10KENG3SA

HIGH PERFORMANCE SNAP-IN
SERIES FILTERS
0.84MAX.
21.4MAX.
G3SA
1.22 0.02
31.5 0.5
0.84 MAX.
21.3 MAX.
+0.012
1.12-0
+0.3
28.45-0
ELECTRICAL SCHEMATIC
Cy
Cx
L
Cy
L
O
A
D
0.0315~0.063
0.8~1.6
WIRE LENGTH : 4.0" MIN.
W3EA
N'
N
R0.08MAX.
R2.0MAX.
SUGGESTED MOUNTING CUTOUT
4.0MIN.
100.0MIN.
L'
R
21.90 0.1
0.862 0.004
N
G
0.945 0.02
Suggested thickness of mounting panel is from
0.0315 (0.8) to 0.063 (1.6) inch(mm) of mounting cutout
1.12MAX.
28.4MAX.
L
0.0315~0.063
0.8~1.6
SUGGESTED MOUNTING CUTOUT
1.12MAX.
28.4MAX.
L
45
50
50
40
40
45
R0.08MAX.
R2.0MAX.
+0.04
0.14-0.02
+1.0
3.6-0.5
30
45
50
50
40
40
45
+0.012
1.12-0
+0.3
28.45-0
1.89MAX.
48.0MAX.
1.97 0.04
50.0 1.0
COMMON MODE (L-G) IN 50 OHM SYSTEM
FREQUENCY-MHz
PART NO.
.15
.50
1.0
5.0
10
03KENG3EA/03KENW3EA
15
20
25
40
40
08KENG3EA/08KENW3EA
10
15
20
35
40
10KENG3EA/10KENW3EA
7
12
18
30
30
03KENG3SA/03KENW3SA
15
20
25
40
40
06KENG3SA/06KENW3SA
7
15
20
35
40
10KENG3SA/10KENW3SA
4
12
18
30
30
DIFFERENTIAL MODE (L-L) IN 50 OHM SYSTEM
03KENG3EA/03KENW3EA
5
12
15
40
50
08KENG3EA/08KENW3EA
5
10
15
45
40
10KENG3EA/10KENW3EA
4
12
18
30
30
10
20
35
40
45
03KENG3SA/03KENW3SA
10
25
40
35
40
06KENG3SA/06KENW3SA
10
25
35
30
30
10KENG3SA/10KENW3SA
1.66MAX.
42.16MAX.
MINIMUM INSERTION LOSS IN dB
21.90 0.1
* VDE approved to 6A 250V.
** UL, CSA & VDE approved to 9A 115/250 VAC.
0.862 0.004
+0.04
0.14-0.02
+1.0
3.6-0.5
1.22 0.02
31.5 0.5
24.0 0.5
0.945 0.02
N
G
2.1MAX.
53.4MAX.
L
24.0 0.5
L (mH) Cx (uF) Cy (pF) Lg (uH)
3.1
0.8
0.4
0.1
2200
100
3.1
0.8
0.4
1. Maximum leakage current each
line-to-ground @ 115VAC 60Hz: 0.20mA
@ 250VAC 50Hz: 0.40mA
2. Hipot rating (one minute)
line-to-ground: 2250VDC
line-to-line: 1450VDC
3. Operating frequency: 50/60Hz
4. Rated voltage: 115/250VAC
G'
G
1.89MAX.
48.0MAX.
+0.04
0.14-0.02
+1.0
3.6-0.5
1.22 0.02
31.5 0.5
G3EA
21.3MAX.
MECHANICAL CONSTRUCTION
+0.012
1.12-0
+0.3
28.45-0
W3EA
21.90 0.1
N
G
0.862 0.004
L
24.0 0.5
R: 1M /-R ONLY
0.945 0.02
Lg
2.32 MAX.
59.0 MAX.
IEC INLET FILTERS
COMPONENTS
L
I
N
E
OR
SPECIFICATIONS
INTRODUCTIONS
1. Specially designed with ground choke providing most effective
EMI suppression for high frequency noise (ranged 5MHz-25MHz).
2. Bleeder resistor can be added with suffix "-R" on part numbers.
3. With optional Y capacitor from 100pF to 3300pF.
4. All part numbers are UL recognized, CSA certified and VDE approved.
5.Optional side snap-in mounting clip type with suffix (H) on part numbers.
for 03/06/10KENG3SA series.
PART NO.
03KENG3EA/03KENW3EA
* 08KENG3EA/08KENW3EA
** 10KENG3EA/10KENW3EA
03KENG3SA/03KENW3SA
06KENG3SA/06KENW3SA
10KENG3SA/10KENW3SA
V
D E
R0.08MAX.
R2.0MAX.
0.0315~0.063
0.8~1.6
SUGGESTED MOUNTING CUTOUT
1.12MAX.
28.4MAX.
2-12
G3EA
UNIT: INCH
mm