Download

2W SMD DC-DC Converter P2DS-Series
●
●
●
●
●
●
●
SMD Package
Single / Dual output
Regulated output voltage
Up to 1500 VDC isolation
MTBF > 1 Mio. hours at 25°C
-40...85°C operating temperature range
Efficiency up to 80 %
Model guide
Type
Input voltage range
Output voltage
[VDC]
[VDC]
min.
[mA]
9...18
9...18
9...18
9...18
9...18
18...36
18...36
18...36
18...36
18...36
3.3
5.0
9.0
12.0
15.0
3.3
5.0
9.0
12.0
15.0
9...18
9…18
9…18
18...36
18...36
18...36
±5.0
±12.0
±15.0
±5.0
±12.0
±15.0
Single output
P2DS123R3S
P2DS1205S
P2DS1209S
P2DS1212S
P2DS1215S
P2DS243R3S
P2DS2405S
P2DS2409S
P2DS2412S
P2DS2415S
Dual output
P2DS1205D
P2DS1212D
P2DS1215D
P2DS2405D
P2DS2412D
P2DS2415D
Output current
Efficiency typ.
Capacitive load max.
max.
[mA]
[%]
[µF]
50
40
22
16
13
50
40
22
16
13
500
400
222
167
133
500
400
222
167
133
70
74
76
78
79
72
76
78
80
80
2200
1000
680
470
330
2200
1000
680
470
330
±20
±8
±7
±20
±8
±7
±200
±83
±67
±200
±83
±67
74
78
78
74
78
78
2 x 680
2 x 330
2 x 220
2 x 680
2 x 330
2 x 220
Specifications
Input
Filter
Input / output:
DC-Isolation voltage tested for 60
sec. @ leakage < 1mA
Isolation Resistance @ 500 VDC
Capacitance
Output
Positive voltage tolerance
Negative voltage tolerance
Line regulation @ full input range
Load regulation @ 10…100 %
load change
Output voltage drift @
10 % to 100 % load change
Temperature coefficient
Short circuit protection
General
Switching frequency
Environmental
EMI CE, with external filter circuit
EMS, ESD
Capacitors
1.5 kVDC
Operating temperature (ambient)
Storage temperature
Case temperature
Case temperature rise at full load
Humidity
109 Ω, min.
85 pF, typ.
± 3 % max.
± 5 % max.
± 0.5 % max.
± 1 % max. @ single output
± 5 % max. @ dual output
0.03 % / °C, max., at full load
Continuous, automatic recovery
~ 100 kHz, 5 & 12 Vin Types
~ 500 kHz, 15 & 24 Vin Types
Cooling
Physical
Package material
Weight
Reliability, MTBF
(MIL-HDBK-217 @ 25 °C)
Absolute maximum ratings
Vin 12 V types
Vin 24 V types
Lead soldering temperature
1.5 mm distance from body
CISPR22 / EN55022 CLASS A
IEC-,EN61000-4-2,
contact ±8 kV perf.criteria B
-40 °C to +85 °C
-55 °C to +125 °C
95 °C, max.
15 °C
Up to 95 %,
non-condensing
Free-air convection
Epoxy resin (UL94-V0)
5.2 g
1 Mio. hours
-0.7 ~ 22 VDC, max. 1 s
-0.7 ~ 40 VDC, max. 1 s
300 °C max. 10 s
Requirement On Output Load
For a stable and efficiently function of the DC/DC-converter, the minimal load must be also considered in addition to maximum load.
Make sure, that the specified input voltage range is not exceeded and the minimum output load no less than 10 % load If the actual
load is less than the specified minimum load, the output ripple may increase extremely while its efficiency and reliability will reduce
greatly. If the actual output power is less 10 %, please add an appropriate resistor as extra loading, or contact our company for
other lower output power products.
Page 1 of 3
Deutschland:
Inselkammerstraße 10
D-82008 Unterhaching
Tel.: 089 614 503-10
E-Mail: [email protected]
Schweiz:
Gründenstrasse 82
CH-8247 Flurlingen
Tel.: 052 647 42 00
E-Mail: [email protected]
2W SMD DC-DC Converter P2DS-Series
Figure 1, Recommended circuits
Single output
Dual output
The P2DS series have been tested according to the following recommended testing circuit before leaving factory. This series should
be tested under load. (See Figure 1).
Table 1 External capacitor recommendation
Series
Cin
Cout
P2DS12xxS
100 µF
0.1µF / mA
P2DS24xxS
47 µF
0.1µF / mA
If you want to further decrease the input / output ripple, you can increase capacitance
properly or choose capacitors with low ESR. However, the capacitance of the output
filter capacitor must be proper. Too large capacitance caused a start up problem. For
every channel of output, provided the safe and reliable operation is ensured, the
greatest capacitance of its filter capacitor sees Table 1.
Input Current
When it is used in unregulated power supply, be sure that the fluctuating range of
the power supply and the rippled voltage do not exceed the module standard.
Input current of power supply should afford the flash startup current of this kind of
DC/DC module. (Figure 2)
General: Ip ≤ 1.4*Iin-max:
Page 2 of 3
Deutschland:
Inselkammerstraße 10
D-82008 Unterhaching
Tel.: 089 614 503-10
E-Mail: [email protected]
Schweiz:
Gründenstrasse 82
CH-8247 Flurlingen
Tel.: 052 647 42 00
E-Mail: [email protected]
2W SMD DC-DC Converter P2DS-Series
Dimensions & Footprint
Lead
1
7
8
9
10
16
Single
output
- Vinput
N.C.
N.C.
+ Voutput
- Voutput
+ Vinput
Dual
output
- Vinput
N.C.
Com. outp.
+ Voutput
- Voutput
+ Vinput
All untis in mm
Pin tolerances ±0.1 mm
General tolerances 0.25 mm
Tube side view
All untis in mm
General tolerances ±0.5 mm
Short tube length 220 mm, Qty 8 pcs
Long tube length 530 mm, Qty 21 pcs
PHI-CON is a trademark of HY-LINE power components.
Only for professional use by professionals! Not for resale or distribution to the general public in any way! Read the instructions
carefully before using!
Life Support Policy: HY-LINE does not authorize the use of any of its products for use in life support devices or systems without
the express written approval of an officer of the Company. Life support systems are devices which support or sustain life, and
whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably
expected to result in significant injury to the user. Rev: 02.14 f
Page 3 of 3
Deutschland:
Inselkammerstraße 10
D-82008 Unterhaching
Tel.: 089 614 503-10
E-Mail: [email protected]
Schweiz:
Gründenstrasse 82
CH-8247 Flurlingen
Tel.: 052 647 42 00
E-Mail: [email protected]