15W AC-DC Power-Supply PAC15C ● ● ● ● ● ● ● PCB-mountable plastic case 85 … 264 VAC or 120 … 370 VDC universal input range Continuously short circuit protected Over voltage protected Isolation class II MTBF > 300000 hrs 3 years product warranty Model selection guide Output voltage Type PAC15C03S PAC15C05S PAC15C09S PAC15C12S PAC15C15S PAC15C24S PAC15C48S [VDC] 3.3 5.0 9.0 12 15 24 48 Output voltage tolerance [%] typ. ±2 ±2 ±2 ±2 ±2 ±2 ±2 Output current Output power [mA] max. 3300 2800 1600 1250 1000 625 320 [W] max. 9.9 15 15 15 15 15 15 Efficiency @ full load [%] typ. 73 76 78 80 80 84 85 Specification Input Voltage range Line frequency range Full load input current Inrush current Recommended fuse Isolation Isolation voltage (input to output) Leakage current Isolation resistance Output Voltage accuracy Line regulation Temperature coefficient Ripple & noise up to 20 MHz Output load stability@ load change 10 to 100% Minimum load Hold-up time Protection Short circuit Over current Over temperature Output over voltage protection (external TVS D1 see Fig.1) Over voltage protection 5 V output 9 V output 12 V & 15 V output 24 V output 48 V output General Switching frequency Reliability MTBF@25°C 85..264 VAC or 120..370 VDC Power derating see diagram 47…63 Hz 370 mA @ 115 VAC, typ. 220 mA @ 230 VAC, typ. 10 A typ. @ 115 VAC 20 A typ. @ 230 VAC 2 A / 250V slow blow EMC compliance EMI: Conducted & Radiation (EMC application circuit is required, see figure 2) ESD: Electrostatic discharge RS: field susceptibility EFT: Fast transients on mainsline 3000 VAC for 1 min. 0.3 mA typ. @ Vin 230 VAC 108 Ω Surge: External circuit is required to converter at inrush and fast transient test, refer to typical application! ±2% ± 0.5 % ± 0.02 % / °C 100 mV max. ±1% CS: not required 15 ms typ. @ 115 VAC 80 ms typ. @ 230 VAC Continuous, auto recovery 110 %, min. of full load 150 °C, max. PAC15C03S: < 7.5 VDC PAC15C05S: < 7.5 VDC PAC15C09S: < 12 VDC PAC15C12S: < 20 VDC PAC15C15S: < 20 VDC PAC15C24S: < 30 VDC 7.5 VDC max. 12 VDC max. 20 VDC max. 30 VDC max. 60 VDC max. PFM: Voltage dips, short and interruptions immunity Safety approvals Safety Environmental Operating temperature (ambient) Storage temperature Case temperature Power derating above 55°C and below 0°C Humidity Cooling Physical Dimensions, PCB version Weight Case material Wave soldering temperature Manual soldering temperature Hot swap CE: EN55011 (CISPR22), class B RE: EN55011 (CISPR22), class B IEC-, EN61000-4-2, air ± 8 kV, contact ± 6 kV, perf. Criteria B IEC-, EN61000-4-3, 10 V / m perf. Criteria A IEC-, EN61000-4-4, ± 4 kV, perf. Criteria B IEC, EN61000-4-5, ±2 kV / ± 4 kV, perf. Criteria B IEC-, EN61000-4-6, 10 Vrms, perf. Criteria A IEC-, EN61000-4-8, 10 A / m, perf. Criteria A IEC-, EN61000-4-11, 0 %...70 %, perf. Criteria B EN60950, UL60950 Class II -40 °C to 70 °C (with derating) -40 °C to +105 °C 90°C, max. 3.75 % per °C, see diagram 95 %, non-condensing Free-air convection 62 x 45 x 22.5 mm 80 g UL94V-0 rated 260 ± 5 °C, 10 s max., 1.5 mm distance min. from case 360 ± 10 °C, 5 s max., 1.5 mm distance min. from case Not permissible! 65 kHz typ. > 300000 h Page 1 of 4 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected] 15W AC-DC Power-Supply PAC15C Output ripple & noise measure circuit Conductor track Oscilloscope probe L AC AC line voltage DC C1 C2 Load 10µF 100nF N 25.4mm Typical application Figure 1 L F1 25.4mm PAC15C R1 L ϑ C1 -Vout -Vo N N Application circuit and example for ripple and noise reduction Figure 2 Rs F1 D1 +Vout V U L C2 +Vo PIF001A PAC15C L1 L Cy Cy V Cy U Cx +V out Rd +V out C1 Cy C2 D1 -V out -V out Rs N N PE Model PAC15C03S PAC15C05S PAC15C09S PAC15C12S PAC15C15S PAC15C24S PAC15C48S C1 Cer. [µF] 1 1 1 1 1 1 1 C2 El cap [µF] 330 330 120 120 120 68 33 F1 Slow blow fuse 2A / 250V~ 2A / 250V~ 2A / 250V~ 2A / 250V~ 2A / 250V~ 2A / 250V~ 2A / 250V~ R1 NTC type 5D-9 5D-9 5D-9 5D-9 5D-9 5D-9 5D-9 Rs Rd [Ω] 2 2 2 2 2 2 2 [MΩ] 1 1 1 1 1 1 1 V MOV type S14K350 S14K350 S14K350 S14K350 S14K350 S14K350 S14K350 D1 TVS type SMBJ7.0A SMBJ7.0A SMBJ12A SMBJ20A SMBJ20A SMBJ30A SMBJ64A Cy 400 V~ [nF] 1 1 1 1 1 1 1 Cx 250 V~ [µF] 0.1 0.1 0.1 0.1 0.1 0.1 0.1 L1 Common mode [mH] 10 … 30 10 … 30 10 … 30 10 … 30 10 … 30 10 … 30 10 … 30 PIF 001A is an integrated PHI-CON filter module which contains all components in the framed field of figure 2 Note: 1. Output filtering capacitor C1 is a ceramic capacitor, it is used to filter high frequency noise. C2 is an electrolytic capacitor. It is recommended to use high frequency and low impedance electrolytic capacitor. For capacitance and current of capacitor please refer to manufacture’s datasheet. Voltage derating of capacitor should be 80 % or above. TVS D1 is a recommended component to protect post-circuits, if converter fails. 2. The serial resistors Rs protect the device under surge. 3. Recommended fuse parameter for F1 are 2 A / 250 V slow blow. A external input NTC limited the inrush current. Recommended NTC is the type 5D-9, see figure 1. 4. For EMC performance “EN55011 Class A”, refer to figure 1. For EMC performance “EN55011 Class B”, refer to figure 2. Cx: X capacitor, recommended values 0.1 μF / 275 VAC; Cy: Y capacitor, recommended values 1 nF / 400 VAC; L1: Common mode choke, recommended inductance is about 10 mH – 30 mH. Page 2 of 4 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected] 15W AC-DC Power-Supply PAC15C Page 3 of 4 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected] 15W AC-DC Power-Supply PAC15C Dimensions Pin connection Pin 1 2 3 4 5 6 7 8 Pin configuration omitted AC input (N) AC input (L) - V output omitted omitted omitted + V output Unit: mm Pin diameter tolerance: ± 0.1 mm Pin length: >6 mm General tolerances: ± 0.5 mm EMC optimized circuit PCB layout Recommend wiring: conductor tracke width A > 3 mm, safety distance B >9 mm PHI-CON is a trademark of HY-LINE Holding GmbH. Only for professional use by professionals! Not for resale or distribution to the general public in any way! Read the instructions for use carefully before using! Life Support Policy: HY-LINE does not authorize the use of any of its products for use in life support devices or systems without the express written approval of an officer of the Company. Life support systems are devices which support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user. Rev: 11.14 f Page 4 of 4 Deutschland: Inselkammerstraße 10 D-82008 Unterhaching Tel.: 089 614 503-10 E-Mail: [email protected] Schweiz: Gründenstrasse 82 CH-8247 Flurlingen Tel.: 052 647 42 00 E-Mail: [email protected]