30-FT123BA040MR-L878L08 target datasheet flow 3xBOOST 2 SiC 1200 V / 40 mΩ Features flow 2 13mm housing ● Three-leg Booster module ● Full SiC for ultra fast switching frequency ● Low inductive package ● Ultra high efficient Schematic Target applications ● Solar Types ● 30-FT123BA040MR-L878L08 Maximum Ratings Tj = 25 °C, unless otherwise specified Parameter Symbol Condition Value Unit 1200 V 31 A 137 A 66 W Boost Switch Drain-source voltage VDSS Drain current ID Tj = Tjmax Peak drain current IDM tp limited by Tjmax Total power dissipation Ptot Tj = Tjmax Gate-source voltage VGSS -4/22 V Maximum Junction Temperature Tjmax 175 °C Copyright Vincotech Ts = 80 °C Ts = 80 °C 1 20 Apr. 2016 / Revision 1 30-FT123BA040MR-L878L08 target datasheet Maximum Ratings Tj = 25 °C, unless otherwise specified Parameter Symbol Condition Value Unit 1200 V Boost Diode Peak Repetitive Reverse Voltage Continuous (direct) forward current VRRM IF Tj = Tjmax Ts = 80 °C 39 A Total power dissipation Ptot Tj = Tjmax Ts = 80 °C 93 W Maximum Junction Temperature Tjmax 175 °C VRRM 1600 V 53 A 490 A 1200 A2s 86 W ByPass Diode Peak Repetitive Reverse Voltage Continuous (direct) forward current Surge (non-repetitive) forward current IF Tj = Tjmax Ts = 80 °C 50 Hz Single Half Sine Wave tp = 10 ms Tj = 150 °C Tj = Tjmax Ts = 80 °C IFSM Surge current capability I2t Total power dissipation Ptot Maximum Junction Temperature Tjmax 150 °C VMAX 1500 V Top -55…+125 °C Storage temperature T stg -40…+125 °C Operation temperature under switching condition T jop -40…(T jmax - 25) °C 4000 V Creepage distance min. 12,7 mm Clearance min. 12,7 mm Capacitor (DC) Maximum DC voltage Operation Temperature Module Properties Thermal Properties Isolation Properties Isolation voltage Comparative Tracking Index Copyright Vincotech V isol DC Test Voltage CTI tp = 2 s > 200 2 20 Apr. 2016 / Revision 1 30-FT123BA040MR-L878L08 target datasheet Characteristic Values Parameter Symbol Conditions VCE [V] VGE [V] VDS [V] VGS [V] VF [V] Value IC [A] ID [A] IF [A] Tj [°C] Min Unit Typ Max 25 39 50 125 52 150 60 Boost Switch Static Drain-source on-state resistance Gate-source threshold voltage 18 rDS(on) VGS(th) 20 VGS = VDS 0,01 Gate to Source Leakage Current IGSS 22 -4 Zero Gate Voltage Drain Current IDSS 0 0 1200 25 2,7 5,6 V 25 100 -100 nA 25 10 µA Internal gate resistance rg 7 Gate charge Qg 107 Gate to source charge QGS Gate to drain charge QGD 41 Short-circuit input capacitance Ciss 1337 Short-circuit output capacitance Coss Reverse transfer capacitance Crss 18 f = 1 MHz 0 600 20 800 mΩ 25 25 Ω 22 nC pF 76 27 Thermal Thermal resistance junction to sink Rth(j-s) phase-change material λ = 3,4 W/mK 1,45 K/W Boost Diode Static Forward voltage Reverse leakage c urrent 30 VF 1200 Ir 25 1,43 125 1,76 150 1,89 25 1,4 V 600 µA Thermal Thermal resistance junc tion to sink Copyright Vincotech R th(j-s) phase-change material λ = 3,4 W /mK 1,02 3 K/W 20 Apr. 2016 / Revision 1 30-FT123BA040MR-L878L08 target datasheet Characteristic Values Parameter Symbol Conditions Value VCE [V] IC [A] VGE [V] VDS [V] ID [A] VGS [V] VF [V] IF [A] Tj [°C] Min Unit Typ Max 1,22 1,48 1,8 ByPass Diode Static Forward voltage VF Reverse leakage current Ir 50 1600 25 125 25 150 50 1100 V µA Thermal Thermal resistance junction to sink Rth(j-s) phase-change material λ = 3,4 W/mK 0,82 K/W 78 nF Capacitor (DC) Capacitance C Tolerance -10 +10 % Thermistor Rated resistance 25 R Deviation of R100 ΔR/R Power dissipation P R100 = 1484 Ω 100 Power dissipation constant 22 -5 kΩ 5 % 25 5 mW 25 1,5 mW/K B-value B(25/50) Tol. ±1% 25 3962 K B-value B(25/100) Tol. ±1% 25 4000 K Vincotech NTC Reference Copyright Vincotech I 4 20 Apr. 2016 / Revision 1 30-FT123BA040MR-L878L08 target datasheet Ordering Code & Marking Version without thermal paste 13mm housing with solder pins Ordering Code 30-FT123BA040MR-L878L08 NN-NNNNNNNNNNNNNN TTTTTTVV WWYY UL VIN LLLLL SSSS Text Datamatrix Name Date code UL & VIN Lot Serial NN-NNNNNNNNNNNNNN-TTTTTTVV WWYY UL VIN LLLLL SSSS Type&Ver Lot number Serial Date code TTTTTTTVV LLLLL SSSS WWYY Outline Pin table [mm] Pin table [mm] Pin X Y Function Pin X Y Function 1 69,1 0 G29 30 0 26,1 DC+Boost1 2 66,1 0 S29 31 0 35,2 Boost1 3 53,6 0 Therm31 32 2,5 35,2 Boost1 4 50,6 0 Therm32 33 5 35,2 Boost1 5 43,8 0 G27 34 13,8 35,2 DC+In1 6 40,8 0 S27 35 16,3 35,2 DC+In1 7 28,3 0 Therm21 36 25,3 35,2 Boost2 8 25,3 0 Therm22 37 27,8 35,2 Boost2 9 18,5 0 G25 38 30,3 35,2 Boost2 10 15,5 0 S25 39 39,1 35,2 DC+In2 11 12 13 3 0 0 0 0 4,1 Therm11 Therm12 DC-Boost1 40 41 41,6 50,6 35,2 35,2 42 53,1 35,2 DC+In2 Boost3 Boost3 14 0 6,6 DC-Boost1 43 55,6 35,2 Boost3 15 0 9,1 DC-Boost1 25,3 4,1 DC-Boost2 64,4 66,9 35,2 35,2 DC+In3 16 44 45 17 25,3 6,6 DC-Boost2 18 25,3 9,1 DC-Boost2 19 50,6 4,1 DC-Boost3 20 50,6 6,6 DC-Boost3 21 50,6 9,1 DC-Boost3 22 50,6 21,1 DC+Boost3 23 50,6 23,6 DC+Boost3 24 50,6 26,1 DC+Boost3 25 25,3 21,1 DC+Boost2 26 25,3 23,6 DC+Boost2 27 25,3 26,1 DC+Boost2 28 0 21,1 DC+Boost1 29 0 23,6 DC+Boost1 Copyright Vincotech DC+In3 5 20 Apr. 2016 / Revision 1 30-FT123BA040MR-L878L08 target datasheet Pinout Identification ID Component Voltage Current Function T25, T27, T29 MOSFET 1200 V 40 mΩ Boost Switch D25, D27, D29 FWD 1200 V 30 A Boost Diode 50 A D26, D28, D30 Rectifier 1600 V C25, C27, C29 Capacitor 1500 V Rt-a, Rt-b, Rt-c Thermistor Copyright Vincotech Comment ByPass Diode Capacitor (DC) Thermistor 6 20 Apr. 2016 / Revision 1 30-FT123BA040MR-L878L08 target datasheet Packaging instruction Standard packaging quantity (SPQ) 42 >SPQ Standard <SPQ Sample Handling instruction Handling instructions for flow 2 packages see vincotech.com website. Package data Package data for flow 2 packages see vincotech.com website. UL recognition and file number This device is certified according to UL 1557 standard, UL file number E192116. For more information see vincotech.com website. Document No.: Date: 30-FT123BA040MR-L878L08-T1-14 20 Apr. 2016 Modification: Pages Product status definition Datasheet Status Product Status Target Formative or In Design Definition This datasheet contains the design specifications for product development. Specifications may change in any manner without notice. The data contained is exclusively intended for technically trained staff. DISCLAIMER The information, specifications, procedures, methods and recommendations herein (together “information”) are presented by Vincotech to reader in good faith, are believed to be accurate and reliable, but may well be incomplete and/or not applicable to all conditions or situations that may exist or occur. Vincotech reserves the right to make any changes without further notice to any products to improve reliability, function or design. No representation, guarantee or warranty is made to reader as to the accuracy, reliability or completeness of said information or that the application or use of any of the same will avoid hazards, accidents, losses, damages or injury of any kind to persons or property or that the same will not infringe third parties rights or give desired results. It is reader’s sole responsibility to test and determine the suitability of the information and the product for reader’s intended use. LIFE SUPPORT POLICY Vincotech products are not authorised for use as critical components in life support devices or systems without the express written approval of Vincotech. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, or (c) whose failure to perform when properly used in accordance with instructions for use provided in labelling can be reasonably expected to result in significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. Copyright Vincotech 7 20 Apr. 2016 / Revision 1