SERIES SNAP-IN MOUNTING HIGH PERFORMANCE IEC CONNECTOR FILTERS SPECIFICATIONS 1. Specially designed with additional X capacitor providing most effective EMI suppression for low frequency noise (ranged 150KHz-500KHz). 2. Bleeder resistor can be added with suffix "-R" on part numbers. 3. With optional Y capacitor from 100pF to 3300pF. 4. All part numbers are UL recognized, CSA certified and VDE approved. 1. Maximum leakage current each line-to-ground @ 115VAC 60Hz: 0.2mA @ 250VAC 50Hz: 0.4mA 2. Hipot rating (one minute) line-to-ground: 2250VDC line-to-line: 1450VDC 3. Operating frequency: 50/60Hz 4. Rated voltage: 115/250VAC COMPONENTS Cx (uF) 0.1 0.1 0.1 Suggested thickness of mounting panel is from 0.0315 (0.8) to 0.063 (1.6) inch(mm) of mounting cutout Cy (pF) N L VDE approved to 9A/250V G 0.84 MAX. 21.3 MAX. 2200 24.0 0.5 L (mH) 3.1 1.2 0.36 0.945 0.02 PART NO. 03GKNG3E/03GKNW3E 06GKNG3E/06GKNW3E 10GKNG3E/10GKNW3E 30 50 45 50 1.12MAX. 28.4MAX. 4.0MIN. 100.0MIN. 45 40 35 +0.012 1.12-0 +0.3 28.45-0 21.90 0.1 COMMON MODE (L-G) IN 50 OHM SYSTEM FREQUENCY-MHz PART NO. .15 5.0 10 .50 1.0 03GKNG3E/03GKNW3E 20 25 30 40 40 06GKNG3E/06GKNW3E 12 20 25 35 45 10GKNG3E/10GKNW3E 7 10 15 30 35 DIFFERENTIAL MODE (L-L) IN 50 OHM SYSTEM 03GKNG3E/03GKNW3E 5 25 50 55 53 06GKNG3E/06GKNW3E 7 20 35 50 50 10GKNG3E/10GKNW3E 7 9 25 50 45 1.89MAX. 48.0MAX. 1.97 0.04 50.0 1.0 MINIMUM INSERTION LOSS IN dB 0.862 0.004 +0.04 0.14-0.02 +1.0 3.6-0.5 1.22 0.02 31.5 0.5 R0.08MAX. R2.0MAX. 0.0315~0.063 0.8~1.6 SUGGESTED MOUNTING CUTOUT WIRE LENGTH : 4.0" MIN. W3E Cy Cy G L O A D L N G 1.22 0.02 31.5 0.5 N' 21.3MAX. Cx G' MECHANICAL CONSTRUCTION 1.97 0.04 50.0 1.0 R: 1M /-R ONLY +0.012 1.12-0 +0.3 28.45-0 21.90 0.1 Cx 24.0 0.5 R 0.862 0.004 N L' L I N E +0.04 0.14-0.02 +1.0 3.6-0.5 L 0.945 0.02 ELECTRICAL SCHEMATIC 1.89MAX. 48.0MAX. IEC INLET FILTERS INTRODUCTIONS V D E R0.08MAX. R2.0MAX. 0.0315~0.063 0.8~1.6 SUGGESTED MOUNTING CUTOUT 1.12MAX. 28.4MAX. G3E G3E UNIT: INCH mm W3E 2-10