P(C)14NG_2:1

P(C)14NG-xxxxE/Z2:1(M)LF
PMB-SERIES
Rev.02-2011
3 Watt
2:1 Wide Input
Reg. Single and Dual Output
1.6 kV DC I/O Isolation
SIP8 Plastic or Metal* case
On/Off Control (optional)
Contin. Short Circuit Protection
Mainzer Straße 151–153
D-55299 Nackenheim
Tel. +49 6135 7026-0
Fax: +49 6135 931070
www.peak-electronics.de
[email protected]
The PMB series is a family of cost effective 1, 2 and 3 W single and dual
output DC/DC converters with an optional control Pin. These converters are
in an ultra miniature SIP8 or DIP16 plastic or metal case. Devices are
encapsulated using flame retardant resin. High performance features
include continuous / long time short circuit protection with automatic restart
and tight line / load regulation. High performance features include high
efficiency operation and output voltage accuracy of ±1-2% maximum. PMBSeries is a good substitution of traditional DC/DC converters 3W in DIP24
package.
All specifications typical at Ta=25°C, nominal input voltage and full load unless otherwise specified
Input Specifications
Voltage Range
Input Filter
Input Reflected Ripple Current¹
Start Up Time
2:1 Wide Input (see table)
Capacitor
35 mA pk-pk
20ms, typ.
Output Specifications
Voltage Accuracy
Short Circuit Protection
Line Regulation
Load Regulation (25% - 100%)
Cross Regulation (for dual output only)
Ripple and Noise (20Mhz bandwidth)
Temperature Coefficient
Transient Recovery Time / Response Dev.
± 1%
Indefinite (Automatic Recovery)
± 0.5%, max.
± 1%, max.
± 5%
75 mV pk-pk, max.
± 0.02% / °C
300us, typ. / ± 3%, max.
General Specifications
I/O Isolation Voltage (3 sec.)
I/O Isolation Capacity
I/O Isolation Resistance
Switching Frequency
Humidity
Reliability Calculated MTBF (MIL-HDBK-217F)
Safety Standard (designed to meet)
1600 VDC
680 pF, max.
1000 M Ohm, min.
100 - 650 kHz
95% rel H
> 1.34 Mhrs
IEC/EN 60950-1
Physical Specifications
Case Material
Potting Material
Weight
Non Conductive Black Plastic (UL94V-0 rated)
Nickel Coated Copper* (optional)
Epoxy (UL94V-0 rated)
~ 4.8g, typ. (~ 6.5g, for Metal Case)
Environment Specifications
Operating Temperature
Maximum Case Temperature
Storage Temperature
Cooling
RoHS Conform
-40 to +71°C (ambient, for 100% load)
100°C
-40 to +125°C
Free Air Convection (10mm distance required)
Soldering 260°C, max. (1.5mm from case 10s.)
PMB-Series – P(C)14NG-xxxxE/Z2:1(M)LF – Single / Dual Output – SIP8 - Metal / Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 1/3
Selection Guide
Single and Dual Output
A)
A)
)
d (m
m A ) a d (m A
d (m
(
a
a
o
)
d
o
L
³
L
C
)
o
.
oa
(u F )
(VD
Full
Min
VDC nt No L nt Full L
oad
age
%)
rent
re n t
ge (
t
L
(
r
r
l
e
e
a
r
r
u
u
r
o
t
y
r
r
l
o
V
C
C
ienc
t Vo
t Cu put Cu
acit
pu t
put
put
In p u
In p u
In
O ut
Out
O ut
E ffic
C ap
Order #
SINGLE OUTPUT
P14NG-053R3E2:1LF
P14NG-0505E2:1LF
P14NG-0512E2:1LF
P14NG-0515E2:1LF
P14NG-123R3E2:1LF
P14NG-1205E2:1LF
P14NG-1212E2:1LF
P14NG-1215E2:1LF
P14NG-2015E2:1LF
P14NG-243R3E2:1LF
P14NG-2405E2:1LF
P14NG-2412E2:1LF
P14NG-2415E2:1LF
P14NG-483R3E2:1LF
P14NG-4805E2:1LF
P14NG-4812E2:1LF
P14NG-4815E2:1LF
4.5-9
4.5-9
4.5-9
4.5-9
9-18
9-18
9-18
9-18
15 - 30
18-36
18-36
18-36
18-36
36-72
36-72
36-72
36-72
65
70
75
75
25
15
35
35
25
15
15
20
20
10
10
15
15
640
800
750
750
260
320
305
305
180
133
160
156
152
66
82
78
78
3.3
5
12
15
3.3
5
12
15
15
3.3
5
12
15
3.3
5
12
15
175
150
62.5
50
175
150
62.5
50
50
175
150
62.5
50
175
150
62.5
50
700
600
250
200
700
600
250
200
200
700
600
250
200
700
600
250
200
74
76
82
82
76
81
84
84
83
74
79
82
84
75
78
81
81
2200
1000
470
220
2200
1000
470
220
220
2200
1000
470
220
2200
1000
470
220
DUAL OUTPUT
P14NG-0505Z2:1LF
P14NG-0512Z2:1LF
P14NG-0515Z2:1LF
P14NG-1205Z2:1LF
P14NG-1212Z2:1LF
P14NG-1215Z2:1LF
P14NG-2405Z2:1LF
P14NG-2412Z2:1LF
P14NG-2415Z2:1LF
P14NG-4805Z2:1LF
P14NG-4812Z2:1LF
P14NG-4815Z2:1LF
4.5-9
4.5-9
4.5-9
9-18
9-18
9-18
18-36
18-36
18-36
36-72
36-72
36-72
90
90
90
45
45
45
20
20
20
15
20
15
800
760
750
320
308
312
160
154
154
82
80
78
±5
± 12
± 15
±5
± 12
± 15
±5
± 12
± 15
±5
± 12
± 15
± 75
± 31.25
± 25
± 75
± 31.25
± 25
± 75
± 31.25
± 25
± 75
± 31.25
± 25
± 300
± 125
± 100
± 300
± 125
± 100
± 300
± 125
± 100
± 300
± 125
± 100
77
81
82
80
83
82
80
83
83
78
80
81
± 470
± 220
± 100
± 470
± 220
± 100
± 470
± 220
± 100
± 470
± 220
± 100
If you need other specifications, please enquire.
*OPTIONS:
Control On/Off
Metal Case
For Optional control Pin please add “C”
between P and 14
(for example: PC14NG-2424E2:1LF)
For optional Metal Case, please add “M”
before LF!
(P14NG-2424E2:1MLF for Metal Case)
PMB-Series – P(C)14NG-xxxxE/Z2:1(M)LF – Single / Dual Output – SIP8 - Metal / Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 2/3
10.60
(0.42)
0.50
(0.02)
0.50
(0.02)
3.05
(0.12)
3.05
(0.12)
10.60
(0.42)
3.50
(0.14)
3.50
(0.14)
0.25
(0.01)
0.25
(0.01)
Package / Pinning / Derating
FOR METAL CASE PLEASE ADD „M“ BEFORE „LF“
E.G.: PC14NG-0505EMLF
#
1
2
3
5
6
7
8
SINGLE
- Vin
+Vin
Omitted
Omitted
+Vout
- Vout
N.C.
PIN CONNECTIONS
DUAL SINGLE "C"
- Vin
- Vin
+Vin
+Vin
N.C.
Ctrl.
N.C.
N.C.
+Vout
+Vout
Common - Vout
- Vout
N.C.
DUAL "C"
- Vin
+Vin
Ctrl.
N.C.
+Vout
Common
- Vout
(Same pinning for 3kv I/O isolation)
App Notes:
¹ = Measured Input reflected ripple current with a simulated source inductance of 12uH
² = Tested by nominal Vin and constant resistive load.
Remote ON/OFF Control (Only for optional Ctrl Version -> PC14NG…)
ON:
OFF:
Open or high impedance
3mA to 6mA input current (via 1K)
EMI Filter / EMC Specifications
EMC SPECIFICATIONS
Input filter components (C1, L) are used to help meet conducted
emissions requirement for the module. These components
should be mounted as close as possible to the module; and all
leads should be minimized to decrease radiated noise.
5Vin:
C1: 220uF / 25V
L: 5.6uH
12Vin, single: C1: 100uF / 100V
L: 18uH
12Vin, dual:
C1: 1210, 2.2uF / 100V L: 18uH
24Vin:
C1: 1210, 10uF / 35V
L: 18uH
48Vin:
C1: 100uF / 100V
L: 56uH
Radiated
Emissions
Conducted
Emissions
ESD
RS
EFT
Surge
CS
PFMF
EN 55022
CLASS A
EN 55022
CLASS A
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-5
IEC 61000-4-6
IEC 61000-4-8
Perf. Criteria B
Perf. Criteria A
Perf. Criteria B
Perf. Criteria B
Perf. Criteria A
Perf. Criteria A
An external filter capacitor is required if the module has to meet
EN61000-4-4 and EN61000-4-5. (e.g. 220uF/100V)
PMB-Series – P(C)14NG-xxxxE/Z2:1(M)LF – Single / Dual Output – SIP8 - Metal / Plastic Case
Specification can change without a notice – We accept no liability for any inaccuracy or printing errors.
Page 3/3