Specification sheet

PSW-240 Series
Specifications
OUTPUT
Features:
• Single and two phase wide input range 180~550VAC
• High efficiency 91% and low power dissipation
• Protections: Short Circuit / Overload / Over Voltage /
Overtemperature
• Cooling by free air convection
• DIN rail mountable
• UL 508 (industrial control equipment) approved
• EN61000-6-2 (EN50082-2) industrial immunity level
• Built-in DC OK relay contact
• 100% full load burn-in test
• 3 year warranty
Cat. No.
PSW-24024
PSW-24048
DC VOLTAGE
RATED CURRENT
CURRENT RANGE
RATED POWER
RIPPLE & NOISE (max)
24V
10A
0 ~ 10A
240W
150mVp-p
48V
5A
0 ~ 5A
240W
150mVp-p
Ripple & noise are measured at 20MHz of bandwidth by using a 12 twisted pair-wire terminated with a 0.1µF & 47µF parallel capacitor.
VOLTAGE ADJ. RANGE
VOLTAGE TOLERANCE
24 ~ 28V
±1.0%
48 ~ 55V
±1.0%
LINE REGULATION
LOAD REGULATION
SETUP, RISE, HOLD UP TIME
±0.5%
±1.0%
800ms, 150ms, 18ms / 400VAC
Tolerance: includes set up tolerance, line regulation and load regulation.
INPUT
VOLTAGE RANGE
180 ~ 550VAC
±0.5%
±1.0%
1500ms, 150ms, 18ms / 230VAC at full load
254 ~ 780VDC
Derating may be needed under low input voltage. Please check the derating curve for more details
PROTECTION
FREQUENCY RANGE
EFFICIENCY (Typ.)
AC CURRENT
INRUSH CURRENT (Typ.)
LEAKAGE CURRENT
OVERLOAD
47 ~ 63Hz
91%
1A / 400VAC
COLD START 50A
≤ 3.5 mA / 530VAC
2A / 230VAC
105 ~ 130% rated output power
Protection type: Constant current limiting, unit will shut down after 3 sec.; auto recovery after 1 minute if the fault condition is removed
OVERVOLTAGE
29 ~ 33V
56 ~ 65V
Protection type: Shut down overvoltage, re-power on to recovery
Under over-voltage condition, If input voltage ≤ 200VAC, the power supply will shut down and then may have auto-recovery
after several seconds
OVERTEMPERATURE
ENVIRONMENT
90˚C ± 5˚C (TSW) detect on heat sink of power switch
Protection type: Shut down overvoltage, recovers automatically after temperature goes down
DC OK RELAY CONTACT RATINGS (max.) 60VDC / 0.3A; 30VDC / 1A; 30VAC / 0.5A resistive load
WORKING TEMP.
-30 ~ +70˚C (Refer to output load derating curve)
Installation clearances: 40mm on top, 20mm on the bottom, 5mm on the left and right side are recommended when loaded
permanently with full power. In case the adjacent device is a heat source, 15mm clearance is recommended.
SAFETY & EMC
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MOUNTING
20 ~ 95% RH non-condensing
-40 ~ +85˚C; 10 ~ 95% RH
±0.03% / ˚C (0 ~ 50˚C)
10 ~ 500Hz, 2G 10min./1cycle, 60 min. each long X,Y, Z axes
Compliance to IEC60068-2-6
SAFETY STANDARDS
UL508 approved
IEC 60950-1 compliant
Design refer to GL
I/P-O/P: 3KVAC I/P-FG: 1.5KVAC O/P-FG :0.5KVAC O/P-DC OK: 0.5KVAC
I/P-O/P, I/P-FG, O/P-FG: ≥ 100M Ohms / 500VDC (25˚C; 70% RH)
EN55022 (CISPR22), Class B
Compliance to EN61000-3-2,-3
Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204; EN 55024; EN61000-6-2; (EN50082-2);
EN61204-3; heavy industry level; criteria A approved;
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
EMI CONDUCTION & RADIATION
HARMONIC CURRENT
EMS IMMUNITY
The power supply is considered a component which will installed into a final equipment. The final
equipment must be re-confirmed that it still meets EMC directives.
OTHERS
MTBF
DIMENSION
PACKING
141.1K hrs min. MIL-HDBK-217K (25˚C)
63x125.2x113.5mm (WxHxD)
1.06Kg; 12pcs / 13.7Kg / 1.06CUFT
All parameters NOT specially mentioned are measured at 400VAC input, rated load and 25˚C of ambient temperature.
For the latest on Altech Power Supply specifications please visit www.altechcorp.com/power.
130
Mechanical Specification
TB2
1
2
3
4
5
6
113. 5
+
3
2
TB1
1
125.2
+V ADJ.
63
1
2
3
Assignment
FG
AC/L2
AC/L1
Assignment
1,2
3,4
5,6
Block Diagram
I/P
EMI FILTER
&
RECTIFIERS
RECTIFIERS
&
FILTER
POWER
SWITCHING
PFC
CIRCUIT
+V
-V
O.C.P.
U.V.P.
O.L.P.
FG
DETECTION
CIRCUIT
PWM & PFC
CONTROL
PFC
CONTROL
O.V.P.
DC OK Relay Contact
Output Derating VS Input Voltage
Derating Curve
100
100
90
80
80
60
70
60
40
50
20
40
-30
0
10
20
30
40
50
60
70 (VERTICAL)
180
200
300
400
450
500
550
Note: All dimensions are in millimeters, to convert to inches multiply by 0.03937.
Altech Corp.® • 35 Royal Road • Flemington, NJ 08822-6000 • Phone (908)806-9400 • FAX (908)806-9490
131