350 IR Entrances - Architectural Detail Manual

350/500 IR Entrances
OCTOBER, 2015
FEATURES
Hurricane Resistant Product
Blast Mitigation Product
Features
• 350 IR medium stile has 3-1/2" (88.9) vertical stiles, 3-1/2" (88.9) top and 6-1/2" (165.1)
bottom rails
• 500 IR wide stile has 5" (127) vertical stile, 5" (127) top and 6-1/2" (165.1) bottom rail.
• Door is 1-3/4" (44.5) deep
• Dual moment welded corner construction
• Single acting
• Square stops for 9/16" (14.3) or 1" (25.4) glazing infill for use with Kuraray SentryGlas®
dry glazing
• Offset pivots, butt hinges or continuous geared hinge
• MS locks and 3-point locks or exit device hardware
• Surface mounted or concealed closers
• Architects Classic push/pulls
• Adjustable astragal utilizing pile weathering with polymeric fin at meeting stiles
• Polymeric bulb weatherstripping in door frames
• PermanodicTM anodized finishes in seven choices
• Painted finishes in standard and custom choices
Optional Features
• PanelineTM / PanelineTM EL exit device (Hurricane Resistant applications only)
• Square stops with interior silicone seal for 9/16" (14.3) glazing infill
• Square stops with 3M® VHB interior tape for 9/16" (14.3) or 1" (25.4) glazing infill
• Variety of bottom rails and horizontal cross rails
Product Applications
• 350 IR medium stile and 500 IR wide stile provides extra strength for schools, institutions and other high traffic applications where codes require wind borne debris protection or blast mitigation protection
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
EC 97911-083
1
For specific product applications,
Consult your Kawneer representative.
kawneer.com
ADMA020
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
350/500 IR Entrances
BLANK PAGE
ADMA020
kawneer.com
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
2
OCTOBER, 2015
EC 97911-083
350/500 IR Entrances
OCTOBER, 2015
INDEX
PICTORIAL VIEW................................................................................ 5
DOOR TYPE/SECTION DIMENSIONS................................................ 6
HURRICANE RESISTANT FRAMING DETAILS
IR 500 ENTRANCE......................................................................... 7
IR 501 ENTRANCE......................................................................... 8
FRAMES/SUB-FRAMES
TRIFABTM VG 450/451/ TRIFABTM 601/1600 WALL........................ 9
FRAMING OPTIONS..................................................................... 10
STANDARD ENTRANCE PACKAGES.......................................... 11
ENTRANCE HARDWARE OFFERINGS....................................... 12
PUSH-PULL HARDWARE............................................................. 13
PANELINETM/PANELINETM EL EXIT DEVICES........................ 14-15
CROSS RAIL OPTIONS................................................................ 16
BLAST MITIGATION FRAMING DETAILS
IR 501 ENTRANCE........................................................................ 17
ENTRANCE HARDWARE OFFERINGS.................................. 18-20
LAWS AND BUILDING AND SAFETY CODES GOVERNING THE DESIGN AND USE OF GLAZED ENTRANCE,
WINDOW, AND CURTAIN WALL PRODUCTS VARY WIDELY. KAWNEER DOES NOT CONTROL THE
SELECTION OF PRODUCT CONFIGURATIONS, OPERATING HARDWARE, OR GLAZING MATERIALS,
AND ASSUMES NO RESPONSIBILITY THEREFOR.
Metric (SI) conversion figures are included throughout these details for reference. Numbers in parentheses
(
) are millimeters unless otherwise noted.
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
EC 97911-083
3
The following metric (SI ) units are found in these details:
m –meter
cm – centimeter
mm –millimeter
s –second
Pa –pascal
MPa –megapascal
Kawneer reserves the right to change configurations without prior notice when deemed necessary for product
improvement.
kawneer.com
ADMA020
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
350/500 IR Entrances
BLANK PAGE
ADMA020
kawneer.com
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
4
OCTOBER, 2015
EC 97911-083
350/500 IR Entrances
OCTOBER, 2015
PICTORIAL VIEW
#1 MECHANICAL FASTENING is accomplished
by attaching a 5/16" (7.9) thick extruded aluminum
channel clip to the vertical stile with 1/4"-20 heat
strengthened bolts and 3/16" thick steel nut plates
for a high strength welding base for attachment
horizontal member.
#2 SIGMA* DEEP PENETRATION PLUG WELDS
are made top and bottom after the horizontal
is properly positioned over the channel clip to
help provide the strongest door corner joint
currently available.
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
EC 97911-083
DUAL MOMENT WELDED CORNER CONSTRUCTION
* An arc welding process known as Shielded Inert Gas Metal Arc (SIGMA)
or also known as Metal Inert Gas (MIG).
kawneer.com
ADMA020
#3 SIGMA* FILLET WELDS along both top and
bottom webs of the rail extrusion complete the
welded corner construction.
5
1-3/4"
(44.5)
3
1-3/4"
(44.5)
6-1/2"
(165.1)
2
6-1/2"
(165.1)
TOP
ATTACHMENT
C
L
OF
CYLINDER
C
L
PANIC LOCK
CYLINDER
2
BOTTOM
OF DOOR
ADMA020
STANDARD
EXIT DEVICE
3
2
BOTTOM
OF DOOR
1-3/4"
(44.5)
2
3
3-1/2"
(88.9)
5"
(127)
SINGLE ACTING
SINGLE ACTING
kawneer.com
© Kawneer Company, Inc., 2014
TOP
ATTACHMENT
1
1690 = 41-9/16" (1055.7)
STANDARD
LOCATIONS
C
L OF CRASH BAR FOR
FALCON
C
L OF CRASH BAR FOR KAWNEER
STANDARD EXIT DEVICE
350 IR MEDIUM STILE
1686 = 40" (1016)
1
41-9/16"
(1042.0)
SCALE 3" = 1' 0"
DOOR TYPES/SECTION DIMENSIONS
Hurricane Resistant Product
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
1
5"
(127)
3
44-5/16"
(1125.5)
350/500 IR Entrances
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
1-3/4"
(44.5)
1"
(25.4)
1"
(25.4)
3-1/2"
(88.9)
40-13/16"
(1036.6)
44-5/16"
(1125.5)
6
OCTOBER, 2015
EC 97911-083
500 IR WIDE STILE
1
350/500 IR Entrances
OCTOBER, 2015
EC 97911-083
7
IR 500 ENTRANCE FRAMING DETAILS
Hurricane Resistant Product
SCALE 3" = 1'-0"
NOTE:
1. 350 IR MEDIUM STILE DOORS ARE DETAILED. 500 IR WIDE STILE DOORS MAY ALSO BE USED.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
2. IR 500 FRAMING WITH 9/16" (14.3) GLAZING IS DETAILED WITH THESE DOORS FOR REFERENCE. OTHER GLAZING INFILLS MAY BE USED WITH THE IR 500 SERIES FRAMING. SEE CATALOG SECTION IR 500/501 FRAMING FOR APPROPRIATE DETAILS.
1
2
5
4
8
7
6
4
2
2-1/2"
(63.5)
7
1
575012
3
3
1
TRANSOM HEAD
ELEVATION IS NUMBER KEYED TO DETAILS
5"
(127)
575051
575051
2-1/2"
(63.5)
2-1/2"
(63.5)
1-1/8"
(28.6)
1-1/8"
(28.6)
8*
DOOR JAMB
AT TRANSOM
7*
DOOR JAMB
AT TRANSOM
575051
2
DOOR WITH TRANSOM
575051
3/32"
(2.4)
3-1/2"
(88.9)
3-1/2"
(88.9)
2-1/2"
(63.5)
3/32"
(2.4)
2-1/2"
(63.5)
6-1/2"
(165.1)
575035
575035
© Kawneer Company, Inc., 2014
200795
6
DOOR JAMB
4
DOOR JAMB
069139
11/16"
(17.5)
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
575035
575035
3-1/2"
(88.9)
2-1/2"
1/8" (63.5)
(3.2)
575033
575033
575022
575004
3-1/2"
(88.9)
1/8"
(3.2)
3-1/2"
(88.9)
* STEEL REINFORCING AS REQUIRED.
5
PAIR OF DOORS
kawneer.com
3
THRESHOLD
ADMA020
350/500 IR Entrances
8
OCTOBER, 2015
IR 501 ENTRANCE FRAMING DETAILS
Hurricane Resistant Product
EC 97911-083
SCALE 3" = 1'-0"
NOTE:
1. 350 IR MEDIUM STILE DOORS ARE DETAILED. 500 IR WIDE STILE DOORS MAY ALSO BE USED.
1
2
5
4
8
7
6
4
2
2-1/2"
(63.5)
7
1
575112
3
1
TRANSOM HEAD
3
ELEVATION IS NUMBER KEYED TO DETAILS
5"
(127)
575051
575051
575133
575122
575104
1-1/8"
(28.6)
2-1/2"
(63.5)
8
DOOR JAMB
AT TRANSOM
7
DOOR JAMB
AT TRANSOM
575051
2
DOOR WITH TRANSOM
3/32"
(2.4)
2-1/2"
(63.5)
3-1/2"
(88.9)
3-1/2"
(88.9)
3/32"
(2.4)
6-1/2"
(165.1)
575135
575135
575051
2-1/2"
(63.5)
200795
6
DOOR JAMB
4
DOOR JAMB
11/16"
(17.5)
069139
3-1/2"
(88.9)
1/8"
(3.2)
3
THRESHOLD
3-1/2"
(88.9)
5
PAIR OF DOORS
ADMA020
kawneer.com
© Kawneer Company, Inc., 2014
1-1/8"
(28.6)
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
2-1/2"
(63.5)
3-1/2"
(88.9)
575135
1/8"
(3.2)
575135
2-1/2"
(63.5)
575133
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
2. IR 501 FRAMING WITH 1-5/16" (33.3) GLAZING IS DETAILED WITH THESE DOORS FOR REFERENCE. OTHER GLAZING INFILLS MAY BE USED
WITH THE IR 501 SERIES FRAMING. SEE CATALOG SECTION IR 500/501 FRAMING FOR APPROPRIATE DETAILS.
3-1/2"
(88.9)
1-3/4"
(44.5)
1/8"
(3.2)
1/8"
(3.2)
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
3-1/2"
(88.9)
2"
(50.8)
1/8"
(3.2)
1-1/16"
(27)
3/8"
(9.5)
3-1/2"
(88.9)
3-1/2"
(88.9)
2"
(50.8)
1/8"
(3.2)
1-3/4"
(44.5)
1/8"
(3.2)
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
OCTOBER, 2015
kawneer.com
350/500 IR Entrances
EC 97911-083
SCALE 3" = 1'-0"
TRIFABTM VG 450 FRAMING
3/32"
(2.4)
1-3/4"
(44.5)
3-1/2"
(88.9)
3/32"
(2.4)
2"
(50.8)
TRIFABTM 601 FRAMING
3/32"
(2.4)
2"
(50.8)
ADMA020
3-1/2"
(88.9)
1600 WALL SUB FRAMING
3/32"
(2.4)
7/8"
(22.3)
3-1/2"
(88.9)
9
TRIFABTM VG 450/451/TRIFABTM 601 FRAMES / 1600 WALL SUB-FRAMES
Hurricane Resistant Product
TRIFABTM VG 451 FRAMING
3-1/2"
(88.9)
DLO
575020
DLO
041045
IR 500
C.O.C. TRANSOM BAR
3-1/2"
(88.9)
575063
5"
(127)
IR 500 RADIUS HEAD
ADMA020
DLO
5/8"
(15.9)
3-1/2"
(88.9)
Trifab VG 450
C.O.C. TRANSOM BAR
3-1/2"
(88.9)
2"
(50.8)
1/8"
(3.2)
1-3/4"
(44.5)
1/8"
(3.2)
450022
450022
575162
575064
575065
450079
041045
041045
Trifab VG 451
C.O.C. TRANSOM BAR
5"
(127)
5"
(127)
575160
5"
(127)
575161
575162
575104
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
1-1/2"
(38.1)
5/8"
(15.9)
575061
1/8"
(3.2)
2-1/2"
(63.5)
1/8"
(3.2)
SCALE 3" = 1' - 0"
FRAMING OPTIONS
Hurricane Resistant Product
5"
(127)
575120
069177
069177
IR 500
OPTIONAL TRANSOM BAR WITH
SINGLE ACTING APPLIED STOP
IR 501
OPTIONAL TRANSOM BAR WITH
SINGLE ACTING APPLIED STOP
575065
575163
575164
5"
(127)
IR 501 RADIUS HEAD
kawneer.com
© Kawneer Company, Inc., 2014
3-1/2"
(88.9)
DLO
1-1/2"
(38.1)
350/500 IR Entrances
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
1/8"
(3.2)
575004
3-1/2"
(88.9)
2-1/2"
(63.5)
1/8"
(3.2)
2-1/2"
(63.5)
575060
2-1/2"
(63.5)
3-1/2"
(88.9)
2-1/2"
(63.5)
450022
DLO
2-1/2"
(63.5)
DO
10
OCTOBER, 2015
EC 97911-083
450022
041045
IR 501
C.O.C. TRANSOM BAR
350/500 IR Entrances
OCTOBER, 2015
EC 97911-083
11
STANDARD ENTRANCE PACKAGES
Hurricane Resistant Product
Blast Mitigation Product
3/8"
(9.5)
SCALE 3" = 1' 0"
1/8"
(3.2)
MASONRY OPENING
1/8"
(3.2)
3/16"
(4.3)
1/2"
(12.7)
kawneer.com
1/8"
(3.2)
OVERALL FRAME
3/8"
(9.5)
DOOR OPENING
3/32"
(2.4)
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
OVERALL FRAME
3/8"
(9.5)
DOOR OPENING
MASONRY OPENING
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
DIMENSIONS ARE NOMINAL
3/32"
(2.4)
STANDARD SIZES (IR 500 AND IR 501 FRAMES)
WITHOUT TRANSOM
Door Opening Dimension
Overall Frame Dimension
Masonry Opening Dimension
3' 0" x 7' 0" ( 914 x 2134)
3' 5" x 7' 2-1/2" (1041 x 2197)
3' 5-3/4" x 7' 2-7/8" (1064 x 2207)
3' 6" x 7' 0" (1067 x 2134)
3' 11" x 7' 2-1/2" (1194 x 2197)
3' 11-3/4" x 7' 2-7/8" (1213 x 2207)
6' 0" x 7' 0" (1829 x 2134)
6' 5" x 7' 2-1/2" (1956 x 2197)
6' 5-3/4" x 7' 2-7/8" (1975 x 2207)
WITH TRANSOM
Door Opening Dimension
Masonry Opening Dimension
Masonry Opening Dimension
Unchanged from above.
Add 3' 2-1/2" (978) to above heights.
Add 3' 2-1/2" (978) to above heights.
STANDARD SIZES (TRIFABTM VG 450 CENTER FRAMES)
WITHOUT TRANSOM
Door Opening Dimension
Overall Frame Dimension
Masonry Opening Dimension
3' 0" x 7' 0" ( 914 x 2134)
3' 3-1/2" x 7' 1-3/4" (1003 x 2178)
3' 4-1/4" x 7' 2-1/8" (1022 x 2188)
3' 6" x 7' 0" (1067 x 2134)
3' 9-1/2" x 7' 1-3/4" (1156 x 2178)
3' 10-1/4" x 7' 2-1/8" (1175 x 2188)
6' 0" x 7' 0" (1829 x 2134)
6' 3-1/2" x 7' 1-3/4" (1918 x 2178)
6' 4-1/4" x 7' 2-1/8" (1937 x 2188)
WITH TRANSOM
Door Opening Dimension
Masonry Opening Dimension
Masonry Opening Dimension
Unchanged from above.
Add 3' 1-3/4" (959) to above heights.
Add 3' 1-3/4" (959) to above heights.
STANDARD SIZES (TRIFABTM VG 451, AND TRIFABTM 601 CENTER FRAMES)
WITHOUT TRANSOM
Door Opening Dimension
Overall Frame Dimension
Masonry Opening Dimension
3' 0" x 7' 0" ( 914 x 2134)
3' 4" x 7' 2" (1016 x 2184)
3' 4-3/4" x 7' 2-3/8" (1035 x 2194)
3' 6" x 7' 0" (1067 x 2134)
3' 10" x 7' 2" (1168 x 2184)
3' 10-3/4" x 7' 2-3/8" (1187 x 2194)
6' 0" x 7' 0" (1829 x 2134)
6' 4" x 7' 2" (1930 x 2184)
6' 4-3/4" x 7' 2-3/8" (1949 x 2194)
WITH TRANSOM
Door Opening Dimension
Masonry Opening Dimension
Masonry Opening Dimension
Unchanged from above.
Add 3' 2" (965) to above heights.
Add 3' 2" (965) to above heights.
STANDARD SIZES (1600 WALL SUB FRAMES)
WITHOUT TRANSOM
Door Opening Dimension
Overall Frame Dimension
Masonry Opening Dimension
3' 0" x 7' 0" ( 914 x 2134)
3' 6-3/4" x 7' 4-3/8" (1086 x 2245)
3' 7-3/4" x 7' 4-7/8" (1111 x 2257)
3' 6" x 7' 0" (1067 x 2134)
4' 3/4" x 7' 4-3/8" (1238 x 2245)
4' 1-3/4" x 7' 4-7/8" (1264 x 2257)
6' 0" x 7' 0" (1829 x 2134)
6' 6-3/4" x 7' 4-3/8" (2000 x 2245)
6' 7-3/4" x 7' 4-7/8" (2026 x 2257)
WITH TRANSOM
Door Opening Dimension
Masonry Opening Dimension
Masonry Opening Dimension
Unchanged from above.
Add 3' 2-1/2" (978) to above heights.
Add 3' 2-1/2" (978) to above heights.
ADMA020
350/500 IR Entrances
OCTOBER, 2015
4
MAXIMUM
DOOR SIZE
MS 1850
3-Point Lock
(Active leaf)
Single 4'-0" x 8'-0" (1219.2 x 2438.4)
Pair 8'-0" x 8'-0" (2438.4 x 2438.4)
± 70 PSF
Flushbolts
(Inactive leaf)
Single 3'-6" x 7'-0" (1066.8 x 2133.6)
± 90 PSF
MS 1850
3-Point Lock
(Active leaf)
Adams Rite 2180
2 Point Dead Lock
(Inactive leaf)
4
MAXIMUM
DESIGN
PRESSURE
Single 4'-0" x 8'-0" (1219.2 x 2438.4)
Pair 8'-0" x 8'-0" (2438.4 x 2438.4)
± 90 PSF
4
GLAZING STOP
OPTIONS
GLASS
THICKNESS
Offset Pivots
Butt Hinges
Continuous Hinge
1, 2, 3
9/16" (14.3)
2, 3
1" (25.4)
1, 2, 3
9/16" (14.3)
2, 3
1" (25.4)
Offset Pivots
Butt Hinges
Continuous Hinge
1, 2, 3
9/16" (14.3)
2, 3
1" (25.4)
Offset Pivots
Butt Hinges
Continuous Hinge
1, 2, 3
9/16" (14.3)
2, 3
1" (25.4)
Offset Pivots
Butt Hinges
Continuous Hinge
Kawneer 1686
Concealed Rod
Exit Device
(EL option)
Single 4'-0" x 8'-0" (1219.2 x 2438.4)
Pair 8'-0" x 8'-0" (2438.4 x 2438.4)
± 90 PSF
Paneline
Concealed Rod
Exit Device
(EL option)
Single 4'-0" x 8'-0" (1219.2 x 2438.4)
Pair 8'-0" x 8'-0" (2438.4 x 2438.4)
± 70 PSF
Adams Rite G86
Concealed Rod
Exit Device
Single 4'-0" x 8'-0" (1219.2 x 2438.4)
Pair 8'-0" x 8'-0" (2438.4 x 2438.4)
± 70 PSF
Offset Pivots
Butt Hinges
Continuous Hinge
1, 2, 3
9/16" (14.3)
2, 3
1" (25.4)
Calibre 9100
Concealed Rod
Exit Device
Single 4'-0" x 8'-0" (1219.2 x 2438.4)
Pair 8'-0" x 8'-0" (2438.4 x 2438.4)
± 70 PSF
Offset Pivots
Butt Hinges
Continuous Hinge
1, 2, 3
9/16" (14.3)
2, 3
1" (25.4)
Falcon HH1690
Concealed Rod
Exit Device
(EL option)
Single 4'-0" x 8'-0" (1219.2 x 2438.4)
Pair 8'-0" x 8'-0" (2438.4 x 2438.4)
Offset Pivots
Butt Hinges
Continuous Hinge
1, 2, 3
9/16" (14.3)
± 65 PSF
2, 3
1" (25.4)
Jackson 2086
Concealed Rod
Exit Device
Single 4'-0" x 8'-0" (1219.2 x 2438.4)
Pair 8'-0" x 8'-0" (2438.4 x 2438.4)
± 90 PSF
Offset Pivots
Butt Hinges
Continuous Hinge
1, 2, 3
9/16" (14.3)
2, 3
1" (25.4)
Sargent AD8400
Concealed Rod
Exit Device
Single 4'-0" x 8'-0" (1219.2 x 2438.4)
Pair 8'-0" x 8'-0" (2438.4 x 2438.4)
± 65 PSF
Offset Pivots
Butt Hinges
Continuous Hinge
1, 2, 3
9/16" (14.3)
2, 3
1" (25.4)
Von Duprin HH9947
Concealed Rod
Exit Device
Single 4'-0" x 8'-0" (1219.2 x 2438.4)
Pair 8'-0" x 8'-0" (2438.4 x 2438.4)
± 65 PSF
Offset Pivots
Butt Hinges
Continuous Hinge
1, 2, 3
9/16" (14.3)
2, 3
1" (25.4)
± 50 PSF
(Zone 3 only)
Offset Pivots
Butt Hinges
Continuous Hinge
1, 2, 3
9/16" (14.3)
2, 3
1" (25.4)
± 50 PSF
Offset Pivots
Butt Hinges
Continuous Hinge
1, 2, 3
9/16" (14.3)
2, 3
1" (25.4)
TM
4
HINGING
OPTIONS
Von Duprin 98/99 XP
Single 3'-6" x 7'-6" (1066.8 x 2286)
Concealed Rod
Pair 7'-0" x 7'-6" (2133.6 x 2286)
Exit Device
Corbin Russwin
ED5200SA
Rim Device
Single 4'-0" x 8'-0" (1219.2 x 2438.4)
Pair 8'-0" x 8'-0" (2438.4 x 2438.4)
Glazing Stop Options:
1 - Structural silicone with 0.090 Kuraray or Eastman PVB inter layer or 0.090 Kuraray Sentry Glas® inter layer.
2 - 3M VHB structural tape with 0.090 Kuraray or Eastman PVB inter layer or 0.090 Kuraray Sentry Glas® inter layer.
3 - Dry glazing gasket with 0.090 Kuraray Sentry Glas® inter layer, only for 9/16" (14.3) infill with design pressure < or = 90 PSF.
4 - Available in 6'-0" x 9'-0" pairs.
ADMA020
kawneer.com
© Kawneer Company, Inc., 2014
LOCKING
OPTIONS
EC 97911-083
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
ENTRANCE HARDWARE OFFERINGS
Hurricane Resistant Product
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
12
350/500 IR Entrances
OCTOBER, 2015
EC 97911-083
13
PUSH-PULL HARDWARE
REFER TO HARDWARE SECTION FOR COMPLETE HARDWARE INFORMATION.
ARCHITECTS CLASSIC (PUSH PULL SETS)
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
SINGLE ACTING DOORS USE A PULL HANDLE AND PUSH BAR AS STANDARD
CP-II/CP-II
CO-9/CO-9
CO-12/CO-12
CO-9/CP-II
CO-12 /CP-II
CO-9/CP
CO-12/CP
ARCHITECTS CLASSIC (COMPONENTS)
STYLE CO-12
PULL
STYLE CO-9
PULL
KAWNEER PANELINE
/ PANELINE
TM
EL
9-5/16"
(236.5)
Overall with stops
TM
STYLE "CO-9"
PULL
© Kawneer Company, Inc., 2014
STYLE CP PUSH BAR
STYLE CP-II PUSH BAR
EXIT DEVICES AND PULLS
EXIT DEVICES
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
CP/CP
STYLE "CO-12"
PULL
CONCEALED ROD
Falcon 1690
Falcon EL 1690
CONCEALED ROD
Jackson 2086
CONCEALED ROD
Calibre 9100
CONCEALED ROD
Sargent 8400AD
STYLE"CPN" PULL ON
EXTERIOR OF DOOR
CONCEALED ROD
Von Duprin
9947HH
EXTERIOR VIEW OF 350 IR DOOR (500 IR SIMILAR)
"CPN" PULL AND OPTIONAL CYLINDER GUARD SHOWN.
SEE PAGE 14 AND 15 FOR COMPLETE
PANELINETM INFORMATION
kawneer.com
CONCEALED ROD
Adams Rite G86
CONCEALED ROD
Kawneer 1686
Kawneer 1686 EL
ADMA020
RIM DEVICE
Von Duprin 98/99 XP
RIM DEVICE
Corbin Russwin
ED5200SA
350/500 IR Entrances
14
OCTOBER, 2015
PANELINE / PANELINE EL EXIT DEVICE
Hurricane Resistant Product
TM
EC 97911-083
TM
SCALE 3" = 1' - 0"
PANELINETM EXIT DEVICE
The Optional PanelineTM EL device is designed for electrified access control and is compatible with most key pad
and card reader systems.
1-1/8"
(27.8)
1
PUSH
8-1/4"
(209.6)
7-1/8"
(181.0)
PanelineTM uses mortise cylinder in lieu of the normal rim-type.
1
INTERIOR VIEW
LOCK STILE TRIM FILLER WIDTH
VARIES WITH STILE WIDTH
INTERIOR ELEVATION
PUSH
5-7/8"
(149.2)
1'-11 5/16" (592.1)
ACTIVE PUSH PANEL
FIXED WIDTH
1"
(25.4)
DOGGING LOCK
(TYPICAL)
CROSS RAIL
WITH EXIT DEVICE
AND CPN PULL HANDLE
PIVOT STILE TRIM FILLER WIDTH
VARIES WITH DOOR WIDTH
36-1/8"
(917.8)
TO BOTTOM
OF DOOR
PANELINETM EL COMPONENTS
DOOR OPENING WIDTH
4'-0" (1219.2) MAX. - 2'-10 13/32" (873.9) MIN.
3'-0" (914.6) ADA MIN.
POWER TRANSFER
INTERMEDIATE BUTT HINGE
POWER TRANSFER
INTERMEDIATE OFFSET PIVOT
EXTERIOR VIEW
EXTERIOR VIEW OF 350 IR DOOR (500 IR SIMILAR) WITH
"CPN" PULL AND OPTIONAL CYLINDER GUARD SHOWN
ELECTRIC POWER TRANSFER
(EPT)
ADMA020
SP-1000X POWER SUPPLY
kawneer.com
© Kawneer Company, Inc., 2014
1 3/4"
(44.5)
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
See Hardware Section for complete description of Paneline hardware, including finish of units.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
The PanelineTM concealed rod exit device will accommodate variations in door width as shown in the following
illustrations.
350/500 IR Entrances
OCTOBER, 2015
EC 97911-083
PANELINETM EXIT DEVICE
PANELINETM EXIT DEVICE
See Hardware Section for complete description of PanelineTM hardware, including finish of units.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
PanelineTM uses mortise cylinder in lieu of the normal rim-type.
1-23/32"
(43.8)
1-1/8"
(27.8)
1/8"
(3.2)
PUSH
PUSH
1 or 2*
2
1 or 2*
* ALTERNATE CROSSRAIL FOR VESTIBULE DOORS
(Without Exit Device or Lock)
1"
(25.4)
ACTIVE DOOR
INACTIVE DOOR
8-1/4"
(209.6)
1
7-1/8"
(181.0)
INTERIOR ELEVATION
CROSS RAIL
WITH EXIT DEVICE
AND CPN PULL HANDLE
36-1/8"
(917.6)
TO BTM
OF DOOR
(FIXED LOCATION)
CROSS RAIL
WITH
FIXED PANEL
PIVOT STILE TRIM FILLER WIDTH
VARIES WITH DOOR WIDTH
DOGGING LOCK
(TYPICAL)
PUSH
PUSH
STYLE"CPN" PULL ON
EXTERIOR OF DOOR
350 IR DOOR
DOOR OPENING WIDTH
8'-0" (2438.4) MAX. - 5'-9 5/16" (1761.0) MIN.
6'-0" (1828.8) ADA MIN.
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
INTERIOR VIEW
PUSH
PUSH
500 IR DOOR
EXTERIOR VIEW
DOOR OPENING WIDTH
8'-0" (2438.4) MAX. - 6'-0" (1828.8) MIN.
6'-0" (1828.8) ADA MIN.
kawneer.com
EXTERIOR VIEW OF 350 IR DOOR (500 IR SIMILAR) WITH
"CPN" PULL AND STANDARD CYLINDER GUARD SHOWN
ADMA020
15
16
350/500 IR Entrances
OCTOBER, 2015
CROSS RAIL OPTIONS
Hurricane Resistant Product
EC 97911-083
SCALE 3" = 1' 0"
HORIZONTAL CROSS RAILS
8-1/4" CROSS RAIL
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
6" CROSS RAIL
8-1/4"
(209.6)
6"
(152.4)
3-1/2"
(88.9)
3-1/2" CROSS RAIL
200058
200053
200059
9/16" IMPACT
GLASS STOP
(3M Tape Glaze)
9/16" IMPACT
GLASS STOP
(Structural Silicone Glaze )
1" IMPACT
GLASS STOP
(Dry Glaze)
1" IMPACT
GLASS STOP
(3M Tape Glaze)
BOTTOM RAILS
6-1/2"
(165.1)
7-1/2"
(190.5)
10"
(254)
Rail height shown may be used on 350 IR and 500 IR doors.
200032
200034
200038
6-1/2" BOTTOM RAIL
(STANDARD)
7-1/2" BOTTOM RAIL
10" BOTTOM RAIL
ADMA020
kawneer.com
© Kawneer Company, Inc., 2014
9/16" IMPACT
GLASS STOP
(Dry Glaze)
(STANDARD)
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
INFILL OPTIONS
350/500 IR Entrances
OCTOBER, 2015
EC 97911-083
17
IR 501 ENTRANCE FRAMING DETAILS
Blast Mitigation Product
SCALE 3" = 1'-0"
2. IR 501 FRAMING WITH 1-5/16" (33.3) GLAZING IS DETAILED WITH THESE DOORS.
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
1
8
1
9
2
8
2-1/2"
(63.5)
NOTE:
1. 350 IR MEDIUM STILE DOORS ARE DETAILED. 500 IR WIDE STILE DOORS MAY ALSO BE USED.
575104
2
575103
1
TRANSOM HEAD
5"
(127)
7
6
3
575160
5
575161
3
4
2-1/2"
(63.5)
1/8"
(3.2)
5
4
575310
451548
575062
3-1/2"
(88.9)
ELEVATION IS NUMBER KEYED TO DETAILS
041045
575051
575051
575133
575133
575310
1-1/8"
(28.6)
1-1/8"
2-1/2"
(28.6)
(63.5)
3-1/2"
(88.9)
2-1/2"
(63.5)
9
DOOR JAMB
AT TRANSOM
8
DOOR JAMB
AT TRANSOM
575051
575051
575310
3
CROSS RAIL
575052
3/32"
(2.4)
2-1/2"
(63.5)
3-1/2"
(88.9)
3-1/2"
(88.9)
5
DOOR JAMB
3/32"
(2.4)
2-1/2"
(63.5)
7
DOOR JAMB
6-1/2"
(165.1)
575135
© Kawneer Company, Inc., 2014
200795
069139
3-1/2"
(88.9)
1/8"
(3.2) 3-1/2"
(88.9)
11/16"
(17.5)
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
575135
575052
2
DOOR WITH TRANSOM
6
PAIR OF DOORS
kawneer.com
ADMA020
4
THRESHOLD
350/500 IR Entrances
OCTOBER, 2015
EC 97911-083
LOCKING
OPTIONS
Kawneer 1686
Concealed Rod
Exit Device
MAXIMUM
DOOR SIZE
Single 4'-0" x 8'-0" (1219.2 x 2438.4)
Pair 8'-0" x 8'-0" (2438.4 x 2438.4)
MAXIMUM
BLAST
LOADING
Peak Pressure:
5.8 PSF
Impulse:
41 PSI/M-SEC
HINGING
OPTIONS
GLAZING STOP
OPTIONS
GLASS
THICKNESS
Offset Pivots
1
9/16" (14.3)
Test conditions shown. Other conditions may be supported through calulation.
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
Glazing Stop Options:
1 - Structural silicone with 0.060 Kuraray or Eastman PVB inter layer.
ADMA020
kawneer.com
© Kawneer Company, Inc., 2014
ENTRANCE HARDWARE OFFERINGS
Blast Mitigation Product
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
18
350/500 IR Entrances
OCTOBER, 2015
EC 97911-083
ENTRANCE HARDWARE OFFERINGS
Hurricane Resistant Product
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
STANDARD
OPTIONAL
Doors
Medium stile 350 IR
Wide stile 500 IR
Door Sizes
Maximum size shown on page 11.
Maximum door sizes are determined by hardware type, refer to
specific hardware for size limitations.
Glass Stops
Square stops for 9/16" (14.3) infill, interior and exterior snap in Square stops for 9/16" (14.3) or 1" (25.4) infill, interior screw
glass stop.
applied glass stop with 3M VHB structural tape.
Square stops for 9/16" (14.3) infill, interior screw applied glass
stop with silicone seal.
Square stops for 1" (25.4) infill, interior and exterior snap in
glass stop.
Door Frames
IR 500 2-1/2" x 5" (63.5 x 127)
*IR 501 2-1/2" x 5" (63.5 x 127)
*IR 501T/UT 2-3/4" x 5" (69.9 x 127)
TrifabTM VG 450 1-3/4" x 4-1/2" (44.5 x 114.3)
TrifabTM VG 451 2" x 4-1/2" (50.8 x 114.3)
TrifabTM VG 451T 2" x 4-1/2" (50.8 x 114.3)
TrifabTM 601/601T 2" x 6" (50.8 x 152.4)
1600 sub-frame with door jamb adaptors and sub-head
Push-Pulls
Single Acting:
Single Acting:
Architects Classic Hardware "CO-9" Pull and
"CP-II" Push Bar.
Architects Classic Hardware "CO-9" Pull and
"CP" Push Bar.
Architects Classic Hardware
"CO-12" and "CP-II" push bar.
Architects Classic Hardware
"CO-12" and "CP" push bar.
Architects Classic Hardware
"CO-9"/"CO-9" Pulls.
Architects Classic Hardware
"CO-12"/"CO-12" Pulls.
Door Closers
Single Acting:
Norton 1601 Adjustable or 1601 BF
Adjustable Surface Closer with back-check,
with or without adjustable hold open.
Standard concealed overhead closer with
single acting offset arm.
Single Acting:
LCN 4040 surface closer with or without
adjustable hold-open.
LCN 2010, 2030 or 5010 concealed
overhead closers with or without hold-open.
LCN 1260 adjustable surface closer.
Norton 8100 surface closer with a 50%
spring power adjustment (for opening forces
of less than 8 pounds). Closer is available
with standard back-checks and with or
without the hold-open feature.
International single acting concealed
overhead closer.
Falcon SC 60 Surface closer.
Hinging
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
19
Single Acting:
Kawneer top and bottom offset pivots
(or) Kawneer top and bottom 4 1/2" x 4"
(114.3 x 101.6) ball bearing butt hinge with
non-removable pin (NRP) (or) Kawneer
continuous gear hinge.
---
Kawneer intermediate offset pivot (or)
Kawneer 4-1/2" x 4" (114.3 x 101.6) ball
bearing butt hinge with non-removable pin
(NRP).
---
Intermediate
Pivots/Butts
Single Acting:
Locking
MS 1850 Deadbolt 3-Point Lock with 4016 Top Bolt and
4056 Bottom Bolt. Hurricane Resistant Flush Bolts required on
pairs.
NOTE:
*IR 501 door frame uses IR 500 door jamb with IR 501 filler.
kawneer.com
ADMA020
Adams Rite 2180 Dead Lock Flush Bolt for pair only.
350/500 IR Entrances
OCTOBER, 2015
ENTRANCE HARDWARE OFFERINGS
EC 97911-083
STANDARD
OPTIONAL
Doors
Medium stile 350 IR
Thresholds
A 1/2" x 4" (12.7 x 101.6) aluminum mill
finish threshold.
Weathering
Single
Acting:
Exit Device
Kawneer 1686 Concealed Rod Exit
Device with or without a mortised type
cylinder.
Kawneer PanelineTM Conc. Rod Exit Device
Kawneer PanelineTM EL Conc. Rod Exit Device
Jackson 2086 Concealed Rod Exit Device
Adams Rite G86 Conc. Rod Exit Device
Calibre 9100 Conc. Rod Exit Device
Falcon HH1690 Conc. Rod Exit Device
Sargent 8400AD Concealed Rod Exit Device
Von Duprin HH9947 Conc. Rod Exit Device
Von Duprin 98/99 XP Rim Device
Corbin Russwin ED5200SA Rim Device
Exit Device Pulls:
Architects Classic style "CO-9" Pull with
Kawneer 1686 exit device.
Architects Classic style "CPN" Pull
for PanelineTM and PanelineTM EL exit
devices.
Optional Exit Device Pulls:
Architects Classic style "CO-12" Pull with Kawneer 1686 exit device.
Weathering system in the
door and frame consisting of a
dense, bulb polymeric material,
which remains resilient and
retains its weathering ability
under temperature extremes.
(The system is complete with
an optional EPDM blade gasket
sweep strip applied to the
bottom door rail with concealed
fasteners).
Wide stile 500 IR
--Bottom Door Sweep
Laws and building and safety codes governing the design and use of glazed
entrance, window, and curtain wall products vary widely. Kawneer does not control
the selection of product configurations, operating hardware, or glazing materials,
and assumes no responsibility therefor.
20
ADMA020
kawneer.com
© Kawneer Company, Inc., 2014
Kawneer reserves the right to change configuration without prior notice when deemed
necessary for product improvement.
NOTE:
*IR 501 door frame uses IR 500 door jamb with IR 501 filler.