PPMxx-X-xxZLF PPM-SERIES Rev.09-2013 5 - 20 Watt Univ. 85-264VAC and 50/60Hz Dual Output Overload Protection 3 kV AC I/O Isolation Low Ripple and Noise High Efficiency Mainzer Straße 151–153 D-55299 Nackenheim Tel. +49 6135 7026-0 Fax: +49 6135 931070 www.peak-electronics.de [email protected] The PPM-Series are high efficiency green power moduls with various packaging provided by Peak. The features of this series are: wide input voltage, DC and AC all in one, high efficiency, high reliability, low loss, safety isolation etc. They are widely used in industrial, office and civil equipments. EMC and safety standards meet international standards IEC61000 UL60950 and IEC60950, and Multi-certificate is in processing. All specifications typical at Ta=25°C, nominal input voltage and full load unless otherwise specified Input Specifications Input Voltage Range Input Frequency Input (Inrush) Current 85 – 264 VAC or 120 – 370 VDC universal 47 – 63 Hz 110 VAC 230 VAC 120mA (10A), typ. 70mA (20A), typ. 230mA (10A), typ. 120mA (20A), typ. 250mA (10A), typ. 140mA (20A), typ. 280mA (16A), typ. 160mA (30A), typ. 330mA (16A), typ. 180mA (30A), typ. PPM05 models PPM10 models PPM15 models (5/12/15V) PPM15 model (24V) PPM20 models External Input Fuse (recommended) PPM05 models 1A / 250V slow blow PPM10 / 15 models 2A / 250V slow blow PPM20 models 3.15A / 250V slow blow Output Specifications Voltage Accuracy Line Regulation ±2% (main output) ±0.5% (main output) ±1.5% (supplement output) ±2% (Balanced load) 10% ≤ 100mV pk-pk (main output) Continuous, auto recovery ≥ 110% Io Load Regulation (10-100%) Minimum load Ripple and Noise (20Mhz bandwidth) Short Circuit Protection Over Current Protection Over output voltage protection 5VDC models ≤7.5VDC 12 / 15VDC models ≤20VDC 24VDC models ≤30VDC PPM-Series – PPMxx-X-xxZLF – Dual Output - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 1/5 PPMxx-X-xxZLF Common Specifications Temperature range Power derating Case temperature Storage Hold up Time Humidity (non condensing) Temperature Coefficient -40°C to +70 °C 3.75% / °C (above 55°C) +90°C (max) -40°C to +105 °C 80mS, typ. (230VAC) 95%, max. 0.02%/°C (main output) 0.15%/°C (supplement output) 150kHz, max. 3000VAC / 1min. 0.3mA RMS typ. (230VAC / 50Hz) EN55022, level B Switching Frequency I/O Isolation Voltage Leakage current EMI / RFI conducted EMC compliance ESD RF EFT / bursts Surge Safety Standards Safety Approvals* Safety Class Case Material Reliability Calculated MTBF (MIL-HDBK-217F) Weight IEC/EN 61000-4-2 level 3 6KV/8KV IEC/EN 61000-4-3 IEC/EN 61000-4-4 level 3 2KV IEC/EN 61000-4-5 level 3 1KV / 2KV IEC60950, EN60950, UL60950 EN60950, IEC60950, UL60950 CLASS 1 UL94V-0 rated > 300,000 hrs 50g (PPM05) 70g (PPM10) 80g (PPM15) 120g (PPM20) *pending for PPM15-C-24ZLF Notes: PPM-Series – PPMxx-X-xxZLF – Dual Output - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 2/5 Selection Guide Dual Output Order # P r (W owe ) tage Vol t u p Out ) mA ad ( o L ll t Fu re n r (% ) u ncy tC e u i p c t i f Ou Ef c) (Vd DUAL OUTPUT PPM05-A-05ZLF PPM05-A-12ZLF PPM05-A-15ZLF PPM05-A-24ZLF 5 5 5 5 ±5 ± 12 ± 15 ± 24 ± 500 ± 210 ± 160 ± 100 75 79 79 80 PPM10-B-05ZLF PPM10-B-12ZLF PPM10-B-15ZLF PPM10-B-24ZLF 10 10 10 10 ±5 ± 12 ± 15 ± 24 ± 1000 ± 450 ± 350 ± 200 76 80 81 84 PPM15-C-05ZLF PPM15-C-12ZLF PPM15-C-15ZLF PPM15-C-24ZLF 15 15 15 15 ±5 ± 12 ± 15 ± 24 ± 1500 ± 650 ± 500 ± 310 76 81 83 80 PPM20-D-05ZLF PPM20-D-12ZLF PPM20-D-15ZLF 20 20 20 ±5 ± 12 ± 15 ± 2000 ± 830 ± 650 75 82 83 If you need other specifications, please enquire. Notes: PPM-Series – PPMxx-X-xxZLF – Dual Output - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 3/5 Package / Pinning / Derating PIN CONNECTIONS # DUAL 1 Ground 2 AC (N) 3 AC (L) 4 - Vout 5 No Pin 6 Common 7 No Pin 8 +Vout TRIM No Pin No. PPM05-A A 12.5 B 48.5 C 40.5 D 4.0 E 16.0 F 36.0 G 20.5 H min. 6.0 No. A B C D E F G H PPM10-B 17.5 55.0 47.0 5.0 20.0 45.0 20.5 min. 6.0 No. PPM15-C A 17.5 B 62.0 C 54.0 D 5.0 E 20.0 F 48.0 G 22.5 H min. 6.0 No. A B C D E F G H PPM20-D 20.0 70.0 62.0 5.75 23.0 48.0 23.5 min. 6.0 Load % 100 80 60 40 -40 -10 55 Temperature PPM-Series – PPMxx-X-xxZLF – Dual Output - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 4/5 70 App Notes: Typical Application Fuse NT C L L +Vo N N Co m -Vo EXTERNAL CAPACITORS TYPICAL VALUE (µ µF) MODEL PPM05-A-05ZLF PPM05-A-12ZLF PPM05-A-15ZLF PPM05-A-24ZLF PPM10-B-05ZLF PPM10-B-12ZLF PPM10-B-15ZLF PPM10-B-24ZLF PPM15-C-05ZLF PPM15-C-12ZLF PPM15-C-15ZLF PPM20-D-05ZLF PPM20-D-12ZLF PPM20-D-15ZLF C1 C 2 TVS1 RL C3 C 4 TVS2 R L Remark: 1. Output filtering capacitors C1, C2 and C3 are electrolytic capacitors, It is recommended to use high frequency and low impedance electrolytic capacitors. For capacitance and current of capacitor please refer to manufacture’s datasheet. Voltage derating of capacitor should be 80% or above. C2, C4, C6 are used to filter high frequency noise. TVS is a recommended component to protect post-circuits (if converter fails). 2. External input NTC is recommended to use 5D-9 ( Only PPM10 models and PPM15 models) C1 120 68 47 10 220 120 47 33 470 220 120 470 120 68 Parallel Lines Measure Copper sheet Fuse C1 C2 Load Connect Oscillograph Probe 2 25.4m m 25.4m m Notes: PPM-Series – PPMxx-X-xxZLF – Dual Output - Plastic Case Specification can change without a notice – We accept no liability for any inaccuracy or printing errors. Page 5/5 C3 120 68 47 10 220 120 47 33 470 220 120 470 120 68