High-reliability discrete products and engineering services since 1977 MCR106 SERIES SILICON CONTROLLED RECTIFIERS FEATURES Available as “HR” (high reliability) screened per MIL-PRF-19500, JANTX level. Add “HR” suffix to base part number. Available as non-RoHS (Sn/Pb plating), standard, and as RoHS by adding “-PBF” suffix. MAXIMUM RATINGS. Rating Symbol Value Unit (1) Peak repetitive off-state voltage (TJ = -40 to +110°C, sine wave, 50 to 60Hz, gate open) MCR106-1 MCR106-2 MCR106-3 MCR106-4 MCR106-5 MCR106-6 MCR106-7 MCR106-8 VDRM VRRM On-state RMS current (180° conduction angles, TC = 93°C) IT(RMS) 4.0 A Average on-state current (180° conduction angles, TC = 93°C) IT(AV) 2.55 A Peak non-repetitive surge current (half-cycle, sine wave, 60Hz, TJ = 110°C) ITSM Circuit fusing consideration (t = 8.3ms) I2t 2.6 A2s Forward peak gate power (pulse width ≤ 1.0µs, TC = 93°C) PGM 0.5 W Forward average gate power (t = 8.3ms, TC = 93°C) PG(AV) 0.1 W IGM 0.2 A Forward peak gate current (pulse width ≤ 1.0µs, TC = 93°C) Peak reverse gate voltage (pulse width ≤ 1.0µs, TC = 93°C) 30 60 100 200 300 400 500 600 V A 25 VRGM V 6.0 Operating junction temperature range TJ -40 to +110 Storage temperature range Tstg -40 to +150 °C - 6.0 In. lb. Mounting torque(2) °C Note 1: VDRM and VRRM for all types can be applied on a continuous basis. Ratings apply for zero or negative gate voltage; positive gate voltage shall not be applied concurrent with negative potential on the anode. Blocking voltages shall not be tested with a constant current source such that the voltage ratings of the devices are exceeded. Note 2: Torque rating applies with use of compression washer. Mounting torque in excess of 6 in. lb. does not appreciably lower case-to-sink thermal resistance. Anode lead and heatsink contact pad are common. For soldering purposes, soldering temperatures should not exceed +200°C. For optimum results, an activated flux is recommended. THERMAL CHARACTERISTICS Characteristic Symbol Maximum Unit Thermal resistance, junction to case RӨJC 3.0 °C/W Thermal resistance, junction to ambient RӨJA 75 °C/W Lead solder temperature (lead length ≥ 1/8” from case, 10s max) TL °C 260 ELECTRICAL CHARACTERISTICS (TC = 25°C unless otherwise specified) Characteristic Symbol Min Typ Max Unit OFF CHARACTERISTICS Peak forward or reverse blocking current (VAK = Rated VDRM or VRRM, RGK = 1000Ω) IDRM, IRRM µA Rev. 20130115 High-reliability discrete products and engineering services since 1977 MCR106 SERIES SILICON CONTROLLED RECTIFIERS TC = 25°C TC = 110°C - - 10 200 - - 2.0 - 10 ON CHARACTERISTICS Peak forward on-state voltage (3) (ITM = 4.0A peak) VTM V Gate trigger current (continuous dc) (4) (VAK = 7V, RL = 100Ω) (TC = -40°C) Gate trigger voltage (continuous dc)(4) (VAK = 7V, RL = 100Ω) Gate non-trigger voltage(4) (VAK = 12V, RL = 100Ω, T J = 110°C) Holding current (VAK = 7V, initiating current = 200mA, gate open) DYNAMIC CHARACTERISTICS Critical rate of rise of off-state voltage (TC = 110°C) dv/dt - V/µs Note 3: Pulse width ≤ 1.0ms, duty cycle ≤ 1%. Note 4: RGK current is not included in measurement. MECHANICAL CHARACTERISTICS Case: TO-126 Marking: Body painted, alpha-numeric Pin out: See below Rev. 20130115 High-reliability discrete products and engineering services since 1977 MCR106 SERIES SILICON CONTROLLED RECTIFIERS Rev. 20130115