CP15TD1-24A Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 DIP-CIB 3Ø Converter + 3Ø Inverter + Brake 15 Amperes/1200 Volts � � � � � � � � � � �� �� �� � � �� ���������� ������������ � � � �� �� �� �� � �� �� �� �� �� �� �� �� �� � � � � � ������������� ���������� � ����� ������� � � � �������� ���� ��� ��� ���������� ��� ��� ��� �� ��� � ��� ��� � ��� ��� ��� ��� ��� ��� ��� ��� � � ������� ������ � �������� ����� ����� ����� ����� � ������ � ������� ���������� ������ ������������� ������� ������ ������� ������ ����� � ����� ���������� ����� � � � � � ������������ � � ���������� ��������� ���������� � � � ��������� ��������� ��������� ���������� ��������������� �� ��������� ������������ ��������� � ��� ��� ��� � ��� ��� ��� �� ��� ��� ��� �� ���� �� � �� � �� � ��� ��� Outline Drawing and Circuit Diagram Dimensions A B C D E F G H J K L M 01/06 Inches 2.68±0.01 1.73±0.02 0.58±0.004 3.1±0.02 2.83 0.16±0.01 2.83±0.01 0.07 0.2±0.008 0.87 1.91±0.023 0.94±0.02 Millimeters 68.0±0.3 44.0±0.5 14.7±0.1 79.0±0.5 72.0 4.0±0.3 72.0±0.3 2.0 5.0±0.2 22.0 48.6±0.6 23.9±0.5 Dimensions Inches Millimeters N 1.14 29.0 P 0.098 2.5 Q 0.22±0.02 5.7±0.5 R 0.18±0.008Dia. 4.5±0.2 Dia. S 0.04±0.008 1.0±0.2 T 0 Min. 0 Min. U 0.04 1.1 V 0-5° 0-5° W 0.02 Max. 0.5 Max. X 0.06±0.02 1.6±0.5 Y 0.023±0.008 0.6±0.2 Description: DIP-CIBs are low profile, thermally efficient, transfer mold modules. Each module consists of a threephase diode converter section, a three-phase inverter section and a brake circuit. Open emitters allow the designer to sense the current in each phase leg for accurate and low cost current sensing. A thermistor is included in the package for sensing the baseplate temperature. 5th Generation CSTBT chips yield low loss. The module is completely Pb-Free and hence RoHS compliant. Features: £ Compact Package £ Only 5.7mm Thick £ One Package for Entire Family £ Thermistor £ Open Emitters Applications: £ AC Motor Control £ Servo Motors £ Robotics £ HVAC Inverters Ordering Information: CP15TD1-24A is a 1200 Volt, 15 Ampere DIP-CIB module. 1 Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 CP15TD1-24A DIP-CIB 3Ø Converter + 3Ø Inverter + Brake 15 Amperes/1200 Volts Absolute Maximum Ratings, Tj = 25 °C unless otherwise specified Ratings Symbol CP15TD1-24A Units Junction Temperature Tj -20 to 125 °C Storage Temperature Tstg -20 to 125 °C Mounting Torque, M4 Mounting Screws — 13 in-lb Module Weight Typical — 52 Grams VISO 2500 Volts Collector-Emitter Voltage (G-E Short) VCES 1200 Volts Gate-Emitter Voltage (C-E Short) VGES ±20 Volts Isolation Voltage (60Hz, Sinusoidal, AC 1 Min., Applied Between Pins and Heatsink) Inverter Part Collector Current* (DC, TC = 100°C) Peak Collector Current** (Pulse) IC 15 Amperes ICM 30 Amperes Maximum Collector Dissipation (TC = 25°C) PC 113 Watts IE*** 15 Amperes IEM*** 30 Amperes Collector-Emitter Voltage (G-E Short) VCES 1200 Volts Gate-Emitter Voltage (C-E Short) VGES ±20 Volts IC 10 Amperes Emitter Current* (DC, TC = 64°C) Peak Emitter Current** (Pulse) Brake Part Collector Current* (DC, TC = 100°C) Peak Collector Current** (Pulse) ICM 20 Amperes Maximum Collector Dissipation (TC = 25°C, Tj < 150°C) PC 104 Watts VRRM 1200 Volts IFM 10 Amperes Repetitive Peak Reverse Voltage VRRM 1600 Volts Recommended AC Input Voltage) Ea 440 Volts DC Output Current (Three-phase Rectifying Circuit) IO 15 Amperes IFSM I 2t 245 Amperes A2s Repetitive Peak Reverse Voltage (Clamp Diode Part) Forward Current (Clamp Diode Part, Tj < 150°C) Converter Part Surge Forward Current (1/2 Cycle at 60 Hz, Peak Value, Non-repetitive) I2t for Fusing (Value for 1 Cycle of Surge Current) 252 *TC is measured just underneath the power chip. **Pulse width and repetition rate should be such that the device junction temperature (Tj) does not exceed Tj(max.) rating. ***IE, VEC, trr, and Qrr represent characteristics of the anti-paralleled emitter-to-collector free-wheel diode (FWDi). 2 01/06 Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 CP15TD1-24A DIP-CIB 3Ø Converter + 3Ø Inverter + Brake 15 Amperes/1200 Volts Electrical Characteristics, Tj = 25 °C unless otherwise specified Characteristics Symbol Test Conditions Min. Typ. Max. Units ICES VCE = VCES, VGE = 0V — — 1.0 mA VGE(th) IC = 1.5mA, VCE = 10V 6.5 7.5 8.5 Volts IGES VGE = 20V, VCE = 0V — — 1.0 µA Inverter Part Collector-Cutoff Current Gate-Emitter Threshold Voltage Gate-Emitter Cutoff Current Collector-Emitter VCE(sat) Saturation Voltage* IC = 15A, VGE = 15V, Tj = 25°C — 1.8 2.5 Volts IC = 15A, VGE = 15V, Tj = 125°C — 2.0 — Volts — — 3.24 nF VCE = 10V, VGE = 0V, f = 1MHz — — 0.3 nF — — 0.06 nF VCC = 600V, IC = 15A, VGE = 15V — 100 — nC — — 100 ns — — 75 ns Input Capacitance Cies Output Capacitance Coes Reverse Transfer Capacitance Cres Total Gate Charge QG Turn-on Delay Time td(on) Turn-on Rise Time tr VCC = 600V, IC = 15A, Turn-off Delay Time td(off) VGE = ±15V, RG = 22Ω, — — 300 ns tf Tj = 25°C, — — 400 ns Reverse Recovery Time** trr Inductive Load — 200 — ns Reverse Recovery Charge** Qrr — 0.35 — µC Turn-off Fall Time Emitter-Collector Voltage** VEC IE = 15A, VGE = 0V — 2.7 3.5 Volts External Gate Resistance Rg — 22 — 220 Ω ICES VCE = VCES, VGE = 0V — — 1.0 mA VGE(th) IC = 1.0mA, VCE = 10V 6.5 7.5 8.5 Volts IGES VGE = 20V, VCE = 0V — — 1.0 µA VCE(sat) IC = 10A, VGE = 15V, Tj = 25°C — 1.8 2.5 Volts Brake Part Collector-Cutoff Current Gate-Emitter Threshold Voltage Gate-Emitter Cutoff Current Collector-Emitter Saturation Voltage* IC = 10A, VGE = 15V, Tj = 125°C Input Capacitance Cies Output Capacitance Coes Reverse Transfer Capacitance Cres Total Gate Charge QG Turn-on Delay Time td(on) VCE = 10V, VGE = 0V, f = 1MHz VCC = 600V, IC = 10A, VGE = 15V — 2.0 — Volts — — 2.04 nF — — 0.16 nF — — 0.04 nF — 67 — nC — — 100 ns Turn-on Rise Time tr VCC = 600V, IC = 10A, — — 75 ns Turn-off Delay Time td(off) VGE = ±15V, RG = 33Ω, — — 300 ns Turn-off Fall Time tf Tj = 25°C, — — 400 ns Reverse Recovery Time trr Inductive Load — 200 — ns Reverse Recovery Charge Forward Voltage Drop External Gate Resistance — 0.3 — µC VFM Qrr IF = 10A, Clamp Diode Part — 2.7 3.5 Volts Rg — 33 — 330 Ω *Pulse width and repetition rate should be such as to cause negligible temperature rise. **TC is measured just underneath the power chip. 01/06 3 Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 CP15TD1-24A DIP-CIB 3Ø Converter + 3Ø Inverter + Brake 15 Amperes/1200 Volts Electrical Characteristics, Tj = 25 °C unless otherwise specified Characteristics Symbol Test Conditions Min. Typ. Max. Units Repetitive Reverse Current IRRM VR = VRRM, Tj = 125°C — — 1.0 mA Forward Voltage Drop VFM IF = 15A — 1.1 1.4 Volts Converter Part Thermal and Mechanical Characteristics, Tj = 25 °C unless otherwise specified Characteristics Symbol Test Conditions Min. Typ. Max. Units Rth(c-f) Case-to-Fin, Thermal Grease Applied — 0.047 — °C/W Thermal Resistance, Junction to Case Rth(j-c)Q IGBT Part, Per 1/6 Module — — 1.2 °C/W Thermal Resistance, Junction to Case Rth(j-c)D FWDi Part, Per 1/6 Module — — 1.7 °C/W Thermal Resistance, Junction to Case Rth(j-c)Q IGBT Part — — 1.2 °C/W Thermal Resistance, Junction to Case Rth(j-c)D FWDi Part — — 1.7 °C/W Rth(j-c) Per 1/6 Module — — 1.3 °C/W Resistance Rth TC = 25°C 9.5 10.0 10.5 kΩ B Constant* B(25/100) Resistance at 25°C, 100°C — 3450 — K Common Rating Contact Thermal Resistance Inverter Part Brake Part Converter Part Thermal Resistance, Junction to Case NTC Thermistor Part *B = (InR1 – InR2) / (1/T1 – 1/T2) where R1 is the resistance at T1(K), R2 is the resistance at T2(K). 4 01/06 Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 CP15TD1-24A DIP-CIB 3Ø Converter + 3Ø Inverter + Brake 15 Amperes/1200 Volts COLLECTOR-EMITTER SATURATION VOLTAGE CHARACTERISTICS (INVERTER PART - TYPICAL) 15 20 15 11 10 5 0 0 1 2 3 4 2.0 1.5 1.0 0.5 0 5 10 15 20 25 3.0 2.5 2.0 1.5 1.0 0.5 0 30 Tj = 25°C Tj = 125°C 3.5 0 5 10 15 20 25 COLLECTOR-EMITTER VOLTAGE, VCE, (VOLTS) COLLECTOR-CURRENT, IC, (AMPERES) EMITTER-CURRENT, IE, (AMPERES) CAPACITANCE VS. VCE (INVERTER PART - TYPICAL) SWITCHING TIME VS. COLLECTOR CURRENT (INVERTER PART - TYPICAL) SWITCHING TIME VS. GATE RESISTANCE (INVERTER PART - TYPICAL) 103 104 30 103 103 Coes 102 102 VCC = 600V VGE = ±15V RG = 22Ω Tj = 125°C Inductive Load tf tr 101 Cres VGE = 0V 101 10-1 101 15 20 25 SWITCHING LOSS VS. GATE RESISTANCE (INVERTER PART - TYPICAL) 8 Eon Err 5 10 15 20 Eoff 25 COLLECTOR CURRENT, IC, (AMPERES) 01/06 10 SWITCHING LOSS VS. COLLECTOR CURRENT (INVERTER PART - TYPICAL) 2 0 5 COLLECTOR CURRENT, IC, (AMPERES) 4 0 0 COLLECTOR-EMITTER VOLTAGE, VCE, (VOLTS) VCC = 600V VGE = ±15V RG = 22Ω Tj = 125°C Inductive Load 6 100 102 SWITCHING LOSS, Eon, Eoff, Err, (mJ/PULSE) SWITCHING LOSS, Eon, Eoff, Err, (mJ/PULSE) 8 100 30 SWITCHING TIME, (ns) Cies SWITCHING TIME, (ns) CAPACITANCE, Cies, Coes, Cres, (pF) 2.5 0 5 4.0 VGE = 15V Tj = 25°C Tj = 125°C 13 VCC = 600V VGE = ±15V IC = 15A Tj = 125°C Inductive Load 6 30 4 2 0 0 50 100 Eoff 150 200 GATE RESISTANCE, RG, (Ω) 101 VCC = 600V VGE = ±15V IC = 15A Tj = 125°C Inductive Load tf tr 0 50 100 150 200 250 GATE RESISTANCE, RG, (Ω) Eon Err 102 250 NORMALIZED TRANSIENT THERMAL IMPEDANCE, Zth(j-c') Zth = Rth • (NORMALIZED VALUE) COLLECTOR CURRENT, IC, (AMPERES) VGE = 19V 25 3.0 17 Tj = 25°C COLLECTOR-EMITTER SATURATION VOLTAGE, VCE(sat), (VOLTS) 30 EMITTER-COLLECTOR SATURATION VOLTAGE CHARACTERISTICS (INVERTER PART - TYPICAL) EMITTER-COLLECTOR SATURATION VOLTAGE, VEC, (VOLTS) OUTPUT CHARACTERISTICS (INVERTER PART - TYPICAL) TRANSIENT THERMAL IMPEDANCE CHARACTERISTICS (INVERTER PART - IGBT & FWDi) 100 10-1 10-2 Single Pulse TC = 25°C IGBT FWDi 10-1 100 101 TIME, (s) 5 Powerex, Inc., 173 Pavilion Lane, Youngwood, Pennsylvania 15697-1800 (724) 925-7272 CP15TD1-24A DIP-CIB 3Ø Converter + 3Ø Inverter + Brake 15 Amperes/1200 Volts COLLECTOR-EMITTER SATURATION VOLTAGE CHARACTERISTICS (BRAKE PART - TYPICAL) 3.0 VGE = 15V Tj = 25°C Tj = 125°C 1.2 1.0 COLLECTOR-EMITTER SATURATION VOLTAGE, VCE(sat), (VOLTS) DIODE FORWARD VOLTAGE, VF, (VOLTS) 1.4 0.8 0.6 0.4 0.2 0 0 5 10 15 20 25 DIODE FORWARD CURRENT, IF, (AMPERES) 6 30 4.5 VGE = 15V Tj = 25°C Tj = 125°C 2.5 2.0 1.5 1.0 0.5 0 0 5 EMITTER-COLLECTOR SATURATION VOLTAGE CHARACTERISTICS (BRAKE PART - TYPICAL) EMITTER-COLLECTOR SATURATION VOLTAGE, VEC, (VOLTS) DIODE FORWARD VOLTAGE CHARACTERISTICS (CONVERTER PART - TYPICAL) 10 15 COLLECTOR-CURRENT, IC, (AMPERES) 20 Tj = 25°C Tj = 125°C 4.0 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 0 5 10 15 20 EMITTER-CURRENT, IE, (AMPERES) 01/06