Temperature Sensor TE2 Compact RTD temperature sensors Main features Compact and light weight Available with 4...20 mA transmitter or Pt100 output Available with hygienic as well as industrial process connections Programmable by FlexProgrammer 9701 Applications Food & Beverage Laboratory & Medical Oil & Gas / Chemical Water & Waste water Technical specification Energy Transportation & Logistics Environment Housing Compact Ø 18mm Stainless steel AISI 304 (1.4301) Ambient temperature El. connection M12 or DIN 43650 plug Process temperature -50...250°C Output Pt100 or 4...20mA Protection class M12 : IP67 / DIN 43650 : IP65 Sensor tube material Stainless steel AISI 316L (1.4404) PEEK Humidity <100% RH, condensing Vibrations GL, test 2 Sensor diameter outside Ø 6mm Sensor length < 3 000 mm Standard response tip Fast response tip Ø 6, Ø 4 or Ø 3 -40...125°C -40...85°C Temperature curve Process °C 300 In water In water In water In water 3.0 sec. 2.5 sec. 1.3 sec. <1.0 sec. Sensor element, Pt100 DIN/EN/IEC 60751 Pt100 DIN class B Pt100 1/3 DIN class B Pt100 1/6 DIN class B Pt100 DIN class A ± (0.3 + 0.005 × t) °C ± 1/3 x (0.3 + 0.005 × t) °C ± 1/6 x (0.3 + 0.005 × t) °C ± (0.15 + 0.002 × t) °C Single element Double element 1 × Pt100 2 × Pt100 Connection 4-wire, 2 × 2 wire 250 200 150 100 Design and speci ications subject to change without notice Time constant τ0.5 Sensor tip Ø 6mm Sensor tip Ø 4mm Sensor tip Ø 3mm Conical sensor Pt100 output w. transmitter 85°C 85°C 50 0 0 20 40 60 80 100 °C Ambient with cooling neck EN/2016-04-21 without cooling neck www.baumer.com Data sheet B12.05 TE2 Page 1 / 4 Temperature Sensor TE2 Compact RTD temperature sensors Dimensions (mm) and constructions details Plug M12 with transmit. Plug DIN 43650-A with transmit. Plug DIN 43650-A 70 42 50 26 Plug M12 50 Ø 18 46 Ø18 AF 22 M12x1.5 AF 22 20 24.5 27 G1/2A AF 17 8 AF 22 Cooling neck G1/4 DIN 3852-E G1/2A L Ø6 Ø6 L L Ø6 L Ø6 L Ø6 G½A, ISO 228/1 Code 3 M12x1.5 cone Code 6 Standard Tip Triclamp® Code A Fast response tip Ø6 Conical sensorCode 7 3A DN 38 Code B EN/2016-04-21 ISO 2852 DN 38 Code 9 Design and speci ications subject to change without notice Ø3 PEEK Ø3 L L L L20/L25 Ø6 Ø6 M12x1.5 6 58/63 32 22 21 AF17 G¼A DIN 3852-E Code 8 20 G½A Hygienic Code 4 Without thread Code 1 32 M12x1.5 Code 5 Ø3 or Ø4 mm Ø6 www.baumer.com Ø6 Data sheet B12.05 TE2 Page 2 / 4 Temperature Sensor TE2 Compact RTD temperature sensors Electrical connections Plug DIN 43650-A M12 Plug Transmitter Output Accuracy < 0.25°C (@ ≤ 100°C) Signal span 4...20 mA, 2-wire Sample time < 0.7 sec. Accuracy < 0.1% of signal span Pt100 standard IEC/DIN/EN 60 751-2 Supply range 8...35 VDC RTD measuring current 0.3 mA, continuously Ripple immunity 3 Vms Error detection delay < 10 sec. Load equation RL ≤ (VDC -8)/23 [kOhm] Measuring unit °C or °F Up/Down scaling limits 23 mA/3.5 mA Minimum span 25°C Damping 0...30 sec. Protection ± 35 VDC Protection Reserved polarity protection Surpression 50 and 60 Hz Resolution 12 bit Resolution 14 bit Effect of variations in supply voltage Repeatability < 0.1°C Output current Ripple immunity IEC 770 6.2.4.2 Offset adjustment Max. ± 10°C Isolation, sensor to case 50 VAC (test 500V) Other data Temperature drift 20 sec. Environmental conditions Operating temperature -40...85°C Storage temperature -55...90°C Long-term test IEC 770 6.3.2 EMC data Generic standards EN 61000-6-3, EN 61000-6-2 Product standard EN 61326 Namur NE21 EN/2016-04-21 Power-on time Typ. 0.003% per °C Max. 0.01% per °C 0.01% per volt Design and speci ications subject to change without notice Input www.baumer.com Data sheet B12.05 TE2 Page 3 / 4 Temperature Sensor TE2 Compact RTD temperature sensors Ordering details TE2 TE2 Model – x . x . x x x x . xxxx . x TE2 Compact temperature sensor Sensor tip Not specified Standard Fast Fast For connection code 6 & 7 Normal response Fast response Ø4 mm Fast response Ø3 mm Sensor length 35...300 mm Sensor length 35...300 mm G½ G½ hygienic M12 x 1.5 hygienic M12 x 1.5 hygienic Conical sensor G¼″ (1″, 1½″) (DN15/DN20) Hygienic connection PN40 PN100 PN40 PN40 PEEK cone Ø3 x 5 mm tip PN40 Ø3 x 20 mm or 25 mm sensor tip PN40 PN100 PN40 PN40 PN40 Process connection Tube without connection Nipple, male Nipple, male Nipple, male Nipple, male G⅛″ union nut Nipple, male DN25/DN38 clamp, 3-A Triclamp® ½″, ¾″ 3A/DN38, 3-A ISO 228/1 ISO 228/1 ISO 228/1 ISO 228/1 DIN 3852-E ISO 2852 Sensor element 1 x Pt100 CI. B 2 x Pt100 CI. B 1 x Pt100 CI. 1/3 B 2 x Pt100 CI. 1/3 B 1 x Pt100 CI. 1/6 B 1 x Pt100 CI. A 2 x Pt100 CI. A Cooling neck None Cooling neck Electrical connection M12 plug, 4 pole M12 plug, 4 pole DIN 43650-A DIN 43650-A 0 1 2 3 . 1 3 4 5 6 7 8 9 A B . 1 2 3 4 5 7 8 For 6 mm standard tip only For 6 mm standard tip only For 6 mm standard tip only 0 4 See table page 1 with 4...20 mA transmitter 1 x Pt100 only with 4...20 mA transmitter 1 x Pt100 only 1 2 4 5 Certificates Not specified 0 Sensor tube length 5 mm for connection code 6 20 mm for connection code 7 25 mm for connection code 7 Length in mm (e.g. 60 mm = 0060) . 0005 0020 0025 xxxx Configuration No configuration Configuration of range . EN/2016-04-21 Design and speci ications subject to change without notice 0 C www.baumer.com Data sheet B12.05 TE2 Page 4 / 4