VCUT0505B-HD1 www.vishay.com Vishay Semiconductors Bidirectional Symmetrical (BiSy) Single Line ESD-Protection Diode in LLP1006-2L FEATURES • Ultra compact LLP1006-2L package • Low package profile < 0.4 mm • 1-line ESD-protection 2 1 • Working range ± 5 V 21129 • Low leakage current IR < 0.1 μA 20855 • Low load capacitance CD = 18 pF • ESD-protection acc. IEC 61000-4-2 ± 20 kV contact discharge ± 25 kV air discharge MARKING (example only) XY • Soldering can be checked by standard vision inspection; no X-ray necessary 21121 • Pin plating NiPdAu (e4) no whisker growth Bar = pin 1marking X = date code Y = type code (see table below) • e4 - precious metal (e.g. Ag, Au, NiPd, NiPdAu) (no Sn) • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 ORDERING INFORMATION ORDERING CODE TAPED UNITS PER REEL (8 mm TAPE on 7" REEL) MINIMUM ORDER QUANTITY VCUT0505B-HD1-GS08 8000 8000 DEVICE NAME VCUT0505B-HD1 PACKAGE DATA DEVICE NAME PACKAGE NAME TYPE CODE WEIGHT MOLDING COMPOUND FLAMMABILITY RATING MOISTURE SENSITIVITY LEVEL SOLDERING CONDITIONS VCUT0505B-HD1 LLP1006-2L L 0.72 mg UL 94 V-0 MSL level 1 (according J-STD-020) 260 °C/10 s at terminals ABSOLUTE MAXIMUM RATINGS VCUT0505B-HD1 TEST CONDITIONS SYMBOL VALUE UNIT Peak pulse current Acc. IEC 61000-4-5; tp = 8/20 μs; single shot IPPM 3.5 A Peak pulse power Pin 1 to pin 2 acc. IEC 61000-4-5; tp = 8/20 μs; single shot PPP 56 W ± 20 kV PARAMETER ESD immunity Operating temperature Storage temperature Rev. 1.8, 22-Jul-15 Contact discharge acc. IEC 61000-4-2; 10 pulses Air discharge acc. IEC 61000-4-2; 10 pulses Junction temperature VESD ± 25 kV TJ -40 to +125 °C Tstg -55 to +150 °C Document Number: 81852 1 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VCUT0505B-HD1 www.vishay.com Vishay Semiconductors ELECTRICAL CHARACTERISTICS VCUT0505B-HD1 (Tamb = 25 °C, unless otherwise specified) TEST CONDITIONS/REMARKS SYMBOL MIN. TYP. MAX. UNIT Number of lines which can be protected Nchannel - - 1 lines Max. reverse working voltage VRWM - - 5 V at IR = 0.1 μA VR 5 - - V PARAMETER Protection paths Reverse stand-off voltage Reverse voltage Reverse current at VR = 5 V IR - - 0.1 μA Reverse breakdown voltage at IR = 1 mA VBR 7 - - V at IPP = 1 A VC - - 12 V at IPP = IPPM = 3.5 A VC - - 16 V at VR = 0 V; f = 1 MHz CD - 18 20 pF at VR = 2.5 V; f = 1 MHz CD - 14.5 - pF Reverse clamping voltage Capacitance CUT THE SPIKES WITH VCUT0505B-HD1: The VCUT0505B-HD1 is a bidirectional and symmetrical (BiSy) ESD-protection device which clamps positive and negative overvoltage transients to ground. Connected between the signal or data line and the ground the VCUT0505B-HD1 offers a high isolation (low leakage current, low capacitance) within the specified working range. Due to the short leads and small package size of the tiny LLP1006-2L package the line inductance is very low, so that fast transients like an ESD-strike can be clamped with minimal over- or undershoots. TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) 20 120 % 100 % Discharge Current IESD f = 1 MHz 18 Rise time = 0.7 ns to 1 ns 16 14 CD (pF) 80 % 60 % 53 % 12 10 8 40 % 6 27 % 4 20 % 2 0 0% -10 0 10 20 30 40 50 60 70 80 90 100 0 1 2 21122 Time (ns) 20557 Fig. 1 - ESD Discharge Current Wave Form acc. IEC 61000-4-2 (330 /150 pF) 3 4 5 6 VR (V) Fig. 3 - Typical Capacitance CD vs. Reverse Voltage VR 10 8 µs to 100 % 100 % 8 Pin 1 to 2 6 80 % VR (V) 4 IPPM 60 % 20 µs to 50 % 40 % 2 0 -2 -4 -6 20 % -8 0% 0 10 20 30 40 Time (µs) Fig. 2 - 8/20 μs Peak Pulse Current Wave Form acc. IEC 61000-4-5 20548 Rev. 1.8, 22-Jul-15 - 10 0.01 21123 0.1 1 10 100 1000 10 000 IR (µA) Fig. 4 - Typical Reverse Voltage VR vs. Reverse Current IR Document Number: 81852 2 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VCUT0505B-HD1 www.vishay.com Vishay Semiconductors 40 10 Pin 2 to 1 8 Pin 2 to 1 6 4 0 VC-ESD (V) VR (V) Acc. IEC 61000-4-2 - 8 kV contact discharge 20 2 0 -2 - 20 - 40 -4 -6 - 60 -8 - 10 0.01 0.1 1 10 - 80 -10 0 100 1000 10 000 Fig. 5 - Typical Reverse Voltage VR vs. Reverse Current IR t (ns) Fig. 8 - Typical Clamping Performance at - 8 kV Contact Discharge (acc. IEC 61000-4-2) 200 20 Pin 2 to 1 15 Pin 2 to 1 Positive surge 150 Positive discharge 100 10 0 50 VC-ESD (V) Measured acc. IEC 61000-4-5 (8/20 µs - wave form) 5 VC (V) 10 20 30 40 50 60 70 80 90 21127 IR (µA) 21124 VC -5 VC-ESD 0 - 50 - 100 - 10 Negative discharge - 150 Negative surge Acc. IEC 61000-4-2 contact discharge - 200 - 15 0 1 21125 2 3 0 4 IPP (A) Fig. 6 - Typical Peak Clamping Voltage VC vs. Peak Pulse Current IPP 21128 5 10 15 20 25 VESD (kV) Fig. 9 - Typical Peak. Clamping Voltage at ESD Contact Discharge (acc. IEC 61000-4-2) 80 70 60 Pin 2 to 1 Acc. IEC 61000-4-2 + 8 kV contact discharge VC-ESD (V) 50 40 30 20 10 0 - 10 - 20 - 10 0 21126 10 20 30 40 50 60 70 80 90 t (ns) Fig. 7 - Typical Clamping Performance at + 8 kV Contact Discharge (acc. IEC 61000-4-2) Rev. 1.8, 22-Jul-15 Document Number: 81852 3 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 VCUT0505B-HD1 www.vishay.com Vishay Semiconductors 0.25 [0.010] 0.15 [0.006] PACKAGE DIMENSIONS in millimeters (Inches): LLP1006-2L 0.65 [0.026] 0.55 [0.022] Orientation identification 0.05 [0.002] 0 [0.000] 0.4 [0.016] 0.33 [0.013] 0.45 [0.018] 0.35 [0.014] 0.125 [0.005] ref. 0.55 [0.022] 0.45[0.018] 0.3 [0.012] 0.2 [0.008] 1.05 [0.041] 0.95 [0.037] 1 [0.039] solder resist mask solder pad 0.05 [0.002] Document no.: S8-V-3906.04-005 (4) Rev. 6 - Date: 15.July 2015 20812 0.2 [0.008] 0.5 [0.020] 0.6 [0.024] Foot print recommendation: 0.25 [0.010] 0.5 [0.020] soldermask opening ± 0.03 measured middle of the package Pad design patented: ( ℗ US 9,018,537 B2) Unreeling direction Bidirectional LLP1006-xx Pin 1 mark Top view Rev. 1.8, 22-Jul-15 Pad layout - view from top seen at bottom side Document Number: 81852 4 For technical questions, contact: [email protected] THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Material Category Policy Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (EEE) - recast, unless otherwise specified as non-compliant. Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU. Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21 conform to JEDEC JS709A standards. Revision: 02-Oct-12 1 Document Number: 91000