88015

REVISIONS
LTR
A
B
C
D
DESCRIPTION
DATE
APPROVED
Changes in accordance with NOR
5905-R008-92.
Correct vendor CAGE. Editorial changes
throughout.
Change vendor plant address. Editor changes
throughout.
Add pure tin, manufacturer eligibility, and high
power pulse paragraphs. Editorial changes
throughout.
28 May 93
D. Moore
5 Jan 99
A. Ernst
4 Feb 04
K. Cottongim
7 Jan 11
M. Radecki
CURRENT DESIGN ACTIVITY CAGE CODE 037Z3
HAS CHANGED NAMES TO:
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
Prepared in accordance with AMSE Y14.100
Source control drawing
REV STATUS
OF PAGES
REV
D
D
D
D
D
D
D
D
PAGES
1
2
3
4
5
6
7
8
PMIC N/A
PREPARED BY
Allan R. Knox
DESIGN ACTIVITY:
DEFENSE ELECTRONIC SUPPLY CENTER
DAYTON, OH 45444-5000
CHECKED BY
David E Moore
TITLE
RESISTOR NETWORK, 8-PIN, SINGLE INLINE
(SIP) PACKAGE
Original date of
drawing
13 June 88
APPROVED BY
David E. Moore
SIZE
A
REV
AMSC N/A
CODE IDENT. NO.
14933
DWG NO.
D
PAGE
88015
1
OF
8
5905-E747
1. SCOPE
1.1 Scope. This drawing describes the requirements for an eight-pin, single inline package (SIP), resistor network.
1.2 Part or Identifying Number (PIN). The complete PIN is as follows:
88015


Drawing number
-
XX


Schematic number
(see 3.3.1)
2. APPLICABLE DOCUMENTS
2.1 Government documents.
2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of
this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in
the solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATION
MIL-PRF-83401
-
Resistor Networks, Fixed, Film, And Capacitor-Resistor Networks, Ceramic
Capacitor and Fixed Film Resistors, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-1285
-
Marking of Electrical and Electronic Parts.
*
(Copies of these documents are available online at https://assist.daps.dla.mil/quicksearch/ or from the Standardization
Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
*
2.2 Order of precedence. Unless otherwise noted herein or in the event of a conflict between the text of this document
and the references cited herein (except for related specification sheets), the text of this document takes precedence.
Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been
obtained.
3. REQUIREMENTS
3.1 Requirements. Requirements shall be in accordance with MIL-PRF-83401, and as specified herein.
3.2 Interface and physical dimensions. The resistor shall meet the interface and physical dimensions as specified
herein (see figure 1).
3.3 Electrical characteristics.
3.3.1 Resistance. The resistance values shall be as specified on figure 2.
3.3.2 Resistance tolerance. Resistors are available in tolerances specified in figure 2.
3.3.3 Schematic. Resistors are available in schematics listed in figure 2.
DEFENSE ELECTRONIC SUPPLY CENTER
SIZE
CODE IDENT NO.
DWG NO.
DAYTON, OHIO
A
14933
88015
REV D
PAGE
2
.012 + .004
Inches
.004
.005
.006
.009
.010
mm
0.101
0.127
0.152
0.228
0.254
Inches
.012
.015
.017
.019
mm
0.304
0.381
0.431
0.482
Inches
.030
.040
.049
.050
.098
mm
0.762
1.016
1.244
1.270
2.489
Inches
.100
.135
.187
.783
mm
2.540
3.429
4.749
19.888
NOTES:
1. Dimensions are in inches.
2. Metric equivalents are given for general information only.
3. Unless otherwise specified, tolerances are ± .005 (0.13mm).
4. The picturization of the styles above is representative of the envelope of the item. Slight deviations from the outline
shown, which are contained within the envelope and do not alter the functional aspects of the device, are acceptable.
5. Terminal centerline to centerline measurements are made at the point of emergence of the lead from the body.
6. Measurement is made at the point of emergence of the lead from the body.
7. Pin 1 locator shall be a bevel, numeral 1 vertical bar, or a dot adjacent to pin 1 in the shaded area.
8. If the standoffs are located on the body, a minimum of two standoffs are required as illustrated. As an option, additional
standoffs may be located on the body of the resistor network. If leads with standoffs are used, standoffs on the body are not
required.
FIGURE 1. Resistor network.
DEFENSE ELECTRONIC SUPPLY CENTER
SIZE
CODE IDENT NO.
DWG NO.
DAYTON, OHIO
A
14933
88015
REV D
PAGE
3
o
3.3.4 Power ratings. Unless otherwise specified, the individual resistor power rating shall be 100 milliwatts at 70 C
(see figure 2).
o
3.3.5 Package power ratings. The package power rating for resistor networks shall be 0.60 watts at 70 C.
3.3.6 Operating voltage. The maximum operating voltage shall be 50 Volts dc (see table I).
o
o
3.3.7 Temperature range. The operating temperature range shall be from - 55 C to + 125 C. For operation in
o
temperatures in excess of 70 C derated in accordance with figure 3.
o
3.3.8 Resistance temperature characteristic. The resistance temperature characteristic shall not exceed 100 ppm/ C
for characteristic K.
*
3.4 Pure tin. The use of pure tin, as an underplate or final finish is prohibited both internally and externally. Tin content
of resistor components and solder shall not exceed 97 percent, by mass. Tin shall be alloyed with a minimum of 3
percent lead, by mass (see 6.4).
3.5 Marking. Markings shall be in accordance with MIL-STD-1285, except the part number shall be as specified in 1.2,
with the Manufacturer's Commercial and Government Entity (CAGE) code, date and lot codes.
3.6 Recycled, recovered, or environmentally preferable materials. Recycled, recovered, or environmentally preferable
materials should be used to the maximum extent possible provided that the material meets or exceeds the operational
and maintenance requirements, and promotes economically advantageous life cycle costs.
*
3.7 Manufacturer eligibility. To be eligible for listing as an approved source of supply, a manufacturer shall be listed on
the MIL-PRF-83401 Qualified Products List for at least one part, or perform the group A and group B inspections specified
herein on a sample agreed upon by the manufacturer and DLA Land and Maritime-VAT.
*
3.7.1 Certificate of compliance. A certificate of compliance shall be required from manufacturers requesting to be an
approved source of supply.
3.8 Workmanship. Resistors shall be processed in such a manner as to be uniform in quality and parts shall be free
from any defects that will affect life, serviceability, or appearance.
4. VERIFICATION
4.1 Qualification inspection. Qualification inspection is not applicable to this document.
4.2 Conformance inspection.
4.2.1 Inspection of product for delivery. Inspection of product for delivery shall consist of the group A and group B
inspection of MIL-PRF-83401.
4.2.2 Certification. The procuring activity may accept a certificate of compliance in lieu of group B inspection (6.2d).
5. PACKAGING
5.1 Packaging. For acquisition purposes, the packaging requirements shall be as specified in the contract or order (see
6.2). When packaging of materiel is to be performed by DoD or in-house contractor personnel, these personnel need to
contact the responsible packaging activity to ascertain packaging requirements. Packaging requirements are maintained
by the Inventory Control Point's packaging activity within the Military Department or Defense Agency, or within the military
service’s system commands. Packaging data retrieval is available from the managing Military Department's or Defense
Agency's automated packaging files, CD-ROM products, or by contacting the responsible packaging activity.
DEFENSE ELECTRONIC SUPPLY CENTER
SIZE
CODE IDENT NO.
DWG NO.
DAYTON, OHIO
A
14933
88015
REV D
PAGE
4
Schematic 01
NOTE: Resistance tolerance for R1, R2, R3, R4, and R5 shall be ± 2 percent. Resistance tolerance for R6 shall be
± 5 percent.
Schematic 02
NOTE: Resistance tolerance for R1, R2, R3, R4, and R5 shall be ± 2 percent. Resistance tolerance for R6 shall be
± 5 percent.
Schematic 03
NOTE: Resistance tolerance shall be ± 1 percent.
Schematic 04
NOTE: Resistance tolerance shall be ± 1 percent.
FIGURE 2. Schematic and resistance values.
DEFENSE ELECTRONIC SUPPLY CENTER
SIZE
CODE IDENT NO.
DWG NO.
DAYTON, OHIO
A
14933
88015
REV D
PAGE
5
Schematic 05
NOTE: Resistance tolerance shall be ± 1 percent.
Schematic 06
NOTE: Resistance tolerance shall be ± 1 percent.
Schematic 07
NOTES:
1. Resistance tolerance shall be ± 2 percent.
2. Power rating for R1, R2, R5, and R6 shall be 180 mW. Power rating for R3 and R4 shall be 100 mW.
FIGURE 2. Schematic and resistance values - Continued.
DEFENSE ELECTRONIC SUPPLY CENTER
SIZE
CODE IDENT NO.
DWG NO.
DAYTON, OHIO
A
14933
88015
REV D
PAGE
6
TABLE I. Power conditioning pin/voltage connections.
Dash
Number
88015-01
88015-02
88015-03
88015-04
88015-05
88015-06
88015-07
Pin 1
39.0
29.7
31.6
31.6
31.6
18.7
G
Pin 2
G
G
G
G
G
G
50.0
Pin 3
3.0
3.0
27.4
29.8
9.0
15.8
50.0
Voltage 1/ 2/
Pin 4
Pin 5
G
39.0
G
39.0
G
22.6
G
22.6
G
27.0
G
6.8
G
G
Pin 6
10.5
10.5
G
G
G
G
50.0
Pin 7
G
G
22.0
22.0
16.0
17.0
50.0
Pin 8
9.0
9.0
G
G
G
G
G
1/ Values in volts dc.
2/ G = ground.
FIGURE 3. Derating curve.
6. NOTES
(This section contains information of a general or explanatory nature which may be helpful, but is not mandatory.)
6.1 Intended use. Resistors conforming to this drawing are intended for use when military specifications do not exist
and qualified military devices that will perform the required function are not available for the original equipment
manufacturer application.
6.2 Ordering data. The contract or purchase order should specify the following:
a. Complete PIN (see 1.2).
b. Requirements for delivery: One copy of the conformance inspection data or a certificate of compliance that parts
have passed conformance inspection with each shipment of parts by the manufacturer.
c.
Requirements for packaging and packing.
d. Whether the manufacturer performs the group B inspection or provides a certificate of compliance (see 4.2.2).
DEFENSE ELECTRONIC SUPPLY CENTER
SIZE
CODE IDENT NO.
DWG NO.
DAYTON, OHIO
A
14933
88015
REV D
PAGE
7
6.3 Electrostatic charge. Under several combinations of conditions, these resistors can be electrically damaged, by
electrostatic charges, and drift from specified value. Users should consider this phenomena when ordering or shipping
resistors. Direct shipment to the Government is controlled by MIL-DTL-39032 that specifies a preventive packaging
procedure.
*
6.4 Tin whisker growth. The use of alloys with tin content greater than 97 percent, by mass, may exhibit tin whisker
growth problems after manufacture. Tin whiskers may occur anytime from a day to years after manufacture and can
develop under typical operating conditions, on products that use such materials. Conformal coatings applied over top of a
whisker-prone surface will not prevent the formation of tin whiskers. Alloys of 3 percent lead, by mass, have shown to
inhibit the growth of tin whiskers. For additional information on this matter, refer to ASTM-B545 (Standard Specification
for Electrodeposited Coatings of Tin).
*
6.5 Pulse applications. Designers are CAUTIONED on using the above resistors in high power pulse applications. Since
they have not been qualified nor tested for such applications, damage and premature failure are possible.
*
6.6 User of record. Coordination of this document for future revisions is coordinated only with the approved source of
supply and the users of record of this document. Requests to be added as a recorded user of this drawing may be
achieved online at [email protected] or in writing to: DLA Land and Maritime-VAT, Post Office Box 3990, Columbus, OH
43218-3990 or by telephone (614) 692-0552 or DSN 850-0552.
*
6.7 Approved source of supply. Approved source of supply is listed herein. Additional sources will be added as they
become available. Assistance in the use of this drawing may be obtained online at [email protected] or contact
DLA Land and Maritime-VAT, Post Office Box 3990, Columbus, OH 43218-3990 or by telephone (614) 692-0552 or DSN
850-0552.
DLA Land and Maritime
drawing PIN
88015
Vendor similar
designation or
type number 1/
Vendor
CAGE
-01 through -07
8L series
17826
-01 through -07
MSP08A-00-SXX
91637
Vendor name
and address
Vishay - Techno Division
7803 Lemona Avenue
Van Nuys, CA 91405-1139
Vishay Dale Electronics, Incorporated
PO Box 609
Columbus, NE 68602-0609
PLANT:
Electrónica Vishay Dale de México, S.A. de CV.
C. Joule No. 1920
Parque Industrial A.J. Bermúdez
C.P. 32470
CD. Juárez Chihuahua, México
1/ Parts must be purchased to the DLA Land and Maritime PIN to assure that all performance
requirements and tests are met.
DEFENSE ELECTRONIC SUPPLY CENTER
SIZE
CODE IDENT NO.
DWG NO.
DAYTON, OHIO
A
14933
88015
REV D
PAGE
8