Packaging Information Vishay Semiconductors D2PAK CARRIER TAPE FOR TAPE AND REEL LEFT in millimeters Carrier tape (130 meter long per reel) C7 Ø 1.55 ± 0.05 P2 2.0 ± 0.1 Y 0.40 ± 0.05 C6 P0 4.0 ± 0.1 1.75 ± 0.1 Ø 1.6 ± 0.1 C4 1.57 ± 0.1 2.17 ± 0.1 0.12 MAX. F ± 0.1 C5 C2 CL W ± 0.3 B2 ± 0.1 R 0.3 typical Y P1 ± 0.1 A0 ± 0.1 1.20 C1 K0 ± 0.1 Reel Unreeling direction 30 B0 ± 0.1 C3 Section Y - Y 114 Ø 72 Ø 560 Single winded Level winded NUMBER PACKAGE A0 B0 B2 K0 F P1 W 93-0194-01 D2PAK 10.80 16.00 10.35 4.90 11.50 16.00 24.00 REEL DIAMETER QUANTITY PER REEL 330 800 Notes MATERIAL • Free of heat marks 1. General • No sharp edges allowed • ST : Statistical, Cpk 1.33 • No deformities allowed in wall cavity • 10 sprocket hole pitch cumulative tolerance ± 0.02 mm • Holes, edges and cavities must be free of burrs 0.060 mm (burrs • Camber not to exceed 1 mm in 250 mm • A0 and B0 measured on a plane 0.3 mm above the bottom of the pocket • K0 measured from a plane on the inside bottom of the pocket to the top surface of the carrier • Pocket position relative to sprocket hole measured as true position of pocket, not pocket hole • Measured from centerline of sprocket hole to centerline of pocket • Must also meet requirements of EIA standard #EIA-481A taping of surface mount components for automatic placement 2. Specification shall not come off the tape) PACKAGING 1. General • Each box must be identified with Vishay part number 93-0194-x • Box should be free of foreign particles • Product must be stored at room temperature and clean environment • Certificate of analysis is required per every lot number 2. Material • Conductive black styrenic alloy • Poliestyrene • Surface resistivity of molded material must measure 106 /SQ measured in accordance to procedure given in ASTM D-257 and ASTM D-991 Document Number: 95032 Revision: 09-May-11 For technical questions within your region, please contact one of the following: www.vishay.com [email protected], [email protected], [email protected] 1 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Packaging Information D2PAK Vishay Semiconductors CARRIER TAPE FOR TAPE AND REEL RIGHT in millimeters Carrier tape (130 meter long per reel) C6 Ø 1.55 ± 0.05 P2 2.0 ± 0.1 Y K0 ± 0.1 C7 P0 4.0 ± 0.1 1.20 1.75 ± 0.1 C4 Ø 1.6 ± 0.1 Y 1.57 ± 0.1 2.17 ± 0.1 F ± 0.1 R 0.3 typical A0 ± 0.1 P1 ± 0.1 C3 B2 ± 0.1 C5 CL C2 B0 ± 0.1 W ± 0.3 0.12 MAX. C1 0.40 ± 0.05 Reel Unreeling direction 30 Section Y - Y 114 Ø 72 Ø 560 Single winded Level winded NUMBER PACKAGE A0 B0 B2 K0 F P1 W 93-0195-01 D2PAK 10.80 16.00 10.35 4.90 11.50 16.00 24.00 REEL DIAMETER QUANTITY PER REEL 330 800 Notes MATERIAL PACKAGING 1. General 1. General • ST : Statistical, Cpk 1.33 • 10 sprocket hole pitch cumulative tolerance ± 0.02 mm • Each box must be identified with Vishay part number 93-0195-x • Camber not to exceed 1 mm in 250 mm • Product must be stored at room temperature and clean • A0 and B0 measured on a plane 0.3 mm above the bottom of the pocket • K0 measured from a plane on the inside bottom of the pocket to the top surface of the carrier • Pocket position relative to sprocket hole measured as true position of pocket, not pocket hole • Box should be free of foreign particles environment • Certificate of analysis is required per every lot number 2. Material • Conductive black styrenic alloy • Measured from centerline of sprocket hole to centerline of pocket • Must also meet requirements of EIA standard #EIA-481A taping of surface mount components for automatic placement 2. Specification • Poliestyrene • Surface resistivity of molded material must measure 106 /SQ measured in accordance to procedure given in ASTM D-257 and ASTM D-991 • Free of heat marks • No sharp edges allowed • No deformities allowed in wall cavity • Holes, edges and cavities must be free of burrs 0.060 mm (burrs shall not come off the tape) www.vishay.com 2 For technical questions within your region, please contact one of the following: Document Number: 95032 [email protected], [email protected], [email protected] Revision: 09-May-11 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Packaging Information D2PAK Vishay Semiconductors COVER TAPE FOR CARRIER TAPE in millimeters W Y X ST Y Ø 76.5 ± 1.0 X Section X - X Antistatic layer Pet layer ST 0.055 ± 0.005 Olefin layer Sealant layer Section Y - Y VERSION NUMBER APPLICATION W CARRIER TAPE WIDTH MATERIAL 01 92-5210-14 D2PAK 21.3 ± 0.1 24 Antistatic/treated/transparent/polyester Notes MATERIAL • No sharp edges allowed 1. General • No burrs allowed • ST : Cpk 1.33 2. Specification • Thickness: 0.052 ± 0.005 • Length: 500 m PACKAGING • Tensile strength: 6.00 kg/mm SQ 1. General • Elongation: > 100 % • Each box must be identified with Vishay part number 92-5210-x •Surface resistivity: 10E11 /SQ max. both sides (antistatic) • Box should be free of foreign particles • Peel strength conforms to IRMX specification P01-0074 • POS test range not to exceed 35 grf. Data included on C of C of every lot • Curl 4.5 mm max. Sample length 200 mm Frequency 5 times • Inspection date < one year • Luminous transmittance: 89.8 % • Must also meet all requirements of EIA-standard #EIA-481C, taping of surface mount components for automatic placement • Free of heat marks Document Number: 95032 Revision: 09-May-11 For technical questions within your region, please contact one of the following: www.vishay.com [email protected], [email protected], [email protected] 3 This document is subject to change without notice. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000