Specifications Before you begin installing your card, please make sure that the following materials have been shipped: • AIMB-744 Pentium® 4/Celeron® processor-based industrial motherboard Standard Motherboard Functions • CPU: Intel® socket 478 Pentium® 4 up to 3.4 GHz, Celeron® D up to 3.06 GHz, Celeron® up to 2.8 GHz and above, FSB 400/533/800 MHz; supports Intel Hyper-Threading technology. Does not support CPU with 1.75V core voltage (Willamete) • 1 AIMB-744 Startup Manual p/n: 2002074412 • L2 Cache: CPU built-in 128/256/512/1024 KB fullspeed L2 cache • 1 CD with driver utility p/n: 2066000E05 • BIOS: Award 4 Mb Flash memory BIOS • 1 FDD cable p/n: 1700340640 • 2 Ultra ATA 66/100 HDD cables p/n: 1701400452 • 2 Serial ATA HDD data cable p/n: 1700071000 • 2 Serial ATA HDD power cable p/n: 1703150102 • FDD interface: Supports up to two FDDs • 1 ATX 12V power converter cable p/n: 170304015K • Serial ports: Four serial RS-232 ports, two DB-9 connectors and two onboard connectors • 1 Dual COM port cable kit p/n: 1701092300 • Keyboard/mouse connector: Supports one standard PS/2 keyboard and mouse • 1 I/O port bracket p/n: 1962015680 • Watchdog timer: 255 level timer intervals • Warranty certificate p/n: 2190000902 • USB (2.0): 4 Universal Serial Bus ports. By setting S1 and S2, the user has two options: • Chipset: Intel 875P with 6300ESB • System Memory: Dual Channel; Four 184-pin DIMM sockets accepts up to 4 GB DDR 266/333/400 SDRAM (PC 2100/2700/3200), ECC supported • SATA/IDE interface: Supports up to two independent Serial ATA hard drives (up to 150MB/s), software SATA RAID1/0, and two IDE hard disk drives or four enhanced IDE devices. BIOS enabled/disabled • Parallel port: One parallel port If any of these items are missing or damaged, contact your distributor or sales representative immediately. Note 1: For detailed contents of the AIMB-744, please refer to the enclosed CD-ROM (in PDF format). Note 2: Acrobat Reader is required to view any PDF file. Acrobat Reader can be downloaded at: www.adobe.com/Prodindex/acrobat/readstep.html (Acrobat is a trademark of Adobe). 1. Default setting: two front panel USB ports (USB4 and USB5, via CN6), and two rear I/O USB ports (USB0 and USB1, on CN31) 2. Optional setting: four rear I/O USB ports (USB2 and USB3 on CN32 are enabled; USB4 and USB5 on CN6 are disabled) For details of setting S1 and S2, please refer to Page 2, S1 & S2: Rear/Front USB port switches. AGP Interface AGP port: One 8x/4x slot, 0.8V and 1.5V Ethernet Interface For more information on this and other Advantech products, please visit our website at: • Chipset: LAN 1:Intel 82547GI (CSA) http://www.advantech.com • Connector: RJ-45 connector x 2 http://www.advantech.com/nc Mechanical and Environmental For technical support and service, please visit our support website at: • Power supply voltage: +3.3 V, +5 V, + 12 V http://service.advantech.com.tw/eservice/ This manual is for the AIMB-744 series Rev. A1. Part No. 2002074412 Printed in Taiwan 3rd Edition June 2005 LAN 2: 82541GI (PCI) • Dimensions (L x W): 304.8 x 243.8 mm (12" x 9.6") • Power requirements: Typical: +3.3V : 8.13A, +5V: 0.57A , +12V: 5.29A (Intel Pentium 4 3.2GHz, 4GB DDR 400) • Operating temperature: 0 ~ 60 C (depending on CPU) • Weight: 0.7 kg (weight of board) AIMB-744 Startup Manual 1 AIMB-744 Socket 478 Intel® Pentium®4/Celeron® Industrial ATX Motherboard Packing List with PCI-X/DDR/AGP/Dual GbE/800 MHz FSB AIMB-744 Socket 478 Intel®Pentium®4/Celeron®D/ Celeron Industrial ATX Motherboard with PCI-X/DDR/ AGP/Dual GbE/800 MHz FSB Jumpers and Connectors The board has a number of jumpers that allow you to configure your system to suit your application. The table below lists the function of each of the jumpers and connectors. Label J1 J2 J5 J6 J7 J8 Function CMOS clear Watchdog timer output selection PCI-X 33/66MHz selection 1 PCI-X 33/66MHz selection 2 VGA controller temperature sensor PCI-X slots 3.3V / 5V selection Label CN1 CN2 CN3 CN4 CN6 CN9 CN10 CN11 CN12 CN14 CN15 CN16 CN17 CN18 CN19 CN21 CN22 Function Primary IDE connector Secondary IDE connector Floppy drive connector Parallel port USB port 4, 5 (shared with CN32) Serial port: COM1 Serial port connector: COM3 PS/2 keyboard and mouse connector External keyboard connector CPU FAN connector System FAN connector 1 Power LED and Keyboard Lock External speaker Reset connector HDD LED connector ATX soft power switch (PS_ON) HW Monitor Alarm Close: Enable OBS Alarm Open: Disable OBS Alarm Serial port connector: COM4 SM BUS Connector PIN1: SMB_DATA PIN2: SMB_CLOCK USB port 0, 1 & LAN1 USB port 2, 3 & LAN2 System FAN connector 2 Serial port: COM2 Line Out, MIC IN connector CD IN (Audio input from CD-ROM) AUX IN connector FP AUDIO connector 8-pin Alarm Board Connector Case Open SerialATA 0 SerialATA 1 Rear/Front USB port switch 1 Rear/Front USB port switch 2 ATX 12V Auxiliary power conn ATX power connector CN23 CN29 CN31 CN32 CN37 CN38 CN55 CN56 CN57 CN59 CN62 CN64 SA0 SA1 S1 S2 ATX1 ATX2 J1: CMOS clear function Pins Result 1-2 (closed) Keep CMOS data* 2-3 (closed) Clear CMOS data 2 AIMB-744 Startup Manual *default setting J2: Watchdog timer output option Closed pins Result 1-2 IRQ11 2-3 System reset * J5&J6: PCI-X 33/66MHz selection Closed Pins Result PCI 33MHz * PCI 66MHz PCI-X 66MHz * default setting J8: PCI-X slots 3.3V / 5V selection Closed Pins Result 3.3 V * 5.0 V * default setting Rear/Front USB port switches Switches S1 S2 Result Front panel USB 2.0. Enable ports 4, 5 on CN6, disable ports 2,3 on CN32. (Default setting) Rear USB 2.0. Enable ports 2, 3 on CN32, disable ports 4,5 on CN6. Remove the sticker on CN32. Software Installation Caution The CD disc contains a driver installer program that will lead you through the installation of various device drivers needed to take full advantage of your motherboard. Danger of explosion if battery is incorrectly replaced. The battery doesn’t need to be charged. Replace only with Advantech-specified batteries. FCC Caution The computer is provided with a battery-powered Real-time Clock circuit. There is a danger of explosion if battery is incorrectly replaced. Replace only with same or equivalent type recommended by the manufacturer. Discard used batteries according to manufacturer's instructions. This device complies with the requirements in part 15 of the FCC rule. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. I/O Connectors AIMB-744 Startup Manual 3 Board Layout: Jumper and Connector Locations 4 AIMB-744 Startup Manual