MAXIM MAX3170

19-1703; Rev 0; 4/00
+3.3V, Multiprotocol, 3 Tx/3 Rx, SoftwareSelectable Clock/Data Transceiver
Features
♦ Industry’s First +3.3V Single-Supply Transceiver
♦ 3V/5V Logic-Compatible I/O
♦ Certified TBR-1 and TBR-2 Compliant (NET1 and
NET2)—Pending Completion
♦ Supports V.28 (RS-232), V.11 (RS-449/V.36,
EIA530, EIA530-A, X.21), and V.35 Protocols
♦ Software-Selectable DTE/DCE
♦ Complete DTE/DCE Port with MAX3171/MAX3173
and MAX3172/MAX3174
♦ True Fail-Safe Receiver Operation
♦ Available in Small 28-Pin SSOP Package
♦ 10Mbps Operation (V.11/V.35)
♦ Requires Only Four Tiny Surface-Mount
Capacitors
♦ All Transmitter Outputs Are Fault Protected to
±15V to Survive Cable Miswiring
Ordering Information
________________________Applications
Data Networking
PCI Cards
CSU and DSU
Telecommunications
Data Routers
PART
TEMP. RANGE
MAX3170CAI
0°C to +70°C
PIN-PACKAGE
28 SSOP
Pin Configuration appears at end of data sheet.
Typical Operating Circuit
MAX3171
MAX3173
CTS
DSR
R3
R2
R1
DCD
DTR
RTS
D3
D2
D1
LL
RXD
RXC
R3
R2
TXC
R1
D3
SCTE TXD
D2
D1
MAX3170
MAX3172
MAX3174
R4
12 15 11 24 14 2
TXD B
TXD A
9 17
SCTE B
SCTE A
DB-25 CONNECTOR
16 3
TXC B
TXC A
18
RXD B
RXD A
RXC B
RXC A
7
LL A
DCD B
DCD A
1
SG
DSR B
DSR A
23 20 19 4
SHIELD
22 6
RTS B
RTS A
10 8
DTR B
DTR A
13 5
CTS B
CTS A
D4
________________________________________________________________ Maxim Integrated Products
1
For free samples and the latest literature, visit www.maxim-ic.com or phone 1-800-998-8800.
For small orders, phone 1-800-835-8769.
MAX3170
General Description
The MAX3170 is a three-driver/three-receiver multiprotocol transceiver that operates from a +3.3V single supply. The MAX3170, along with the MAX3171/MAX3173
and MAX3172/MAX3174, form a complete softwareselectable data terminal equipment (DTE) or data communications equipment (DCE) interface port that
supports the V.28 (RS-232), V.11 (RS-449/V.36, EIA530,
EIA530-A, X.21), and V.35 protocols. The MAX3170
transceiver carries the high-speed clock and data signals, while the MAX3171 or MAX3173 carries the control signals. The MAX3170 can be terminated by the
MAX3172 or MAX3174 software-selectable resistor termination network or by a discrete termination network.
An internal charge pump and proprietary low-dropout
transmitter output stage allow V.11-, V.28-, and V.35compliant operation from a +3.3V single supply. A nocable mode is entered when all mode pins (M0, M1,
and M2) are pulled high or left unconnected. In nocable mode, supply current decreases to 1mA and all
transmitter and receiver outputs are disabled (high
impedance). Short-circuit limiting and thermal shutdown circuitry protect the drivers against excessive
power dissipation.
MAX3170
+3.3V, Multiprotocol, 3 Tx/3 Rx, SoftwareSelectable Clock/Data Transceiver
ABSOLUTE MAXIMUM RATINGS
(All voltages referenced to GND unless otherwise noted.)
Supply Voltages
VCC ......................................................................-0.3V to +4V
V+ (Note 1) ..........................................................-0.3V to +7V
V- (Note 1) ...........................................................+0.3V to -7V
V+ to V- (Note 1) ...............................................................13V
Logic Input Voltages
M0, M1, M2, DCE/DTE, T_IN ...............................-0.3V to +6V
Logic Output Voltages
R_OUT ...................................................-0.3V to (VCC + 0.3V)
Short-Circuit Duration............................................Continuous
Transmitter Outputs
T_OUT_...............................................................-15V to +15V
Short-Circuit Duration ........................................................60s
Receiver Inputs
R_IN_ ..................................................................-15V to +15V
Continuous Power Dissipation (TA = +70°C)
28-Pin SSOP (derate 11.1mW/°C above +70°C) ........889mW
Operating Temperature Range
MAX3170CAI .....................................................0°C to +70°C
Storage Temperature Range ............................-65°C to +150°C
Lead Temperature (soldering, 10s) ................................+300°C
Note 1: V+ and V- can have maximum magnitudes of 7V, but their absolute difference cannot exceed 13V.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VCC = +3.3V ±5%, C1 = C2 = 1µF, C3 = C4 = 3.3µF, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C
and VCC = +3.3V.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
190
250
UNITS
DC CHARACTERISTICS
V.11 mode
V.11 mode with no load
Supply Current (DCE Mode)
(Digital Inputs = GND or VCC)
(All Outputs Static)
Internal Power Dissipation
(DCE Mode)
ICC
PD
3
7
V.35 mode
160
210
V.35 mode with no load
20
40
V.28 mode
10
20
V.28 mode with no load
4
7
No-cable mode
0.8
2
V.11 mode, full load
410
V.35 mode, full load
510
V.28 mode, full load
V+ Output Voltage (DCE Mode)
(Full Load)
V+
4
V.35 mode
4.25
V.28 mode
5.55
V
5
V.11 mode
V-
-4.1
V.35 mode
-3.7
V.28 mode
-5.45
No-cable mode
Charge-Pump Enable Time
mW
15
V.11 mode
No-cable mode
V- Output Voltage (DCE Mode)
(Full Load)
mA
V
-4.25
Delay until V+ and V- specifications met
1
ms
LOGIC INPUTS (M0, M1, M2, DCE/DTE, T_IN)
Input High Voltage
VIH
Input Low Voltage
VIL
Logic Input Current
2
2.0
V
0.8
IIN
T_IN
±1
IIH
M0, M1, M2, DCE/DTE = VCC
±1
IIL
M0, M1, M2, DCE/DTE = GND
30
50
_______________________________________________________________________________________
100
V
µA
+3.3V, Multiprotocol, 3 Tx/3 Rx, SoftwareSelectable Clock/Data Transceiver
(VCC = +3.3V ±5%, C1 = C2 = 1µF, C3 = C4 = 3.3µF, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C
and VCC = +3.3V.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
LOGIC OUTPUTS (R_OUT)
Output High Voltage
VOH
ISOURCE = 1.0mA
Output Low Voltage
VOL
ISINK = 1.6mA
Rise or Fall Time
tr, tf
10% to 90%
R_OUT = GND
Output Leakage Current
(Receiver Output Tristated)
VCC - 1.0
V
0.4
15
30
50
ns
100
±1
R_OUT = VCC
V
µA
TRANSMITTER OUTPUTS
Output Leakage Current
IZ
Data Rate
-0.25V < VOUT < +0.25V power-off or
no-cable mode
±100
µA
V.11/ V.35 mode
10
Mbps
V.28 mode
240
kbps
RECEIVER INPUTS
Receiver Input Resistance
RIN
Data Rate
-10V < VA,B < +10V, VA or VB grounded
(V.11/V.35/no-cable mode)
20
40
-15V < VA < +15V (V.28 mode)
3
5
kΩ
7
V.11/ V.35 mode
10
Mbps
V.28 mode
240
kbps
V.11 TRANSMITTER
Unloaded Differential Output
Voltage
VODO
R = 1.95kΩ, Figure 1
Loaded Differential Output
Voltage
VODL
R = 50Ω, Figure 1
Change in Magnitude of Output
∆VOD
R = 50Ω, Figure 1
0.2
V
Common-Mode Output Voltage
VOC
R = 50Ω, Figure 1
3.0
V
Change in Magnitude of Output
Common-Mode Voltage
∆VOC
R = 50Ω, Figure 1
0.2
V
4.0
6.0
2.0
0.5 x VODO
V
V
Short-Circuit Current
ISC
VOUT = GND
60
150
mA
Rise or Fall Time
tr, tf
10% to 90%, Figure 2
10
25
ns
Transmitter Input to Output
Data Skew
Output-to-Output Skew
Channel-to-Channel Output
tPHL, tPLH
Figure 2
50
80
ns
|tPHL - tPLH|
Figure 2
2
10
ns
tSKEW
Figure 2
2
ns
2
ns
V.11 RECEIVER
Differential Threshold Voltage
Input Hysteresis
Receiver Input to Output
Data Skew
VTH
-7V < VCM < +7V
-200
-100
-25
mV
∆VTH
-7V < VCM < +7V
15
tPHL, tPLH
VCM = 0, Figure 2
60
120
ns
|tPHL - tPLH|
VCM = 0, Figure 2
5
16
ns
mV
_______________________________________________________________________________________
3
MAX3170
ELECTRICAL CHARACTERISTICS (continued)
MAX3170
+3.3V, Multiprotocol, 3 Tx/3 Rx, SoftwareSelectable Clock/Data Transceiver
ELECTRICAL CHARACTERISTICS (continued)
(VCC = +3.3V ±5%, C1 = C2 = 1µF, C3 = C4 = 3.3µF, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C
and VCC = +3.3V.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
V.35 TRANSMITTER
Differential Output Voltage
0.44
0.55
0.66
V
Output High Current
IOH
VA, B = 0
9
11
13
mA
Output Low Current
IOL
VA, B = 0
-13
-11
-9
mA
tr, tf
Rise or Fall Time
Transmitter Input to Output
Data Skew
-4V < VCM < +4V, Figure 3
10% to 90%, Figure 3
10
tPHL, tPLH
Figure 3
50
80
ns
|tPHL - tPLH|
Figure 3
5
10
ns
Figure 3
2
ns
2
ns
Output-to-Output Skew
Channel-to-Channel Output Skew
ns
V.35 RECEIVER
Differential Input Voltage
Input Hysteresis
Receiver Input to Output
Data Skew
VTH
-4V < VCM < +4V, Figure 3
∆VTH
-200
-100
-25
mV
-4V < VCM < +4V, Figure 3
15
tPHL, tPLH
VCM = 0
70
120
mV
ns
|tPHL - tPLH|
VCM = 0
5
16
ns
V.28 TRANSMITTER
Output Voltage Swing
VO
Short-Circuit Current
ISC
Output Slew Rate
Transmitter Input to Output
Data Skew
All transmitters loaded with RL = 3kΩ
±5.0
±5.4
±6.5
No load
±25
±60
RL = 3kΩ, CL = 2500pF, measured from
+3V to -3V or -3V to +3V, Figure 4
4
30
RL = 7kΩ, CL = 150pF, measured from
+3V to -3V or -3V to +3V, Figure 4
6
30
SR
V
mA
V/µs
tPHL, tPLH
Figure 4
1
µs
|tPHL - tPLH|
Figure 4
100
ns
VIL
Figure 5
1.1
V
VIH
Figure 5
V.28 RECEIVER
Input Threshold Low
Input Threshold High
Input Hysteresis
Data Skew
4
VHYS
|tPHL - tPLH|
Figure 5
0.8
1.6
2.0
V
0.5
V
100
ns
_______________________________________________________________________________________
+3.3V, Multiprotocol, 3 Tx/3 Rx, SoftwareSelectable Clock/Data Transceiver
150
100
50
MAX3170-02
60
40
0
0.1
1
10
100
1000
10,000
DCE MODE, VCM = 0
ALL TRANSMITTERS OPERATING
AT SPECIFIED RATE
150
100
50
0
0
50
100
150
200
0.1
250
1
10
100
10,000
1000
DATA RATE (kbps)
DATA RATE (kbps)
V.11 DRIVER DIFFERENTIAL OUTPUT
VOLTAGE vs. TEMPERATURE
V.28 OUTPUT VOLTAGE
vs. TEMPERATURE
V.35 DIFFERENTIAL OUTPUT VOLTAGE
vs. TEMPERATURE
OUTPUT VOLTAGE (V)
2
1
0
-1
-2
VOL
-3
-4
-40
-20
0
20
40
60
80
DCE MODE, R = 3kΩ
VOUT+
VOUT-
0.66
0.44
MAX3170-06
VOH
3
8
7
6
5
4
3
2
1
0
-1
-2
-3
-4
-5
-6
-7
-8
DIFFERENTIAL OUTPUT VOLTAGE (V)
DCE MODE, R = 50Ω
MAX3170-05
DATA RATE (kbps)
MAX3170-04
4
VOH
DCE MODE, VCM = 0
0.22
0
-0.22
-0.44
VOL
-0.66
-40
-20
0
20
40
60
-40
80
-20
0
20
40
60
80
TEMPERATURE (°C)
TEMPERATURE (°C)
TEMPERATURE (°C)
V.35 DIFFERENTIAL OUTPUT VOLTAGE
vs. COMMON-MODE VOLTAGE
V.11/V.35 RECEIVER INPUT CURRENT
vs. INPUT VOLTAGE
V.28 RECEIVER INPUT CURRENT
vs. INPUT VOLTAGE
VOH
550
540
530
200
100
0
-100
-200
2.5
2.0
MAX3170-09
DCE MODE
RECEIVER INPUT CURRENT (mA)
560
300
RECEIVER INPUT CURRENT (µA)
MAX3170-07
570
MAX3170-08
DRIVER DIFFERENTIAL OUTPUT VOLTAGE (V)
80
200
20
0
DIFFERENTIAL OUTPUT VOLTAGE (V)
DCE MODE, ALL TRANSMITTERS
OPERATING AT THE SPECIFIED DATA RATE
RL = 3kΩ, CL = 2000pF
V.35 SUPPLY CURRENT (mA)
200
100
MAX3170-01
DCE MODE, R = 50Ω
ALL TRANSMITTERS OPERATING
AT SPECIFIED RATE
V.28 SUPPLY CURRENT (mA)
V.11 SUPPLY CURRENT (mA)
250
V.35 SUPPLY CURRENT
vs. DATA RATE
V.28 SUPPLY CURRENT
vs. DATA RATE
MAX3170-03
V.11 SUPPLY CURRENT
vs. DATA RATE
DCE MODE
1.5
1.0
0.5
0
-0.5
-1.0
-1.5
-2.0
520
-300
-4
-3
-2
-1
0
VCM (V)
1
2
3
4
-2.5
-10 -8
-6
-4
-2
0
2
4
INPUT VOLTAGE (V)
6
8
10
-10 -8
-6
-4
-2
0
2
4
6
8
10
INPUT VOLTAGE (V)
_______________________________________________________________________________________
5
MAX3170
Typical Operating Characteristics
(VCC = +3.3V, C1 = C2 = 1.0µF, C3 = C4 = 3.3µF, TA = +25°C, unless otherwise noted.)
Typical Operating Characteristics (continued)
(VCC = +3.3V, C1 = C2 = 1.0µF, C3 = C4 = 3.3µF, TA = +25°C, unless otherwise noted.)
V.35 LOOPBACK SCOPE PHOTO
V.28 LOOPBACK SCOPE PHOTO
V.11 LOOPBACK SCOPE PHOTO
V.28 SLEW RATE
vs. LOAD CAPACITANCE
V.11 TRANSMITTER PROPAGATION
DELAY vs. TEMPERATURE
V.11 RECEIVER PROPAGATION DELAY
vs. TEMPERATURE
PROPAGATION DELAY (ns)
10
8
-SLEW
4
RL = 3kΩ
1 TRANSMITTER SWITCHING AT 250kbps;
OTHER TRANSMITTERS SWITCHING AT 15kbps
40
tPHL
30
20
10
2000
3000
4000
5000
-20
0
20
40
60
30
20
-40
80
-20
80
40
tPHL
30
20
10
tPLH
70
PROPAGATION DELAY (ns)
tPLH
20
60
tPHL
50
40
30
20
10
0
0
-40
-20
0
20
40
TEMPERATURE (°C)
60
80
40
V.35 RECEIVER PROPAGATION
DELAY vs. TEMPERATURE
MAX3170-16
60
0
TEMPERATURE (°C)
TEMPERATURE (°C)
V.35 TRANSMITTER PROPAGATION
DELAY vs. TEMPERATURE
PROPAGATION DELAY (ns)
tPHL
40
0
-40
LOAD CAPACITANCE (pF)
50
50
MAX3170-17
1000
tPLH
60
10
0
0
MAX3170-15
70
PROPAGATION DELAY (ns)
tPLH
50
80
MAX3170-14
MAX3170-13
60
+SLEW
0
400mV/div
50ns/div
12
6
ROUT
1µs/div
14
2
TOUT/RIN
50ns/div
16
6
2V/div
ROUT
ROUT
2V/div
2V/div
TOUT/RIN
TIN
2V/div
2V/div
5V/div
TIN
TIN
TOUT/RIN
MAX3170-12
MAX3170-11
MAX3170-10
SLEW RATE (V/µs)
MAX3170
+3.3V, Multiprotocol, 3 Tx/3 Rx, SoftwareSelectable Clock/Data Transceiver
-40
-20
0
20
40
60
80
TEMPERATURE (°C)
_______________________________________________________________________________________
60
80
+3.3V, Multiprotocol, 3 Tx/3 Rx, SoftwareSelectable Clock/Data Transceiver
100pF
R
100Ω
VOD
50pF
VOC
R
100pF
Figure 2. V.11 AC Test Circuit
Figure 1. V.11 DC Test Circuit
50Ω
50Ω
125Ω
50Ω
VCM
125Ω
50Ω
50pF
Figure 3. V.35 Transmitter/Receiver Test Circuit
CL
RL
50pF
Figure 4. V.28 Driver Test Circuit
Figure 5. V.28 Receiver Test Circuit
_______________________________________________________________________________________
7
MAX3170
Test Circuits
+3.3V, Multiprotocol, 3 Tx/3 Rx, SoftwareSelectable Clock/Data Transceiver
MAX3170
Pin Description
PIN
NAME
FUNCTION
1
V+
2
C2+
Positive Terminal of the Inverting Charge-Pump Capacitor. Connect C2+ to C2- with a 1µF
ceramic capacitor.
3
C2-
Negative Terminal of the Inverting Charge-Pump Capacitor. Connect C2+ to C2- with a 1µF
ceramic capacitor.
4
V-
5, 6, 7
T_IN
8, 9, 10
R_OUT
11, 12, 13
M_
14
DCE/DTE
15, 18
R_INB
Noninverting Receiver Inputs (R3INB, R2INB)
16, 17
R_INA
Inverting Receiver Inputs (R3INA, R2INA)
19
T3OUTB/R1INB
Noninverting Transmitter Output/Noninverting Receiver Input
20
T3OUTA/R1INA
Inverting Transmitter Output/Inverting Receiver Input
21, 23
T_OUTB
Noninverting Transmitter Outputs (T2OUTB, T1OUTB)
22, 24
T_OUTA
Inverting Transmitter Outputs (T2OUTA, T1OUTA)
25
C1-
26
GND
Ground
27
VCC
+3.3V Supply Voltage (±5%). Bypass V CC to ground with a 3.3µF capacitor.
28
C1+
Positive Terminal of the Voltage-Doubler Charge-Pump Capacitor. Connect C1+ to C1- with a
1µF ceramic capacitor.
Positive Supply Generated by the Charge Pump. Bypass V+ to ground with a 3.3µF ceramic
capacitor.
Negative Supply Generated by the Charge Pump. Bypass V- to ground with a 3.3µF ceramic
capacitor.
Transmitter CMOS Inputs (T1IN, T2IN, T3IN)
Receiver CMOS Outputs (R1OUT, R2OUT, R3OUT)
Mode Select Pins (M0, M1, M2). Internally pulled up to VCC. See Table 1 for detailed
information.
DCE/DTE Mode Select Pin. Logic level high selects DCE interface; logic level low selects
DTE interface. Internally pulled up to VCC.
Negative Terminal of the Voltage-Doubler Charge-Pump Capacitor. Connect C1+ to C1- with
a 1µF ceramic capacitor.
Detailed Description
The MAX3170 is a three-driver/three-receiver multiprotocol transceiver that operates from a +3.3V single supply. The MAX3170, along with the MAX3171/MAX3173
and MAX3172/MAX3174, form a complete softwareselectable DTE or DCE interface port that supports the
V.28 (RS-232), V.11 (RS-449/V.36, EIA530, EIA530-A,
and X.21), and V.35 protocols. The MAX3170 transceiver carries the high-speed clock and data signals, while
the MAX3171 or MAX3173 carries the control signals.
8
The MAX3170 can be terminated by the MAX3172 or
MAX3174 software-selectable resistor termination network or by a discrete termination network.
The MAX3170 features a 1mA no-cable mode, true failsafe operation, and thermal shutdown circuitry. Thermal
shutdown protects the drivers against excessive power
dissipation. When activated, the thermal shutdown circuitry places the driver outputs into a high-impedance
state.
_______________________________________________________________________________________
+3.3V, Multiprotocol, 3 Tx/3 Rx, SoftwareSelectable Clock/Data Transceiver
MAX3170
Table 1. Mode Selection
PROTOCOL
LOGIC INPUTS
TRANSMITTERS
RECEIVERS
M2
M1
M0
DCE/DTE
T1
T2
T3
R1
R2
R3
V.11
0
0
0
0
V.11
V.11
Z
V.11
V.11
V.11
RS-530A
0
0
1
0
V.11
V.11
Z
V.11
V.11
V.11
RS-530
0
1
0
0
V.11
V.11
Z
V.11
V.11
V.11
X.21
0
1
1
0
V.11
V.11
Z
V.11
V.11
V.11
V.35
1
0
0
0
V.35
V.35
Z
V.35
V.35
V.35
RS-449/V.36
1
0
1
0
V.11
V.11
Z
V.11
V.11
V.11
V.28/RS-232
1
1
0
0
V.28
V.28
Z
V.28
V.28
V.28
No cable
1
1
1
0
Z
Z
Z
Z
Z
Z
V.11
0
0
0
1
V.11
V.11
V.11
Z
V.11
V.11
RS-530A
0
0
1
1
V.11
V.11
V.11
Z
V.11
V.11
RS-530
0
1
0
1
V.11
V.11
V.11
Z
V.11
V.11
X.21
0
1
1
1
V.11
V.11
V.11
Z
V.11
V.11
V.35
1
0
0
1
V.35
V.35
V.35
Z
V.35
V.35
RS-449/V.36
1
0
1
1
V.11
V.11
V.11
Z
V.11
V.11
V.28/RS-232
1
1
0
1
V.28
V.28
V.28
Z
V.28
V.28
No cable
1
1
1
1
Z
Z
Z
Z
Z
Z
Z = High impedance
Mode Selection
The state of the mode select pins M0, M1, and M2
determines which serial interface protocol is selected
(Table 1). The state of the DCE/DTE input determines
whether the transceiver will be configured as a DTE or
a DCE serial port. When the DCE/DTE input is logic
HIGH, driver T3 is activated and receiver R1 is disabled. When the DCE/DTE input is logic LOW, driver T3
is disabled and receiver R1 is activated. M0, M1, M2,
and DCE/DTE are internally pulled up to VCC to ensure
a logic HIGH if left unconnected.
The MAX3170’s mode can be selected through software control of the M0, M1, M2, and DCE/DTE inputs.
Alternatively, the mode can be selected by shorting the
appropriate combination of mode control inputs to
GND. The inputs left floating will be internally pulled up
to V CC (logic HIGH). If the M0, M1, and M2 mode
inputs are all unconnected, the MAX3170 will enter nocable mode and the supply current will drop to 1mA.
No-Cable Mode
The MAX3170 will enter no-cable mode when the mode
select pins are left unconnected or tied high (M0 = M1
= M2 = 1). In this mode, the multiprotocol drivers and
receivers are disabled and the supply current drops to
1mA. The receiver outputs enter a high-impedance
state in no-cable mode, which allows these output lines
to be shared with other receivers (the receiver outputs
have an internal pull-up resistor to pull the outputs
HIGH if not driven). Also, in no-cable mode, the transmitter outputs enter a high-impedance state so that
these output lines can be shared with other devices.
Dual Charge-Pump Voltage Converter
The MAX3170’s internal power supply consists of a regulated dual charge pump that provides positive and
negative output voltages from a +3.3V supply. The
charge pump operates in discontinuous mode: if the
output voltage is less than the regulated voltage, the
charge pump is enabled; if the output voltage exceeds
the regulated voltage, the charge pump is disabled.
Each charge pump requires a flying capacitor (C1, C2)
and a reservoir capacitor (C3, C4) to generate the V+
and V- supplies. See Figure 6 for charge-pump connections.
Fail-Safe Receivers
The MAX3170 guarantees a logic-high receiver output
when the receiver inputs are shorted or open, or when
they are connected to a terminated transmission line
with all drivers disabled. This is done by setting the
_______________________________________________________________________________________
9
MAX3170
+3.3V, Multiprotocol, 3 Tx/3 Rx, SoftwareSelectable Clock/Data Transceiver
receiver threshold between -25mV and -200mV in the
V.11 and V.35 modes. If the differential receiver input
voltage (B - A) is ≥-25mV, R_OUT is logic HIGH. If (B A) is ≤ -200mV, R_OUT is logic LOW. In the case of a
terminated bus with all transmitters disabled, the
receiver’s differential input voltage is pulled to zero by
the termination. With the receiver thresholds of the
MAX3170, this results in a logic HIGH with a 25mV minimum noise margin.
Applications Information
1
C3
3.3µF
2
C2
1µF
3
4
MAX3170
V+
C1+
C2+
VCC
C2-
GND
V-
C1-
28
27
26
C5
3.3µF
C1
1µF
25
C4
3.3µF
Capacitor Selection
The capacitors used for the charge pumps, as well as
the supply bypassing, should have a low equivalent
series resistance (ESR) and low temperature coefficient. Multilayer ceramic capacitors with an X7R dielectric offer the best combination of performance, size,
and cost. The flying capacitors (C1, C2) should have a
value of 1µF, while the reservoir capacitors (C3, C4)
and bypass capacitor (C5) should have a minimum
value of 3.3µF (Figure 6). To reduce the ripple present
on the transmitter outputs, capacitors C3, C4, and C5
can be increased. The values of C1 and C2 should not
be increased.
Cable Termination
The MAX3172/MAX3174 software-selectable resistor
network is designed to be used with the MAX3170. The
MAX3172/MAX3174 multiprotocol termination network
provides V.11- and V.35-compliant termination, while
V.28 receiver termination is internal to the MAX3170.
These cable termination networks provide compatibility
with V.11, V.28, and V.35 protocols. Using the
MAX3172/MAX3174 termination network provides the
advantage of not having to build expensive termination
networks out of resistors and relays, manually changing
termination modules, or building termination networks
into custom cables.
Cable-Selectable Mode
A cable-selectable multiprotocol interface is shown in
Figure 7. The mode control lines M0, M1, and DCE/DTE
are wired to the DB-25 connector. To select the serial
interface mode, the appropriate combination of M0,
M1, M2, and DCE/DTE are grounded within the cable
wiring. The control lines that are not grounded are
pulled high by the internal pull-ups on the MAX3170.
The serial interface protocol of the MAX3170 (and
MAX3171/MAX3173 and MAX3172/MAX3174) is selected based on the cable that is connected to the DB-25
interface.
10
Figure 6. Charge-Pump Connections
V.11 (RS-422) Interface
As shown in Figure 8, the V.11 protocol is a fully balanced differential interface. The V.11 driver generates a
minimum of ±2V between nodes A and B when a 100Ω
(min) resistance is presented at the load. The V.11
receiver is sensitive to ±200mV differential signals at
the receiver inputs, A′ and B′. The V.11 receiver rejects
common-mode signals developed across the cable
(referenced from C to C′) of up to ±7V, allowing for
error-free reception in noisy environments. The receiver
inputs must comply with the impedance curve shown in
Figure 9.
For high-speed data transmission, the V.11 specification recommends terminating the cable at the receiver
with a 100Ω minimum resistor. This resistor, although
not required, prevents reflections from corrupting transmitted data. In Figure 10, the MAX3172 or MAX3174 is
used to terminate the V.11 receiver. Internal to the
MAX3172/MAX3174, S1 is closed and S2 is open to
present a 100Ω minimum differential resistance. The
MAX3170’s internal V.28 termination is disabled by
opening S3.
V.35 Interface
Figure 11 shows a fully balanced differential standard
V.35 interface. The generator and the load must both
present a 100Ω ±10Ω differential impedance and a
150Ω ±15Ω common-mode impedance as shown by
the resistive T-networks in Figure 11. The V.35 driver
generates a current output (±11mA typ) that develops
an output voltage of ±550mV across the generator and
load termination networks. The V.35 receiver is sensitive to ±200mV differential signals at the receiver inputs
A′ and B′. The V.35 receiver rejects common-mode signals developed across the cable (referenced from C to
C′) of up to ±4V, allowing for error-free reception in
noisy environments.
______________________________________________________________________________________
+3.3V, Multiprotocol, 3 Tx/3 Rx, SoftwareSelectable Clock/Data Transceiver
R2
R1
D2
D1
SCTE(DTE)
RXC(DCE)
TXC(DTE)
TXD(DTE)
TXC(DCE)
RXD(DCE)
MAX3172
MAX3174
R4
R3
R2
16 3
9 17
R1
D3
D2
D1
D4
MAX3170
M0
M1
M2
DCE/DTE
R3
D3
M0
M1
M2
DCE/DTE
MAX3171
MAX3173
RXD(DTE)
TXD(DCE)
RXC(DTE)
SCTE(DCE)
DTR(DTE)
DSR(DCE)
RTS(DTE)
DCD(DTE)
CTS(DCE)
DCD(DCE)
MAX3170
CTS(DTE)
RTS(DCE)
DSR(DTE)
DTR(DCE)
M0 M1 M2 DCE/DTE
TXD B
TXD A
RXD B
RXD A
RXC B SCTE B
RXC A SCTE A
TXC B
TXC A
DB-25 CONNECTOR
12 15 11 24 14 2
TXC B
TXC A
25
DCE/DTE
RXD B
RXD A
RXC B
RXC A
SG
18 21
M0 M1
TXD B
TXD A
SCTE B
SCTE A
7
SHIELD
RTS B
RTS A
1
CTS B
CTS A
DTR B
DTR A
DCD B
DCD A
23 20 19 4
DSR B
DSR A
DSR B
DSR A
CABLE WIRING FOR
MODE SELECTION
MODE
PIN 18 PIN 21
V.35
PIN 7 PIN 7
RS-449, V.36 N.C.
PIN 7
RS-232
PIN 7 N.C.
NO CABLE
N.C.
N.C.
DCD B
DCD A
22 6
DTR B
DTR A
10 8
DCE
RTS B
RTS A
13 5
DTE
CTS B
CTS A
VCC
CABLE WIRING FOR
DCE/DTE SELECTION
MODE
PIN 25
DTE
PIN 7
DCE
N.C.
Figure 7. Cable-Selectable Multiprotocol DCE/DTE Port
In Figure 12, the MAX3172 or MAX3174 is used to
implement the resistive T-network that is needed to
properly terminate the V.35 driver and receiver. Internal
to the MAX3172/MAX3174, S1 and S2 are closed to
connect the T-network resistors to the circuit. The V.28
termination resistor (internal to the MAX3170) is disabled by opening S3 to avoid interference with the Tnetwork impedances.
V.28 Interface
The V.28 interface is an unbalanced single-ended interface (Figure 13). The V.28 driver generates a minimum
of ±5V across the load impedance between A′ and C′.
The V.28 receiver has a single-ended input and does
not reject any common-mode differences between C
and C′. The V.28 receiver has input trip points at ±3V.
To aid in rejecting system noise, the MAX3170 V.28
receiver has a typical hysteresis of 0.5V.
Figure 14 shows that the MAX3172/MAX3174 termination network is disabled by opening S1 and S2. The
MAX3170’s internal 5kΩ V.28 termination is enabled by
closing S3.
______________________________________________________________________________________
11
MAX3170
+3.3V, Multiprotocol, 3 Tx/3 Rx, SoftwareSelectable Clock/Data Transceiver
IZ
BALANCED
INTERCONNECTING
CABLE
GENERATOR
3.25mA
LOAD
CABLE
TERMINATION
-3V
-10V
RECEIVER
A′
A
+3V
100Ω
MIN
B
B′
C
C′
-3.25mA
Figure 9. Receiver Input Impedance Curve
Figure 8. Typical V.11 Interface
A′
A
MAX3170
R5
30k
R1
51.5Ω
R8
5k
MAX3172
MAX3174
R6
10k
RECEIVER
S3
S1
R3
124Ω
S2
R7
10k
R2
51.5Ω
B′
R4
30k
B
C′
GND
Figure 10. V.11 Termination and Internal Resistance Networks
BALANCED
INTERCONNECTING
CABLE
GENERATOR
A
50Ω
LOAD
A′
125Ω
CABLE
TERMINATION
125Ω
50Ω
RECEIVER
50Ω
50Ω
B
B′
C
C′
Figure 11. Typical V.35 Interface
12
______________________________________________________________________________________
VZ
+10V
+3.3V, Multiprotocol, 3 Tx/3 Rx, SoftwareSelectable Clock/Data Transceiver
MAX3170
A′
A
MAX3170
R5
30k
R1
51.5Ω
R8
5k
MAX3172
MAX3174
R6
10k
RECEIVER
S3
S1
R3
124Ω
S2
R7
10k
R2
51.5Ω
B′
R4
30k
B
C′
GND
Figure 12. V.35 Termination and Internal Resistance Networks
GENERATOR
UNBALANCED
INTERCONNECTING
CABLE
A
LOAD
CABLE
TERMINATION
RECEIVER
A′
This application requires only one DB-25 connector,
but separate cables for DCE or DTE signal routing. See
Figure 15 for complete signal routing in DCE and DTE
modes. For example, the MAX3170’s D3 routes the TXC
(DCE) signal to pins 12 and 15 in DCE mode, while in
DTE mode, the MAX3170’s R1 routes pins 12 and 15 to
TXC (DTE).
Complete Multiprotocol X.21 Interface
C
C′
Figure 13. Typical V.28 Interface
DTE vs. DCE Operation
Figure 15 shows a DCE or DTE controller-selectable
interface. The DCE/DTE pin (pin 14) switches the port’s
mode of operation. A logic HIGH selects DCE, which
enables D3 on the MAX3170, D3 on the MAX3171/
MAX3173, and D4 on the MAX3172/MAX3174. A logic
LOW selects DTE, which enables R1 on the MAX3170,
R1 on the MAX3171/MAX3173, and R4 on the MAX3172/
MAX3174.
A complete DTE-to-DCE interface operating in X.21
mode is shown in Figure 16. The MAX3170 is used to
generate the clock and data signals, and the
MAX3171/MAX3173 generate the control signals. The
MAX3172/MAX3174 generate local loopback (LL), and
are used to terminate the clock and data signals to
support the V.11 protocol for cable termination. The
control signals do not need external termination.
Compliance Testing
A European Standard EN 45001 test report is available
for the MAX3170/MAX3171/MAX3173/MAX3172/
MAX3174 chipset. A copy of the test report will be
available from Maxim upon completion.
______________________________________________________________________________________
13
MAX3170
+3.3V, Multiprotocol, 3 Tx/3 Rx, SoftwareSelectable Clock/Data Transceiver
A′
A
MAX3170
R5
30k
R1
51.5Ω
R8
5k
MAX3172
MAX3174
R6
10k
RECEIVER
S3
S1
R3
124Ω
S2
R7
10k
R2
51.5Ω
B′
R4
30k
B
C′
GND
Figure 14. V.28 Termination and Internal Resistance Networks
RXD(DTE)
TXD(DCE)
LL(DTE)
RXC(DTE)
LL(DCE)
SCTE(DCE)
DTR(DTE)
DSR(DCE)
RTS(DTE)
DCD(DTE)
CTS(DCE)
DCD(DCE)
SCTE(DTE)
RXC(DCE)
TXC(DTE)
TXD(DTE)
TXC(DCE)
RXD(DCE)
MAX3171
MAX3173
R3
R2
R1
D2
D1
M0
M1
M2
DCE/DTE
MAX3172
MAX3174
D3
R4
R3
R2
16 3
9 17
R1
D3
D2
D1
D4
MAX3170
M0
M1
M2
DCE/DTE
CTS(DTE)
RTS(DCE)
DSR(DTE)
DTR(DCE)
TXD B
TXD A
RXD B
RXD A
TXC B
TXC A
TXC B
TXC A
RXC B SCTE B
RXC A SCTE A
RXD B
RXD A
RXC B
RXC A
DB-25 CONNECTOR
12 15 11 24 14 2
TXD B
TXD A
SCTE B
SCTE A
SG
LL A
7 18
LL A
1
SHIELD
RTS B
RTS A
CTS B
CTS A
DTR B
DTR A
DCD B
DCD A
23 20 19 4
DSR B
DSR A
DSR B
DSR A
DCD B
DCD A
22 6
DTR B
DTR A
10 8
DCE
RTS B
RTS A
13 5
DTE
CTS B
CTS A
M0
M1
M2
DCE/DTE
M0 M1 M2 DCE/DTE
Figure 15. Multiprotocol DCE/DTE Port
14
______________________________________________________________________________________
+3.3V, Multiprotocol, 3 Tx/3 Rx, SoftwareSelectable Clock/Data Transceiver
SERIAL
CONTROLLER
MAX3170
DCE
MAX3172
MAX3174
MAX3172
MAX3174
TXD
D1
TXD
SCTE
D2
SCTE
103Ω
103Ω
D3
TXC
R1
RXC
R2
RXD
R3
MAX3170
SERIAL
CONTROLLER
R3
TXD
R2
SCTE
R1
103Ω
103Ω
103Ω
D4
LL
MAX3170
DTE
TXC
D3
TXC
RXC
D2
RXC
RXD
LL
D1
RXD
R4
R4
LL
D4
MAX3171
MAX3173
MAX3171
MAX3173
RTS
D1
RTS
R3
RTS
DTR
D2
DTR
R2
DTR
D3
R1
DCD
R1
DCD
D3
DCD
DSR
R2
DSR
D2
DSR
CTS
R3
CTS
D1
CTS
Figure 16. DCE-to-DTE X.21 Interface
______________________________________________________________________________________
15
Pin Configuration
Chip Information
TRANSISTOR COUNT: 4058
TOP VIEW
V+ 1
28 C1+
C2+ 2
27 VCC
C2- 3
26 GND
V- 4
25 C1-
T1IN 5
T2IN 6
24 T1OUTA
MAX3170
23 T1OUTB
T3IN 7
22 T2OUTA
R1OUT 8
21 T2OUTB
R2OUT 9
20 T3OUTA/R1INA
R3OUT 10
19 T3OUTB/R1INB
M0 11
18 R2INB
M1 12
17 R2INA
M2 13
16 R3INA
DCE/DTE 14
15 R3INB
28 SSOP
Package Information
SSOP.EPS
MAX3170
+3.3V, Multiprotocol, 3 Tx/3 Rx, SoftwareSelectable Clock/Data Transceiver
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
16 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2000 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.