P6LG_K

P6LG-xxxxEK
Mainzer Straße 151–153
D-55299 Nackenheim
Tel. +49 6135 7026-0
Fax: +49 6135 931070
www.peak-electronics.de
[email protected]
PMM4-SERIES
Rev.04-2015
1 Watt
Regulated
Short Circuit Protection
Single Output
SIP7 Case
3 kV DC I/O Isolation
Low Ripple and Noise
The PMM4 series is a family of cost effective 1 W regulated single output
DC/DC converters with short circuit protection. These converters are in an
ultra miniature SIP7 case. Devices are encapsulated. High performance
features: Regulated Output, 3000VDC input/output isolation, high efficiency
operation, output voltage accuracy of ±2% maximum, input range of ±10%
tolerance and low output ripple and noise.
All specifications typical at Ta=25°C, nominal input voltage and full load unless otherwise specified
Input Specifications
Voltage Range
Input Filter
Input Reflected Ripple Current¹
± 10%
Capacitors
20 mA pk-pk
Output Specifications
Voltage Accuracy
Short Circuit Protection
Line Regulation
Load Regulation (0% - 100%)
Ripple and Noise (20Mhz bandwidth)
Temperature Coefficient
± 2%
Continuous
± 0.5%
± 0.5% (3.3Vout Models: ± 1.0%)
50 mV pk-pk
± 0.02% / °C
General Specifications
Efficiency
I/O Isolation Voltage (3 sec.)
I/O Isolation Capacity
I/O Isolation Resistance
Switching Frequency
Humidity
Reliability Calculated MTBF (MIL-HDBK-217F)
See Table
3000 VDC
60 pF, typ.
1000 M Ohm
50 kHz (Variable)
95% rel H
> 3.5 Mhrs
Physical Specifications
Case Material
Potting Material
Weight
Non Conductive Black Plastic (UL94V-0 rated)
Epoxy (UL94V-0 rated)
~ 2.7g, typ.
Environment Specifications
Operating Temperature
Maximum Case Temperature
Storage Temperature
Cooling
RoHS Conform
-40 to +85°C (ambient)
100°C
-40 to +125°C
Free Air Convection (10 mm distance required)
Soldering 260°C, max. (1.5 mm from case 10s.)
PMM4-Series – P6LG-xxxxEK – Single Output – SIP7 - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 1/3
Selection Guide
Single Output
A)
)
)
d (m
(mA a d (mA
a
)
d
o
a
L
C
o
)
)²
ll
(u F
(V D
o Lo t Fu ll L
V DC
t Fu
d
(
e
N
)
n
a
g
t
e
e
o
n
a
n
r
t
r re
y (% citor L
r re
ltag
Vo l
C ur
ie nc
t Cu p ut Cu
t Vo
a
pu t
pu t
In
O ut
E ffic
Out
Inp u
Inp u
Ca p
Order #
SINGLE OUTPUT
P6LG-053R3EK
P6LG-0505EK
P6LG-057R2EK
P6LG-0509EK
P6LG-0512EK
P6LG-0515EK
P6LG-123R3EK
P6LG-1205EK
P6LG-127R2EK
P6LG-1209EK
P6LG-1212EK
P6LG-1215EK
P6LG-243R3EK
P6LG-2405EK
P6LG-247R2EK
P6LG-2409EK
P6LG-2412EK
P6LG-2415EK
5
5
5
5
5
5
12
12
12
12
12
12
24
24
24
24
24
24
30
30
30
35
35
35
20
20
20
20
20
20
10
10
10
10
10
10
363
312
312
307
303
303
148
130
128
126
126
122
74
66
64
63
62
62
3.3
5
7.2
9
12
15
3.3
5
7.2
9
12
15
3.3
5
7.2
9
12
15
333
200
138.9
111.1
83.3
66.7
333
200
138.9
111.1
83.3
66.7
333
200
138.9
111.1
83.3
66.7
55
64
64
65
66
66
56
64
65
66
66
68
56
63
65
66
67
67
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
220
If you need other specifications, please enquire.
Notes:
PMM4-Series – P6LG-xxxxEK – Single Output – SIP7 - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 2/3
0.50
(0.02)
3.00
(0.12)
10.00
(0.39)
2.00
(0.08)
0.25
(0.01)
Package / Pinning / Derating
PIN CONNECTIONS
#
SINGLE (3KV)
1 +Vin
2 - Vin
4 Omitted
5 - Vout
6 Omitted
7 +Vout
App Notes:
¹ = Measured Input reflected ripple current with a simulated source inductance of 12uH.
² = Tested by minimal Vin and constant resistive load.
EMV Specifications
Conducted Disturbance
Radiated Emission
ESD
RS
EFT
Surge
CS
PFMF
EN55022, CLASS B
EN55022, CLASS B
IEC61000-4-2 Perf. Criteria A
IEC61000-4-3 Perf. Criteria A
IEC61000-4-4 Perf. Criteria A
IEC61000-4-5 Perf. Criteria A
IEC61000-4-6 Perf. Criteria A
IEC61000-4-8 Perf. Criteria A
EMI Filter:
Input Filter Components help to
meet conducted emissions
requirement.
C1: 470uF/100V
L: 12uH
PMM4-Series – P6LG-xxxxEK – Single Output – SIP7 - Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 3/3