P(C)6NG_2:1

P(C)6NG-xxxxE/Z2:1(H30)(M)LF
PMB-SERIES
Rev.05-2011
1 Watt
2:1 Wide Input
Reg. Single and Dual Output
1 - 3 kV DC I/O Isolation
SIP8 Plastic or Metal* case
On/Off Control (optional)
Contin. Short Circuit Protection
Mainzer Straße 151–153
D-55299 Nackenheim
Tel. +49 6135 7026-0
Fax: +49 6135 931070
www.peak-electronics.de
[email protected]
The PMB 1 Watt series is a family of cost effective 1 W single and dual
output DC/DC converters with an optional control Pin. These converters are
encapsulated in an ultra miniature SIP8 or DIP16 plastic or metal case.
High performance features: continuous / long time short circuit protection
with automatic restart and tight line / load regulation, high efficiency
operation and output voltage accuracy of ±2% maximum.
All specifications typical at Ta=25°C, nominal input voltage and full load unless otherwise specified
Input Specifications
Voltage Range
Input Filter
Input Reflected Ripple Current¹
2:1 Wide Input (see table)
Capacitor
35 mA pk-pk
Output Specifications
Voltage Accuracy
Short Circuit Protection
Line Regulation
Load Regulation (25% - 100%)
Cross Regulation (for dual output only)
Ripple and Noise (20Mhz bandwidth)
Temperature Coefficient
± 2%
Indefinite (Automatic Recovery)
± 0.5%, max.
± 1%, max.
± 5%
80 mV pk-pk, max.
± 0.02% / °C
General Specifications
I/O Isolation Voltage (3 sec.)
I/O Isolation Capacity
I/O Isolation Resistance
Switching Frequency
Humidity
Reliability Calculated MTBF (MIL-HDBK-217F)
Safety Standard (designed to meet)
1000 VDC (3000 VDC optional)*
60 pF, max
1000 M Ohm, min.
100 - 650 kHz
95% rel H
> 1.66 Mhrs
IEC/EN 60950-1
Physical Specifications
Case Material
Potting Material
Weight
Non Conductive Black Plastic (UL94V-0 rated)
Nickel Coated Copper* (optional)
Epoxy (UL94V-0 rated)
~ 4.5g, typ. (~ 6.5g, for Metal Case)
Environment Specifications
Operating Temperature
Maximum Case Temperature
Storage Temperature
Cooling
RoHS Conform
-40 to +85°C (ambient)
100°C
-40 to +125°C
Free Air Convection (10mm distance required)
Soldering 260°C, max. (1.5mm from case 10s.)
PMB-Series – P(C)6NG-xxxxE/Z2:1(H30)(M)LF – Single / Dual Output – SIP8 – Metal / Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 1/4
Selection Guide
Single Output
A)
)
mA)
d (m
mA) ad (mA
(
a
ad (
o
)
d
o
L
a
L
C
)
o
.
l
o
l
L
C
in
L
u
uF)²
ll
VD
(VD
nt F
nt M
)
ad (
t No rent Fu
ge (
e
e
e
o
a
n
r
r
%
g
t
r
r
(
L
l
e
a
r
u
u
r
r
y
lt
or
C
Vo
C
ienc
t Cu put Cu
t Vo
acit
put
put
pu t
In p u
Inpu
In
O ut
O ut
O ut
Effic
C ap
Order #
SINGLE OUTPUT
P6NG-053R3E2:1LF
P6NG-0505E2:1LF
P6NG-0509E2:1LF
P6NG-0512E2:1LF
P6NG-0515E2:1LF
P6NG-0524E2:1LF
P6NG-123R3E2:1LF
P6NG-1205E2:1LF
P6NG-1209E2:1LF
P6NG-1212E2:1LF
P6NG-1215E2:1LF
P6NG-1224E2:1LF
P6NG-243R3E2:1LF
P6NG-2405E2:1LF
P6NG-2409E2:1LF
P6NG-2412E2:1LF
P6NG-2415E2:1LF
P6NG-2424E2:1LF
P6NG-483R3E2:1LF
P6NG-4805E2:1LF
P6NG-4809E2:1LF
P6NG-4812E2:1LF
P6NG-4815E2:1LF
P6NG-4824E2:1LF
4.5-9
4.5-9
4.5-9
4.5-9
4.5-9
4.5-9
9-18
9-18
9-18
9-18
9-18
9-18
18-36
18-36
18-36
18-36
18-36
18-36
36-72
36-72
36-72
36-72
36-72
36-72
15
15
40
55
55
70
15
15
15
15
15
15
8
8
8
8
8
8
6
6
6
6
6
6
298
298
285
285
285
294
119
115
108
108
108
114
59
57
55
55
55
55
31
30
29
29
29
30
3.3
5
9
12
15
24
3.3
5
9
12
15
24
3.3
5
9
12
15
24
3.3
5
9
12
15
24
76
50
28
21
17
10
76
50
28
21
17
10
76
50
28
21
17
10
76
50
28
21
17
10
303
200
111
83
67
42
303
200
111
83
67
42
303
200
111
83
67
42
303
200
111
83
67
42
67
67
70
70
70
68
70
72
77
77
77
73
70
72
75
75
75
75
66
68
70
70
70
68
3300
3300
470
470
470
220
3300
3300
470
470
470
220
3300
3300
470
470
470
220
3300
3300
470
470
470
220
If you need other specifications, please enquire.
*OPTIONS:
Control On/Off
3 kV I/O Isolation
Metal Case
For Optional control Pin please add “C”
between P and 6
(for example: PC6NG-2424E2:1LF)
For optional 3kV DC I/O Isolation, please
add “H30” before LF!
(P6NG-2424E2:1H30LF for 3kV)
For optional Metal Case, please add “M”
before LF!
(P6NG-2424Z2:1MLF for Metal Case)
PMB-Series – P(C)6NG-xxxxE/Z2:1(H30)(M)LF – Single / Dual Output – SIP8 – Metal / Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 2/4
Selection Guide
Dual Output
)
)
mA)
mA)
(mA ad (mA
ad (
ad (
o
)
o
d
L
L
a
C
o
.
L
D
F)²
in
Lo
ull
d (u
(V
No
e (V
F u ll
nt F
nt M
)
a
t
t
g
e
e
e
o
n
n
a
r
r
%
g
t
r
L
(
r
l
e
e
rr
y
rr
lta
or
Cu
Vo
Cu
t Vo
t Cu put Cu
ie n c
acit
put
put
put
In p u
In p u
In
O ut
Out
O ut
Effic
Cap
DC)
Order #
DUAL OUTPUT
P6NG-053R3Z2:1LF
P6NG-0505Z2:1LF
P6NG-0509Z2:1LF
P6NG-0512Z2:1LF
P6NG-0515Z2:1LF
P6NG-0524Z2:1LF
P6NG-123R3Z2:1LF
P6NG-1205Z2:1LF
P6NG-1209Z2:1LF
P6NG-1212Z2:1LF
P6NG-1215Z2:1LF
P6NG-1224Z2:1LF
P6NG-243R3Z2:1LF
P6NG-2405Z2:1LF
P6NG-2409Z2:1LF
P6NG-2412Z2:1LF
P6NG-2415Z2:1LF
P6NG-2424Z2:1LF
P6NG-483R3Z2:1LF
P6NG-4805Z2:1LF
P6NG-4809Z2:1LF
P6NG-4812Z2:1LF
P6NG-4815Z2:1LF
P6NG-4824Z2:1LF
4.5-9
4.5-9
4.5-9
4.5-9
4.5-9
4.5-9
9-18
9-18
9-18
9-18
9-18
9-18
18-36
18-36
18-36
18-36
18-36
18-36
36-72
36-72
36-72
36-72
36-72
36-72
15
15
20
20
40
70
15
15
15
15
15
40
8
8
8
8
8
20
6
6
6
6
6
12
285
270
270
266
285
298
119
115
109
109
112
124
59
59
54
54
55
59
30
30
28
27
29
30
± 3.3
± 5.0
± 9.0
± 12.0
± 15.0
± 24.0
± 3.3
± 5.0
± 9.0
± 12.0
± 15.0
± 24.0
± 3.3
± 5.0
± 9.0
± 12.0
± 15.0
± 24.0
± 3.3
± 5.0
± 9.0
± 12.0
± 15.0
± 24.0
± 38
± 25
± 14
± 10
±8
±5
± 38
± 25
± 14
± 10
±8
±5
± 38
± 25
± 14
± 10
±8
±5
± 38
± 25
± 14
± 10
±8
±5
± 152
± 100
± 56
± 42
± 33
± 21
± 152
± 100
± 56
± 42
± 33
± 21
± 152
± 100
± 56
± 42
± 33
± 21
± 152
± 100
± 56
± 42
± 33
± 21
70
74
74
75
70
67
70
72
76
76
74
67
70
70
76
77
75
70
70
70
74
76
72
70
± 1000
± 1000
± 220
± 220
± 220
± 100
± 1000
± 1000
± 220
± 220
± 220
± 100
± 1000
± 1000
± 220
± 220
± 220
± 100
± 1000
± 1000
± 220
± 220
± 220
± 100
If you need other specifications, please enquire.
*OPTIONS:
Control On/Off
3 kV I/O Isolation
Metal Case
For Optional control Pin please add “C”
between P and 6
(for example: PC6NG-2424Z2:1LF)
For optional 3kV DC I/O Isolation, please
add “H30” before (M)LF!
(P6NG-2424Z2:1H30LF for 3kV)
For optional Metal Case, please add “M”
before LF!
(P6NG-2424Z2:1MLF for Metal Case)
PMB-Series – P(C)6NG-xxxxE/Z2:1(H30)(M)LF – Single / Dual Output – SIP8 – Metal / Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 3/4
10.60
(0.42)
3.05
(0.12)
0.50
(0.02)
3.05
(0.12)
0.50
(0.02)
10.60
(0.42)
3.50
(0.14)
3.50
(0.14)
0.25
(0.01)
0.25
(0.01)
Package / Pinning / Derating
FOR METAL CASE PLEASE ADD „M“ BEFORE „LF“
E.G.: PC6NG-0505EH30MLF
#
1
2
3
5
6
7
8
SINGLE
- Vin
+Vin
Omitted
Omitted
+Vout
- Vout
N.C.
PIN CONNECTIONS
DUAL SINGLE "C"
- Vin
- Vin
+Vin
+Vin
N.C.
Ctrl.
N.C.
N.C.
+Vout
+Vout
- Vout
- Vout
Common N.C.
DUAL "C"
- Vin
+Vin
Ctrl.
N.C.
+Vout
- Vout
Common
(Same pinning for 3kv I/O isolation)
App Notes:
¹ = Measured Input reflected ripple current with a simulated source inductance of 12uH
² = Tested by nominal Vin and constant resistive load.
- Operation under no-load conditions will not damage these devices, but they will not observe the listed specifications.
Remote ON/OFF Control (Only for optional Ctrl Verion -> PC6NG…)
MCU (Master Control Unit)
The MCU Pin Voltage is referenced to –Vin (Pin1)
ON:
0 – 0.8 VDC / open or short circuit Pin1 and Pin3
OFF:
4.5 to 15 VDC, max.
OFF idle current: 3.5mA to 15mA, max. (5mA, typ.)
PMB-Series – P(C)6NG-xxxxE/Z2:1(H30)(M)LF – Single / Dual Output – SIP8 – Metal / Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 4/4