5962-09201

REVISIONS
LTR
DESCRIPTION
DATE (YR-MO-DA)
APPROVED
A
Table I; changed the max limit for the Dropout voltage test from 1.55 V
to 1.30 V. Removed 3/ on the Standard Microcircuit Drawing Bulletin
page and added Vendor CAGE number 88379. -sld
09-10-01
Charles F. Saffle
B
Added case outline T. -sld
10-06-22
Charles F. Saffle
C
Added radiation hardness assurance requirements. -sld
12-04-11
Charles F. Saffle
D
Added ELDRS requirements. Updated paragraphs 1.3 and 1.4.
Editorial changes throughout. -sld
13-10-15
Charles F. Saffle
REV
SHEET
REV
D
D
D
D
D
D
D
D
D
D
D
SHEET
15
16
17
18
19
20
21
22
23
24
25
REV
D
D
D
D
D
D
D
D
D
D
D
D
D
D
SHEET
1
2
3
4
5
6
7
8
9
10
11
12
13
14
REV STATUS
OF SHEETS
PMIC N/A
STANDARD MICROCIRCUIT
DRAWING
THIS DRAWING IS
AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
AMSC N/A
PREPARED BY
Steve Duncan
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
http://www.landandmaritime.dla.mil/
CHECKED BY
Greg Cecil
APPROVED BY
Charles F. Saffle
DRAWING APPROVAL DATE
MICROCIRCUIT, HYBRID, DUAL VOLTAGE
REGULATOR, POSITIVE AND NEGATIVE,
LOW DROPOUT, ADJUSTABLE
09-08-19
REVISION LEVEL
D
SIZE
A
SHEET
DSCC FORM 2233
APR 97
CAGE CODE
67268
1
OF
5962-09201
25
5962-E565-13
1. SCOPE
1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A
choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When
available, a choice of radiation hardness assurance levels are reflected in the PIN.
1.2 PIN. The PIN shall be as shown in the following example:
5962



Federal
stock class
designator
\
R



RHA
designator
(see 1.2.1)
\/
Drawing number
09201
/
01



Device
type
(see 1.2.2)
K



Device
class
designator
(see 1.2.3)
U



Case
outline
(see 1.2.4)
C



Lead
finish
(see 1.2.5)
1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA
levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device.
1.2.2 Device type(s). The device type(s) identify the circuit function as follows:
Device type
Generic number
01
8651, 8652
02
8657, 8658
Circuit function
Dual voltage regulator, positive and negative, low
dropout, adjustable
Dual voltage regulator, positive, low dropout, adjustable
1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level.
All levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K,
and E) or QML Listing (Class G and D). The product assurance levels are as follows:
Device class
Device performance documentation
K
Highest reliability class available. This level is intended for use in space
applications.
H
Standard military quality class level. This level is intended for use in applications
where non-space high reliability devices are required.
G
Reduced testing version of the standard military quality class. This level uses the
Class H screening and In-Process Inspections with a possible limited temperature
range, manufacturer specified incoming flow, and the manufacturer guarantees (but
may not test) periodic and conformance inspections (Group A, B, C and D).
E
Designates devices which are based upon one of the other classes (K, H, or G)
with exception(s) taken to the requirements of that class. These exception(s) must
be specified in the device acquisition document; therefore the acquisition document
should be reviewed to ensure that the exception(s) taken will not adversely affect
system performance.
D
Manufacturer specified quality class. Quality level is defined by the manufacturers
internal, QML certified flow. This product may have a limited temperature range.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09201
A
REVISION LEVEL
D
SHEET
2
1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter
X
Y
U
T
Z
Descriptive designator
See figure 1
See figure 1
See figure 1
See figure 1
See figure 1
Terminals
Package style
6
6
8
6
8
Thru-Hole
Surface Mount
Thru-hole
Surface Mount with unformed leads
Surface Mount
1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534.
1.3 Absolute maximum ratings. 1/
Input voltage:
Positive regulator:
Device type 01 and 02 ........................................................
Negative regulator:
Device type 01....................................................................
Input-Output differential voltage:
Positive regulator:
Device types 01and 02 ......................................................
Negative regulator:
Device type 01....................................................................
DC output current:
Positive regulator:
Device types 01and 02 ......................................................
Negative regulator:
Device type 01....................................................................
Junction temperature (TJ) ..........................................................
Thermal resistance, junction-to-case (θJC) each regulator .........
Lead temperature (soldering, 10 seconds) ................................
Storage temperature range ........................................................
25+VREF
-35 V
25 V
30 V
1.5 A
4.5 A
+150°C
5°C/W
300°C
-65°C to +150°C
1.4 Recommended operating conditions.
Output voltage range:
Postive voltage regulator:
Device types 01 and 02 .....................................................
Negative voltage regulator:
Device type 01....................................................................
DC output current:
Positive regulator:
Device types 01and 02 ......................................................
Negative regulator:
Device type 01....................................................................
Case operating temperature range (TC) ......................................
+1.275 V to +23 V dc
-2.45 V to -25 V dc
1.0 A maximum
3.0 A maximum
-55°C to +125°C
________
1/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the
maximum levels may degrade performance and affect reliability.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09201
A
REVISION LEVEL
D
SHEET
3
1.5 Radiation features. 2/
Maximum total dose available (dose rate = 50 - 300 rad(Si)/s) ....
Enhanced Low Dose Rate Sensitvity (ELDRS):
(dose rate ≤ 10 mrad(Si)/s) ..........................................................
100 krad(Si) 3/
50 krad(Si) 4/
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATIONS
MIL-PRF-38534 - Hybrid Microcircuits, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 - Test Method Standard Microcircuits.
MIL-STD-1835 - Interface Standard Electronic Component Case Outlines.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 - List of Standard Microcircuit Drawings.
MIL-HDBK-780 - Standard Microcircuit Drawings.
(Copies of these documents are available online at http://quicksearch.dla.mil/ or from the Standardization Document Order
Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in
accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 shall include the performance of all tests herein or as
designated in the device manufacturer's Quality Management (QM) plan or as designated for the applicable device class. The
manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as
defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not
affect the form, fit, or function of the device for the applicable device class.
________
2/ Bipolar device types may degrade from displacement damage from radiation which could affect RHA levels. These device
types have not been characterized for displacement damage.
3/ The active elements that make up the devices on this drawing have been tested for Total Ionizing Dose (TID) in accordance
with MIL-STD-883 test method 1019 condition A. RHA testing of the active elements covered on this SMD were tested in
alternate packages (TO3) and (TO39), not the packages as specified in paragraph 1.2.4.
4/ The active elements that make up the devices on this drawing have been tested for Enhanced Low Dose Rate Sensitivity
(ELDRS) in accordance with MIL-STD-883, Method 1019 condition D and paragraph 3.13.1 for initial qualification. No
ELDRS effect was observed. The active elements will be re-tested after design or process changes that can affect RHA
response of these elements.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09201
A
REVISION LEVEL
D
SHEET
4
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
in MIL-PRF-38534 and herein.
3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.
3.2.3 Block diagram. The block diagram shall be as specified on figure 3.
3.2.4 Radiation exposure circuits. The radiation exposure circuits shall be maintained by the manufacturer under document
revision level control and shall be made available to the preparing and acquiring activity upon request.
3.2.5 Maximum power dissipation verses case temperature table. The maximum power dissipation verses case temperature
is specified in table IA.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
as specified in table I and shall apply over the full specified operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are defined in table I.
3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with
the PIN listed in 1.2 herein. In addition, the manufacturer's vendor similar PIN may also be marked.
3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described
herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample,
for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those
which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be
made available to the preparing activity (DLA Land and Maritime -VA) upon request.
3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this
drawing. The certificate of compliance (original copy) submitted to DLA Land and Maritime -VA shall affirm that the
manufacturer's product meets the performance requirements of MIL-PRF-38534 and herein.
3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of
microcircuits delivered to this drawing.
4. VERIFICATION
4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as
modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form,
fit, or function as described herein.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09201
A
REVISION LEVEL
D
SHEET
5
TABLE I. Electrical performance characteristics.
Test
Symbol
Conditions
-55°C ≤ TC ≤+125°C
P ≤ PMAX
unless otherwise specified
Group A
subgroups
Device
types
1.5 V ≤ (VIN - VOUT) ≤ 15 V,
ILOAD = 10 mA
1,2,3
01,02
Limits
Unit
Min
Max
1.210
1.275
V
POSITIVE REGULATOR
Reference voltage 1/
VREF
Line regulation 1/ 2/
ΔVOUT
ΔVIN
1.5 V ≤ (VIN - VOUT) ≤ 15 V,
ILOAD = 10 mA
1,2,3
01,02
0.25
%
Load regulation 1/ 2/
ΔVOUT
ΔIOUT
10 mA ≤ IOUT ≤ 1.0 A, (VIN - VOUT)
=3V
1,2,3
01,02
0.3
%
30 ms pulse, TC = +25°C
1
01,02
0.04
%/W
∆VREF = 1%, IOUT = 1.0 A
1,2,3
01,02
1.30
V
IOUT = 1.0 A, (VIN - VOUT) = 3 V,
f = 120 Hz, CADJ = COUT = 25 µF
1,2,3
01,02
1
01,02
120
µA
Thermal regulation 3/
Dropout voltage 1/
VDROP
Ripple rejection 3/
60
dB
Adjustment pin current
1/
IADJ
TC = +25°C
Adjustment pin current
change 1/
∆IADJ
10 mA ≤ IOUT ≤ 1.0 A,
1.5 V ≤ (VIN - VOUT) ≤ 15 V
1,2,3
01,02
5
µA
Minimum load current
1/ 3/
IMIN
(VIN - VOUT) = 25 V
1,2,3
01,02
10
mA
Current limit 1/
IMAX
(VIN - VOUT) = 5 V, TC = +25°C
1
01,02
(VIN - VOUT) ≤ 25 V, TC = +25°C
1
Burn-in: TC = +125°C at 1000
hours minimum, tested at +25°C
1
01,02
1,3
01
VREF Long term stability
3/
ΔVOUT
ΔTIME
1.5
A
0.047
0.3
%
-2.45
V
NEGATIVE REGULATOR
Reference voltage 1/
VREF
VIN - VOUT = -1.2 V to -28 V,
1 mA ≤ IOUT ≤ 3 A, VOUT = -5 V,
TC = +25°C and -55°C
-2.29
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09201
A
REVISION LEVEL
D
SHEET
6
TABLE I. Electrical performance characteristics - Continued.
Test
Symbol
Conditions
-55°C ≤ TC ≤+125°C
P ≤ PMAX
unless otherwise specified
Group A
subgroups
Device
types
Limits
Min
Unit
Max
NEGATIVE REGULATOR - CONTINUED
Dropout Voltage 1/
VDROP
IOUT = 0.5 A, VOUT = -5 V
1,2,3
01
IOUT = 3 A, VOUT = -5 V
Ripple rejection 3/
V
0.425
1.05
IOUT = 1.0 A, (VIN - VOUT) = 3 V,
f = 120 Hz, CADJ = COUT = 25 µF
1,2,3
01
60
dB
Line regulation 1/ 2/
ΔVOUT
ΔVIN
1 V ≤ (VIN - VOUT) ≤ 20 V,
VOUT = -5 V
1,2,3
01
0.02
%/V
Load regulation 1/ 2/
ΔVOUT
ΔIOUT
5 mA ≤ IOUT ≤ 3 A, (VIN - VOUT) =
-1.5 V to -10 V, VOUT = -5 V
1,2,3
01
0.8
%
1
01
0.014
%/W
1,2,3
01
-4.5
1
01
3.3
4.55
(VIN - VOUT) =-15 V,
TC = +25°C
2.0
4.5
(VIN - VOUT) = -20 V,
TC = +25°C
1.0
3.1
0.2
1.6
2.7
3. 7
0.9
1.6
Thermal regulation 3/
VIN - VOUT = 10 V, IOUT = 5 mA to 2
A, TC = +25°C
Minimum input voltage 1/
VIN MIN
IOUT = 3 A, VOUT = VREF
Internal Current limit 1/
IMAX
-1.5 V ≤ (VIN - VOUT) ≤ -10 V,
TC = +25°C
(VIN - VOUT) = -30 V,
TC = +25°C
External current limit 1/
ILIM
3/
1,2,3
RLIM = 5 kΩ
01
RLIM = 15 kΩ
V
A
A
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09201
A
REVISION LEVEL
D
SHEET
7
TABLE I. Electrical performance characteristics - Continued.
Test
Symbol
Conditions
-55°C ≤ TC ≤+125°C
P ≤ PMAX
unless otherwise specified
Group A
subgroups
Device
types
Limits
Min
Unit
Max
NEGATIVE REGULATOR - CONTINUED
Quiescent supply current
1/
IQ
IOUT = 5 mA, VOUT = VREF,
(-4 V ≤ VIN ≤ -25 V)
1,2,3
01
3.5
mA
Supply current change
with load 1/
IQ∆
(VIN - VOUT) = .25 V +(.25Ω x IOUT)
1,2,3
01
35
mA/A
21
(VIN - VOUT) ≥ -2 V
1/
The active elments that make up these devices have been tested to 200 krad(Si)) to assure RHA designator level "R" (100
krad(Si)) of Method 1019, condition A of MIL-STD-883 at +25°C for these parameters. RHA testing for Total Ionizing Dose
(TID) of the active elements covered on this SMD were done in alternate packages (TO3) and (TO39), not the packages as
specified in paragraph 1.2.4.
2/
Regulation is measured at a constant junction temperature, using pulse testing with a low duty cycle. Changes in
output voltage due to heating effects are covered under the specification for thermal regulation. Measurements taken at
the output lead must be adjusted for lead resistance.
3/
Parameter shall be tested at intial device characterization and after design or process changes. Parameter shall be
guaranteed to the limits specified in table I for all lots not specifically tested.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09201
A
REVISION LEVEL
D
SHEET
8
Table IA. Maximum power dissipation verses case temperature table.
Case
Temperature
(°C)
0
5
10
15
20
25
30
35
40
45
50
55
60
65
70
75
80
85
90
95
100
105
110
115
120
125
130
135
140
145
150
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
Maximum power dissipation
(Watts)
One regulator
"ON"
30
29
28
27
26
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
0
Both regulators
"ON"
53
51
49
48
46
44
42
41
39
37
35
34
32
30
28
26
25
23
21
19
18
16
14
12
11
9
7
5
4
2
0
SIZE
5962-09201
A
REVISION LEVEL
D
SHEET
9
Case U
FIGURE 1. Case outline(s).
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09201
A
REVISION LEVEL
D
SHEET
10
Case U - Continued.
Inches
Symbol
Min
A
Millimeters
Max
Min
.220
Max
5.59
∅b
.028
.032
0.71
0.81
∅b3
.085
.095
2.12
2.41
D
.750
.760
19.05
19.30
D1
.510
.520
12.95
13.21
e
.100 BSC
2.54 BSC
e1
.300 BSC
7.62 BSC
e2
.108 BSC
2.74 BSC
eA
.700
.740
17.78
18.80
E
.410
.420
10.41
10.67
F
.035
.045
0.90
1.14
G1
.632 BSC
G2
.2025
L1
.230
L2
.2125
16.05 BSC
5.144
5.84
.150 REF
.140
∅p
5.408
3.81 REF
.150
3.56
3.81
Q
.122 TYP
3.10 TYP
R
.065 TYP
1.65 TYP
S1
.028
0.71
NOTES:
1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of
measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound
units shall rule.
2. The package contains a BeO substrate.
3. The case is electrically isolated.
FIGURE 1. Case outline(s) - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09201
A
REVISION LEVEL
D
SHEET
11
Case T
FIGURE 1. Case outline(s) - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09201
A
REVISION LEVEL
D
SHEET
12
Case outline T - continued.
Inches
Symbol
Min
A
Millimeters
Max
Min
Max
.220
5.59
∅b
.028
.032
0.71
0.81
∅b3
.085
.095
2.12
2.41
D
.650
.660
16.51
16.76
D1
.410
.420
10.41
10.67
e
.100 BSC
2.54 BSC
e1
.200 BSC
5.08 BSC
e2
.108 BSC
2.74 BSC
E
.410
.420
10.41
10.67
F
.035
.045
0.90
1.14
G1
.123 BSC
G2
.2025
L
.400
∅p
.140
.2125
3.12 BSC
5.144
5.408
10.16
.150
3.56
3.81
Q
.122 TYP
3.10 TYP
R
.065 TYP
1.65 TYP
S1
.028
0.71
NOTES:
1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of
measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound
units shall rule.
2. The package contains a BeO substrate.
3. The case is electrically isolated.
FIGURE 1. Case outline(s) - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09201
A
REVISION LEVEL
D
SHEET
13
Case outline X.
FIGURE 1. Case outline(s) - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09201
A
REVISION LEVEL
D
SHEET
14
Case outline X - Continued.
Inches
Symbol
Min
Millimeters
Max
A
Min
Max
.220
5.59
∅b
.028
.032
0.71
0.81
∅b3
.085
.095
2.12
2.41
D
.650
.660
16.51
16.76
D1
.410
.420
10.41
10.67
e
.100 BSC
2.54 BSC
e1
.200 BSC
5.08 BSC
e2
.108 BSC
2.74 BSC
eA
.700
.740
17.78
18.80
E
.410
.420
10.41
10.67
F
.035
.045
0.90
1.14
G1
.123 BSC
G2
.2025
L1
.230
L2
3.12 BSC
.2125
5.144
5.84
.150 REF
.140
∅p
5.408
3.81 REF
.150
3.56
3.81
Q
.122 TYP
3.10 TYP
R
.065 TYP
1.65 TYP
S1
.028
0.71
NOTES:
1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of
measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound
units shall rule.
2. The package contains a BeO substrate.
3. The case is electrically isolated.
FIGURE 1. Case outline(s) - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09201
A
REVISION LEVEL
D
SHEET
15
Case outline Y.
FIGURE 1. Case outline(s) - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09201
A
REVISION LEVEL
D
SHEET
16
Case outline Y - continued.
Inches
Symbol
Min
A
Millimeters
Max
Min
Max
.220
5.59
A2
.015
.025
0.38
0.64
∅b
.028
.032
0.71
0.81
∅b3
.085
.095
2.12
2.41
D
.650
.660
16.51
16.76
D1
.410
.420
10.41
10.67
e
.100 BSC
2.54 BSC
e1
.200 BSC
5.08 BSC
e2
.108 BSC
2.74 BSC
E
.410
.420
10.41
10.67
F
.035
.045
0.90
1.14
G1
.123 BSC
3.12 BSC
G2
.2025
.2125
5.144
5.408
H
.866
.906
22.00
23.01
L1
.055
.065
1.40
1.65
L2
.150 REF
.140
∅p
3.81 REF
.150
3.56
3.81
Q
.122 TYP
3.10 TYP
R
.065 TYP
1.65 TYP
S1
.028
0.71
NOTES:
1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of
measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound
units shall rule.
2. The package contains a BeO substrate.
3. The case is electrically isolated.
FIGURE 1. Case outline(s) - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09201
A
REVISION LEVEL
D
SHEET
17
Case Z
FIGURE 1. Case outlines(s) - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09201
A
REVISION LEVEL
D
SHEET
18
Case Z - Continued.
Inches
Symbol
Min
Millimeters
Max
A
Min
Max
.220
5.59
A1
.015
.025
0.38
0.64
∅b
.028
.032
0.71
0.81
∅b3
.085
.095
2.12
2.41
D
.750
.760
19.05
19.30
D1
.510
.520
12.95
13.21
e
.100 BSC
2.54 BSC
e1
.300 BSC
7.62 BSC
e2
.108 BSC
2.74 BSC
E
.410
.420
10.41
10.67
F
.035
.045
0.90
1.14
G1
.632 BSC
16.05 BSC
G2
.2025
.2125
5.144
5.408
H
.866
.906
22.00
23.01
L1
.055
.065
1.40
1.65
L2
.150 REF
.140
∅p
3.81 REF
.150
3.56
3.81
Q
.122 TYP
3.10 TYP
R
.065 TYP
1.65 TYP
S1
.028
0.71
NOTES:
1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of
measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound
units shall rule.
2. The package contains a BeO substrate.
3. The case is electrically isolated.
FIGURE 1. Case outline(s) - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09201
A
REVISION LEVEL
D
SHEET
19
Device types
Case outlines
Terminal number
01
02
U and Z
X , Y and T
Terminal symbol
POS_ ADJ_1
NEG_REF_2
NEG_VOUT_2
NEG_VIN_2
NEG_GND_2
NEG_FB_2
POS_VOUT_1
POS_VIN_1
1
2
3
4
5
6
7
8
POS_ADJ_1
POS_VOUT_1
POS_VIN_1
POS_ADJ_2
POS_VIN_2
POS_VOUT_2
FIGURE 2. Terminal connections.
Device type 01
FIGURE 3. Block diagram.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09201
A
REVISION LEVEL
D
SHEET
20
Device type 02
FIGURE 3. Block diagram - Continued.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09201
A
REVISION LEVEL
D
SHEET
21
TABLE II. Electrical test requirements.
MIL-PRF-38534 test requirements
Subgroups
(in accordance with
MIL-PRF-38534, group A
test table)
Interim electrical parameters
1
Final electrical parameters
1,2,3
Group A test requirements
1,2,3
Group C end-point electrical
parameters
1,2,3
End-point electrical parameters
for Radiation Hardness Assurance
(RHA) devices
1
* PDA applies to subgroup 1.
4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply:
a.
b.
Burn-in test, method 1015 of MIL-STD-883.
(1)
Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level
control and shall be made available to either DLA Land and Maritime -VA or the acquiring activity upon request.
Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance
with the intent specified in method 1015 of MIL-STD-883.
(2)
TA as specified in accordance with table I of method 1015 of MIL-STD-883.
Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter
tests prior to burn-in are optional at the discretion of the manufacturer.
4.3 Conformance and periodic inspections. Conformance inspection (CI) and periodic inspection (PI) shall be in accordance
with MIL-PRF-38534 and as specified herein.
4.3.1 Group A inspection (CI). Group A inspection shall be in accordance with MIL-PRF-38534 and as follows:
a.
Tests shall be as specified in table II herein.
b.
Subgroups 4, 5, 6, 7, 8A, 8B, 9, 10, and 11 shall be omitted.
4.3.2 Group B inspection (PI). Group B inspection shall be in accordance with MIL-PRF-38534.
4.3.3 Group C inspection (PI). Group C inspection shall be in accordance with MIL-PRF-38534 and as follows:
a.
End-point electrical parameters shall be as specified in table II herein.
b.
Steady-state life test, method 1005 of MIL-STD-883.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09201
A
REVISION LEVEL
D
SHEET
22
(1)
Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level
control and shall be made available to either DLA Land and Maritime -VA or the acquiring activity upon request.
Also, the test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance
with the intent specified in method 1005 of MIL-STD-883.
(2)
TA as specified in accordance with table I of method 1005 of MIL-STD-883.
(3)
Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.
4.3.4 Group D inspection (PI). Group D inspection shall be in accordance with MIL-PRF-38534.
4.3.5. Radiation hardness assurance (RHA). RHA qualification is required only for those devices with the RHA designator as
specified herein. See table IIIA and table IIIB.
Table IIIA. Radiation Hardness Assurance Method Table.
RHA
method
Employed
Total Dose Testing
Worst Case Analysis Performed
RHA level "R"
No
(100 krad)
Element
Hybrid
Includes
Combines
Combines End-of-life
Level
Device Level temperature temperature and total dose
effects
radiation effects
and
displacement
effects
(200 krad)
NOTES:
X =
G =
(N) =
N/A =
(200 krad)
See
4.3.5.1.1.2
N/A
N/A
N/A
N/A
End point electricals after
total dose
Element Level
Hybrid device
level
TC = +25°C
TC = +25°C
Radiation testing done (Level)
Guaranteed by design or process
Not yet tested
Not applicable for this SMD
Table IIIB. Hybrid level and element level test table.
Hybrid
Low Dose Rate
(LDR)
Total Dose
High Dose Rate
(HDR)
X
See 4.3.5.1.1.2
X
See 4.3.5.1.1.2
Radiation Test
Heavy Ion
Proton
Neutron
ELDRS
SEU
SEL
Low
High
SEE Displacement
(upset) (latch-up) Energy Energy (upset) Damage (DD)
X
See 4.3.5.1.1.2
(N)
(N)
(N)
(N)
(N)
(N)
See notes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09201
A
REVISION LEVEL
D
SHEET
23
Table IIIB. Hybrid level and element level test table - Continued.
Total Dose
Low Dose High Dose Rate
Rate
(HDR)
(LDR)
Element
X
Bipolar, linear or
mixed signal > 90 (50 krad)
nm
NOTES:
X =
G =
(N) =
N/A =
X
(200 krad)
ELDRS
X
(50 krad)
Radiation Test
Heavy Ion
SEU
SEL
(upset)
(latch-up)
(N)
(N)
Proton
Low
High
Energy Energy
(N)
(N)
Neutron
SEE Displacement
(upset) Damage (DD)
(N)
(N)
Radiation testing done (Level)
Guaranteed by design or process
Not yet tested
Not applicable for this SMD
4.3.5.1 Radiation Hardness Assurance (RHA) inspection. RHA qualification is required for those devices with the RHA
designator as specified herein. End-point electrical parameters for radiation hardness assurance (RHA) devices shall be
specified in table II. Radiation testing will be in accordance with the qualifying activity (DLA Land and Maritime -VQ) approved
plan and with MIL-PRF-38534, Appendix G.
a.
The hybrid device manufacturer shall establish procedures controlling component radiation testing, and shall establish
radiation test plans used to implement component lot qualification during procurement. Test plans and test reports
shall be filed and controlled in accordance with the manufacturer's configuration management system.
b.
The hybrid device manufacturer shall designate a RHA program manager to oversee component lot qualification, and
to monitor design changes for continued compliance to RHA requirements.
4.3.5.1.1 Hybrid level qualification.
4.3.5.1.1.1 Qualification by similarity. This device has not been indentified as "similar".
4.3.5.1.1.2 Total ionizing dose irradiation testing. Hybrid level and element level testing are the same for the devices on
this SMD since the active elements are independent of each other and accessible to the device leads for test. The qualification
was performed on the active elements, independent of the hybrid.
4.3.5.1.2 Element level qualification.
4.3.5.1.2.1 Total Ionizing dose irradiation testing. A minimum of ten samples of each element is tested at initial qualification
and after any design or process changes which may affect the RHA response of the device type. Five biased and five unbiased
are tested at High Dose Rate (HDR) in accordance with condition A of method 1019 of MIL-STD-883 to 200 krad(Si). In
addition another ten devices are tested at Low Dose Rate (LDR) in accordance with method 1019, condition D and paragraph
3.13.1 of MIL-STD-883 to 50 krad(Si). The resulting data is evaluated in accordance with Condition D, ELDRS
characterization. 0.9000/90% statistics are applied to the device parameters as specified in table I herein.
4.3.5.2 Radiation Lot Acceptance. Each wafer lot of active elements shall be evaluated for acceptance in accordance with
MIL-PRF-38534 and herein.
4.3.5.2.1 Total Ionizing Dose. Samples from every wafer lot will be assembled into packages and tested for wafer lot
acceptance Radiation Lot Acceptance Testing (RLAT). Five biased and five unbiased devices are tested in accordance with
condition A, of method 1019 of MIL-STD-883 to 200 krad(Si). 0.9000/90% statistics are applied to the device parameters as
specified in table I herein.
4.3.5.2.2 Technologies not tested. All active components in these devices are RHA tested.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09201
A
REVISION LEVEL
D
SHEET
24
5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38534.
6. NOTES
6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications
(original equipment), design applications, and logistics purposes.
6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractorprepared specification or drawing.
6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated as specified in
MIL-PRF-38534.
6.4 Record of users. Military and industrial users shall inform DLA Land and Maritime when a system application requires
configuration control and the applicable SMD to that system. DLA Land and Maritime will maintain a record of users and this list
will be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic devices
(FSC 5962) should contact DLA Land and Maritime-VA, telephone (614) 692-8108.
6.5 Comments. Comments on this drawing should be directed to DLA Land and Maritime-VA, Columbus, Ohio 43218-3990,
or telephone (614) 692-1081.
6.6 Sources of supply. Sources of supply are listed in MIL-HDBK-103 and QML-38534. The vendors listed in MIL-HDBK-103
and QML-38534 have submitted a certificate of compliance (see 3.7 herein) to DLA Land and Maritime-VA and have agreed to
this drawing.
STANDARD
MICROCIRCUIT DRAWING
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-09201
A
REVISION LEVEL
D
SHEET
25
STANDARD MICROCIRCUIT DRAWING BULLETIN
DATE: 13-10-15
Approved sources of supply for SMD 5962-09201 are listed below for immediate acquisition information only and
shall be added to MIL-HDBK-103 and QML-38534 during the next revisions. MIL-HDBK-103 and QML-38534 will be
revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a
certificate of compliance has been submitted to and accepted by DLA Land and Maritime-VA. This information
bulletin is superseded by the next dated revisions of MIL-HDBK-103 and QML-38534. DLA Land and Maritime
maintains an online database of all current sources of supply at http://www.landandmaritime.dla.mil/Programs/Smcr/.
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
number
Vendor
similar
PIN 2/
5962-0920101KUA
5962R0920101KUA
5962-0920101KUC
5962R0920101KUC
5962-0920101KZA
5962R0920101KZA
5962-0920101KZC
5962R0920101KZC
88379
88379
88379
88379
88379
88379
88379
88379
VRG8651-201-2S
VRG8651-901-2S
VRG8651-201-1S
VRG8651-901-1S
VRG8652-201-2S
VRG8652-901-2S
VRG8652-201-1S
VRG8652-901-1S
5962-0920102KXA
5962R0920102KXA
5962-0920102KXC
5962R0920102KXC
5962-0920102KYA
5962R0920102KYA
5962-0920102KYC
5962R0920102KYC
5962-0920102KTC
5962R0920102KTC
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
VRG8657-201-2S
VRG8657-901-2S
VRG8657-201-1S
VRG8657-901-1S
VRG8658-201-2S
VRG8658-901-2S
VRG8658-201-1S
VRG8658-901-1S
VRG8658-202-1S
VRG8658-902-1S
1/ The lead finish shown for each PIN representing
a hermetic package is the most readily available
from the manufacturer listed for that part. If the
desired lead finish is not listed contact the Vendor
to determine its availability.
2/ Caution. Do not use this number for item
acquisition. Items acquired to this number may not
satisfy the performance requirements of this drawing.
Vendor CAGE
number
88379
Vendor name
and address
Aeroflex Plainview Incorporated,
(Aeroflex Microelectronics Solutions)
35 South Service Road
Plainview, NY 11803
The information contained herein is disseminated for convenience only and the
Government assumes no liability whatsoever for any inaccuracies in the
information bulletin.