connection matrix selection for SMED 3 0x00.502E MSC_CBOXS4 Connection matrix selection for SMED 4 0x00.502F MSC_CBOXS5 Connection matrix selection for SMED 5 0x00.501F 0x00.5020 Block MSC DocID027870 Rev 1 47/126 126 Memory and register map STLUX Table 16. Miscellaneous direct register address mode (continued) Address Register name Register description 0x00.5030 MSC_IOMXSMD SMED Trace multiplexing on port 0 0x00.5031 0x00.5035 RFU Reserved for future use 0x00.5036 MSC_CFGP15 Aux timer interrupt configuration 0x00.5037 MSC_STSP1 Aux timer interrupt status RFU Reserved for future use 0x00.5039 MSC_INPP3 Port 3 (COMP) read 0x00.503A MSC_IOMXP0 Port 0 alternate function MUX 0x00.503B MSC_IOMXP1 Port 1 alternate function MUX 0x00.503C MSC_IDXADD MSC indirect register 0x00.503D MSC_IDXDAT MSC indirect data 0x00.5038 Block MSC 1. Address not available for the STLUX285A and STLUX325A. Indirect register address mode Table 17. Miscellaneous indirect register address mode Address (IDX) Register name Register description 0x00 - 0x04 RFU Reserved for future use 0x05 MSC_DALICKSEL DALI clock selection 0x06 MSC_DALICKDIV DALI filter clock division factor MSC_DALICONF DALI filter mode configuration MSC_INPP2AUX1 INPP2 auxiliary configuration register 1 0x09 MSC_INPP2AUX2 INPP2 auxiliary configuration register 2 0x0A - 0x12 RFU Reserved for future use 0x13 MSC_IOMXP2 Port2 alternate function MUX register(1) 0x07 0x08 Block MSC (indirect) 1. Register not available for the STLUX285A. 48/126 DocID027870 Rev 1 STLUX 8.2.4 Memory and register map Flash and E2PROM non-volatile memories Table 18. Non-volatile memory register map Address Register name Register description 0x00.505A FLASH_CR1 Control register 1 0x00.505B FLASH_CR2 Control register 2 0x00.505C FLASH_nCR2 Control register 2 (protection) 0x00.505D FLASH_FPR Memory protection FLASH_nFPR Memory protection (complemented reg.) FLASH_IAPSR Flash status 0x00.5062 FLASH_PUKR Write memory protection removal key reg. 0x00.5063 RFU Reserved for future use 0x00.5064 FLASH_DUKR Write memory protection removal data 0x00.5071 FLASH_WAIT Time access wait-state reg. 0x00.505E 0x00.505F 8.2.5 Block MIF Reset register Table 19. RST_SR register map Address Block Register name Register description 0x00.50B3 RSTC RST_SR Reset control status DocID027870 Rev 1 49/126 126 Memory and register map 8.2.6 STLUX Clock and clock controller Table 20. Clock and clock controller register map Address Register name Register description 0x00.50B4 CLK_SMD0 SMED 0 clock configuration 0x00.50B5 CLK_SMD1 SMED 1 clock configuration 0x00.50B6 CLK_SMD2 SMED 2 clock configuration 0x00.50B7 CLK_SMD3 SMED 3 clock configuration 0x00.50B8 CLK_SMD4 SMED 4 clock configuration 0x00.50B9 CLK_SMD5 SMED 5 clock configuration 0x00.50BA RFU Reserved for future use 0x00.50BB RFU Reserved for future use 0x00.50BC RFU Reserved for future use 0x00.50BD RFU Reserved for future use 0x00.50BE CLK_PLLDIV PLL clock divisor 0x00.50BF CLK_AWUDIV AWU clock divisor 0x00.50C0 CLK_ICKR Internal clock control CLK_ECKR External clock control CLK_PLLR PLL control 0x00.50C3 CLK_CMSR Clock master 0x00.50C4 CLK_SWR Clock switch 0x00.50C5 CLK_SWCR Switch control 0x00.50C6 CLK_CKDIVR Clock dividers 0x00.50C7 CLK_PCKENR1 Peripherals clock enable 0x00.50C8 CLK_CSSR Clock security system 0x00.50C9 CLK_CCOR Configurable clock output 0x00.50CA CLK_PCKENR2 Peripherals clock enable 0x00.50CB RFU Reserved for future use 0x00.50CC CLK_HSITRIMR HSI calibration trimmer 0x00.50CD CLK_SWIMCCR SWIM clock division 0x00.50CE CLK_CCODIVR CCO divider 0x00.50CF CLK_ADCR ADC clock configuration 0x00.50C1 0x00.50C2 50/126 Block CKC DocID027870 Rev 1 STLUX 8.2.7 Memory and register map WWDG timers Table 21. WWDG timer register map Address 0x00.50D1 0x00.50D2 8.2.8 Block WWDG Register name Register description WWDG_CR Watchdog control WWDG_WR Watchdog window IWDG timers Table 22. IWDG timer register map Address Block 0x00.50E0 0x00.50E1 IWDG 0x00.50E2 8.2.9 Register name Register description IWDG_KR Watchdog key IWDG_PR Watchdog time base IWDG_RLR Watchdog counter value after reload AWU timers Table 23. AWU timer register map Address Block 0x00.50F0 0x00.50F1 AWU 0x00.50F2 DocID027870 Rev 1 Register name Register description AWU_CSR AWU control status AWU_APR AWU asynchronous prescaler buffer AWU_TBR AWU time base selection 51/126 126 Memory and register map 8.2.10 STLUX Inter-integrated circuit interface (I2C) Table 24. I2C register map Address Register name Register description 0x00.5210 I2C_CR1 I2C control register 1 0x00.5211 I2C_CR2 I2C control register 2 0x00.5212 I2C_FREQR I2C frequency register 0x00.5213 I2C_OARL I2C own add-low register 0x00.5214 I2C_OARH I2C own add-high register 0x00.5215 RFU Reserved for future use 0x00.5216 I2C_DR I2C data register I2C_SR1 I2C status register 1 0x00.5218 I2C_SR2 I2C status register 2 0x00.5219 I2C_SR3 I2C status register 3 0x00.521A I2C_ITR I2C interrupt 0x00.521B I2C_CCRL I2C clock control 0x00.521C I2C_CCRH I2C clock control 0x00.521D I2C_TRISER I2C rising edge 0x00.5217 8.2.11 Block I2C Universal asynchronous receiver/transmitter (UART) Table 25. UART register map Address Register name Register description 0x00.5230 UART_SR UART status 0x00.5231 UART_DR UART data 0x00.5232 UART_BRR1 UART baud rate div. mantissa [7:0] UART_BRR2 UART baud rate div. mantissa [11:8] SCIDIV FRACT [3:0] 0x00.5234 UART_CR1 UART control register 1 0x00.5235 UART_CR2 UART control register 2 0x00.5236 UART_CR3 UART control register 3 0x00.5237 UART_CR4 UART control register 4 0x00.5233 52/126 Block UART DocID027870 Rev 1 STLUX 8.2.12 Memory and register map System timer registers Table 26. System timer register map Address Register name Register description 0x00.5340 STMR_CR1 Control register 1 0x00.5341 STMR_IER Interrupt enable 0x00.5342 STMR_SR1 Status register 1 0x00.5343 STMR_EGR Event generation STMR_CNTH Counter high 0x00.5345 STMR_CNTL Counter low 0x00.5346 STMR_PSCL Prescaler low 0x00.5347 STMR_ARRH Autoreload high 0x00.5348 STMR_ARRL Autoreload low 0x00.5344 8.2.13 Block STMR Auxiliary timer registers Table 27. Auxiliary timer register map Address Block Register name Register description 0x00.5009 GPIO1 P1_CR2 Control register 2 MSC_CFGP15 P15 input line control MSC_STSP1 Port 1 status CLK_CCODIVR CCO clock dividers CLK_CCOR Configurable clock output 0x00.5036 0x00.5037 0x00.50C6 0x00.50C9 8.2.14 MSC CKC Digital addressable lighting interface (DALI) Table 28. DALI register map Address Register name Register description 0x00.53C0 DALI_CLK_L Data rate control 0x00.53C1 DALI_CLK_H Data rate control 0x00.53C2 DALI_FB0 Forward message 0x00.53C3 DALI_FB1 Forward message DALI_FB2 Forward message DALI_BD Backward message 0x00.53C6 DALI_CR Control 0x00.53C7 DALI_CSR Control and status register 0x00.53C8 DALI_CSR1 Control and status register 1 0x00.53C9 DALI_REVLN Control reverse signal line 0x00.53C4 0x00.53C5 Block DALI DocID027870 Rev 1 53/126 126 Memory and register map 8.2.15 STLUX DALI noise rejection filter registers Table 29. DALI filter register map 8.2.16 Address Offset 0x00.503C 0x05 0x00.503C 0x06 0x00.503C 0x07 Block MSC (indirect) Register name Register description MCS_DALICKSEL DALI clock selection MSC_DALICKDIV DALI filter clock division factor MSC_DALICONF DALI filter mode configuration Analog-to-digital converter (ADC) Table 30. ADC register map and reset value Address Register name Register description 0x00.5400 ADC_CFG Configuration 0x00.5401 ADC_SOC Start of conversion 0x00.5402 ADC_IER Interrupt enable 0x00.5403 ADC_SEQ Sequencer 0x00.5404 ADC_DATL_0 Low part data 0 converted 0x00.5405 ADC_DATH_0 High part data 0 converted 0x00.5406 ADC_DATL_1 Low part data 1 converted 0x00.5407 ADC_DATH_1 High part data 1 converted 0x00.5408 ADC_DATL_2 Low part data 2 converted 0x00.5409 ADC_DATH_2 High part data 2 converted ADC_DATL_3 Low part data 3 converted ADC_DATH_3 High part data 3 converted 0x00.540C ADC_DATL_4 Low part data 4 converted 0x00.540D ADC_DATH_4 High part data 4 converted 0x00.540E ADC_DATL_5 Low part data 5 converted 0x00.540F ADC_DATH_5 High part data 5 converted 0x00.5410 ADC_DATL_6 Low part data 6 converted 0x00.5411 ADC_DATH_6 High part data 6 converted 0x00.5412 ADC_DATL_7 Low part data 7 converted 0x00.5413 ADC_DATH_7 High part data 7 converted 0x00.5414 ADC_SR Status 0x00.5415 ADC_DLYCNT SOC delay counter 0x00.540A 0x00.540B 54/126 Block ADC DocID027870 Rev 1 STLUX 8.2.17 Memory and register map State machine event driven (SMEDs) The SMED<n> address register is: ADD_REG = (5500h + (40h) * n) + offset where <n> is the SMED instance number 0 - 5. Table 31. SMED register map Address (offset) Register name Register description 0x00 SMD<n>_CTR Control 0x01 SMD<n>_CTR_TMR Control time 0x02 SMD<n>_CTR_INP Control input 0x03 SMD<n>_CTR_DTR Dithering 0x04 SMD<n>_TMR_T0L Time T0 LSB 0x05 SMD<n>_TMR_T0H Time T0 MSB 0x06 SMD<n>_TMR_T1L Time T1 LSB 0x07 SMD<n>_TMR_T1H Time T1 MSB 0x08 SMD<n>_TMR_T2L Time T2 LSB 0x09 SMD<n>_TMR_T2H Time T2 MSB 0x0A SMD<n>_TMR_T3L Time T3 LSB 0x0B SMD<n>_TMR_T3H Time T3 MSB 0x0C SMD<n>_PRM_ID0 IDLE state parameter0 0x0D SMD<n>_PRM_ID1 IDLE state parameter1 SMD<n>_PRM_ID2 IDLE state parameter2 SMD<n>_PRM_S00 S0 state parameter0 0x10 SMD<n>_PRM_S01 S0 state parameter1 0x11 SMD<n>_PRM_S02 S0 state parameter2 0x12 SMD<n>_PRM_S10 S1 state parameter0 0x13 SMD<n>_PRM_S11 S1 state parameter1 0x14 SMD<n>_PRM_S12 S1 state parameter2 0x15 SMD<n>_PRM_S20 S2 state parameter0 0x16 SMD<n>_PRM_S21 S2 state parameter1 0x17 SMD<n>_PRM_S22 S2 state parameter2 0x18 SMD<n>_PRM_S30 S3 state parameter0 0x19 SMD<n>_PRM_S31 S3 state parameter1 0x1A SMD<n>_PRM_S32 S3 state parameter2 0x1B SMD<n>_CFG Timer configuration register 0x1C SMD<n>_DMP_L Counter dump LSB 0x1D SMD<n>_DMP_H Counter dump MSB 0x0E 0x0F Block SMED<n> DocID027870 Rev 1 55/126 126 Memory and register map STLUX Table 31. SMED register map (continued) Address (offset) Register name Register description 0x1E SMD<n>_GSTS General status 0x1F SMD<n>_IRQ Interrupt request register SMD<n>_IER Interrupt enable register SMD<n>_ISEL External events control 0x22 SMD<n>_DMP Dump enable 0x23 SMD<n>_FSM_STS FSM core status 0x20 0x21 8.2.18 Block SMED<n> CPU register Table 32. CPU register map Address Register name Register description 0x00.7F00 A Accumulator 0x00.7F01 PCE Program counter extended 0x00.7F02 PCH Program counter high 0x00.7F03 PCL Program counter low 0x00.7F04 XH X-index high XL X-index low 0x00.7F06 YH Y-index high 0x00.7F07 YL Y-index low 0x00.7F08 SPH Stack pointer high 0x00.7F09 SPL Stack pointer low 0x00.7F0A CC Code condition 0x00.7F05 Block CPU Note: Register space accessible in debug mode only. 8.2.19 Global configuration register Table 33. CFG_GCR register map 56/126 Address Block Register name Register description 0x00.7F60 GCR CFG_GCR Global configuration DocID027870 Rev 1 STLUX 8.2.20 Memory and register map Interrupt controller Table 34. Interrupt software priority register map Address Register name Register description 0x00.7F70 ITC_SPR0 Interrupt SW priority register 0 0x00.7F71 ITC_SPR1 Interrupt SW priority register 1 0x00.7F72 ITC_SPR2 Interrupt SW priority register 2 ITC_SPR3 Interrupt SW priority register 3 ITC_SPR4 Interrupt SW priority register 4 0x00.7F75 ITC_SPR5 Interrupt SW priority register 5 0x00.7F76 ITC_SPR6 Interrupt SW priority register 6 0x00.7F77 ITC_SPR7 Interrupt SW priority register 7 0x00.7F73 0x00.7F74 8.2.21 Block ITC SWIM control register Table 35. SWIM register map Address Block Register name Register description 0x00.7F80 SWIM SWIM_CSR SWIM control status 0x00.7F90 … 0x00.7F9B DM_BK1E DM … DM internal registers DM_VER DocID027870 Rev 1 57/126 126 Interrupt table 9 STLUX Interrupt table Table 36 shows the STLUX internal controller's interrupt vector. Table 36. Interrupt vector exception table Description Wakeup from Halt Wakeup from active halt Interrupt vector address RESET Reset Yes Yes 8000h TRAP Software interrupt 0 NMI NMI (not maskable interrupt) 1 AWU Auto-wakeup from Halt 2 CKC Clock controller Priority Source block 3 PO GPIO0 [5:0] external interrupts 4 AUXTIM Auxiliary timer 8004h Yes(1) Yes(1) 8008h Yes 800Ch 8010h (1), (2) Yes((1), (2) Yes(1), (2) Yes(1), (2) Yes 8014h 8018h 5 P2 DIGIN [5:0] external interrupts 6 SMED0 SMED-0 interrupt 8020h 7 SMED1 SMED-1 control logic 8024h 8 RFU(3) Reserved for future use 8028h 9 RFU (3) Reserved for future use 802Ch 10 RFU(3) Reserved for future use 8030h 11 RFU (3) Reserved for future use 8034h 12 RFU(3) Reserved for future use 8038h 13 RFU(3) Reserved for future use 803Ch 14 RFU (3) Reserved for future use 8040h 15 SMED2 SMED-2 control logic 8044h 16 SMED3 SMED-3 control logic 8048h 17 UART Tx complete 18 19 UART I2 C Receive register DATA FULL 2 I C interrupt 801Ch 804Ch Indirect (4) Indirect(4) 8050h Indirect (4) Yes 8054h 20 RFU(3) Reserved for future use 8058h 21 (3) Reserved for future use 805Ch RFU 22 ADC End of conversion 8060h 23 SYS-TMR Update/overflow 8064h 24 FLASH EOP/WR_PG_DIS 8068h Indirect(4) Indirect(4) 25 DALI DALI interrupt line 26 SMED4 SMED-4 control logic 8070h 27 SMED5 SMED-5 control logic 8074h 58/126 DocID027870 Rev 1 806Ch STLUX Interrupt table Table 36. Interrupt vector exception table (continued) Priority Source block Description Wakeup from Halt Wakeup from active halt Interrupt vector address 28 RFU(3) Reserved future use 8078h 29 (3) Reserved future use 807Ch RFU 1. The P [2, 0] [x] may be configured to generate a NMI requests. 2. The P [2, 0] [x] may be configured to generate an IRQ requests. 3. All RFU and unused interrupts should be initialized with 'IRET' for robust programming. 4. The P0 [x] may be configured to generate an IRQ and NMI request. DocID027870 Rev 1 59/126 126 Option bytes 10 STLUX Option bytes The user option byte is a memory E²PROM area allowing users to customize the IC device major functionalities: ROP: readout protection control field UBC: user boot code protection PWM: configurable reset output value WDG: internal watchdog HW configuration AFR: alternate multifunction signals configuration CKC: clock controller functionalities (PLL, HSE enable, AWU clock selection, etc.) HSE: clock stabilization counter WAIT: Flash and E²PROM wait state access time has to be configured with value 0x00 BOOT: configurable internal boot sources BL: bootloader control sequences Except the ROP byte all the other option bytes are stored twice in a regular (OPT) and complemented format (NOPT) for redundancy. The option byte can be programmed in ICP mode through the SWIM interface or in IAP mode by the application with the exception of the ROP byte that can be only configured via the SWIM interface. For further information about Flash programming refer to the programming manual “How to program STM8S and STM8A Flash program memory and data EEPROM” (PM0051). For information on SWIM programming procedures refer to the “STM8 SWIM communication protocol and debug module” user manual (UM0470). 60/126 DocID027870 Rev 1 Option byte register overview STLUX 10.1 Table 37. Option byte register overview - STLUX385A Option bits Address Option name 7 6 5 4 3 2 1 0 Default settings DocID027870 Rev 1 4800h ROP ROP[7:0] 00h 4801h UCB UBC[7:0] 00h 4802h nUCB nUBC[7:0] FFh 4803h GENCFG Rst_PWM5 Rst_PWM3 Rst_PWM2 Rst_PWM1 Rst_PWM0 COMP1_2 EN_COLD_CFG 00h 4804h nGENCFG nRst_PWM5 nRst_PWM4 nRst_PWM3 nRst_PWM2 nRst_PWM1 nRst_PWM0 nCOMP1_2 nEN_COLD_CFG FFh 4805h MISCUOPT - - 1 - LSI_EN IWdg_hw WWdg_hw WWDG_HALT 28h 4806h nMISCUOPT - - 0 - nLSI_EN nIWdg_hw nWWdg_hw nWWDG_HALT D7h 4807h CLKCTL - - - CKAWUSEL1 EXTCLK CKAWUSE L0 PRSC[1:0] 09h 4808h nCLKCTL - - - nCKAWUSEL1 nEXTCLK nCKAWUS EL0 nPRSC [1:0] F6h 4809h HSESTAB HSECNT[7:0] 00h 480Ah nHSESTAB nHSECNT[7:0] FFh RESERVED - 480Bh 480Ch Rst_PWM4 00h FFh WAITSTATE - - - - - - WaitStat [1:0] 00h 480Eh nWAITSTATE - - - - - - nWaitStat [1:0] FFh 480Fh AFR_IOMXP0 - - Sel_P054[1:0] Sel_P032[1:0] Sel_P010[1:0] 00h 4810h nAFR_IOMXP0 - - nSel_P054[1:0] nSel_P032[1:0] nSel_P010[1:0] FFh AFR_IOMXP1 AUXTMR - Sel_P15 Sel_P14 Sel_P13 Sel_P12 Sel_P11 Sel_P10 00h 4812h nAFR_IOMXP1 nAUXTMR - nSel_P15 nSel_P14 nSel_P13 nSel_P12 nSel_P11 nSel_P10 FFh AFR_IOMXP2 - - - Sel_P254 - - - - 10h 4814h nAFR_IOMXP2 - - - nSel_P254 - - - - EFh 4811h 4813h 61/126 Option bytes 480Dh Option bits Address Option name 7 6 5 4 3 2 1 0 Default settings 4815h MSC_OPT0 - - UARTLine [1:0] - - BootSel [1:0] 01h 4816h nMSC_OPT0 - - nUARTLine [1:0] - - nBootSe l[1:0] FEh RESERVED - - - - - - 00h 4817h 487Dh - - 487Eh OPTBL BL [7:0] 00h 487Fh nOPTBL nBL [7:0] FFh Note: Option bytes 62/126 Table 37. Option byte register overview - STLUX385A (continued) DocID027870 Rev 1 The default setting values refer to the factory configuration. The factory configuration can be overwritten by the user in accordance with the target application requirements. The factory configuration values are loosed after user programming fields or in case of the ROP unprotecting attempt causing a “Global Flash Erase”. The predefined initialized bit-values (1 or 0) must be preserved during memory writing. An undefined option bit must be keep 0 and the complement value at 1 during the memory writing sequence. STLUX Option bits Address Option name 7 6 5 4 3 2 1 0 Default settings DocID027870 Rev 1 4800h ROP ROP [7:0] 00h 4801h UCB UBC [7:0] 00h 4802h nUCB nUBC [7:0] FFh 4803h GENCFG Rst_PWM5 Rst_PWM3 Rst_PWM2 Rst_PWM1 EN_COLD_CFG 00h 4804h nGENCFG nRst_PWM5 nRst_PWM4 nRst_PWM3 nRst_PWM2 nRst_PWM1 nRst_PWM0 nCOMP1_2 nEN_COLD_CFG FFh 4805h MISCUOPT - - 1 - LSI_EN IWdg_hw WWdg_hw WWDG_HALT 28h 4806h nMISCUOPT - - 0 - nLSI_EN nIWdg_hw nWWdg_hw nWWDG_HALT D7h 4807h CLKCTL - - - CKAWUSEL1 EXTCLK CKAWUSE L0 PRSC[1:0] 09h 4808h nCLKCTL - - - nCKAWUSEL1 nEXTCLK nCKAWUS EL0 nPRSC[1:0] F6h 4809h HSESTAB HSECNT [7:0] 00h 480Ah nHSESTAB nHSECNT [7:0] FFh RESERVED - 480Bh 480Ch Rst_PWM4 Rst_PWM0 COMP1_2 00h FFh WAITSTATE - - - - - - WaitStat [1:0] 00h 480Eh nWAITSTATE - - - - - - nWaitStat [1:0] FFh 480Fh AFR_IOMXP0 - - Sel_P054 [1:0] Sel_P032 [1:0] Sel_P010 [1:0] 00h 4810h nAFR_IOMXP0 - - nSel_P054 [1:0] nSel_P032 [1:0] nSel_P010 [1:0] FFh 4811h AFR_IOMXP1 AUXTMR - Sel_P15 Sel_P14 Sel_P13 Sel_P12 Sel_P11 Sel_P10 3Fh 4812h nAFR_IOMXP1 nAUXTMR - nSel_P15 nSel_P14 nSel_P13 nSel_P12 nSel_P11 nSel_P10 C0h 4813h AFR_IOMXP2 - - - Sel_P254 - - - - 10h 4814h nAFR_IOMXP2 - - - nSel_P254 - - - - EFh 4815h MSC_OPT0 - - - - BootSel [1:0] 01h Option bytes 63/126 480Dh UARTLine [1:0] STLUX Table 38. Option byte register overview - STLUX383A Option bits Address 4816h 4817h 487Dh Option name 7 6 5 nMSC_OPT0 - - RESERVED - - 4 3 2 nUARTLine [1:0] - - - - - - 1 0 Default settings nBootSel [1:0] FEh - 00h - 487Eh OPTBL BL [7:0] 00h 487Fh nOPTBL nBL [7:0] FFh Note: Option bytes 64/126 Table 38. Option byte register overview - STLUX383A (continued) The default setting values refer to the factory configuration. The factory configuration can be overwritten by the user in accordance with the target application requirements. DocID027870 Rev 1 The factory configuration values are loosed after user programming fields or in case of the ROP unprotecting attempt causing a “Global Flash Erase”. The predefined initialized bit-values (1 or 0) must be preserved during memory writing. An undefined option bit must be keep 0 and the complement value at 1 during the memory writing sequence. STLUX Table 39. Option byte register overview - STLUX325A Option bits Address Option name 7 6 5 4 3 2 1 0 Default settings DocID027870 Rev 1 4800h ROP ROP [7:0] 00h 4801h UCB UBC [7:0] 00h 4802h nUCB nUBC [7:0] FFh 4803h GENCFG - Rst_PWM4 Rst_PWM3 Rst_PWM2 Rst_PWM1 Rst_PWM0 - EN_COLD_CFG 00h 4804h nGENCFG - nRst_PWM4 nRst_PWM3 nRst_PWM2 nRst_PWM1 nRst_PWM0 - nEN_COLD_CFG FFh 4805h MISCUOPT - - 1 - LSI_EN IWdg_hw WWdg_hw WWDG_HALT 28h 4806h nMISCUOPT - - 0 - nLSI_EN nIWdg_hw nWWdg_hw nWWDG_HALT D7h 4807h CLKCTL - - - CKAWUSEL1 EXTCLK CKAWUSE L0 PRSC [1:0] 09h 4808h nCLKCTL - - - nCKAWUSEL1 nEXTCLK nCKAWUS EL0 nPRSC [1:0] F6h 4809h HSESTAB HSECNT[7:0] 00h 480Ah nHSESTAB nHSECNT[7:0] FFh RESERVED - 480Bh 480Ch STLUX . 00h FFh WAITSTATE - - - - - - WaitStat [1:0] 00h 480Eh nWAITSTATE - - - - - - nWaitStat [1:0] FFh 480Fh AFR_IOMXP0 - - Sel_P054[1:0] Sel_P032[1:0] - - 00h 4810h nAFR_IOMXP0 - - nSel_P054[1:0] nSel_P032[1:0] - - FFh 4811h AFR_IOMXP1 AUXTMR - - Sel_P14 Sel_P13 Sel_P12 Sel_P11 Sel_P10 1Fh 4812h nAFR_IOMXP1 nAUXTMR - - nSel_P14 nSel_P13 nSel_P12 nSel_P11 nSel_P10 E0h 4813h AFR_IOMXP2 Sel_SWIM - - Sel_P254 - - - - 10h 4814h nAFR_IOMXP2 nSel_SWIM - - nSel_P254 - - - - EFh 65/126 4815h MSC_OPT0 - - UARTLine [1:0] - - BootSel [1:0] 01h 4816h nMSC_OPT0 - - nUARTLine [1:0] - - nBootSel [1:0] FEh Option bytes 480Dh Option bits Address Option name 4817h 487Dh RESERVED 7 6 5 4 3 2 1 0 - - - - - - - - Default settings 00h 487Eh OPTBL BL [7:0] 00h 487Fh nOPTBL nBL [7:0] FFh Note: Option bytes 66/126 Table 39. Option byte register overview - STLUX325A (continued) The default setting values refer to the factory configuration. The factory configuration can be overwritten by the user in accordance with the target application requirements. The factory configuration values are loosed after user programming fields or in case of the ROP unprotecting attempt causing a “Global Flash Erase”. DocID027870 Rev 1 The predefined initialized bit-values (1 or 0) must be preserved during memory writing. An undefined option bit must be keep 0 and the complement value at 1 during the memory writing sequence. STLUX Option bits Address Option name 7 6 5 4 3 2 1 0 Default settings DocID027870 Rev 1 4800h ROP ROP [7:0] 00h 4801h UCB UBC [7:0] 00h 4802h nUCB nUBC [7:0] FFh 4803h GENCFG Rst_PWM3 Rst_PWM2 Rst_PWM1 Rst_PWM0 - EN_COLD_CFG 00h 4804h nGENCFG nRst_PWM3 nRst_PWM2 nRst_PWM1 nRst_PWM0 - nEN_COLD_CFG FFh 4805h MISCUOPT - - 1 - LSI_EN IWdg_HW WWdg_HW WWDG_HALT 28h 4806h nMISCUOPT - - 0 - nLSI_EN nIWdg_HW nWWdg_HW nWWDG_HALT D7h 4807h CLKCTL - - CKAWUSEL1 EXTCLK CKAWUSE L0 PRSC [1:0] 09h 4808h nCLKCTL - - nCKAWUSEL1 nEXTCLK nCKAWUS EL0 nPRSC [1:0] F6h 4809h HSESTAB HSECNT [7:0] 00h 480Ah nHSESTAB nHSECNT [7:0] FFh RESERVED - 480Bh 480Ch STLUX Table 40. Option byte register overview - STLUX285A 00h FFh WAITSTATE - - - - - - WaitStat [1:0] 40h 480Eh nWAITSTATE - - - - - - nWaitStat [1:0] BFh 480Fh AFR_IOMXP0 - - Sel_P054 [1:0] Sel_P032 [1:0] - 00h 4810h nAFR_IOMXP0 - - nSel_P054 [1:0] nSel_P032 [1:0] - FFh 4811h AFR_IOMXP1 AUXTMR - Sel_P13 Sel_P12 Sel_P11 Sel_P10 0Fh 4812h nAFR_IOMXP1 nAUXTMR - nSel_P13 nSel_P12 nSel_P11 nSel_P10 F0h 4813h AFR_IOMXP2 1 1 - 50h 4814h nAFR_IOMXP2 0 0 - AFh 4815h MSC_OPT0 - - UARTLine [1:0] - - BootSel [1:0] 01h 4816h nMSC_OPT0 - - nUARTLine [1:0] - - nBootSel [1:0] FEh Option bytes 67/126 480Dh Option bits Address 4817h 487Dh Option name RESERVED 7 6 5 4 3 2 1 0 - - - - - - - - Default settings 00h 487Eh OPTBL BL [7:0] 00h 487Fh nOPTBL nBL [7:0] FFh Note: Option bytes 68/126 Table 40. Option byte register overview - STLUX285A (continued) The default setting values refer to the factory configuration. The factory configuration can be overwritten by the user in accordance with the target application requirements. The factory configuration values are loosed after user programming fields or in case of the ROP unprotecting attempt causing a “Global Flash Erase”. DocID027870 Rev 1 The predefined initialized bit-values (1 or 0) must be preserved during memory writing. An undefined option bit must be keep 0 and the complement value at 1 during the memory writing sequence. STLUX STLUX 10.2 Option bytes Option byte register description The option byte registers are mapped inside the E²PROM data region. ROP (memory readout protection register) Table 41. ROP (memory readout protection register) Offset: 0x004800 Default value: 0x00 7 6 5 4 3 2 1 0 ROP [7:0] r/w Bit 7 - 0: ROP [7:0] memory readout protection: 0xAA: enable readout protection. When readout protection is enabled, reading or modifying the Flash program memory and DATA area in ICP mode (using the SWIM interface) is forbidden, whatever the write protection settings are. UBC (UBC user boot code register) Table 42. UBC (UBC user boot code register) Offset: 0x004801 Default value: 0x00 7 6 5 4 3 2 1 0 UBC [7:0] r/w Bit 7 - 0: UBC [7:0] user boot code write protection memory size: 0x00: no UBC, no Flash memory write-protection 0x01: pages 0 to 1 defined as UBC; 1 Kbyte memory write-protected (0x00.80000x00.83FF) 0x02: pages 0 to 3 defined as UBC; 2 Kbyte memory write-protected (0x00.80000x00.87FF) 0x03: pages 0 to 4 defined as UBC; 2.5 Kbyte memory write-protected (0x00.80000x00.89FF) ... (512 byte every page) 0x3E: pages 0 to 63 defined as UBC; 32 Kbyte memory write-protected (0x00.80000x00.FFFF) Other values: reserved. DocID027870 Rev 1 69/126 126 Option bytes STLUX nUBC (UBC user boot code register protection) Table 43. nUBC (UBC user boot code register protection) Offset: 0x004802 Default value: 0xFF 7 6 5 4 3 2 1 0 nUBC [7:0] r/w nUBC: not (UBC) EMC byte protection. GENCFG (general configuration register) Table 44. GENCFG (general configuration register) Offset: 0x004803 Default value: 0x00 7 6 5 4 3 2 1 0 Rst_PWM [5:0] COMP1_2(1) EN_COLD_C FG r/w r/w r/w 1. Available only on the STLUX385A and STLUX383A, otherwise keep 0. Bit 0: EN_COLD_CFG enables IC cold configuration through the option byte register AFR_IOMXP0, P1 and P2: 0: default case, the IC multifunction signal configuration is performed by the miscellaneous registers MSC_IOMXP0, MSC_IOMXP1 and MSC_IOMXP2 (warm configuration). 1: enables the multifunction signal configuration through the option byte registers AFR_IOMXP0, AFR_IOMXP1 and AFR_IOMXP2 (cold configuration). Bit 1: COMP1_2 enables the complete backward compatibility with the STLUX385 IC device. Bit 7:2: Rst_PWM [5:0] configures the PWM [n] reset value after the NRST signal 0: PWM [n] output low level (native default value) 1: PWM [n] output high level. Note: The PWM signal programmed reset value is configured during the option byte loader phase, then before the NRST is released it assumes its proper initial values. The Rst_PWM5 is not available only on the STLUX325A and must be kept 0. The Rst_PWM5 and Rst_PWM4 are not available only on the STLUX325A and must be kept 0. 70/126 DocID027870 Rev 1 STLUX Option bytes nGENCFG (general configuration register protection) Table 45. nGENCFG (general configuration register protection) Offset: 0x004804 Default value: 0xFF 7 6 5 4 3 2 1 0 nRst_PWM [5:0] nCOMP1_2 nEN_COLD_CFG r/w r/w r/w nGENCFG: not (GENCFG) EMC byte protection. MISCUOPT (miscellaneous configuration register) Table 46. MISCUOPT (miscellaneous configuration register) Offset: 0x004805 Default value: 0x28 (factory configuration) 7 6 5 4 3 2 1 0 RFU RFU RFU LSI_EN lWdg_hw WWdg_hw WWDG_HALT r r r r/w r/w r/w r/w Bit 0: WWdg_HALT window watchdog reset on Halt: 0: no reset generated on Halt if WWDG is active 1: reset generated on Halt if WWDG is active. Bit 1: WWdg_hw window watchdog hardware enable: 0: window watchdog activation by SW 1: window watchdog activation by HW. Bit 2: IWdg_hw independent watchdog hardware enable: 0: independent watchdog activation by SW 1: independent watchdog activation by HW. Bit 3: LSI_EN low speed internal RCOSC clock enable: 0: LSI clock is not available to CPU 1: LSI cock is enabled for CPU. Bit 4: RFU reserved; must be kept 0 during register writing for future compatibility. Bit 5: RFU reserved; must be kept 1 during register writing for future compatibility. Bit 7 - 6: RFU reserved; must be kept 0 during register writing for future compatibility. DocID027870 Rev 1 71/126 126 Option bytes STLUX nMISCUOPT (miscellaneous configuration register protection) Table 47. nMISCUOPT (miscellaneous configuration register protection) Offset: 0x004806 Default value: 0xD7 (factory configuration) 7 6 5 4 3 2 1 0 nRFU nRFU nRFU nLSI_EN nlWdg_hw nWWdg_hw nWWdg_HALT r r r r/w r/w r/w r/w nMISCUOPT: not (MISCUOPT) EMC byte protection. CLKCTL (CKC configuration register) Table 48. CLKCTL (CKC configuration register) Offset: 0x004807 Default value: 0x09 (factory configuration) 7 6 5 4 3 2 1 0 RFU CKAWUSEL1 EXTCLK CKAWUSEL0 PRSC [1:0] r r/w r/w r/w r/w Bit 1 - 0: PRSC [1:0] prescaler value for HSE to provide the AWU unit with the low speed clock: 00: 24 MHz to 128 kHz prescaler 01: 16 MHz to 128 kHz prescaler 10: 8 MHz to 128 kHz prescaler 11: 4 MHz to 128 kHz prescaler. Bit 3: EXTCLK external clock selection: 0: external crystal oscillator clock connected to the HseOscin and HseOscout signals 1: external direct drive clock connected to the HseOscin. Bit 4, 2: CKAWUSEL[1:0] AWU clock selection: 00: low speed internal clock used for AWU module 01: HSE high speed external clock with prescaler used for AWU module 10: reserved encoding value 11: reserved encoding value. Bit 7 - 5: RFU reserved; must be kept 0 during register writing for future compatibility. 72/126 DocID027870 Rev 1 STLUX Option bytes nCLKCTL (CKC configuration register protection) Table 49. nCLKCTL (CKC configuration register protection) Offset: 0x004808 Default value: 0xF6 (factory configuration) 7 6 5 4 3 2 1 0 nRFU nCKAWUSEL1 nEXTCLK nCKAWUSEL0 nPRSC [1:0] r r/w r/w r/w r/w nCLKCTL: not (CLKCTL) EMC byte protection. HSESTAB (HSE clock stabilization register) Table 50. HSESTAB (HSE clock stabilization register) Offset: 0x004809 Default value: 0x00 7 6 5 4 3 2 1 0 HSECNT [7:0] r/w Bit 7 - 0: HSECNT [7:0] HSE crystal oscillator stabilization cycles: 0x00: 2048 clock cycles 0xB4: 128 clock cycles 0xD2: 8 clock cycles 0xE1: 0.5 clock cycles. nHSESTAB (HSE clock stabilization register protection) Table 51. nHSESTAB (HSE clock stabilization register protection) Offset: 0x00480A Default value: 0xFF 7 6 5 4 3 2 1 0 nHSECNT [7:0] r/w nHSESTAB: not (HSESTAB) EMC byte protection. DocID027870 Rev 1 73/126 126 Option bytes STLUX WAITSTATE (Flash wait state register) Table 52. WAITSTATE (Flash wait state register) Offset: 0x00480D Default value: 0x00 or 0x40 according to the device 7 6 5 4 3 2 1 0 RFU WaitStat [1:0] r r/w Bit 1 - 0: WaitStat [1:0] configures the E²PROM and Flash programmable delay read access time: 00: 0 no delay cycle (default case fMASTER at 16 MHz) 01: 1 delay cycles 10: 2 delay cycles 11: 3 delay cycles. Bit 7 - 2: RFU reserved; must be kept 0 during register writing for future compatibility. nWAITSTATE (Flash wait state register protection) Table 53. nWAITSTATE (Flash wait state register) Offset: 0x00480E Default value: 0xFF or BF according to the device 7 6 5 4 3 1 0 nRFU nWaitStat [1:0] r r/w nWAITSTATE: not (WAITSTATE) EMC byte protection. 74/126 2 DocID027870 Rev 1 STLUX Option bytes AFR_IOMXP0 (alternative Port0 configuration register) Table 54. AFR_IOMXP0 (alternative Port0 configuration register) Offset: 0x00480F Default value: 0x00 7 1. 6 5 4 3 2 1 0 RFU Sel_P054 [1:0] Sel_P032 [1:0] Sel_P010 [1:0](1) r r/w r/w r/w Available only on the STLUX385A and STLUX383A, otherwise keep 0. Bit 5 - 0: Refer to MSC_IOMXP0 miscellaneous register field description Section 8.2 on page 46. Bit 7 - 6: RFU reserved; must be kept 0 during register writing for future compatibility. nAFR_IOMXP0 (alternative Port0 configuration register protection) Table 55. nAFR_IOMXP0 (alternative Port0 configuration register protection) Offset: 0x004810 Default value: 0xFF 7 6 5 4 3 2 1 0 nRFU nSel_P054 [1:0] nSel_P032 [1:0] nSel_P010 [1:0] r r/w r/w r/w nAFR_IOMXP0: not (AFR_IOMXP0) EMC byte protection. DocID027870 Rev 1 75/126 126 Option bytes STLUX AFR_IOMXP1 (alternative Port1 configuration register) Table 56. AFR_IOMXP1 (alternative Port1 configuration register) Offset: 0x004811 Default value: 0x00 or 0x3F or 0x1F or 0x0F according to the device 7 6 5 AUXTMR RFU Sel_P15(1) 4 r/w r r/w (2) Sel_P14 3 2 1 0 Sel_P13 Sel_P12 Sel_P11 Sel_P10 r/w r/w r/w r/w r/w 1. Available only on the STLUX385A and STLUX383A, otherwise keep 0. 2. Available only on the STLUX385A, STLUX383A and STLUX325A, otherwise keep 0. Bit 5 - 0: Refer to MSC_IOMXP1 miscellaneous register field description Section 8.2.3 on page 47. Bit 6: RFU reserved; must be kept 0 during register writing for future product compatibility. Bit 7: AUXTIM CCO aux timer compatibility features 0: CCO aux timer enabled 1: CCO aux timer disabled. nAFR_IOMXP1 (alternative Port1 configuration register protection) Table 57. nAFR_IOMXP1 (alternative Port1 configuration register protection) Offset: 0x004812 Default value: 0xFF or 0xC0 or 0xE0 or 0xF0 depends on devices 7 6 5 4 3 2 1 0 nAUXTMR nRFU nSel_P15 nSel_P14 nSel_P13 nSel_P12 nSel_P11 nSel_P10 r/w r r/w r/w r/w r/w r/w r/w nAFR_IOMXP1: not (AFR_IOMXP1) EMC byte protection. 76/126 DocID027870 Rev 1 STLUX Option bytes AFR_IOMXP2 (alternative Port2 configuration register) Table 58. AFR_IOMXP2 (alternative Port2 configuration register) Offset: 0x004813 Default value: 0x10 or 0x50 according to the device 7 6 5 Sel_SWIM(1) RFU r/w r 4 (2) Sel_P254 r/w 3 2 1 0 RFU RFU RFU RFU r r r r 1. Available only on the STLUX325A, otherwise keep 0. 2. Not available on the STLUX285A, must be kept to 1. Bit 3 - 0: RFU reserved; must be kept 0 during register writing for future product compatibility Bit 4: Refer to MSC_IOMXP2 miscellaneous register field description Section 7.4 on page 39. Bit 6 - 5: RFU reserved; must be kept 0 during register writing for future product compatibility. On STLUX285A devices bit 6 must be kept to 1. Bit 7: Refer to MSC_IOMXP2 miscellaneous register field description Section 7.4 nAFR_IOMXP2 (alternative Port2 configuration register protection) Table 59. nAFR_IOMXP2 (alternative Port2 configuration register protection) Offset: 0x004814 Default value: 0xEF or 0xAF according to the device 7 6 5 4 3 2 1 0 nSel_SWIM nRFU nSel_P254 nRFU nRFU nRFU nRFU r/w r r/w r r r r nAFR_IOMXP2: not (AFR_IOMXP2) EMC byte protection. DocID027870 Rev 1 77/126 126 Option bytes STLUX MSC_OPT0 (miscellaneous configuration reg0) Table 60. MSC_OPT0 (miscellaneous configuration reg0) Offset: 0x004815 Default value: 0x01 7 6 5 4 3 2 1 0 RFU UARTline [1:0] RFU BootSel [1:0] r r/w r r/w Bit 1 - 0: BootSel [1:0] boot-ROM peripheral enables: 00: automatic scan boot sources; this selection enables the automatic scan configuration sequence of all possible initializing peripheral devices: Periph0 (UART), Periph1 (RFU). 01: enable boot source: Periph0 10: enable boot source: Periph1 11: enable boot sources: Periph1, Periph0 Bit 3 - 2: RFU reserved; must be kept 0 during register writing for future compatibility. Bit 5 - 4: UARTline [1:0] selects the UART port configuration pins involved during the bootload sequence in warm configuration mode; in case of cold configuration, this field is ignored since the UART port is selected by the register AFR_IOXP0. 00: boot sequence with the UART i/f configured in all possible UART multiplexed signal schemes. This sequence is used when UART i/f position is not specified. 01: boot sequence with UART i/f configured on P0 (1, 0) 10: boot sequence with UART i/f configured on P0 (3, 2) 11: boot sequence with UART i/f configured on P0 (5, 4). Bit 7 - 6: RFU reserved; must be kept 0 during register writing for future compatibility. nMSC_OPT0 (miscellaneous configuration reg0 protection) Table 61. nMSC_OPT0 (miscellaneous configuration reg0 protection) Offset: 0x004816 Default value: 0xFE 7 6 5 4 3 2 0 nRFU nUARTline [1:0] nRFU nBootSel [1:0] r r/w r r/w nMSC_OPT0: not (MSC_OPT0) EMC byte protection. 78/126 1 DocID027870 Rev 1 STLUX Option bytes OPTBL (option byte bootloader) Table 62. OPTBL (option byte bootloader) Offset: 0x00487E Default value: 0x00 7 6 5 4 3 2 1 0 BL [7:0] r/w Bit 7 - 0: BL [7:0] the bootloader field checked by the internal BootROM code during the STLUX initialization phase. The content of register locations 0x00487E, 0x00487F and 0x008000 determine the bootloader SW flow execution sequence. nOPTBL (option byte boot loader protection) Table 63. nOPTBL (option byte boot loader protection) Offset: 0x00487F Default value: 0xFF 7 6 5 4 3 2 1 0 nBL [7:0] r/w nOPTBL: not (OPTBL) EMC byte protection. DocID027870 Rev 1 79/126 126 Device identification STLUX 11 Device identification 11.1 Unique ID The STLUX family provides a 56-bit unique identifier code usable as a device identification number which can be used to increase the device security. The unique ID code is a frozen signature not alterable by user. The unique device identifier is ideally used by the application software and is suited for: Serial code Security keys in conjunction with cryptographic software to increase the embedded Flash code security Activating the secure boot sequence. Table 64. Unique ID register overview Unique ID bits Address Option name 7 11.2 6 5 4 3 2 1 0 48E0h UID0 LotNum [7:0] 48E1h UID1 LotNum [15:8] 48E2h UID2 LotNum [23:16] 48E3h UID3 WaferNum [4:0] Xcoord [7:5] 48E4h UID4 Xcoord [4:0] Ycoord [7:5] 48E5h UID5 Ycoord [4:0] LotNum [42:40] 48E6h UID6 LotNum [31:24] 48E7h UID7 LotNum [39:32] Device ID The STLUX family identification model is coded in the following register area and it cannot be altered by the user. Table 65. Dev ID register overview Dev ID bits Address Option name Default settings 7 6 5 3 2 1 0 4896h DVD0 DEV_ID[7:0] (1) 4897h nDVD0 nDEV_ID[7:0] (1) 4898h DVD1 RFU Rev_ID [4:0] (1) 4899h nDVD1 nRFU nRev_ID [4:0] (1) 1. See Table 66. 80/126 4 DocID027870 Rev 1 STLUX Device identification The RFU and nRFU value are reserved and the value may be changed within devices. Table 66. Device revision model overview STLUX device revision model Note: DEV_ID[7:0] Rev_ID[4:0] Device name 0x00 0b00000 STLUX385 0x00 0b00001 STLUX385A 0x10 0b00001 STLUX325A 0x02 0b00001 STLUX383A 0x20 0b00001 STLUX285A The mask DVD1 and nDVD1 register with 0x1F when read the Rev_ID [4:0] field. DocID027870 Rev 1 81/126 126 Electrical characteristics STLUX 12 Electrical characteristics 12.1 Parameter conditions Unless otherwise specified, all voltages are referred to VSS. VDDA and VDD must be connected to the same voltage value. VSS and VSSA must be connected together with the shortest wire loop. 12.1.1 Minimum and maximum values Unless otherwise specified, the minimum and maximum values are guaranteed in the worst conditions of ambient temperature, supply voltage and frequencies by tests in production on 100% of the devices with an ambient temperature at TA = 25 °C and TA = TA max. (given by the selected temperature range). Data based on characterization results, design simulation and/or technology characteristics are indicated according to each table specific notes and are not tested in production. 12.1.2 Typical values Unless otherwise specified, typical data are based on TA = 25 °C, VDD and VDDA = 3.3 V. They are given only as design guidelines and are not tested. Typical ADC accuracy values are determined by characterization of a batch of samples from a standard diffusion lot over the full temperature range. 12.1.3 Typical curves Unless otherwise specified, all typical curves are given as design guidelines only and are not tested. 12.1.4 Typical current consumption For typical current consumption measurements, VDD and VDD are connected together as shown in Figure 12. Figure 12. Supply current measurement conditions 82/126 DocID027870 Rev 1 STLUX 12.1.5 Electrical characteristics Loading capacitors The loading conditions used for pin parameter measurement are shown in Figure 13: Figure 13. Pin loading conditions 12.1.6 Pin output voltage The input voltage measurement on a pin is described in Figure 14. Figure 14. Pin input voltage DocID027870 Rev 1 83/126 126 Electrical characteristics 12.2 STLUX Absolute maximum ratings Stresses above those listed as 'absolute maximum ratings' may cause permanent damage to the device. This is a stress rating only and functional operation of the device under these conditions is not implied. Exposure to maximum rating conditions for extended periods may affect the device reliability. Table 67. Voltage characteristics Symbol Ratings Min. Max. -0.3 6.5 VSS - 0.3 VDD + 0.3 VDDX - VSSX Supply voltage(1) (2) Input voltage on any other pin VIN VDD - VDDA Variation between different power pins 50 VSS - VSSA Variation between all the different ground pins(3) 50 VESD Unit V mV Refer to absolute maximum ratings (electrical sensitivity) in Section 11.4.1 on page 93 Electrostatic discharge voltage 1. All power VDDX (VDD, VDDA) and ground VSSX (VSS, VSSA) pins must always be connected to the external power supply. 2. IINJ(PIN) must never be exceeded. This is implicitly insured if VIN maximum is respected. If VIN maximum cannot be respected, the injection current must be limited externally to the IINJ(PIN) value. A positive injection is induced by VIN > VDD while a negative injection is induced by VIN < VSS. 3. VSS and VSSA signals must be interconnected together with a short wire loop. Table 68. Current characteristics Symbol Max.(1) Ratings Total current into VDDX power lines(2) IVDDX IVSSX Total current out of VSSX power IIO lines(2) Output current sunk by any I/Os and control pin Unit 100 100 Ref. to Table 82 on page 100 mA Output current source by any I/Os and control pin (3) IINJ(PIN) , (4) IINJ(TOT)(3), (4), (5) Injected current on any pin ±4 Sum of injected currents ±20 1. Data based on characterization results, not tested in production. 2. All power VDDX (VDD, VDDA) and ground VSSX (VSS, VSSA) pins must always be connected to the external power supply. 3. IINJ(PIN) must never be exceeded. This is implicitly insured if VIN maximum is respected. If VIN maximum cannot be respected, the injection current must be limited externally to the IINJ(PIN) value. A positive injection is induced by VIN > VDD while a negative injection is induced by VIN < VSS. 4. Negative injection disturbs the analog performance of the device. 5. When several inputs are submitted to a current injection, the maximum IINJ(PIN) is the absolute sum of the positive and negative injected currents (instantaneous values). These results are based on characterization with IINJ(PIN) maximum current injection on four I/O port pins of the device. 84/126 DocID027870 Rev 1 STLUX Electrical characteristics Table 69. Thermal characteristics Symbol TSTG TJ 12.3 Ratings Max. Storage temperature range Unit -65 to 150 Maximum junction temperature ºC 150 Operating conditions The device must be used in operating conditions that respect the parameters listed in Table 70. In addition, a full account must be taken for all physical capacitor characteristics and tolerances. Table 70. General operating conditions Symbol fCPU Parameter Internal CPU clock frequency Conditions Min. -40 TA 105 °C VDD1, VDDA1 Operating voltages VDD, VDDA Nominal operating voltages Max. Unit 0 16 MHz 3(1) 5.5(1) 3.3(1) 5(1) V 470 3300 nF 0.05 0.2 15 nH 1.8(2) Core digital power supply VOUT CVOUT: capacitance of external capacitor(3) ESR of external capacitor(2) Typ. at 1 MHz (2) ESL of external capacitor JA(4) TA FR4 multilayer PCB Ambient temperature TSSOP38 TSSOP28 80 VFQFPN32 26 Pd = 100 mW -40 °C/W 105 °C 1. The external power supply can be within range from 3 V up to 5.5 V although IC performances are optimized for a power supply equal to 3.3 V. 2. Internal core power supply voltage. 3. Care should be taken when the capacitor is selected due to its tolerance, its dependency on temperature, DC bias and frequency. 4. To calculate PDmax (TA), use the formula PDmax = (TJmax - TA)/JA. DocID027870 Rev 1 85/126 126 Electrical characteristics STLUX Table 71. Operating conditions at power-up/power-down Symbol tVDD tTEMP Parameter Conditions Min.(1) Typ. Max.(1) VDD rise time rate 2 µs/V 1 sec./V(2) VDD fall time rate 2 µs/V 1 sec./V(2) Reset release delay VDD rising 3 ms VIT+ Power-on reset threshold 2.65 2.8 2.98 VIT- Brownout reset threshold 2.58 2.73 2.88 VHYS(BOR) Brownout reset hysteresis 70 Unit V mV 1. Guaranteed by design, not tested in production. 2. Power supply ramp must be monotone. 12.3.1 VOUT external capacitor The stabilization of the main regulator is achieved by connecting an external capacitor CVOUT(c) to the VOUT pin. The CVOUT is specified in Section 12.3: Operating conditions. Care should be taken to limit the series inductance to less than 15 nH. Figure 15. External capacitor CVOUT 12.3.2 Supply current characteristics The STLUX supply current is calculated by summing the supply base current in the desired operating mode as per Table 72, with the peripheral supply current value reported in Table 74 on page 90 and Table Table 75 on page 92. For example, considering an application where: fMASTER = fCPU = 16 MHz provided by HSI internal RC oscillator CPU code execution in Flash All base peripheral actives: I2C, UART, DALI, ITC, GPIO0, SysTmrWWDG and IWDG ADC conversion frequency fADC = 5.3 MHz ACU (comparator and DAC units) active 6 PWM toggling at fPWM = 0.5 MHz provided by 6 SMEDs running at fSMED = 12 MHz (NPWM = 6). c. 86/126 ESR is the equivalent series resistance and ESL is the equivalent inductance. DocID027870 Rev 1 STLUX Electrical characteristics The total current consumption is given by Equation 1: Equation 1 IDD = IDD(Run2) + IDD(ADC2) + IDD(ACU) + IDD(PLL) + IDD(PWM) where IDD(PWM) = IDD(PWM1) * NPWM More generally, the PWM current consumption has to be individually evaluated for each fSMED clock grouping, using Equation 2. Equation 2 NfSMED I DD PWM = i = 1 XXXX I DD PWM i1 N i where i = fSMED clock group index; Ni = PWM number of the i_th clock group; NfSMED = fSMED clock group number. DocID027870 Rev 1 87/126 126 Electrical characteristics STLUX IC supply base current consumption Table 72 summarizes the current consumption measured on VDD/VDDA supply pins in relevant operative conditions. Table 72. Supply base current consumption at VDD/VDDA = 3.3/5 V Symbol Code Peripheral Consumption(1) Clock fMASTER (2) (3) fCPU Periph , (4) Note (4) Typ. Max. Enb/Dis mA mA 2 All 2.3 2.77 16 16 All 9.4 11.3 HSI 16 16 All 4.2 5.1 Flash HSE(5) 16 16 All 10.0 12.1 VDD/VDDA = 3.3 V 10.6 12.74 VDD/VDDA = 5 V IDD(Run5) RAM HSE(5) 16 16 All 4.6 5.53 VDD/VDDA = 3.3 V 5.2 6.63 VDD/VDDA = 5 V IDD(SLOW1) Flash HSI 16 2 All 3.6 4.33 IDD(SLOW2) RAM HSI 16 2 All 2.9 3.5 IDD(SLOW3) Flash HSE(5) 16 2 All 3.9 4.7 VDD/VDDA = 3.3 V 4.5 5.5 VDD/VDDA = 5 V IDD(SLOW4) Flash HSI 16 0.125 All 2.7 3.3 IDD(SLOW5) Flash HSE(5) 16 0.125 All 3.0 3.7 VDD/VDDA = 3.3 V 3.6 4.4 VDD/VDDA = 5 V IDD(SLOW6) Flash LSI 0.153 0.153 All 1.5 1.9 IDD(WFI1) Flash HSI 16 16 All 2.6 3.2 IDD(WFI2) Flash HSE(5) 16 16 All 3.1 3.8 VDD/VDDA = 3.3 V 3.8 5.6 VDD/VDDA = 5 V Op. mode Code area Source MHz MHz IDD(Run1) Flash HSI 2 IDD(Run2) Flash HSI IDD(Run3) RAM IDD(Run4) Description Reset exit condition 1. Data based on characterization results not tested in production. 2. “All” means: I2C, UART, DALI, ITC, GPIO0, SysTmr, WWDG and IWDG peripherals active. 3. The peripheral current consumption is supplied by the VCORE voltage (1.8 V). 4. Temperature operating: TA = 25 °C. 5. HSE frequency provided by external quartz. 88/126 DocID027870 Rev 1 STLUX Electrical characteristics IC low power current consumption Table 73 summarizes the current consumption measured on VDD/VDDA supply pins in power saving conditions. Table 73. Supply low power consumption at VDD/VDDA = 3.3/5 V Symbol Code Clock Consumption(1) Peripheral 2 E PROM fMASTER (4) MVRreg. (5) (6) (7) Typ. , Note (8) (7) Max. , Op. mode(2),(3) Code area Source MHz Enable Enable mA mA IDD(AHLT1) Flash HSI 16 Enable Enable 0.23 0.32 AWU clocked by LSI IDD(AHLT2) Flash HSI 16 Enable Disable 0.085 0.12 AWU clocked by LSI IDD(AHLT3) Flash HSE(9), (10) 16 Enable Enable 0.73 0.90 VDD/VDDA = 3.3 V 1.4 1.7 VDD/VDDA = 5 V IDD(AHLT4) Flash HSE(9), (10) 16 Enable Disable 0.65 0.95 VDD/VDDA = 3.3 V 1.2 1.45 VDD/VDDA = 5 V IDD(HLT1) Flash 16 Enable Disable 0.087 0.13 IDD(HLT2) Flash HSE(9), (10) 16 Enable Disable 0.075 0.11 VDD/VDDA = 3.3 V 0.090 0.15 VDD/VDDA = 5 V HSI Description 1. Data based on characterization results not tested in production. 2. Active halt op. mode: all peripherals except AWU and IWDG are disabled (clock gated). 3. HALT op. mode: all peripherals are disabled (clock gated). 4. E2PROM is considered always enabled. 5. .VCORE main DC voltage regulator. 6. Temperature operating: TA= 25 °C. 7. All the analog input signals are connected to GND; the signals of the port P0, P1 and P2 are configured as input with the pull-up enabled. 8. Temperature operating: TA= 105 °C. 9. HSE frequency provided by external quartz. 10. AWU clocked by HSE source clock. DocID027870 Rev 1 89/126 126 Electrical characteristics STLUX IC peripheral current consumption (3.3 V) Table 74 summarizes the peripheral current consumption measured on VDD/VDDA supply pins. Table 74. Peripheral supply current consumption at VDD/VDDA = 3.3 V Symbol Clock Consumption(1) Peripherals PLL fSMED(2) fPWM(3) fADC(4) ADC(5) PWM (6),(7) ACU(8) Typ.(9) Max.(9) Enb/Dis MHz MHz MHz Enb/Dis Num Enb/Dis mA mA IDD(PLL) Enab 0 0 0 Disab 0 Disab 2.3 2.7 IDD(ACU) Disab 0 0 0 Disab 0 Enab 1.9 2.3 1.8 2.1 6.69 8.32 8.55 10.4 Op.mode IDD(PWM1PLL96) IDD(PWM4PLL96) IDD(PWM5PLL96) 1 Enab 96 0.5 0 Disab 4 5 Disab IDD(PWM6PLL96) 6 10.12 12.2 IDD(PWM1PLL48) 1 1.12 1.4 4.31 5.31 5.6 6.8 IDD(PWM4PLL48) IDD(PWM5PLL48) Enab 48 0.5 0 Disab 4 5 Disab IDD(PWM6PLL48) 6 6.54 7.85 IDD(PWM1PLL24) 1 0.71 0.9 2.89 3.54 3.9 4.7 IDD(PWM4PLL24) IDD(PWM5PLL24) Enab 24 0.5 0 Disab 4 5 Disab IDD(PWM6PLL24 6 4.39 5.27 IDD(PWM1PLL12) 1 0.6 0.7 2.2 2.69 2.95 3.6 IDD(PWM4PLL12) IDD(PWM5PLL12) Enab 12 0.5 0 Disab 4 5 Disab IDD(PWM6PLL12) 6 3.33 4 IDD(PWM1PLL6) 1 0.5 0.6 1.85 2.26 2.6 3.2 IDD(PWM4PLL6) IDD(PWM5PLL6) Enab 6 0.5 0 Disab 4 5 Disab IDD(PWM6PLL6) 6 2.81 3.4 IDD(PWM1HSI16) 1 0.5 0.6 1.79 2.19 2.3 3 2.63 3.3 IDD(PWM4HSI16) IDD(PWM5HSI16) Enab 16 0.5 0 Disab 5 6 IDD(PWM6HSI16) 90/126 4 DocID027870 Rev 1 Disab STLUX Electrical characteristics Table 74. Peripheral supply current consumption at VDD/VDDA = 3.3 V (continued) Symbol Clock IDD(PWM1HSI8) IDD(PWM4HSI8) IDD(PWM5HSI8) Consumption(1) Peripherals 1 Enab 8 0.5 0 Disab 4 5 Disab 0.4 0.5 1.39 1.7 1.95 2.4 IDD(PWM6HSI8) 6 2.12 2.55 IDD(PWM1HSI4) 1 0.3 0.4 1.21 1.48 1.7 2.2 IDD(PWM4HSI4) IDD(PWM5HSI4) Enab 4 0.5 0 Disab 4 5 Disab IDD(PWM6HSI4) 6 1.78 2.2 IDD(PWM1HSI2) 1 0.25 0.3 1.07 1.31 1.52 1.9 1.60 1.93 IDD(PWM4HSI2) IDD(PWM5HSI2) Enab 2 0.5 0 Disab 4 5 Disab 6 IDD(PWM6HSI2) IDD(ADC1) Disab 0 0 1 Enab 0 Disab 1.55 1.87 IDD(ADC2) Disab 0 0 5.3 Enab 0 Disab 1.6 1.95 IDD(ADC3) Enab 0 0 6 Enab 0 Disab 1.56 1.88 1. Data based on characterization results not tested in production. 2. SMED frequency: - 96 MHz and 6 MHz frequencies require the PLL enabled. - Current table shows only a subset value of possible SMED frequencies. 3. PWM frequency: - PWM toggle frequency is considered fixed to 500 kHz, close to the maximum applicative value. 4. 3.ADC frequency: - 6 MHz frequency requires the PLL enabled. - Current table shows only a subset value of possible ADC frequencies. 5. ADC configured in circular mode. 6. PWM pins are loaded with a CL (load capacitance) of 50 pF. 7. Number of active PWMs. 8. If enabled all DACs and comparator units are active. 9. Temperature operating: TA = 25 °C. DocID027870 Rev 1 91/126 126 Electrical characteristics STLUX IC peripheral current consumption (5 V) Table 75 summarizes the peripheral current consumption measured on VDD/VDDA supply pins. Table 75. Peripheral supply current consumption at VDD/VDDA = 5 V Symbol Clock Consumption(1) Peripherals PLL fSMED(2) fPWM(3) fADC(4) ADC(5) PWM(6), (7) ACU(8) Typ.(9) Max.(9) Enb/Dis MHz MHz MHz Enb/Dis Num Enb/Dis mA mA IDD(PLL) Enab 0 0 0 Disab 0 Disab 2.32 2.78 IDD(ACU) Disab 0 0 0 Disab 0 Enab 2.22 2.66 1.81 2.17 6.98 8.69 9.0 10.8 Op. mode IDD(PWM1PLL96) IDD(PWM4PLL96) IDD(PWM5PLL96) 1 Enab 96 0.5 0 Disab 4 5 Disab IDD(PWM6PLL96) 6 10.49 12.52 IDD(PWM1PLL48) 1 1.18 1.42 4.58 5.65 5.9 7.5 IDD(PWM4PLL48) IDD(PWM5PLL48) Enab 48 0.5 0 Disab 4 5 Disab IDD(PWM6PLL48) 6 6.88 8.26 IDD(PWM1PLL24) 1 0.8 0.95 3.16 3.88 4.2 5.2 IDD(PWM4PLL24) IDD(PWM5PLL24) Enab 24 0.5 0 Disab 4 5 Disab IDD(PWM6PLL24) 6 4.73 5.68 IDD(PWM1PLL12) 1 0.6 0.7 2.46 3.01 3.3 4.2 IDD(PWM4PLL12) IDD(PWM5PLL12) Enab 12 0.5 0 Disab 4 5 Disab IDD(PWM6PLL12) 6 3.66 4.4 IDD(PWM1PLL6) 1 0.5 0.6 2.11 2.58 2.9 3.6 IDD(PWM4PLL6) IDD(PWM5PLL6) Enab 6 0.5 0 Disab 4 5 Disab IDD(PWM6PLL6) 6 3.11 3.75 IDD(PWM1HSI16) 1 0.6 0.7 2.04 2.49 2.8 3.4 3.13 3.78 IDD(PWM4HSI16) IDD(PWM5HSI16) Enab 16 0.5 0 Disab 5 6 IDD(PWM6HSI16) 92/126 4 DocID027870 Rev 1 Disab STLUX Electrical characteristics Table 75. Peripheral supply current consumption at VDD/VDDA = 5 V (continued) Symbol Clock IDD(PWM1HSI8) IDD(PWM4HSI8) IDD(PWM5HSI8) Consumption(1) Peripherals 1 Enab 8 0.5 0 Disab 4 5 Disab 0.5 0.6 1.64 2.0 2.3 2.9 IDD(PWM6HSI8) 6 2.56 3.1 IDD(PWM1HSI4) 1 0.47 0.55 1.48 1.81 2.2 2.7 IDD(PWM4HSI4) IDD(PWM5HSI4) Enab 4 0.5 0 Disab 4 5 Disab IDD(PWM6HSI4) 6 2.33 2.78 IDD(PWM1HSI2) 1 0.4 0.54 1.31 1.6 1.9 2.3 2.1 2.49 IDD(PWM4HSI2) IDD(PWM5HSI2) Enab 2 0.5 0 Disab 4 5 Disab 6 IDD(PWM6HSI2) IDD(ADC1) Disab 0 0 1 Enab 0 Disab 2.11 2.54 IDD(ADC2) Disab 0 0 5.3 Enab 0 Disab 2.16 2.6 IDD(ADC3) Enab 0 0 6 Enab 0 Disab 2.17 2.61 1. Data based on characterization results not tested in production. 2. SMED frequency: - 96 MHz and 6 MHz frequencies require the PLL enabled. - Current table shows only a subset value of possible SMED frequencies. 3. PWM frequency: - PWM toggle frequency is considered fixed to 500 kHz, close to the maximum applicative value. 4. ADC frequency: - 6 MHz frequency requires the PLL enabled. - Current table shows only a subset value of possible ADC frequencies. 5. ADC configured in circular mode. 6. Number of active PWMs. 7. PWM pins are loaded with a CL (load capacitance) of 50 pF. 8. If enabled all DACs and comparator units are active. 9. Temperature operating: TA = 25 °C. DocID027870 Rev 1 93/126 126 Electrical characteristics STLUX PWM current consumption overview From Figure 16 to Figure 19 provide an outline view of PWM current consumption results.The consumptions are evaluated considering the maximum current at TA = 25 °C with different SMED operating frequencies. The charts summarize the measurements carried out fromTable 74 on page 90 and Table 75 allowing users to derive the PWM current consumption values. Figure 16. PWM current consumption with fSMED = PLL fPWM = 0.5 MHz at VDD/VDDA = 5 V Figure 17. PWM current consumption with fSMED = PLL fPWM = 0.5 MHz at VDD/VDDA = 5 V 94/126 DocID027870 Rev 1 STLUX Electrical characteristics Figure 18. PWM current consumption with fSMED = HSI fPWM = 0.5 MHz at VDD/VDDA = 3.3 V Figure 19. PWM current consumption with fSMED = HSI fPWM = 0.5 MHz at VDD/VDDA = 5 V DocID027870 Rev 1 95/126 126 Electrical characteristics STLUX Low power mode wake-up time Table 76 shows the wake-up time to resume the normal operating mode from the different low power state. Table 76. Wake-up times Symbol Parameter Wake-up time from tWU(WFI) wait mode to run mode(2) Wake-up time active tWU(AH) halt mode to run mode(2) Typ.(1) Max.(1) Unit Conditions Ref.(3) fCPU fMASTER = 0 to 16 MHz fCPU = fMASTER = 16 MHz 0.56 (5) MVR voltage regulator Flash in operating mode (4) on Flash in power- down mode(5) 4(6) (5) MVR voltage regulator Flash in operating mode off(4) Flash in power- down mode(5) HSI (after wake-up) s 47(6) 49(6) Wake-up Flash in operating mode(5) time from halt mode to run Flash in power-down mode(5) mode(2) tWU(H) 6(6) 51 53 1. Data based on characterization results, not tested in production. 2. Measured from the interrupt event to interrupt vector fetch. 3. tWU(WFI) = 2 x 1/fMASTER + 7 x 1/fCPU. 4. Configured by the REGAH bit in the CLK_ICKR register. 5. Configured by the AHALT bit in the FLASH_CR1 register. 6. Plus 1 LSI clock depending on synchronization (fLSI = 153.6 kHz). 12.3.3 External clock sources and timing characteristics HSE user external clock Subject to general operating conditions for VDD and TA. Table 77. HSE user external clock characteristics Symbol fHSE_ext User external clock source frequency Conditions Min. Max. Unit -40 °C TA 105 °C 0 16(1) MHz V (2) HSEOSCIN input pin high level voltage 0.7 x VDD VDD (2) HSEOSCIN input pin low level voltage VSS 0.3 x VDD -1 +1 VHSEH VHSEL Parameter ILEAKHSE(2) VSS VIN VDD HSEOSCIN input pin leakage 1. In case fHSE is configured as a direct clock for the SMED logics the maximum frequency can be 24 MHz. 2. Data based on characterization results, not tested in production. 96/126 DocID027870 Rev 1 µA STLUX Electrical characteristics Figure 20. HSE external clock source HSE crystal/ceramic resonator oscillator The HSE clock can be supplied with a 1 to 24 MHz crystal/ceramic resonator oscillator. All the information given in this paragraph is based on characterization results with specified typical external components. In the application, the resonator and the load capacitors have to be placed as close as possible to the oscillator pins in order to minimize output distortion and start-up stabilization time. Refer to the crystal resonator manufacturer for more details (frequency, package, accuracy, etc.). . Table 78. HSE crystal/ceramic resonator oscillator Symbol Parameter Conditions External high speed oscillator frequency fHSE RF Min. Typ. 1 Feedback resistor gm tSU(HSE) HSE oscillator power consumption Oscillator transconductance (4) Startup time Unit 16(1) MHz 220 CL1, CL2(2) Recommended load capacitance(3) IDD(HSE) Max. k 20 pF 6 (startup) 2 (stabilized) mA 5 VDD is stabilized mA/V 2.8 ms 1. In case fHSE is configured as a direct clock for the SMED logic the maximum frequency can be 24 MHz. 2. The oscillator needs two load capacitors, CL1 and CL2, to act as load for the crystal. The total load capacitance (Cload) is (CL1 * CL2)/ (CL1 + CL2). If CL1 = CL2, Cload = CL1 / 2. Some oscillators have built-in load capacitors, CL1 and CL2. 3. The oscillator selection can be optimized in terms of supply current using a high quality resonator with small Rm value. 4. tSU(HSE) is the start-up time measured from the moment it is enabled (by software) to a stabilized 16 MHz oscillation is reached. This value is measured for a standard crystal resonator and it can vary significantly with the crystal manufacturer. DocID027870 Rev 1 97/126 126 Electrical characteristics STLUX Figure 21. HSE oscillator circuit diagram The crystal characteristics have to be checked with Equation 3: Equation 3 gm» gmCritic where gmCritic is calculated with the crystal parameters as follows: Equation 4 gmCritic = (2 * * fHSE)2 * Rm (2CO + C)2 and where: Rm: motional resistance(d) Lm: motional inductance(d) Cm: motional capacitance(d) CO: shunt capacitance(d) CL1 = CL2 = C: grounded external capacitance d. Refer to the application crystal specification. 98/126 DocID027870 Rev 1 STLUX 12.3.4 Electrical characteristics Internal clock sources and timing characteristics HSI RC oscillator Subject to general operating conditions for VDD and TA. Table 79. HSI RC oscillator Symbol fHSI ACCHSI tSU(HSI) Parameter Min.(1) Typ. Max.(1) Unit Conditions Frequency 16 Accuracy of HSI oscillator (factory calibrated)(1), (2) MHz VDD = 3.3 V TA= 25 ºC -1% +1% VDD = 3.3 V -40 ºC TA 105 ºC -4% +4% VDD = 5 V -40 ºC TA 105 ºC -4% +4% HSI oscillator wake-up time including calibration 1 % µs 1. Data based on characterization results, not tested in production. 2. Variation referred to fHSI nominal value. LSI RC oscillator Subject to general operating conditions for VDD and TA. Table 80. LSI RC oscillator Symbol fLSI Parameter Conditions Min.(1) Frequency Typ. Max.(1) 153.6 ACCLSI Accuracy of LSI oscillator 3.3 V VDD 5 V -40 ºC TA 105 ºC -10% tSU(LSI) LSI oscillator wake-up time Unit kHz 10% 7 % µs 1. Guaranteed by design, not tested in production. PLL internal source clock Table 81. PLL internal source clock Symbol Parameter fIN Input frequency(2) fOUT Output frequency tlock PLL lock time Conditions 3.3 V VDD 5 V -40 ºC TA 105 ºC Min.(1) Typ. Max.(1) 16 Unit MHz 96 200 µs 1. Data based on characterization results, not tested in production. 2. PLL maximum input frequency 16 MHz. DocID027870 Rev 1 99/126 126 Electrical characteristics 12.3.5 STLUX Memory characteristics Flash program and memory/data E2PROM memory General conditions: TA = -40 °C to 105 °C. Table 82. Flash program memory/data E2PROM memory Typ.(1) Max.(1) Standard programming time (including erase) for byte/word/block (1 byte/4 bytes/128 bytes) 6 6.6 Fast programming time for 1 block (128 bytes) 3 3.3 Erase time for 1 block (128 bytes) 3 3.3 Symbol tPROG tERASE Parameter Erase/write NWE tRET IDDPRG cycles(2) Conditions Min.(1) ms (program memory) TA = 25 °C 10 K TA = 85 °C 100 K TA = 105 °C 35 K Data retention (program memory) after 10 K erase/write cycles at TA= 25 °C TRET = 85 °C 15 Data retention (program memory) after 10 K erase/write cycles at TA= 25 °C TRET = 105 °C 11 Data retention (data memory) after 100 K erase/write cycles at TA = 85 °C TRET = 85 °C 15 Data retention (data memory) after 35 K erase/write cycles at TA= 105 °C TRET = 105 °C 6 Erase/write cycles(2)(data memory) Supply current during program and erase cycles Unit ms Cycles Years -40 ºC TA 105 ºC 2 mA 1. Data based on characterization results, not tested in production. 2. The physical granularity of the memory is 4 bytes, so cycling is performed on 4 bytes even when a write/erase operation addresses a single byte. 100/126 DocID027870 Rev 1 STLUX 12.3.6 Electrical characteristics I/O port pin characteristics Subject to general operating conditions for VDD and TA unless otherwise specified. Unused input pins should not be left floating. Table 83. Voltage DC characteristics Symbol VIL VIH Min.(1) Description Input low voltage (2) Input high voltage Typ. Max.(1) -0.3 0.3 * VDD 0.7 * VDD VDD VOL1 Output low voltage at 3.3 V , 0.4(5) VOL2 Output low voltage at 5 V(3), (4) 0.5 VOL3 Output low voltage high sink at 3.3 V / 5 V(2),(6), (7) VOH1 VOH2 (3) (4) Output high voltage at 3.3 Output high voltage at 5 V(3), (4) VDD - V(3), (4) VOH3 Output high voltage high sink at 3.3 V / 5 HVS Hysteresis input voltage(8) RPU Pull-up resistor Unit 0.6(5) V 60 k 0.4(5) VDD - 0.5 V(2), (6), (7) VDD - 0.6(5) 0.1 * VDD 30 45 1. Data based on characterization result, not tested in production. 2. All signals are not 5 V tolerant (input signals can't be exceeded VDDX (VDDX = VDD, VDDA). 3. A high sink selectable by high speed configuration; the parameter applicable to signals: GPIO0 [5:0] (product depending). 4. The parameter applicable to signals: GPIO1 [5:0]/PWM [5:0] (product depending). 5. Electrical threshold voltage not yet characterized at -40 ºC. 6. The parameter applicable to the signal: SWIM. 7. The parameter applicable to the signal: DIGIN [0]/CCO_clk. 8. Applicable to any digital inputs. DocID027870 Rev 1 101/126 126 Electrical characteristics STLUX Table 84. Current DC characteristics Symbol IOL1 IOL2 Min. Typ. Max.(1) Unit Description Standard output low level current at 3.3 V and VOL1(2), (3) Standard output low level current at 5 V and 1.5 VOL2(2), (3) 3 (2) (4) (5) IOLhs1 High sink output low level current at 3.3 V and VOL3 , , IOLhs2 High sink output low level current at 5 V and VOL3(2), (4), (5) Standard output high level current at 3.3 V and VOH1 , IOH2 Standard output high level current at 5 V and VOLH2(2), (3) High sink output high level current at 3.3 V and IOHhs2 High sink output high level current at 5 V and VOH3(2), (4), (5) I_Inj Input leakage current digital - analog VSS Injection mA 1.5 3 VOH3(2), (4), (5) IOHhs1 I_Inj 7.75 (2) (3) IOH1 ILKg 5 5 7.75 VIN VDD(6) ±1 current(7), (8) µA ±4 Total injection current (sum of all I/O and control pins)(7) mA ± 20 1. Data based on characterization result, not tested in production. 2. A high sink selectable by high speed configuration; the parameter applicable to signals: GPIO0 [5:0] (product depending). 3. The parameter applicable to signals: GPIO1 [5:0]/PWM [5:0] (product depending). 4. The parameter applicable to the signal: SWIM. 5. The parameter applicable to the signal: DIGIN [0]/CCO_clk. 6. Applicable to any digital inputs. 7. Maximum value must never be exceeded. 8. Negative injection current on the ADCIN [7:0] signals (product depending) have to avoid since impact the ADC conversion accuracy. Table 85. Operating frequency characteristics Symbol Description Min. Typ. Max.(1) fIL1 Digital input signal operating frequency(2), (3), (4) 12 fIH1 Analog input signal operating frequency(5), (6) 24 fIH2 (7) (8) High speed input signal operating frequency , 128 load(2) fOL1 Standard output signal operating frequency with 50 pF max. fOL2 High sink output signal operating frequency with 50 pF max. load(2), (3) 10 fOH1 High speed output signal operating frequency with 50 pF max. load(7) 12 fOH2 load(8) 32 High speed output signal operating frequency with 50 pF max. 2 1. Data based on characterization result, not tested in production. 2. A high sink selectable by high speed configuration; parameter applicable to signals: GPIO0 [5:0] (product depending). 3. The parameter applicable to the signal: SWIM. 4. The parameter applicable to signals: DIGIN [5:1] (product depending). 5. The parameter applicable to signals: GPIO0 [3:2] when configured as HSE_Oscin/Oscout. 6. The parameter applicable to any analog signals: ADCIN [7:0], CPP [3:0] and CPM3 (product depending). 7. The parameter applicable to signals: GPIO1 [5:0]/PWM [5:0] (product depending). 8. The parameter applicable to the signal: DIGIN [0]/CCO_clk. 102/126 DocID027870 Rev 1 Unit MHz STLUX 12.3.7 Electrical characteristics Typical output level curves This section shows the typical output voltage level curves measured on a single output pin for the three pad family present in the STLUX family. Standard pad This pad is associated to the following signals: DIGIN [5:1], SWIM, GPIO0 [3:0], CPP [3:0], CPM3 and ADCIN [7:0] when available. Figure 22. VOH standard pad at 3.3 V Figure 23. VOL standard pad at 3.3 V DocID027870 Rev 1 103/126 126 Electrical characteristics STLUX Figure 24. VOH standard pad at 5 V Figure 25. VOL standard pad at 5 V 104/126 DocID027870 Rev 1 STLUX Electrical characteristics Fast pad This pad is associated to the PWM [5:0] signals if the external pin is available. Figure 26. VOH fast pad at 3.3 V Figure 27. VOL fast pad at 3.3 V DocID027870 Rev 1 105/126 126 Electrical characteristics STLUX Figure 28. VOH fast pad at 5 V Figure 29. VOL fast pad at 5 V 106/126 DocID027870 Rev 1 STLUX Electrical characteristics High speed pad This pad is associated to the DIGIN [0] signals. Figure 30. VOH high speed pad at 3.3 V Figure 31. VOL high speed pad at 3.3 V DocID027870 Rev 1 107/126 126 Electrical characteristics STLUX Figure 32. VOH high speed pad at 5 V Figure 33. VOL high speed pad at 5 V 108/126 DocID027870 Rev 1 STLUX 12.3.8 Electrical characteristics Reset pin characteristics Subject to general operating conditions for VDD and TA unless otherwise specified. Table 86. NRST pin characteristics Symbol VIL(NRST) VIH(NRST) Parameter NRST input low level voltage(1) NRST input high level voltage (1) VOL(NRST) NRST output low level voltage RPU(NRST) NRST pull-up resistor tIFP(NRST) (1) Max.(1) Typ. Unit -0.3 0.3 x VDD 0.7 x VDD VDD + 0.3 IOL = 2 mA (2) 30 40 60 k 75 pulse(3) ns 500 NRST output filtered pulse(3) V 0.5 NRST input filtered pulse(3) tINFP(NRST) NRST not input filtered tOP(NRST) Min.(1) Conditions 15 µs 1. Data based on characterization results, not tested in production. 2. The RPU pull-up equivalent resistor is based on a resistive transistor. 3. Data guaranteed by design, not tested in production. 12.3.9 I2C interface characteristics Table 87. I2C interface characteristics Standard mode Symbol Parameter Fast mode(1) Min.(2) Max.(2) Min.(2) Max.(2) tw(SCLL) SCL clock low time 4.7 1.3 tw(SCLH) SCL clock high time 4.0 0.6 tsu(SDA) SDA setup time 250 100 SDA data hold time 0(3) 0(3) th(SDA) µs 900(3) V)(4) 1000 300 tf(SDA) tf(SCL) SDA and SCL fall time (VDD = 3.3 to 5 V)(4) 300 300 tr(SDA) tr(SCL) SDA and SCL rise time (VDD = 3.3 to 5 Unit ns th(STA) START condition hold time 4.0 0.6 tsu(STA) Repeated START condition setup time 4.7 0.6 tsu(STO) STOP condition setup time 4.0 0.6 µs STOP to START condition time (bus free) 4.7 1.3 µs tw(STO:STA) Cb Capacitive load for each bus line(5) 50 µs 50 pF 2 1. fMASTER, must be at least 8 MHz to achieve maximum fast I C speed (400 kHz). 2. Data based on standard I2C protocol requirement, not tested in production. 3. The maximum hold time of the start condition has only to be met if the interface does not stretch the low time. 4. I2C multifunction signals require the high sink pad configuration and the interconnection of 1 K pull-up resistances. 5. 50 pF is the maximum load capacitance value to meet the I2C std timing specifications. DocID027870 Rev 1 109/126 126 Electrical characteristics 12.3.10 STLUX 10-bit SAR ADC characteristics Subject to general operating conditions for VDDA, fMASTER, and TA unless otherwise specified. Table 88. ADC characteristics Symbol N Parameter Conditions Resolution Max. bit ADC Clock frequency M 1 Conversion voltage range for gain x1 0 VIN2 Conversion voltage range for gain x4(4) 0 Vref ADC main reference voltage(5) Sampling time 6 (1) (2) 1.25 , 1.250 fADC = 6 MHz MHz (3) 0.3125(2), (3) V 0.50 tSTAB Wakeup time from ADC standby tCONV1 Single conversion time including sampling time fADC = 6 MHz 2.42 tCONV2 Continuous conversion time including sampling time fADC = 6 MHz 3 30 1. Frequency generated selecting the PLL source clock. 2. Maximum input analog voltage cannot exceed VDDA. 3. Exceeding the maximum voltage on the ADCIN [7:0] signals (product depending) for the related conversion scale must be avoided since the ADC conversion accuracy can be impacted. 4. Product depending. 5. ADC reference voltage at TA = 25 °C. 110/126 Unit 1 VIN1 tS Typ. 10 RADCIN ADC input impedance fADC Min. DocID027870 Rev 1 µs STLUX Electrical characteristics ADC accuracy characteristics at VDD/VDDA 3.3 V Table 89. ADC accuracy characteristics at VDD/VDDA 3.3 V Symbol Conditions(1) Parameter Typ.(2) |ET| Total unadjusted error(4), (5), (6) 2.8 |EO| (4) (5) (6) 0.3 (4) (5) (6) (7) 0.4 |EG| Offset error , , Gain error( , , (7) (8) EO+G Offset + gain error , EO+G Offset + gain error(7), (9) EO+G |ED| fADC = 6 MHz gain 1 (7) (10) Offset + gain error , Differential linearity error(2), (3), (4) |EL| Integral linearity 1.4 |ET| Total unadjusted error(4), (5), (6) 2.8 |EO| Offset error(4), (5), (6) 0.3 (4) (5) (6) (7) Gain error , , , Offset + gain EO+G Offset + gain error(5), (9) EO+G |ED| |EL| Offset + gain fADC = 6 MHz gain 4 (11) error(7), (10) Differential linearity Integral linearity -8.5 9.3 -11 11 -14.3 11.3 Unit LSB 0.4 error(7) (8) EO+G Max.(3) 0.5 error(4), (5), (6) |EG| Min.(3) error(4), (5), (6) -12.7 15.5 -16.7 18.8 -19.2 18.8 0.5 error((4), (5), (6) 1.4 1. Measured with RAIN < 10 k (RAIN external series resistance interconnected between the AC signal generator and the ADC input pin). 2. Temperature operating: TA = 25 °C. 3. Data based on characterization results, not tested in production. 4. ADC accuracy vs. negative injection current. Injecting negative current on any of the analog input pins should be avoided as this reduces the accuracy of the conversion being performed on another analog input. It is recommended a Schottky diode (pin to ground) to be added to standard analog pins which may potentially inject the negative current. Any positive injection current within the limits specified for IINJ(PIN) and IINJ(PIN) in the I/O port pin characteristic section does not affect the ADC accuracy. The ADC accuracy parameters may be also impacted exceeding the ADC maximum input voltage VIN1 or VIN2. 5. Results in manufacturing test mode. 6. Data aligned with trimming voltage parameters. 7. Gain error evaluation with the two point method. 8. Temperature operating range: 0 ºC TA 85 ºC. 9. Temperature operating range: -25 ºC TA 105 ºC. 10. Temperature operating range: -40 ºC TA 105 ºC. 11. Product depending. DocID027870 Rev 1 111/126 126 Electrical characteristics STLUX ADC accuracy characteristics at VDD/VDDA 5 V Table 90. ADC accuracy characteristics at VDD/VDDA 5 V Symbol Conditions(1) Parameter Typ.(2) |ET| Total unadjusted error(4), (5), (6) TBD |EO| (4) (5) (6) 0.5 (4) (5) (6) (7) 0.4 |EG| Offset error , Gain error , , , , (7) (8) EO+G Offset + gain error , EO+G Offset + gain error(7), (9) EO+G (7) (10) |ED| fADC = 6 MHz gain 1 Offset + gain error , Differential linearity error(2), (3), (4) |EL| Integral linearity 2.0 |ET| Total unadjusted error(4), (5), (6) TBD |EO| Offset error(4), (5), (6) , , Offset + gain EO+G Offset + gain error(5), (9) EO+G |ED| |EL| Offset + gain fADC = 6 MHz gain 4(11) error(7), (10) Differential linearity Integral linearity 8.9 -10.9 10.9 -13.8 10.9 LSB 0.2 error(7), (8) EO+G -8.3 Unit 1.2 (4) (5) (6) (7) Gain error , Max.(3) 0.8 error(4), (5), (6) |EG| Min.(3) error(4), (5), (6) -12.2 15.3 -16.4 18.5 -18.8 18.5 0.8 error(4), (5), (6) 2.0 1. Measured with RAIN < 10 k (RAIN external series resistance interconnected between the AC signal generator and the ADC input pin). 2. Temperature operating: TA = 25 °C. 3. Data based on characterization results, not tested in production. 4. ADC accuracy vs. negative injection current. Injecting negative current on any of the analog input pins should be avoided as this reduces the accuracy of the conversion being performed on another analog input. It is recommended a Schottky diode (pin to ground) to be added to standard analog pins which may potentially inject negative current. Any positive injection current within the limits specified for IINJ(PIN) and IINJ(PIN) in the I/O port pin characteristic section does not affect the ADC accuracy. The ADC accuracy parameters may be also impacted exceeding the ADC maximum input voltage VIN1 or VIN2. 5. Results in manufacturing test mode. 6. Data aligned with trimming voltage parameters. 7. Gain error evaluation with the two point method. 8. Temperature operating range: 0 ºC TA 85 ºC. 9. Temperature operating range: -25 ºC TA 105 ºC. 10. Temperature operating range: -40 ºC TA 105 ºC. 11. Product depending. 112/126 DocID027870 Rev 1 STLUX Electrical characteristics ADC equivalent input circuit Figure 34 shows the ADC equivalent input circuit. Figure 34. ADC equivalent input circuit Note: Gain x1 ADC input analog voltage range is from 0 up to 1.25 V. Gain x4 ADC input analog voltage range is from 0 up to 312.5 mV (product depending). Maximum input analog voltage cannot exceed VDDA. ADC input impedance > 1 M. The ADCIN [7:0] input pins (if available) are provided by the ESD protection diodes. DocID027870 Rev 1 113/126 126 Electrical characteristics STLUX ADC conversion accuracy Figure 35. ADC conversion accuracy ADC accuracy parameter definitions: 114/126 ET = total unadjusted error: maximum deviation between the actual and the ideal transfer curves. EO = offset error: deviation between the first actual transition and the first ideal one. EOG = offset + gain error (1-point gain): deviation between the last ideal transition and the last actual one. EG = gain error (2-point gain): defined so that EOG = EO + EG (parameter correlated to the deviation of the characteristic slope). ED = differential linearity error: maximum deviation between actual steps and the ideal one. EL = integral linearity error: maximum deviation between any actual transition and the end-point correlation line. DocID027870 Rev 1 STLUX 12.3.11 Electrical characteristics Analog comparator characteristics Table 91. Analog comparator characteristics(1) Symbol Parameter Conditions VCPP Comparator input voltage range VCPM3 Comparator 3 external input voltage range CIN Voffset tCOMP Min.(2) Typ. -40 ºC TA 105 ºC Max.(2) Unit 0 1.23(3) V 0 1.23(3), (4) V Input capacitance 3 Comparator offset error pF 15 (5) Comparison delay time 50 , mV (6) ns 1. The comparator logic accuracy parameters may be also impacted exceeding the VCPP and VCPM3 maximum input voltage. 2. Data based on characterization results, not tested in production. 3. Maximum analog input voltage cannot exceed VDDA. 4. The comparator 3 can be configured with the external reference voltage signal CPM3. 5. The overdrive voltage is ± 50 mV. 6. This parameter doesn't consider the delay time of comparator signal synchronization stages and SMED logic. 12.3.12 DAC characteristics Table 92. DAC characteristics Symbol N Vfull scale Voffset Vdac Parameter Conditions Resolution Typ. Max.(1) 4 DAC full scale 1.2 DAC offset -40 ºC TA 105 ºC DAC out voltage LSB INL Min.(1) Voffset bit 1.26 V 4 mV Vfull scale mV 82 Integral non linearity Unit mV 0.12 LSB 1. Data based on characterization results, not tested in production. Equation 5 DocID027870 Rev 1 115/126 126 Electrical characteristics STLUX Equation 6 where: Vfullscale = Vfullscale (sample, T) Voffset = Voffset (sample, T) INL = INL (sample, n) 12.4 EMC characteristics 12.4.1 Electrostatic discharge (ESD) Electrostatic discharges (3 positive then 3 negative pulses separated by 1 second) are applied to the pins of each sample according to each pin combination. The sample size depends on the number of supply pins in the device (3 parts * (n + 1) supply pin). Table 93. ESD absolute maximum ratings Symbol Ratings Conditions Maximum value Unit V VESD(HBM) Electrostatic discharge voltage (human body model) TA = 25 °C, conforming to JEDEC/JESD22-A114E 2000 VESD(CDM) Electrostatic discharge voltage (charge device model) TA = 25 °C, conforming to ANSI/ESD STM 5.3.1 ESDA 500 VESD(MM) Electrostatic discharge voltage (machine model) TA = 25 °C, conforming to JEDEC/JESD-A115-A 200 Data based on characterization results, not tested in production. 12.4.2 Static latch-up Two complementary static tests are required on 10 parts to assess the latch-up performance. A supply overvoltage (applied to each power supply pin) and a current injection (applied to each input, output and configurable I/O pin) are performed on each sample. This test conforms to the EIA/JESD 78 IC latch-up standard. Table 94. Electrical sensitivity Symbol LU 116/126 Parameter Conditions Level Static latch-up class TA = 105 °C A DocID027870 Rev 1 STLUX 13 Thermal characteristics Thermal characteristics STLUX functionality cannot be guaranteed when the device operating exceeds the maximum chip junction temperature (TJmax). TJmax, in degrees Celsius, may be calculated using Equation 7: Equation 7 TJmax = TAmax + PDmax x JA) where: TAmax is the maximum ambient temperature in °C JA is the package junction to ambient thermal resistance in °C/W PDmax is the sum of PINTmax and PI/Omax (PDmax = PINTmax + PI/Omax) PINTmax is the product of IDD and VDD, expressed in watts. This is the maximum chip internal power. PI/Omax represents the maximum power dissipation on output pins where: PI/Omax = (VOL * IOL) + [(VDD - VOH) * IOH], taking into account the actual VOL/IOL and VOH/IOH of the I/Os at low and high level. Table 95. Package thermal characteristics Symbol Parameter ambient(1) JA TSSOP38 - Thermal resistance junction to JA VFQFPN32 - Thermal resistance junction to ambient(1) JA TSSOP28 - Thermal resistance junction to ambient(1) Value Unit 80 °C/W 26 °C/W 80 °C/W 1. Thermal resistance is based on the JEDEC JESD51-2 with the 4-layer PCB in a natural convection environment. DocID027870 Rev 1 117/126 126 Package information 14 STLUX Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. 14.1 TSSOP38 package information Figure 36. TSSOP38 package outline 0117861_C 118/126 DocID027870 Rev 1 STLUX Package information Table 96. TSSOP38 package mechanical data(1) Dimensions (mm) Symbol Min. Typ. A Max. 1.20 A1 0.05 A2 0.80 b 0.17 0.27 c 0.09 0.20 (2) 9.60 9.70 9.80 E 6.20 6.40 6.60 E1(2) 4.30 4.40 4.50 D e L 1.00 1.05 0.50 0.45 L1 k 0.15 0.60 0.75 1.00 0 aaa 8 0.10 1. TSSOP stands for “Thin Shrink Small Outline Package”. 2. Dimensions “D” and “E1”do not include the mold flash or protrusions. The mold flash or protrusions shall not exceed 0.15 mm per side. DocID027870 Rev 1 119/126 126 Package information 14.2 STLUX VFQFPN32 package information Figure 37. VFQFPN32 package outline 120/126 DocID027870 Rev 1 STLUX Package information Table 97. VFQFPN32 package mechanical data(1) Dimensions (mm) Symbol Min. Typ. Max. A 0.80 0.90 1.00 A1 0 0.02 0.05 A3 0.20 b 0.18 0.25 0.30 D 4.85 5.00 5.15 D2 3.40 3.45 3.50 E 4.85 5.00 5.15 E2 3.40 3.45 3.50 0.50 0.55 0.40 0.50 e L 0.30 ddd 0.08 1. VFQFPN stands for “Thermally Enhanced Very thin Fine pitch Quad Flat Package No lead”. Very thin profile: 0.80 A 1.00 mm. Details of the terminal 1 are optional but must be located on the top surface of the package by using either a mold or marked features. Package outline exclusive of any mold flash dimensions and metal burrs. DocID027870 Rev 1 121/126 126 Package information 14.3 STLUX TSSOP28 package information Figure 38. TSSOP28 package outline 122/126 DocID027870 Rev 1 STLUX Package information Table 98. TSSOP28 package mechanical data(1) Dimensions (mm) Symbol Min. Typ. A Max. 1.20 A1 0.05 A2 0.80 b 0.19 0.30 c 0.09 0.20 (2) 9.60 9.70 9.80 E 6.20 6.40 6.60 E1(3) 4.30 4.40 4.50 D e L 1.00 1.05 0.65 0.45 L1 k 0.15 0.60 0.75 1.00 0 aaa 8 0.10 1. TSSOP stands for “Thin Shrink Small Outline Package”. 2. Dimension “D” does not include mold flash, protrusions or gate burrs. Mold flash, protrusions or gate burrs shall not exceed 0.15 mm per side. 3. Dimension “E1” does not include interlead flash or protrusions. Interlead flash or protrusions shall not exceed 0.25 mm per side. DocID027870 Rev 1 123/126 126 STLUX development environment 15 STLUX STLUX development environment The STLUX385A development environment is a suite of tools that helps developing applications guiding the user through the whole prototyping process, from the initial idea to the on-board proof of concept. It also helps beginners facing to the STLUX385A technology to get familiar with it and start developing applications as soon as possible. Analogue and system engineers can easily model the application and state machines (SMED) behavior bypassing the need to generate software code. The development environment is composed of the following tools: Peripheral libraries: open source drivers necessary to drive each hardware block. Examples software: set of software and hardware examples showing how to exploit the SMEDs functionality. Development board: board featuring STLUX and exposing all pins for external easy access. Order code: STEVAL-ILL068V1. SMED configurator: powerful graphical tool which enables the user to interact directly with the SMED without any software. Compiler: STLUX supports 2 compilers: IAR Embedded Workbench® and Raisonance Ride7. – IAR Embedded Workbench. The IAR Embedded Workbench IAR-EWSTM8 is a software development tool with highly optimizing the C and C++ compiler for the STM8 CPU device. The workbench supports the ST-LINK and STice debug probes using the SWIM interface (USB/SWIM). – Raisonance with the C compiler and the integrated development environment (Ride7), which provides start-to-finish control of application development including the code editing, compilation, optimization and debugging. – The Ride7 supports the RLink in-circuit debugger/programmer using the SWIM interface (USB/SWIM). Figure 39. STLUX development tools workflow 124/126 DocID027870 Rev 1 STLUX 16 Order codes Order codes Table 99. Ordering information Order code Package STLUX385A Tube TSSOP38 STLUX385ATR STLUX383A Tape and reel Tube TSSOP38 STLUX383ATR STLUX325A Tape and reel Tube VFQFPN32 STLUX325ATR STLUX285A Tape and reel Tube TSSOP28 STLUX285ATR 17 Packaging Tape and reel Revision history Table 100. Document revision history Date Revision 13-May-2015 1 Changes Initial release. DocID027870 Rev 1 125/126 126 STLUX IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2015 STMicroelectronics – All rights reserved 126/126 DocID027870 Rev 1