CYUSB301X, CYUSB201X EZ-USB FX3 SuperSpeed USB Controller Datasheet.pdf

CYUSB301X/CYUSB201X
EZ-USB® FX3: SuperSpeed USB Controller
Features
Applications
■
■
Digital video camcorders
■
Digital still cameras
■
Printers
■
Scanners
■
Video capture cards
■
Test and measurement equipment
■
Surveillance cameras
■
Personal navigation devices
■
Medical imsaging devices
■
Video IP phones
■
Portable media players
■
Industrial cameras
■
Data loggers
■
Data acquisition
■
High-performance Human Interface Devices (gesture
recognition)
■
■
■
Universal serial bus (USB) integration
❐ USB 3.1, Gen 1 and USB 2.0 peripherals compliant with USB
3.1 Specification Revision 1.0 (TID # 340800007)
❐ 5-Gbps SuperSpeed PHY compliant with USB 3.1 Gen 1
❐ High-speed On-The-Go (HS-OTG) host and peripheral
compliant with OTG Supplement Version 2.0
❐ Thirty-two physical endpoints
❐ Support for battery charging Specification 1.1 and accessory
charger adaptor (ACA) detection
General Programmable Interface (GPIF™ II)
❐ Programmable 100-MHz GPIF II enables connectivity to a
wide range of external devices
❐ 8-, 16-, 24-, and 32-bit data bus
❐ Up to16 configurable control signals
Fully accessible 32-bit CPU
❐ ARM926EJ core with 200-MHz operation
❐ 512-KB or 256-KB embedded SRAM
Additional connectivity to the following peripherals
❐ SPI master at up to 33 MHz
❐ UART support of up to 4 Mbps
2
❐ I C master controller at 1 MHz
2
❐ I S master (transmitter only) at sampling frequencies of
32 kHz, 44.1 kHz, and 48 kHz
■
Selectable clock input frequencies
❐ 19.2, 26, 38.4, and 52 MHz
❐ 19.2-MHz crystal input support
■
Ultra low-power in core power-down mode
❐ Less than 60 µA with VBATT on and 20 µA with VBATT off
■
Independent power domains for core and I/O
❐ Core operation at 1.2 V
❐ I2S, UART, and SPI operation at 1.8 to 3.3 V
2
❐ I C operation at 1.2 V to 3.3 V
■
Package options
❐ 121-ball, 10- × 10-mm, 0.8-mm pitch Pb-free ball grid array
(BGA)
❐ 131-ball, 4.7- × 5.1-mm, 0.4-mm pitch wafer-level chip scale
package (WLCSP)
❐ See Table 20 for details on the eight FX3 variants
■
EZ-USB® Software Development Kit (SDK) for code development of firmware and PC Applications
❐ Includes RTOS Framework (using ThreadX Version 5)
❐ Firmware examples covering all I/O modules
❐ Visual Studio host examples using C++ and C#
■
SuperSpeed Explorer Board available for rapid prototyping
❐ Several accessory boards also available:
• Adapter boards for Xilinx/Altera FPGA development
• Adapter board for Video development
• CPLD board for concept testing and initial development
Cypress Semiconductor Corporation
Document Number: 001-52136 Rev. *S
•
For a complete list of related documentation, click here.
198 Champion Court
•
San Jose, CA 95134-1709
• 408-943-2600
Revised April 7, 2016
CYUSB301X/CYUSB201X
Logic Block Diagram
Document Number: 001-52136 Rev. *S
Page 2 of 53
CYUSB301X/CYUSB201X
More Information
Cypress provides a wealth of data at www.cypress.com to help you to select the right <product> device for your design, and to help
you to quickly and effectively integrate the device into your design. For a comprehensive list of resources, see the knowledge base
article KBA87889, How to design with FX3/FX3S.
■
■
■
Overview: USB Portfolio, USB Roadmap
USB 3.0 Product Selectors: FX3, FX3S, CX3, HX3, West
Bridge Benicia
Application notes: Cypress offers a large number of USB application notes covering a broad range of topics, from basic to
advanced level. Recommended application notes for getting
started with FX3 are:
❐ AN75705 - Getting Started with EZ-USB FX3
❐ AN76405 - EZ-USB FX3 Boot Options
❐ AN70707 - EZ-USB FX3/FX3S Hardware Design Guidelines
and Schematic Checklist
❐ AN65974 - Designing with the EZ-USB FX3 Slave FIFO Interface
❐ AN75779 - How to Implement an Image Sensor Interface with
EZ-USB FX3 in a USB Video Class (UVC) Framework
❐ AN86947 - Optimizing USB 3.0 Throughput with EZ-USB
FX3
❐ AN84868 - Configuring an FPGA over USB Using Cypress
EZ-USB FX3
❐ AN68829 - Slave FIFO Interface for EZ-USB FX3: 5-Bit Address Mode
❐
AN73609 - EZ-USB FX2LP/ FX3 Developing Bulk-Loop Example on Linux
❐ AN77960 - Introduction to EZ-USB FX3 High-Speed USB
Host Controller
❐ AN76348 - Differences in Implementation of EZ-USB FX2LP
and EZ-USB FX3 Applications
❐ AN89661 - USB RAID 1 Disk Design Using EZ-USB FX3S
■
Code Examples: < Modify as required >
❐ USB Hi-Speed
❐ USB Full-Speed
❐ USB SuperSpeed
■
Technical Reference Manual (TRM):
❐ EZ-USB FX3 Technical Reference Manual
■
Development Kits:
❐ CYUSB3KIT-003, EZ-USB FX3 SuperSpeed Explorer Kit
❐ CYUSB3KIT-001, EZ-USB FX3 Development Kit
■
Models: IBIS
EZ-USB FX3 Software Development Kit
Cypress delivers the complete software and firmware stack for FX3, in order to easily integrate SuperSpeed USB into any embedded
application. The Software Development Kit (SDK) comes with tools, drivers and application examples, which help accelerate application development.
GPIF™ II Designer
The GPIF II Designer is a graphical software that allows designers to configure the GPIF II interface of the EZ-USB FX3 USB 3.0
Device Controller.
The tool allows users the ability to select from one of five Cypress supplied interfaces, or choose to create their own GPIF II interface
from scratch. Cypress has supplied industry standard interfaces such as Asynchronous and Synchronous Slave FIFO, Asynchronous
and Synchronous SRAM, and Asynchronous SRAM. Designers who already have one of these pre-defined interfaces in their system
can simply select the interface of choice, choose from a set of standard parameters such as bus width (x8, 16, x32) endianess, clock
settings, and compile the interface. The tool has a streamlined three step GPIF interface development process for users who need a
customized interface. Users are able to first select their pin configuration and standard parameters. Secondly, they can design a virtual
state machine using configurable actions. Finally, users can view output timing to verify that it matches the expected timing. Once the
three step process is complete, the interface can be compiled and integrated with FX3.
Document Number: 001-52136 Rev. *S
Page 3 of 53
CYUSB301X/CYUSB201X
Contents
Functional Overview .......................................................... 5
Application Examples .................................................... 5
USB Interface ...................................................................... 6
OTG............................................................................... 6
ReNumeration ............................................................... 7
EZ-Dtect ........................................................................ 7
VBUS Overvoltage Protection ....................................... 7
Carkit UART Mode ........................................................ 7
GPIF II .................................................................................. 8
CPU ...................................................................................... 8
JTAG Interface .................................................................... 8
Other Interfaces .................................................................. 8
SPI Interface.................................................................. 8
UART Interface.............................................................. 9
I2C Interface.................................................................. 9
I2S Interface .................................................................. 9
Boot Options....................................................................... 9
Reset.................................................................................... 9
Hard Reset .................................................................... 9
Soft Reset...................................................................... 9
Clocking ............................................................................ 10
32-kHz Watchdog Timer Clock Input........................... 10
Power................................................................................. 11
Power Modes .............................................................. 11
Digital I/Os......................................................................... 13
GPIOs................................................................................. 13
System-level ESD ............................................................. 13
Pin Configurations ........................................................... 14
Document Number: 001-52136 Rev. *S
Pin Description ................................................................. 15
Electrical Specifications .................................................. 19
Absolute Maximum Ratings......................................... 19
Operating Conditions................................................... 19
DC Specifications ........................................................ 19
AC Timing Parameters .....................................................21
GPIF II Timing ............................................................. 21
Slave FIFO Interface ................................................... 24
Host Processor Interface (P-Port) Timing ................... 30
Serial Peripherals Timing ............................................ 37
Reset Sequence.......................................................... 42
Package Diagram.............................................................. 43
Ordering Information........................................................ 45
Ordering Code Definitions ........................................... 45
Acronyms .......................................................................... 46
Document Conventions ................................................... 46
Units of Measure ......................................................... 46
Errata ................................................................................. 47
Qualification Status ..................................................... 47
Errata Summary .......................................................... 47
Document History Page ................................................... 50
Sales, Solutions, and Legal Information ........................ 53
Worldwide Sales and Design Support......................... 53
Products ...................................................................... 53
PSoC®Solutions ......................................................... 53
Cypress Developer Community................................... 53
Technical Support ....................................................... 53
Page 4 of 53
CYUSB301X/CYUSB201X
Functional Overview
Cypress’s EZ-USB FX3 is a SuperSpeed peripheral controller,
providing integrated and flexible features.
FX3 has a fully configurable, parallel, general programmable
interface called GPIF II, which can connect to any processor,
ASIC, or FPGA. GPIF II is an enhanced version of the GPIF in
FX2LP, Cypress’s flagship USB 2.0 product. It provides easy and
glueless connectivity to popular interfaces, such as
asynchronous SRAM, asynchronous and synchronous address
data multiplexed interfaces, and parallel ATA.
FX3 has integrated the USB 3.1 Gen 1 and USB 2.0 physical
layers (PHYs) along with a 32-bit ARM926EJ-S microprocessor
for powerful data processing and for building custom
applications. It implements an architecture that enables
375-MBps data transfer from GPIF II to the USB interface.
An integrated USB 2.0 OTG controller enables applications in
which FX3 may serve dual roles; for example, EZ-USB FX3 may
function as an OTG Host to MSC as well as HID-class devices.
FX3 contains 512 KB or 256 KB of on-chip SRAM (see Ordering
Information on page 45) for code and data. EZ-USB FX3 also
provides interfaces to connect to serial peripherals such as
UART, SPI, I2C, and I2S.
FX3 comes with application development tools. The software
development kit comes with firmware and host application
examples for accelerating time to market.
FX3 complies with the USB 3.1, Gen 1.0 specification and is also
backward compatible with USB 2.0. It also complies with the
Battery Charging Specification v1.1 and USB 2.0 OTG
Specification v2.0.
Application Examples
In a typical application (see Figure 1), the FX3 functions as the
main processor running the application software that connects
external hardware to the SuperSpeed USB connection.
Additionally, FX3 can function as a coprocessor connecting via
the GPIF II interface to an application processor (see Figure 2)
and operates as a subsystem providing SuperSpeed USB
connectivity to the application processor.
Figure 1. EZ-USB FX3 as Main Processor
Crystal*
Clock
USB
Host
USB
Ez-USB FX3
GPIF II
External Slave
Device
(e.g. Image
Sensor)
I 2C
* A clock input may be provided on the
CLKIN pin instead of a crystal input
Document Number: 001-52136 Rev. *S
EEPROM
Page 5 of 53
CYUSB301X/CYUSB201X
Figure 2. EZ-USB FX3 as a Coprocessor
Crystal*
Clock
USB
Host
USB
Ez-USB FX3
GPIF II
External Master
(e.g. MCU/CPU/
FPGA/ASIC)
I 2C
* A clock input may be provided on the
CLKIN pin instead of a crystal input
EEPROM
USB Interface
OTG
FX3 complies with the following specifications and supports the
following features:
FX3 is compliant with the OTG Specification Revision 2.0. In
OTG mode, FX3 supports both A and B device modes and
supports Control, Interrupt, Bulk, and Isochronous data
transfers.
■
Supports USB peripheral functionality compliant with USB 3.1
Specification Revision 1.0 and is also backward compatible
with the USB 2.0 Specification.
■
FX3 Hi-Speed parts (CYUSB201X) only support USB 2.0.
■
Complies with OTG Supplement Revision 2.0. It supports
High-Speed, Full-Speed, and Low-Speed OTG dual-role device
capability. As a peripheral, FX3 is capable of SuperSpeed,
High-Speed, and Full-Speed. As a host, it is capable of
High-Speed, Full-Speed, and Low-Speed.
■
Supports Carkit Pass-Through UART functionality on USB
D+/D– lines based on the CEA-936A specification.
■
Supports 16 IN and 16 OUT endpoints.
■
Supports the USB 3.0 Streams feature. It also supports USB
Attached SCSI (UAS) device-class to optimize mass-storage
access performance.
■
■
As a USB peripheral, application examples show that the FX3
supports UAS, USB Video Class (UVC), and Mass Storage
Class (MSC) USB peripheral classes. All other device classes
can be supported by customer firmware; a template example
is provided as a starting point.
FX3 requires an external charge pump (either standalone or
integrated into a PMIC) to power VBUS in the OTG A-device
mode.
The Target Peripheral List for OTG host implementation consists
of MSC- and HID-class devices.
FX3 does not support Attach Detection Protocol (ADP).
OTG Connectivity
In OTG mode, FX3 can be configured to be an A, B, or dual-role
device. It can connect to the following:
■
ACA device
■
Targeted USB peripheral
■
SRP-capable USB peripheral
■
HNP-capable USB peripheral
■
OTG host
■
HNP-capable host
■
OTG device
As an OTG host, application examples show that FX3 supports
MSC and HID device classes.
Note When the USB port is not in use, disable the PHY and
transceiver to save power.
Document Number: 001-52136 Rev. *S
Page 6 of 53
CYUSB301X/CYUSB201X
ReNumeration
Figure 3. System Diagram with OVP Device For VBUS
Because of FX3's soft configuration, one chip can take on the
identities of multiple distinct USB devices.
VIO5
AVDD
VDD
CVDDQ
VIO3
VIO4
VIO2
VBUS
OTG_ID
OVP device
USB Connector
2
SSRXSSRX+
SSTXSSTX+
DD+
3
4
5
6
7
8
9
USB-Port
EZ-Dtect
FX3 can detect the following resistance ranges:
VIO1
U3RXVDDQ
EZ-USB FX3
1
FX3 supports USB Charger and accessory detection (EZ-Dtect).
The charger detection mechanism complies with the Battery
Charging Specification Revision 1.1. In addition to supporting
this version of the specification, FX3 also provides hardware
support to detect the resistance values on the ID pin.
U3TXVDDQ
POWER SUBSYSTEM
When first plugged into USB, FX3 enumerates automatically with
the Cypress Vendor ID (0x04B4) and downloads firmware and
USB descriptors over the USB interface. The downloaded
firmware executes an electrical disconnect and connect. FX3
enumerates again, this time as a device defined by the
downloaded information. This patented two-step process, called
ReNumeration, happens instantly when the device is plugged in.
GND
■
Less than 10 
■
Less than 1 k
Carkit UART Mode
■
65 k to 72 k
■
35 kto 39 k
The USB interface supports the Carkit UART mode (UART over
D+/D–) for non-USB serial data transfer. This mode is based on
the CEA-936A specification.
■
99.96 k to 104.4 k (102 k2%)
■
119 k to 132 k
■
Higher than 220 k
■
431.2 k to 448.8 k (440 k2%)
In the Carkit UART mode, the output signaling voltage is 3.3 V.
When configured for the Carkit UART mode, TXD of UART
(output) is mapped to the D– line, and RXD of UART (input) is
mapped to the D+ line.
FX3's charger detects a dedicated wall charger, Host/Hub
charger, and Host/Hub.
VBUS Overvoltage Protection
The maximum input voltage on FX3's VBUS pin is 6 V. A charger
can supply up to 9 V on VBUS. In this case, an external
overvoltage protection (OVP) device is required to protect FX3
from damage on VBUS. Figure 3 shows the system application
diagram with an OVP device connected on VBUS. Refer to
Table 8 for the operating range of VBUS and VBATT.
In the Carkit UART mode, FX3 disables the USB transceiver and
D+ and D– pins serve as pass-through pins to connect to the
UART of the host processor. The Carkit UART signals may be
routed to the GPIF II interface or to GPIO[48] and GPIO[49], as
shown in Figure on page 8.
In this mode, FX3 supports a rate of up to 9600 bps.
Figure 4. Carkit UART Pass-through Block Diagram
Ctrl
Carkit UART Pass-through
UART_ TXD
TXD
UART_ RXD
RXD
RXD (DP)
Carkit UART Pass-through
Interface on GPIOs
Document Number: 001-52136 Rev. *S
USB PHY DM
MUX
DP
GPIO[48]
(UART_ TX)
USB-Port
(
)
Carkit UART Pass-through
Interface on GPIF II
TXD (DM)
GPIO[49]
( UART_ RX)
Page 7 of 53
CYUSB301X/CYUSB201X
GPIF II
CPU
The high-performance GPIF II interface enables functionality
similar to, but more advanced than, FX2LP’s GPIF and Slave
FIFO interfaces.
FX3 has an on-chip 32-bit, 200-MHz ARM926EJ-S core CPU.
The core has direct access to 16 KB of Instruction Tightly
Coupled Memory (TCM) and 8 KB of Data TCM. The
ARM926EJ-S core provides a JTAG interface for firmware
debugging.
The GPIF II is a programmable state machine that enables a
flexible interface that may function either as a master or slave in
industry-standard or proprietary interfaces. Both parallel and
serial interfaces may be implemented with GPIF II.
Here is a list of GPIF II features:
■
Functions as master or slave
■
Provides 256 firmware programmable states
■
Supports 8-bit, 16-bit, 24-bit, and 32-bit parallel data bus
■
Enables interface frequencies up to 100 MHz
■
Supports 14 configurable control pins when a 32- bit data bus
is used. All control pins can be either input/output or bidirectional.
■
Supports 16 configurable control pins when a 16/8 data bus is
used. All control pins can be either input/output or bi-directional.
GPIF II state transitions are based on control input signals. The
control output signals are driven as a result of the GPIF II state
transitions. The INT# output signal can be controlled by GPIF II.
Refer to the GPIFII Designer tool. The GPIF II state machine’s
behavior is defined by a GPIF II descriptor. The GPIF II
descriptor is designed such that the required interface specifications are met. 8 KB of memory (separate from the 256/512 KB of
embedded SRAM) is dedicated to the GPIF II waveform where
the GPIF II descriptor is stored in a specific format.
Cypress’s GPIFII Designer Tool enables fast development of
GPIF II descriptors and includes examples for common
interfaces.
Example implementations of GPIF II are the asynchronous slave
FIFO and synchronous slave FIFO interfaces.
Slave FIFO interface
The Slave FIFO interface signals are shown in Figure 5. This
interface allows an external processor to directly access up to
four buffers internal to FX3. Further details of the Slave FIFO
interface are described on page 24.
Note Access to all 32 buffers is also supported over the slave
FIFO interface. For details, contact Cypress Applications
Support.
Figure 5. Slave FIFO Interface
P KTEND
FLAG B
FLAG A
A [1:0]
D[31:0]
■
Integrates 256/512 KB of embedded SRAM for code and data
and 8 KB of Instruction cache and Data cache.
■
Implements efficient and flexible DMA connectivity between the
various peripherals (such as, USB, GPIF II, I2S, SPI, UART,
I2C), requiring firmware only to configure data accesses
between peripherals, which are then managed by the DMA
fabric.
■
Allows easy application development using industry-standard
development tools for ARM926EJ-S.
Examples of the FX3 firmware are available with the Cypress
EZ-USB FX3 Development Kit.
JTAG Interface
FX3’s JTAG interface has a standard five-pin interface to connect
to a JTAG debugger in order to debug firmware through the
CPU-core's on-chip-debug circuitry.
Industry-standard debugging tools for the ARM926EJ-S core
can be used for the FX3 application development.
Other Interfaces
FX3 supports the following serial peripherals:
■
SPI
■
UART
■
I2C
■
I2S
The SPI, UART, and I2S interfaces are multiplexed on the serial
peripheral port.
The CYUSB3012 and CYUSB3014 Pin List on page 15 shows
details of how these interfaces are multiplexed. Note that when
GPIF II is configured for a 32-bit data bus width (CYUSB3012
and CYUSB3014), then the SPI interface is not available.
SPI Interface
FX3 supports an SPI Master interface on the Serial Peripherals
port. The maximum operation frequency is 33 MHz.
S LCS#
External M aster
(For exam ple,
M C U/C PU/
FPG A/ASIC )
FX3 offers the following advantages:
EZ-U SB FX3
The SPI controller supports four modes of SPI communication
(see SPI Timing Specification on page 40 for details on the
modes) with the Start-Stop clock. This controller is a
single-master controller with a single automated SSN control. It
supports transaction sizes ranging from four bits to 32 bits.
S LW R#
SLRD#
S LO E#
Note: M ultiple Flags m ay be configured.
Document Number: 001-52136 Rev. *S
Page 8 of 53
CYUSB301X/CYUSB201X
Boot Options
UART Interface
The UART interface of FX3 supports full-duplex communication.
It includes the signals noted in Table 1.
Table 1. UART Interface Signals
Signal
TX
RX
CTS
RTS
Description
Output signal
Input signal
Flow control
Flow control
The UART is capable of generating a range of baud rates, from
300 bps to 4608 Kbps, selectable by the firmware. If flow control
is enabled, then FX3's UART only transmits data when the CTS
input is asserted. In addition to this, FX3’s UART asserts the RTS
output signal, when it is ready to receive data.
FX3 can load boot images from various sources, selected by the
configuration of the PMODE pins. Following are the FX3 boot
options:
■
Boot from USB
■
Boot from I2C
■
Boot from SPI (SPI devices supported are M25P32 (32 Mbit),
M25P16 (16 Mbit), M25P80 (8 Mbit), and M25P40 (4 Mbit)) or
their equivalents
■
Boot from GPIF II ASync ADMux mode
■
Boot from GPIF II Sync ADMux mode
■
Boot from GPIF II ASync SRAM mode
Table 2. FX3 Booting Options
2
PMODE[2:0][1]
F00
F01
F11
F0F
F1F
1FF
0F1
I C Interface
I2C
I2C
FX3’s
interface is compatible with the
Bus Specification
Revision 3. This I2C interface is capable of operating only as I2C
master; therefore, it may be used to communicate with other I2C
slave devices. For example, FX3 may boot from an EEPROM
connected to the I2C interface, as a selectable boot option.
FX3’s I2C Master Controller also supports multi-master mode
functionality.
The power supply for the I2C interface is VIO5, which is a
separate power domain from the other serial peripherals. This
gives the I2C interface the flexibility to operate at a different
voltage than the other serial interfaces.
The I2C controller supports bus frequencies of 100 kHz,
400 kHz, and 1 MHz. When VIO5 is 1.2 V, the maximum
operating frequency supported is 100 kHz. When VIO5 is 1.8 V,
2.5 V, or 3.3 V, the operating frequencies supported are 400 kHz
and 1 MHz. The I2C controller supports clock-stretching to
enable slower devices to exercise flow control.
Boot From
Sync ADMux (16-bit)
Async ADMux (16-bit)
USB boot
Async SRAM (16-bit)
I2C, On Failure, USB Boot is Enabled
I2C only
SPI, On Failure, USB Boot is Enabled
Reset
Hard Reset
The I2C interface’s SCL and SDA signals require external pull-up
resistors. The pull-up resistors must be connected to VIO5.
A hard reset is initiated by asserting the Reset# pin on FX3. The
specific reset sequence and timing requirements are detailed in
Figure 30 on page 42 and Table 19 on page 42. All I/Os are
tristated during a hard reset. Note however, that the on-chip
bootloader has control after a hard reset and it will configure I/O
signals depending on the selected boot mode; see AN76405 EZ-USB® FX3™ Boot Options for more details.
I2S Interface
Soft Reset
FX3 has an I2S port to support external audio codec devices.
FX3 functions as I2S Master as transmitter only. The I2S interface
consists of four signals: clock line (I2S_CLK), serial data line
(I2S_SD), word select line (I2S_WS), and master system clock
(I2S_MCLK). FX3 can generate the system clock as an output
on I2S_MCLK or accept an external system clock input on
I2S_MCLK.
In a soft reset, the processor sets the appropriate bits in the
PP_INIT control register. There are two types of Soft Reset:
The sampling frequencies supported by the I2S interface are
32 kHz, 44.1 kHz, and 48 kHz.
■
CPU Reset – The CPU Program Counter is reset. Firmware
does not need to be reloaded following a CPU Reset.
■
Whole Device Reset – This reset is identical to Hard Reset.
■
The firmware must be reloaded following a Whole Device
Reset.
Note
1. F indicates Floating.
Document Number: 001-52136 Rev. *S
Page 9 of 53
CYUSB301X/CYUSB201X
Clocking
Clock inputs to FX3 must meet the phase noise and jitter requirements specified in Table 4 on page 10.
FX3 allows either a crystal to be connected between the XTALIN
and XTALOUT pins or an external clock to be connected at the
CLKIN pin. The XTALIN, XTALOUT, CLKIN, and CLKIN_32 pins
can be left unconnected if they are not used.
The input clock frequency is independent of the clock and data
rate of the FX3 core or any of the device interfaces. The internal
PLL applies the appropriate clock multiply option depending on
the input frequency.
Crystal frequency supported is 19.2 MHz, while the external
clock frequencies supported are 19.2, 26, 38.4, and 52 MHz.
Table 3. Crystal/Clock Frequency Selection
FX3 has an on-chip oscillator circuit that uses an external
19.2-MHz (±100 ppm) crystal (when the crystal option is used).
An appropriate load capacitance is required with a crystal. Refer
to the specification of the crystal used to determine the appropriate load capacitance. The FSLC[2:0] pins must be configured
appropriately to select the crystal- or clock-frequency option. The
configuration options are shown in Table 3.
FSLC[2]
FSLC[1]
FSLC[0]
0
1
1
1
1
0
0
0
1
1
0
0
1
0
1
Crystal/Clock
Frequency
19.2-MHz crystal
19.2-MHz input CLK
26-MHz input CLK
38.4-MHz input CLK
52-MHz input CLK
Table 4. FX3 Input Clock Specifications
Parameter
Phase noise
Description
100-Hz offset
1-kHz offset
10-kHz offset
100-kHz offset
1-MHz offset
Maximum frequency deviation
Duty cycle
Overshoot
Undershoot
Rise time/fall time
–
–
–
–
–
Specification
Min
–
–
–
–
–
–
30
–
–
–
Units
Max
–75
–104
–120
–128
–130
150
70
3
–3
3
dB
ppm
%
ns
32-kHz Watchdog Timer Clock Input
FX3 includes a watchdog timer. The watchdog timer can be used to interrupt the ARM926EJ-S core, automatically wake up the FX3
in Standby mode, and reset the ARM926EJ-S core. The watchdog timer runs a 32-kHz clock, which may be optionally supplied from
an external source on a dedicated FX3 pin.
The firmware can disable the watchdog timer. Requirements for the optional 32-kHz clock input are listed in Table 5.
Table 5. 32-kHz Clock Input Requirements
Min
Max
Units
Duty cycle
Parameter
40
60
%
Frequency deviation
–
±200
ppm
Rise time/fall time
–
200
ns
Document Number: 001-52136 Rev. *S
Page 10 of 53
CYUSB301X/CYUSB201X
Power
■
FX3 has the following power supply domains:
■
IO_VDDQ: This is a group of independent supply domains for
digital I/Os. The voltage level on these supplies is 1.8 V to 3.3 V.
FX3 provides six independent supply domains for digital I/Os
listed as follows (see Table 7 on page 15 for details on each of
the power domain signals):
❐ VIO1: GPIF II I/O
❐ VIO2: IO2
❐ VIO3: IO3
2
❐ VIO4: UART-/SPI/I S
2
❐ VIO5: I C and JTAG (supports 1.2 V to 3.3 V)
❐ CVDDQ: This is the supply voltage for clock and reset I/O. It
should be either 1.8 V or 3.3 V based on the voltage level of
the CLKIN signal.
❐ VDD: This is the supply voltage for the logic core. The nominal
supply-voltage level is 1.2 V. This supplies the core logic
circuits. The same supply must also be used for the following:
• AVDD: This is the 1.2-V supply for the PLL, crystal oscillator, and other core analog circuits
• U3TXVDDQ/U3RXVDDQ: These are the 1.2-V supply voltages for the USB 3.0 interface.
VBATT/VBUS: This is the 3.2-V to 6-V battery power supply
for the USB I/O and analog circuits. This supply powers the
USB transceiver through FX3's internal voltage regulator.
VBATT is internally regulated to 3.3 V.
Power Modes
FX3 supports the following power modes:
■
Normal mode: This is the full-functional operating mode. The
internal CPU clock and the internal PLLs are enabled in this
mode.
❐ Normal operating power consumption does not exceed the
sum of ICC Core max and ICC USB max (see Table 7 on page
15 for current consumption specifications).
❐ The I/O power supplies VIO2, VIO3, VIO4, and VIO5 can be
turned off when the corresponding interface is not in use.
VIO1 cannot be turned off at any time if the GPIF II interface
is used in the application.
■
Low-power modes (see Table 6 on page 11):
❐ Suspend mode with USB 3.0 PHY enabled (L1)
❐ Suspend mode with USB 3.0 PHY disabled (L2)
❐ Standby mode (L3)
❐ Core power-down mode (L4)
Table 6. Entry and Exit Methods for Low-Power Modes
Low-Power Mode
Suspend Mode with
USB 3.0 PHY
Enabled (L1)
Characteristics
■
The power consumption in this mode does
not exceed ISB1
■
USB 3.0 PHY is enabled and is in U3 mode
(one of the suspend modes defined by the
USB 3.0 specification). This one block
alone is operational with its internal clock
while all other clocks are shut down
■
All I/Os maintain their previous state
■
Power supply for the wakeup source and
core power must be retained. All other
power domains can be turned on/off
individually
■
■
■
The states of the configuration registers,
buffer memory, and all internal RAM are
maintained
All transactions must be completed before
FX3 enters Suspend mode (state of
outstanding transactions are not
preserved)
Methods of Entry
■
■
Firmware executing on
ARM926EJ-S core can put FX3 into
suspend mode. For example, on
USB suspend condition, firmware
may decide to put FX3 into suspend
mode
External Processor, through the use
of mailbox registers, can put FX3 into
suspend mode
Methods of Exit
■
D+ transitioning to low
or high
■
D- transitioning to low
or high
■
Impedance change on
OTG_ID pin
■
Resume condition on
SSRX±
■
Detection of VBUS
■
Level detect on
UART_CTS
(programmable
polarity)
■
GPIF II interface
assertion of CTL[0]
■
Assertion of RESET#
The firmware resumes operation from
where it was suspended (except when
woken up by RESET# assertion) because
the program counter does not reset
Document Number: 001-52136 Rev. *S
Page 11 of 53
CYUSB301X/CYUSB201X
Table 6. Entry and Exit Methods for Low-Power Modes (continued)
Low-Power Mode
Suspend Mode with
USB 3.0 PHY
Disabled (L2)
Standby Mode (L3)
Characteristics
■
The power consumption in this mode does
not exceed ISB2
■
USB 3.0 PHY is disabled and the USB
interface is in suspend mode
■
The clocks are shut off. The PLLs are
disabled
■
All I/Os maintain their previous state
■
USB interface maintains the previous
state
Methods of Entry
■
■
Firmware executing on
ARM926EJ-S core can put FX3 into
suspend mode. For example, on
USB suspend condition, firmware
may decide to put FX3 into suspend
mode
External Processor, through the use
of mailbox registers can put FX3 into
suspend mode
Methods of Exit
■
D+ transitioning to low
or high
■
D- transitioning to low
or high
■
Impedance change on
OTG_ID pin
■
Resume condition on
SSRX±
■
Detection of VBUS
■
Power supply for the wakeup source and
core power must be retained. All other
power domains can be turned on/off
individually
■
Level detect on
UART_CTS
(programmable
polarity)
■
The states of the configuration registers,
buffer memory and all internal RAM are
maintained
■
GPIF II interface
assertion of CTL[0]
■
Assertion of RESET#
■
All transactions must be completed before
FX3 enters Suspend mode (state of
outstanding transactions are not
preserved)
■
The firmware resumes operation from
where it was suspended (except when
woken up by RESET# assertion) because
the program counter does not reset
■
The power consumption in this mode does
not exceed ISB3
■
Detection of VBUS
■
■
All configuration register settings and
program/data RAM contents are
preserved. However, data in the buffers or
other parts of the data path, if any, is not
guaranteed. Therefore, the external
processor should take care that the data
needed is read before putting FX3 into this
Standby Mode
Level detect on
UART_CTS
(Programmable
Polarity)
■
GPIF II interface
assertion of CTL[0]
■
Assertion of RESET#
■
The program counter is reset after waking
up from Standby
■
GPIO pins maintain their configuration
■
Crystal oscillator is turned off
■
Internal PLL is turned off
■
USB transceiver is turned off
■
ARM926EJ-S core is powered down.
Upon wakeup, the core re-starts and runs
the program stored in the program/data
RAM
■
Power supply for the wakeup source and
core power must be retained. All other
power domains can be turned on/off
individually
Document Number: 001-52136 Rev. *S
■
Firmware executing on
ARM926EJ-S core or external
processor configures the appropriate
register
Page 12 of 53
CYUSB301X/CYUSB201X
Table 6. Entry and Exit Methods for Low-Power Modes (continued)
Low-Power Mode
Core Power Down
Mode (L4)
Characteristics
■
The power consumption in this mode does
not exceed ISB4
■
Core power is turned off
■
All buffer memory, configuration registers,
and the program RAM do not maintain
state. After exiting this mode, reload the
firmware
■
In this mode, all other power domains can
be turned on/off individually
Methods of Entry
■
Turn off VDD
Methods of Exit
■
Reapply VDD
■
Assertion of RESET#
Digital I/Os
EMI
FX3 has internal firmware-controlled pull-up or pull-down
resistors on all digital I/O pins. An internal 50-k resistor pulls
the pins high, while an internal 10-k resistor pulls the pins low
to prevent them from floating. The I/O pins may have the
following states:
FX3 meets EMI requirements outlined by FCC 15B (USA) and
EN55022 (Europe) for consumer electronics. FX3 can tolerate
EMI, conducted by the aggressor, outlined by these specifications and continue to function as expected.
System-level ESD
■
Tristated (High-Z)
■
Weak pull-up (via internal 50 k)
■
Pull-down (via internal 10 k)
FX3 has built-in ESD protection on the D+, D–, and GND pins on
the USB interface. The ESD protection levels provided on these
ports are:
■
Hold (I/O hold its value) when in low-power modes
■
■
The JTAG TDI, TMS, and TRST# signals have fixed 50-k
internal pull-ups, and the TCK signal has a fixed 10-k
pull-down resistor.
±2.2-kV human body model (HBM) based on JESD22-A114
Specification
■
±6-kV contact discharge and ±8-kV air gap discharge based
on IEC61000-4-2 level 3A
■
± 8-kV Contact Discharge and ±15-kV Air Gap Discharge based
on IEC61000-4-2 level 4C.
All unused I/Os should be pulled high by using the internal
pull-up resistors. All unused outputs should be left floating. All
I/Os can be driven at full-strength, three-quarter strength,
half-strength, or quarter-strength. These drive strengths are
configured separately for each interface.
GPIOs
This protection ensures the device continues to function after
ESD events up to the levels stated in this section.
The SSRX+, SSRX–, SSTX+, and SSTX– pins only have up to
±2.2-kV HBM internal ESD protection.
EZ-USB enables a flexible pin configuration both on the GPIF II
and the serial peripheral interfaces. Any unused control pins
(except CTL[15]) on the GPIF II interface can be used as GPIOs.
Similarly, any unused pins on the serial peripheral interfaces may
be configured as GPIOs. See Pin Configurations for pin
configuration options.
All GPIF II and GPIO pins support an external load of up to 16 pF
for every pin.
Document Number: 001-52136 Rev. *S
Page 13 of 53
CYUSB301X/CYUSB201X
Pin Configurations
Figure 6. FX3 121-ball BGA Ball Map (Top View)
1
2
3
4
5
6
7
8
9
10
11
A
U3VSSQ
U3RXVDDQ
SSRXM
SSRXP
SSTXP
SSTXM
AVDD
VSS
DP
DM
NC
B
VIO4
FSLC[0]
R_USB3
FSLC[1]
U3TXVDDQ
CVDDQ
AVSS
VSS
VSS
VDD
TRST#
C
GPIO[54]
GPIO[55]
VDD
GPIO[57]
RESET#
XTALIN
XTALOUT
R_USB2
OTG_ID
TDO
D
GPIO[50]
GPIO[51]
GPIO[52]
GPIO[53]
GPIO[56]
CLKIN_32
CLKIN
VSS
E
GPIO[47]
VSS
VIO3
GPIO[49]
GPIO[48]
FSLC[2]
TDI
TMS
F
VIO2
GPIO[45]
GPIO[44]
GPIO[41]
GPIO[46]
TCK
GPIO[2]
G
VSS
GPIO[42]
GPIO[43]
GPIO[30]
GPIO[25]
GPIO[22]
GPIO[21]
H
VDD
GPIO[39]
GPIO[40]
GPIO[31]
GPIO[29]
GPIO[26]
GPIO[20]
J
GPIO[38]
GPIO[36]
GPIO[37]
GPIO[34]
GPIO[28]
GPIO[16]
K
GPIO[35]
GPIO[33]
VSS
VSS
GPIO[27]
L
VSS
VSS
VSS
GPIO[32]
VDD
I2C_GPIO[58] I2C_GPIO[59]
VIO5
O[60]
VDD
VBATT
VBUS
GPIO[5]
GPIO[1]
GPIO[0]
VDD
GPIO[15]
GPIO[4]
GPIO[3]
VSS
GPIO[24]
GPIO[7]
GPIO[6]
VIO1
GPIO[19]
GPIO[14]
GPIO[9]
GPIO[8]
VDD
GPIO[23]
GPIO[18]
GPIO[17]
GPIO[13]
GPIO[12]
GPIO[10]
VSS
VDD
INT#
VIO1
GPIO[11]
VSS
Figure 7. FX3 131-Ball WLCSP Ball Map (Bottom View)
12
11
10
A
VSS
VSS
SSRXM
B
GPIO[55]
VIO4
SSRXP
GPIO[56]
VIO3
GPIO[49]
GPIO[50]
C
D
9
8
7
6
5
4
3
2
1
SSTXM
FSLC[0]
AVSS
AVDD
DP
VSS
DM
VDD
R_USB3
SSTXP
FSLC[2]
XTALIN
XTALOUT
NC
R_USB2
NC
VDD
U3RXVDDQ
U3VSSQ
U3TXVDDQ
CVDDQ
CLKIN_32
CLKIN
VSS
OTG_ID
TDO
TRST#
GPIO[53]
GPIO[54]
RESET#
VDD
I2C_GPIO[58
]
TMS
VIO5
TCK
I2C_GPIO[59
]
VSS
E
GPIO[57]
GPIO[48]
GPIO[51]
GPIO[52]
O[60]
VSS
VSS
VSS
VSS
GPIO[3]
VBATT
VBUS
F
VSS
GPIO[46]
GPIO[47]
FSLC[1]
TDI
VDD
VDD
VDD
VDD
GPIO[4]
GPIO[1]
GPIO[0]
G
VIO2
GPIO[43]
GPIO[44]
GPIO[45]
VSS
VSS
VDD
VSS
GPIO[9]
GPIO[7]
GPIO[6]
GPIO[2]
H
VSS
GPIO[40]
GPIO[41]
GPIO[42]
GPIO[39]
VSS
GPIO[20]
GPIO[18]
GPIO[14]
GPIO[12]
GPIO[8]
VIO1
J
VIO2
GPIO[38]
GPIO[37]
GPIO[36]
GPIO[31]
GPIO[27]
GPIO[25]
GPIO[22]
GPIO[19]
GPIO[15]
GPIO[10]
GPIO[5]
K
GPIO[35]
GPIO[34]
GPIO[33]
GPIO[32]
GPIO[28]
GPIO[26]
GPIO[16]
GPIO[21]
INT#
GPIO[24]
GPIO[11]
VSS
L
VDD
VSS
VDD
GPIO[30]
GPIO[29]
VIO1
GPIO[23]
VSS
VIO1
GPIO[17]
GPIO[13]
VSS
Note No ball is populated at location A9.
Figure 8. FX3 Hi-Speed 121-Ball BGA Ball Map (Top View)
A
1
2
3
4
5
6
7
8
9
10
11
U3VSSQ
VDD
NC
NC
NC
NC
AVDD
VSS
DP
DM
NC
TRST#
B
VIO4
FSLC[0]
NC
FSLC[ 1]
VDD
CVDDQ
AVSS
VSS
VSS
VDD
C
GPIO[ 54]
GPIO[55]
VDD
GPIO[57]
RESET#
XTALIN
XTALOUT
R_USB2
OTG_ID
TDO
D
GPIO[ 50]
GPIO[ 51]
GPIO[ 52]
GPIO[53]
GPIO[ 56]
CLKIN_32
CLKIN
VSS
E
GPIO[ 47]
VSS
VIO3
GPIO[ 49]
GPIO[ 48]
FSLC[ 2]
TDI
TM S
VDD
VBATT
VBUS
F
VIO2
GPIO[45]
GPIO[44]
GPIO[41]
GPIO[ 46]
TCK
GPIO[ 2]
GPIO[5]
GPIO[ 1]
GPIO[0]
VDD
G
VSS
GPIO[ 42]
GPIO[43]
GPIO[ 30]
GPIO[ 25]
GPIO[22]
GPIO[ 21]
GPIO[15]
GPIO[4]
GPIO[3]
VSS
H
VDD
GPIO[ 39]
GPIO[40]
GPIO[31]
GPIO[ 29]
GPIO[26]
GPIO[20]
GPIO[ 24]
GPIO[7]
GPIO[6]
VIO1
J
GPIO[38]
GPIO[ 36]
GPIO[ 37]
GPIO[ 34]
GPIO[ 28]
GPIO[ 16]
GPIO[ 19]
GPIO[14]
GPIO[9]
GPIO[8]
VDD
K
GPIO[ 35]
GPIO[ 33]
VSS
VSS
GPIO[ 27]
GPIO[23]
GPIO[ 18]
GPIO[17]
GPIO[13]
GPIO[12]
GPIO[ 10]
L
VSS
VSS
VSS
GPIO[ 32]
VDD
VSS
VDD
INT#
VIO1
GPIO[ 11]
VSS
Document Number: 001-52136 Rev. *S
I2C_GPIO[ 58] I2C_GPIO[ 59]
VIO5
O[ 60]
Page 14 of 53
CYUSB301X/CYUSB201X
Pin Description
Table 7. CYUSB3012 and CYUSB3014 Pin List
BGA
WLCSP
Power
Domain
I/O
Name
F10
F1
VIO1
I/O
GPIO[0]
DQ[0]
DQ[0]
F9
F2
VIO1
I/O
GPIO[1]
DQ[1]
DQ[1]
Description
GPIF II Interface
Slave FIFO Interface
F7
G1
VIO1
I/O
GPIO[2]
DQ[2]
DQ[2]
G10
E3
VIO1
I/O
GPIO[3]
DQ[3]
DQ[3]
G9
F3
VIO1
I/O
GPIO[4]
DQ[4]
DQ[4]
F8
J1
VIO1
I/O
GPIO[5]
DQ[5]
DQ[5]
H10
G2
VIO1
I/O
GPIO[6]
DQ[6]
DQ[6]
H9
G3
VIO1
I/O
GPIO[7]
DQ[7]
DQ[7]
J10
H2
VIO1
I/O
GPIO[8]
DQ[8]
DQ[8]
J9
G4
VIO1
I/O
GPIO[9]
DQ[9]
DQ[9]
K11
J2
VIO1
I/O
GPIO[10]
DQ[10]
DQ[10]
L10
K2
VIO1
I/O
GPIO[11]
DQ[11]
DQ[11]
K10
H3
VIO1
I/O
GPIO[12]
DQ[12]
DQ[12]
K9
L2
VIO1
I/O
GPIO[13]
DQ[13]
DQ[13]
J8
H4
VIO1
I/O
GPIO[14]
DQ[14]
DQ[14]
DQ[15]
G8
J3
VIO1
I/O
GPIO[15]
DQ[15]
J6
K6
VIO1
I/O
GPIO[16]
PCLK
CLK
K8
L3
VIO1
I/O
GPIO[17]
CTL[0]
SLCS#
K7
H5
VIO1
I/O
GPIO[18]
CTL[1]
SLWR#
J7
J4
VIO1
I/O
GPIO[19]
CTL[2]
SLOE#
H7
H6
VIO1
I/O
GPIO[20]
CTL[3]
SLRD#
G7
K5
VIO1
I/O
GPIO[21]
CTL[4]
FLAGA
G6
J5
VIO1
I/O
GPIO[22]
CTL[5]
FLAGB
K6
L6
VIO1
I/O
GPIO[23]
CTL[6]
GPIO
H8
K3
VIO1
I/O
GPIO[24]
CTL[7]
PKTEND#
G5
J6
VIO1
I/O
GPIO[25]
CTL[8]
GPIO
H6
K7
VIO1
I/O
GPIO[26]
CTL[9]
GPIO
K5
J7
VIO1
I/O
GPIO[27]
CTL[10]
GPIO
A1
J5
K8
VIO1
I/O
GPIO[28]
CTL[11]
H5
L8
VIO1
I/O
GPIO[29]
CTL[12]
A0
G4
L9
VIO1
I/O
GPIO[30]
PMODE[0]
PMODE[0]
H4
J8
VIO1
I/O
GPIO[31]
PMODE[1]
PMODE[1]
L4
K9
VIO1
I/O
GPIO[32]
PMODE[2]
PMODE[2]
L8
K4
VIO1
I/O
INT#
INT#/CTL[15]
CTL[15]
K2
32-bit Data
Bus
16 - bit Data Bus +
UART+SPI+I2S
16 - bit Data
Bus +
UART+GPIO
GPIO
GPIO
K10
VIO2
I/O
GPIO[33]
DQ[16]
16 - bit
16 - bit Data
Data Bus +
Bus +
SPI+GPIO
I2S+GPIO
GPIO
GPIO
GPIO
only
GPIO
J4
K11
VIO2
I/O
GPIO[34]
DQ[17]
GPIO
GPIO
GPIO
GPIO
GPIO
K1
K12
VIO2
I/O
GPIO[35]
DQ[18]
GPIO
GPIO
GPIO
GPIO
GPIO
J2
J9
VIO2
I/O
GPIO[36]
DQ[19]
GPIO
GPIO
GPIO
GPIO
GPIO
J3
J10
VIO2
I/O
GPIO[37]
DQ[20]
GPIO
GPIO
GPIO
GPIO
GPIO
Document Number: 001-52136 Rev. *S
Page 15 of 53
CYUSB301X/CYUSB201X
Table 7. CYUSB3012 and CYUSB3014 Pin List (continued)
BGA
WLCSP
Power
Domain
I/O
Name
Description
J1
J11
VIO2
I/O
GPIO[38]
DQ[21]
GPIO
GPIO
GPIO
GPIO
H2
H8
VIO2
I/O
GPIO[39]
DQ[22]
GPIO
GPIO
GPIO
GPIO
GPIO
GPIO
H3
H11
VIO2
I/O
GPIO[40]
DQ[23]
GPIO
GPIO
GPIO
GPIO
GPIO
F4
H10
VIO2
I/O
GPIO[41]
DQ[24]
GPIO
GPIO
GPIO
GPIO
GPIO
G2
H9
VIO2
I/O
GPIO[42]
DQ[25]
GPIO
GPIO
GPIO
GPIO
GPIO
G3
G11
VIO2
I/O
GPIO[43]
DQ[26]
GPIO
GPIO
GPIO
GPIO
GPIO
F3
G10
VIO2
I/O
GPIO[44]
DQ[27]
GPIO
GPIO
GPIO
GPIO
GPIO
F2
G09
VIO2
I/O
GPIO[45]
GPIO
GPIO
GPIO
GPIO
GPIO
GPIO
GPIO
F5
F11
VIO3
I/O
GPIO[46]
DQ[28]
UART_RT S
GPIO
GPIO
GPIO
E1
F10
VIO3
I/O
GPIO[47]
DQ[29]
UART_CT S
GPIO
GPIO
GPIO
GPIO
E5
E11
VIO3
I/O
GPIO[48]
DQ[30]
UART_TX
GPIO
GPIO
GPIO
GPIO
E4
D12
VIO3
I/O
GPIO[49]
DQ[31]
UART_R X
GPIO
GPIO
GPIO
GPIO
D1
D11
VIO3
I/O
GPIO[50]
I2S_CLK
I2S_CLK
GPIO
GPIO
GPIO
GPIO
D2
E10
VIO3
I/O
GPIO[51]
I2S_SD
I2S_SD
GPIO
GPIO
GPIO
GPIO
D3
E9
VIO3
I/O
GPIO[52]
I2S_WS
I2S_WS
GPIO
GPIO
GPIO
GPIO
D4
D10
VIO4
I/O
GPIO[53]
UART_RTS
SPI_SCK
UART_RTS
SPI_SCK
GPIO
GPIO
C1
D9
VIO4
I/O
GPIO[54]
UART_CTS
SPI_SSN
UART_CTS
SPI_SSN
I2S_CLK
GPIO
C2
B12
VIO4
I/O
GPIO[55]
UART_TX
SPI_MIS O
UART_TX
SPI_MISO
I2S_SD
GPIO
D5
C12
VIO4
I/O
GPIO[56]
UART_RX
SPI_MOS I
UART_RX
SPI_MOSI
I2S_WS
GPIO
C4
E12
VIO4
I/O
GPIO[57]
I2S_MCLK
I2S_MCL K
GPIO
GPIO
I2S_MCL K
GPIO
USB Port
CYUSB301X
CYUSB201X
A3
A10
U3RXVD
DQ
I
SSRXM
SSRX-
NC
A4
B10
U3RXVD
DQ
I
SSRXP
SSRX+
NC
A6
A8
U3TXVD
DQ
O
SSTXM
SSTX-
NC
A5
B8
U3TXVD
DQ
O
SSTXP
SSTX+
NC
B3
B9
U3TXVD
DQ
I/O
R_usb3
Precision resistor for USB 3.0 (Connect a 200
±1% resistor between this pin and GND)
NC
C9
C3
VBUS/
VBATT
I
OTG_ID
OTG_ID
A9
A4
VBUS/V
BATT
I/O
DP
D+
A10
A2
VBUS/V
BATT
I/O
DM
D–
C8
B3
VBUS/VBAT
T
I/O
R_usb2
Precision resistor for USB 2.0 (Connect a 6.04 k ±1% resistor between this pin and GND)
Clock and Reset
B2
A7
CVDDQ
I
FSLC[0]
C6
B6
AVDD
I/O
XTALIN
FSLC[0]
XTALIN
C7
B5
AVDD
I/O
XTALOUT
XTALOUT
B4
F9
CVDDQ
I
FSLC[1]
FSLC[1]
E6
B7
CVDDQ
I
FSLC[2]
FSLC[2]
D7
C5
CVDDQ
I
CLKIN
CLKIN
Document Number: 001-52136 Rev. *S
Page 16 of 53
CYUSB301X/CYUSB201X
Table 7. CYUSB3012 and CYUSB3014 Pin List (continued)
BGA
WLCSP
Power
Domain
I/O
Name
Description
CLKIN_32
D6
C6
CVDDQ
I
CLKIN_32
C5
D8
CVDDQ
I
RESET#
RESET#
I2C and JTAG
D9
D6
VIO5
I/O
I2C_GPIO[58
]
I2C_SCL
D10
D2
VIO5
I/O
I2C_GPIO[59
]
I2C_SDA
E7
F8
VIO5
I
TDI
TDI
C10
C2
VIO5
O
TDO
TDO
B11
C1
VIO5
I
TRST#
TRST#
E8
D5
VIO5
I
TMS
TMS
F6
D3
VIO5
I
TCK
TCK
D11
E8
VIO5
O
O[60]
Charger detect output
E10
E2
PWR
VBATT
B10
B1
PWR
VDD
–
A1
A1
C9
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Power
E11
E1
D8
C4
H11
H1
E2
K1
L9
L4
G1
L5
–
–
L7
L1
F1
J12
G11
H12
G12
E3
C11
L1
F12
B1
B11
L6
A11
–
A12
B6
C7
B5
C8
A2
C10
C11
D4
L11
A3
A7
A5
B7
A6
C3
F4
B8
D1
E9
F5
PWR
VDD
PWR
U3VSSQ
PWR
VBUS
PWR
VSS
PWR
VIO1
PWR
VSS
PWR
VIO1
PWR
VSS
PWR
VIO1
PWR
VSS
PWR
VIO2
PWR
VSS
PWR
VIO2
PWR
VIO3
PWR
VSS
PWR
VIO4
PWR
VSS
PWR
VSS
PWR
CVDDQ
PWR
U3TXVDDQ
PWR
U3RXVDDQ
PWR
VIO5
PWR
VSS
PWR
AVDD
PWR
AVSS
PWR
VDD
PWR
VSS
PWR
VDD
Document Number: 001-52136 Rev. *S
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Page 17 of 53
CYUSB301X/CYUSB201X
Table 7. CYUSB3012 and CYUSB3014 Pin List (continued)
BGA
WLCSP
Power
Domain
I/O
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
B9
E4
F11
F6
–
–
–
–
E5
H1
G6
L7
D7
J11
L10
L5
L12
K4
H7
F7
E6
E7
L3
G7
K3
L11
L2
G8
A8
G5
–
B4
A11
B2
Name
Description
PWR
VSS
PWR
VDD
–
–
PWR
VSS
GND
PWR
VDD
–
PWR
VSS
GND
PWR
VSS
GND
PWR
VDD
PWR
VDD
PWR
VDD
PWR
VDD
PWR
VSS
–
–
–
–
–
PWR
VSS
PWR
VSS
PWR
VSS
PWR
VSS
–
–
–
–
–
–
NC
No Connect
NC
No Connect
Document Number: 001-52136 Rev. *S
Page 18 of 53
CYUSB301X/CYUSB201X
Electrical Specifications
■
Additional ESD protection levels on D+, D–, and GND pins, and
serial peripheral pins
■
Exceeding maximum ratings may shorten the useful life of the
device.
± 6-kV contact discharge, ± 8-kV air gap discharge based on
IEC61000-4-2 level 3A, ± 8-kV contact discharge, and ± 15-kV
air gap discharge based on IEC61000-4-2 level 4C
Storage temperature .................................... –65 °C to +150 °C
Latch-up current .........................................................> 200 mA
Ambient temperature with
power supplied (Industrial) ............................ –40 °C to +85 °C
Maximum output short-circuit current for all I/Os
(cumulative).......... ........................................................ –100 mA
Ambient temperature with
power supplied (Commercial) ............................. 0 °C to +70 °C
Maximum output current per I/O
(source or sink).......................... ...................................... 20 mA
Supply voltage to ground potential
VDD, AVDDQ ......................................................................1.25 V
Operating Conditions
Absolute Maximum Ratings
VIO1,VIO2, VIO3, VIO4, VIO5 ............................................. ...3.6 V
U3TXVDDQ, U3RXVDDQ .............................................. .....1.25 V
DC input voltage to any input pin ........................... .VCC + 0.3 V
TA (ambient temperature under bias)
Industrial ........................................................ –40 °C to +85 °C
Commercial ....................................................... 0 °C to +70 °C
VDD, AVDDQ, U3TXVDDQ, U3RXVDDQ
DC voltage applied to
outputs in high Z state ............................................ VCC + 0.3 V
Supply voltage ..................................................1.15 V to 1.25 V
(VCC is the corresponding I/O voltage)
VBATT supply voltage ...............................................3.2 V to 6 V
Static discharge voltage ESD protection levels:
VIO1, VIO2, VIO3, VIO4, CVDDQ
■
Supply voltage ......................................................1.7 V to 3.6 V
± 2.2-kV HBM based on JESD22-A114
VIO5 supply voltage ............................................ 1.15 V to 3.6 V
DC Specifications
Table 8. DC Specifications
Parameter
Description
Min
Max
Units
Notes
VDD
Core voltage supply
1.15
1.25
V
1.2-V typical
AVDD
Analog voltage supply
1.15
1.25
V
1.2-V typical
VIO1
GPIF II I/O power supply domain
1.7
3.6
V
1.8-, 2.5-, and 3.3-V typical
VIO2
IO2 power supply domain
1.7
3.6
V
1.8-, 2.5-, and 3.3-V typical
VIO3
IO3 power supply domain
1.7
3.6
V
1.8-, 2.5-, and 3.3-V typical
VIO4
UART/SPI/I2S power supply domain
1.7
3.6
V
1.8-, 2.5-, and 3.3-V typical
VBATT
USB voltage supply
3.2
6
V
3.7-V typical
VBUS
USB voltage supply
4.0
6
V
5-V typical
U3TXVDDQ
USB 3.0 1.2-V supply
1.15
1.25
V
1.2-V typical. A 22-µF bypass capacitor is
required on this power supply.
N/A for CYUSB201X
U3RXVDDQ
USB 3.0 1.2-V supply
1.15
1.25
V
1.2-V typical. A 22-µF bypass capacitor is
required on this power supply.
N/A for CYUSB201X
CVDDQ
Clock voltage supply
1.7
3.6
V
1.8-, 3.3-V typical
VIO5
I2C and JTAG voltage supply
1.15
3.6
V
1.2-, 1.8-, 2.5-, and 3.3-V typical
VIH1
Input HIGH voltage 1
0.625 ×
VCC
VCC + 0.3
V
For 2.0 V  VCC  3.6 V (except USB port).
VCC is the corresponding I/O voltage supply.
VIH2
Input HIGH voltage 2
VCC – 0.4 VCC + 0.3
V
For 1.7 V  VCC 2.0 V
(except USB port). VCC is the corresponding
I/O voltage supply.
VIL
Input LOW voltage
V
VCC is the corresponding I/O voltage supply.
Document Number: 001-52136 Rev. *S
–0.3
0.25 × VCC
Page 19 of 53
CYUSB301X/CYUSB201X
Table 8. DC Specifications (continued)
Parameter
Description
Min
Max
Units
Notes
VOH
Output HIGH voltage
0.9 × VCC
–
V
IOH (max) = –100 µA tested at quarter drive
strength. VCC is the corresponding I/O
voltage supply.
VOL
Output LOW voltage
–
0.1 × VCC
V
IOL (min) = +100 µA tested at quarter drive
strength. VCC is the corresponding I/O
voltage supply.
IIX
Input leakage current for all pins
except
SSTXP/SSXM/SSRXP/SSRXM
–1
1
µA
All I/O signals held at VDDQ
(For I/Os with a pull-up or pull-down resistor
connected, the leakage current increases by
VDDQ/Rpu or VDDQ/RPD
IOZ
Output High-Z leakage current for all
pins except SSTXP/ SSXM/
SSRXP/SSRXM
–1
1
µA
All I/O signals held at VDDQ
ICC Core
Core and analog voltage operating
current
–
200
mA
Total current through AVDD, VDD
ICC USB
USB voltage supply operating current
–
60
mA
–
mA
Core current: 1.5 mA
I/O current: 20 µA
USB current: 2 mA
For typical PVT (typical silicon, all power
supplies at their respective nominal levels at
25 °C)
mA
Core current: 250 µA
I/O current: 20 µA
USB current: 1.2 mA
For typical PVT (Typical silicon, all power
supplies at their respective nominal levels at
25 °C)
µA
Core current: 60 µA
I/O current: 20 µA
USB current: 40 µA
For typical PVT (typical silicon, all power
supplies at their respective nominal levels at
25 °C)
µA
Core current: 0 µA
I/O current: 20 µA
USB current: 40 µA
For typical PVT (typical silicon, all power
supplies at their respective nominal levels at
25 °C)
ISB1
ISB2
ISB3
Total suspend current during
suspend mode with USB 3.0 PHY
enabled (L1)
Total suspend current during
suspend mode with USB 3.0 PHY
disabled (L2)
Total standby current during standby
mode (L3)
–
–
–
–
–
–
ISB4
Total standby current during core
power-down mode (L4)
–
–
VRAMP
Voltage ramp rate on core and I/O
supplies
0.2
50
VN
Noise level permitted on VDD and I/O
supplies
–
100
mV
Max p-p noise level permitted on all supplies
except AVDD
VN_AVDD
Noise level permitted on AVDD supply
–
20
mV
Max p-p noise level permitted on AVDD
Document Number: 001-52136 Rev. *S
V/ms Voltage ramp must be monotonic
Page 20 of 53
CYUSB301X/CYUSB201X
AC Timing Parameters
GPIF II Timing
Figure 9. GPIF II Timing in Synchronous Mode
tC LK H tC LKL
C LK
tC LK
tC O
tLZ
- [31:0]
DQ
tD S
tD O H
tLZ
tD O H
D ata 2
( O U T)
D ata 1
( O U T)
D ata ( IN)
tS
tH Z
tC O E
tD H
tH
C TL(IN)
tC TLO
tC O H
C TL ( O U T)
Table 9. GPIF II Timing Parameters in Synchronous Mode [2]
Parameter
Description
Min
Max
Units
Frequency
Interface clock frequency
–
100
MHz
tCLK
Interface clock period
10
–
ns
tCLKH
Clock high time
4
–
ns
tCLKL
Clock low time
4
–
ns
tS
CTL input to clock setup time
2
–
ns
tH
CTL input to clock hold time
0.5
–
ns
tDS
Data in to clock setup time
2
–
ns
tDH
Data in to clock hold time
0.5
–
ns
tCO
Clock to data out propagation delay when DQ bus is already in output direction
–
8
ns
tCOE
Clock to data out propagation delay when DQ lines change to output from
tristate and valid data is available on the DQ bus
–
9
ns
tCTLO
Clock to CTL out propagation delay
–
8
ns
tDOH
Clock to data out hold
2
–
ns
tCOH
Clock to CTL out hold
0
–
ns
tHZ
Clock to high-Z
–
8
ns
tLZ
Clock to low-Z
0
–
ns
Note
2. All parameters guaranteed by design and validated through characterization.
Document Number: 001-52136 Rev. *S
Page 21 of 53
CYUSB301X/CYUSB201X
Figure 10. GPIF II Timing in Asynchronous Mode
tDS/ tAS
tDH/tAH
DATA IN
DATA/ ADDR
tCHZ
CTL#
(I/P , ALE/ DLE)
tCTLassert_DQlatch
tCTLdeassert_DQlatch
tAA/tDO
tCHZ/tOEHZ
tCLZ/ tOELZ
DATA OUT
DATA OUT
CTL#
(I/P, non ALE/ DLE
tCTLdeassert
tCTLassert
tCTLalpha
ALPHA
O/P
tCTLbeta
BETA
O/P
1
tCTLassert
tCTLdeassert
1
tCTL#
(O/P)
1. n is an integer >= 0
tDST
tDHT
DATA/
ADDR
tCTLdeassert_DQassert
tCTLassert_DQassert
CTL#
I/P (non DLE/ALE)
Figure 11. GPIF II Timing in Asynchronous DDR Mode
tDS
tCTLdeassert_DqlatchDDR
tCTLassert_DQlatchDDR
CTL#
(I/P)
tDS
tDH
tDH
DATA IN
Document Number: 001-52136 Rev. *S
Page 22 of 53
CYUSB301X/CYUSB201X
Table 10. GPIF II Timing in Asynchronous Mode[3, 4]
Note The following parameters assume one state transition
Parameter
Description
Min
Max
Units
tDS
Data In to DLE setup time. Valid in DDR async mode.
2.3
–
ns
tDH
Data In to DLE hold time. Valid in DDR async mode.
2
–
ns
tAS
Address In to ALE setup time
2.3
–
ns
tAH
Address In to ALE hold time
2
–
ns
tCTLassert
CTL I/O asserted width for CTRL inputs without DQ input association
and for outputs.
7
–
ns
tCTLdeassert
CTL I/O deasserted width for CTRL inputs without DQ input association and for outputs.
7
–
ns
tCTLassert_DQassert
CTL asserted pulse width for CTL inputs that signify DQ inputs valid
at the asserting edge but do not employ in-built latches (ALE/DLE) for
those DQ inputs.
20
–
ns
tCTLdeassert_DQassert
CTL deasserted pulse width for CTL inputs that signify DQ input valid
at the asserting edge but do not employ in-built latches (ALE/DLE) for
those DQ inputs.
7
–
ns
tCTLassert_DQdeassert
CTL asserted pulse width for CTL inputs that signify DQ inputs valid
at the deasserting edge but do not employ in-built latches (ALE/DLE)
for those DQ inputs.
7
–
ns
tCTLdeassert_DQdeassert
CTL deasserted pulse width for CTL inputs that signify DQ inputs valid
at the deasserting edge but do not employ in-built latches (ALE/DLE)
for those DQ inputs.
20
–
ns
tCTLassert_DQlatch
CTL asserted pulse width for CTL inputs that employ in-built latches
(ALE/DLE) to latch the DQ inputs. In this non-DDR case, in-built
latches are always close at the deasserting edge.
7
–
ns
tCTLdeassert_DQlatch
CTL deasserted pulse width for CTL inputs that employ in-built latches
(ALE/DLE) to latch the DQ inputs. In this non-DDR case, in-built
latches always close at the deasserting edge.
10
–
ns
tCTLassert_DQlatchDDR
CTL asserted pulse width for CTL inputs that employ in-built latches
(DLE) to latch the DQ inputs in DDR mode.
10
–
ns
tCTLdeassert_DQlatchDDR
CTL deasserted pulse width for CTL inputs that employ in-built latches
(DLE) to latch the DQ inputs in DDR mode.
10
–
ns
tAA
DQ/CTL input to DQ output time when DQ change or CTL change
needs to be detected and affects internal updates of input and output
DQ lines.
–
30
ns
tDO
CTL to data out when the CTL change merely enables the output flop
update whose data was already established.
–
25
ns
tOELZ
CTL designated as OE to low-Z. Time when external devices should
stop driving data.
0
–
ns
tOEHZ
CTL designated as OE to high-Z
8
8
ns
tCLZ
CTL (non-OE) to low-Z. Time when external devices should stop
driving data.
0
–
ns
tCHZ
CTL (non-OE) to high-Z
30
30
ns
tCTLalpha
CTL to alpha change at output
–
25
ns
tCTLbeta
CTL to beta change at output
–
30
ns
tDST
Addr/data setup when DLE/ALE not used
2
–
ns
tDHT
Addr/data hold when DLE/ALE not used
20
–
ns
Notes
3. All parameters guaranteed by design and validated through characterization.
4. "alpha" output corresponds to "early output" and "beta" corresponds to "delayed output". Please refer to the GPIFII Designer Tool for the use of these outputs.
Document Number: 001-52136 Rev. *S
Page 23 of 53
CYUSB301X/CYUSB201X
Slave FIFO Interface
FLAG Usage:
The FLAG signals are monitored for flow control by the external
processor. FLAG signals are outputs from FX3 that may be
configured to show empty, full, or partial status for a dedicated
thread or the current thread that is addressed.
Synchronous Slave FIFO Read Sequence Description
■
FIFO address is stable and SLCS is asserted
■
FLAG indicates FIFO not empty status
■
SLOE is asserted. SLOE is an output-enable only, whose sole
function is to drive the data bus.
■
SLRD is asserted
Socket Switching Delay (Tssd):
The FIFO pointer is updated on the rising edge of the PCLK,
while the SLRD is asserted. This starts the propagation of data
from the newly addressed location to the data bus. After a propagation delay of tco (measured from the rising edge of PCLK), the
new data value is present. N is the first data value read from the
FIFO. To have data on the FIFO data bus, SLOE must also be
asserted.
The same sequence of events is applicable for a burst read.
The socket-switching delay is measured from the time
EPSWITCH# is asserted by the master, with the new socket
address on the address bus, to the time the
Current_Thread_DMA_Ready flag is asserted. For the Producer
socket, the flag is asserted when it is ready to receive data in the
DMA buffer. For the Consumer socket, the flag is asserted when
it is ready to drive data out of the DMA buffer. For a synchronous
slave FIFO interface, the switching delay is measured in the
number of GPIF interface clock cycles; for an asynchronous
slave FIFO interface, in PIB clock cycles. This is applicable only
for the 5-bit Slave FIFO interface; there is no socket-switching
delay in FX3's 2-bit Slave FIFO interface, which makes use of
thread switching in the GPIF™ II state machine.
Note For burst mode, the SLRD# and SLOE# are asserted
during the entire duration of the read. When SLOE# is asserted,
the data bus is driven (with data from the previously addressed
FIFO). For each subsequent rising edge of PCLK, while the
SLRD# is asserted, the FIFO pointer is incremented and the next
data value is placed on the data bus.
Figure 12. Synchronous Slave FIFO Read Mode
Synchronous Read Cycle Timing
t CYC
PCLK
tCH
tCL
t ACCD
SLCS
tAS tAH
FIFO ADDR
An
Am
t RDS tRDH
SLRD
SLOE
Tssd
t ACCD
t CFLG
FLAGA
( dedicated thread Flag for An )
( 1 = Not Empty 0 = Empty )
Tssd
t CFLG
FLAGB
(dedicated thread Flag for Am )
( 1 = Not Empty 0 = Empty )
tOELZ
Data Out
High-Z
tCDH
tOEZ
Data
driven:DN (An)
High-Z
DN (An)
tCO
DN ( Am)
t OEZ
DN+1 (Am)
DN+2 (Am)
High-Z
SLWR( HIGH)
Document Number: 001-52136 Rev. *S
Page 24 of 53
CYUSB301X/CYUSB201X
Short Packet: A short packet can be committed to the USB host
by using the PKTEND#. The external device or processor should
be designed to assert the PKTEND# along with the last word of
data and SLWR# pulse corresponding to the last word. The
FIFOADDR lines must be held constant during the PKTEND#
assertion.
Synchronous Slave FIFO Write Sequence Description
■
FIFO address is stable and the signal SLCS# is asserted
■
External master or peripheral outputs the data to the data bus
■
SLWR# is asserted
■
While the SLWR# is asserted, data is written to the FIFO and
on the rising edge of the PCLK, the FIFO pointer is incremented
■
The FIFO flag is updated after a delay of t WFLG from the rising
edge of the clock
Zero-Length Packet: The external device or processor can
signal a Zero-Length Packet (ZLP) to FX3 simply by asserting
PKTEND#, without asserting SLWR#. SLCS# and address must
be driven as shown in Figure 13.
The same sequence of events is also applicable for burst write
Note For the burst mode, SLWR# and SLCS# are asserted for
the entire duration, during which all the required data values are
written. In this burst write mode, after the SLWR# is asserted, the
data on the FIFO data bus is written to the FIFO on every rising
edge of PCLK. The FIFO pointer is updated on each rising edge
of PCLK.
Figure 13. Synchronous Slave FIFO Write Mode
Synchronous Write Cycle Timing
tCYC
PCLK
tCH
tCL
SLCS
tAS tAH
Am
An
FIFO ADDR
tWRS
Tssd
tWRH
SLWR
t CFLG
tFAD
FLAGA
dedicated thread FLAG for An
( 1 = Not Full0 = Full)
Tssd
FLAGB
current thread FLAG for Am
( 1 = Not Full0 = Full)
Data IN
tDS tDH
High-Z
DN (An)
tFAD
tDS tDH
DN ( Am)
t CFLG
tDH
DN+1 (Am) DN+2 (Am)
tPES tPEH
PKTEND
SLOE
( HIGH)
Document Number: 001-52136 Rev. *S
Page 25 of 53
CYUSB301X/CYUSB201X
Figure 14. Synchronous Slave FIFO ZLP Write Cycle Timing
Synchronous ZLP Write Cycle Timing
tCYC
PCLK
t CH
tCL
SLCS
tAS t AH
An
FIFO ADDR
SLWR
(HIGH)
tPES tPEH
PKTEND
t CFLG
FLAGA
dedicated thread FLAG for An
(1 = Not Full 0= Full)
FLAGB
current thread FLAG for Am
(1 = Not Full 0= Full)
Data IN
High-Z
SLOE
(HIGH)
Table 11. Synchronous Slave FIFO Parameters[5]
Parameter
Description
FREQ
Interface clock frequency
tCYC
Clock period
tCH
Clock high time
tCL
Clock low time
tRDS
SLRD# to CLK setup time
tRDH
SLRD# to CLK hold time
tWRS
SLWR# to CLK setup time
tWRH
SLWR# to CLK hold time
tCO
Clock to valid data
tDS
Data input setup time
tDH
CLK to data input hold
tAS
Address to CLK setup time
tAH
CLK to address hold time
tOELZ
SLOE# to data low-Z
tCFLG
CLK to flag output propagation delay
tOEZ
SLOE# deassert to Data Hi Z
tPES
PKTEND# to CLK setup
tPEH
CLK to PKTEND# hold
tCDH
CLK to data output hold
tSSD
Socket switching delay
tACCD
Latency from SLRD# to Data
tFAD
Latency from SLWR# to FLAG
Note Three-cycle latency from ADDR to DATA/FLAGS.
Min
–
10
4
4
2
0.5
2
0.5
–
2
0.5
2
0.5
0
–
–
2
0.5
2
2
2
3
Max
100
–
–
–
–
–
–
–
8
–
–
–
–
–
8
8
–
–
–
68
2
3
Units
MHz
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Clock cycles
Clock cycles
Clock cycles
Note
5. All parameters guaranteed by design and validated through characterization.
Document Number: 001-52136 Rev. *S
Page 26 of 53
CYUSB301X/CYUSB201X
Asynchronous Slave FIFO Read Sequence Description
■
FIFO address is stable and the SLCS# signal is asserted.
■
SLOE# is asserted. This results in driving the data bus.
In Figure 15, data N is the first valid data read from the FIFO. For
data to appear on the data bus during the read cycle, SLOE#
must be in an asserted state. SLRD# and SLOE# can also be
tied.
■
SLRD # is asserted.
The same sequence of events is also shown for a burst read.
■
Data from the FIFO is driven after assertion of SLRD#. This
data is valid after a propagation delay of tRDO from the falling
edge of SLRD#.
■
FIFO pointer is incremented on deassertion of SLRD#
Note In the burst read mode, during SLOE# assertion, the data
bus is in a driven state (data is driven from a previously
addressed FIFO). After assertion of SLRD# data from the FIFO
is driven on the data bus (SLOE# must also be asserted). The
FIFO pointer is incremented after deassertion of SLRD#.
Figure 15. Asynchronous Slave FIFO Read Mode
Asynchronous Read Cycle Timing
SLCS
tAS
tAH
An
FIFO ADDR
tRDl
Am
tRDh
SLRD
SLOE
tFLG
tRFLG
FLAGA
dedicated thread Flag for An
(1=Not empty 0 = Empty)
FLAGB
dedicated thread Flag for Am
(1=Not empty 0 = Empty)
tOE
tRDO
tOH
tOE
tRDO
tRDO
tOH
tLZ
Data Out
High-Z
DN(An)
DN(An)
DN(Am)
DN+1(Am)
DN+2(Am)
SLWR
(HIGH)
Document Number: 001-52136 Rev. *S
Page 27 of 53
CYUSB301X/CYUSB201X
Asynchronous Slave FIFO Write Sequence Description
■
FIFO address is driven and SLCS# is asserted
■
SLWR# is asserted. SLCS# must be asserted with SLWR# or
before SLWR# is asserted
■
Data must be present on the tWRS bus before the deasserting
edge of SLWR#
■
Deassertion of SLWR# causes the data to be written from the
data bus to the FIFO, and then the FIFO pointer is incremented
■
The FIFO flag is updated after the tWFLG from the deasserting
edge of SLWR.
The same sequence of events is shown for a burst write.
Short Packet: A short packet can be committed to the USB host
by using the PKTEND#. The external device or processor should
be designed to assert the PKTEND# along with the last word of
data and SLWR# pulse corresponding to the last word. The
FIFOADDR lines must be held constant during the PKTEND#
assertion.
Zero-Length Packet: The external device or processor can
signal a zero-length packet (ZLP) to FX3 simply by asserting
PKTEND#, without asserting SLWR#. SLCS# and the address
must be driven as shown in Figure 17 on page 29.
FLAG Usage: The FLAG signals are monitored by the external
processor for flow control. FLAG signals are FX3 outputs that
can be configured to show empty, full, and partial status for a
dedicated address or the current address.
Note that in the burst write mode, after SLWR# deassertion, the
data is written to the FIFO, and then the FIFO pointer is incremented.
Figure 16. Asynchronous Slave FIFO Write Mode
Asynchronous Write Cycle Timing
SLCS
tAS
tAH
An
FIFO ADDR
tWRl
Am
tWRh
SLWR
tFLG
t WFLG
FLAGA
dedicated thread Flag for An
(1= Not Full 0 = Full)
t WFLG
FLAGB
dedicated thread Flag for Am
(1= Not Full 0 = Full)
DATA In
tWR
S
High-Z
tWRH
tWR
t WRH
S
DN (An)
DN (Am)
DN+1 (Am)
DN+2 (Am)
t WRPE
t
PEh
PKTEND
SLOE
( HIGH)
tWRPE: SLWR# de- assert to PKTEND deassert
= 2 ns min(
This means that PKTEND should not be be deasserted before SLWR
#)
Note:
PKTEND must be asserted at the same time as SLWR
#.
Document Number: 001-52136 Rev. *S
Page 28 of 53
CYUSB301X/CYUSB201X
Figure 17. Asynchronous ZLP Write Cycle Timing
SLCS
tA S
tA H
An
F IF O A D D R
SLW R
( H IG H)
tP E l t P E h
PKTEND
t W FLG
FLAG A
d e d ic a te d th re a d F la g fo r A n
( 1 = N o t F u ll 0 = F u ll)
FLAG B
d e d ic a te d th re a d F la g fo r A m
( 1 = N o t F u ll 0 = F u ll)
H ig h- Z
D A T A In
SLO E
( H IG H)
Table 12. Asynchronous Slave FIFO Parameters[6]
Parameter
Min
Max
Units
SLRD# low
20
–
ns
tRDh
SLRD# high
10
–
ns
tAS
Address to SLRD#/SLWR# setup time
7
–
ns
tAH
SLRD#/SLWR#/PKTEND to address hold time
2
–
ns
tRFLG
SLRD# to FLAGS output propagation delay
–
35
ns
tFLG
ADDR to FLAGS output propagation delay
–
22.5
ns
tRDO
SLRD# to data valid
–
25
ns
tOE
OE# low to data valid
–
25
ns
tLZ
OE# low to data low-Z
0
–
ns
tOH
SLOE# deassert data output hold
–
22.5
ns
tWRI
SLWR# low
20
–
ns
tWRh
SLWR# high
10
–
ns
tWRS
Data to SLWR# setup time
7
–
ns
tRDI
Description
tWRH
SLWR# to Data Hold time
2
–
ns
tWFLG
SLWR#/PKTEND to Flags output propagation delay
–
35
ns
tPEI
PKTEND low
20
–
ns
tPEh
PKTEND high
7.5
–
ns
tWRPE
SLWR# deassert to PKTEND deassert
2
–
ns
Note
6. All parameters guaranteed by design and validated through characterization.
Document Number: 001-52136 Rev. *S
Page 29 of 53
CYUSB301X/CYUSB201X
Host Processor Interface (P-Port) Timing
Asynchronous SRAM Timing
Figure 18. Non-multiplexed Asynchronous SRAM Read Timing
Socket Read – Address Transition Controlled Timing (OE# is asserted)
A[0]
tAA
tAH
tOH
DATA
OUT
HIGH
IMPEDANCE
DATA VALID
DATA VALID
DATA VALID
tOE
OE#
OE# Controlled Timing
ADDRESS
WE# (HIGH)
tAOS
CE#
tOHC
tRC
OE#
tOHH
tOE
tOEZ
tOLZ
DATA OUT
HIGH
IMPEDANCE
Document Number: 001-52136 Rev. *S
DATA
VALID
HIGH
IMPEDANCE
DATA
VALID
HIGH
IMPEDANCE
Page 30 of 53
CYUSB301X/CYUSB201X
Figure 19. Non-multiplexed Asynchronous SRAM Write Timing (WE# and CE# Controlled)
Write Cycle 1 WE# Controlled, OE# High During Write
tWC
ADDRESS
tCW
CE#
tAW
tAH
tWP
WE#
tAS
tWPH
OE#
tDS
DATA I/O
tDH
VALID DATA
VALID DATA
tWHZ
Write Cycle 2 CE# Controlled, OE# High During Write
tWC
ADDRESS
tAS
tCW
tCPH
CE#
tAW
tAH
tWP
WE#
OE#
tDS
DATA I/O
VALID DATA
tDH
VALID DATA
tWHZ
Document Number: 001-52136 Rev. *S
Page 31 of 53
CYUSB301X/CYUSB201X
Figure 20. Non-multiplexed Asynchronous SRAM Write Timing (WE# controlled, OE# LOW)
Write Cycle 3 WE# Controlled. OE# Low
tWC
tCW
CE#
tAW
tAH
tAS
tWP
WE#
tDS
DATA I/O
tDH
VALID DATA
tOW
tWHZ
Note: tWP must be adjusted such that tWP > tWHZ + tDS
Table 13. Asynchronous SRAM Timing Parameters[7]
Parameter
–
Description
SRAM interface bandwidth
Min
Max
Units
–
61.5
Mbps
32.5
–
ns
tRC
Read cycle time
tAA
Address to data valid
–
30
ns
tAOS
Address to OE# LOW setup time
7
–
ns
tOH
Data output hold from address change
3
–
ns
ns
tOHH
OE# HIGH hold time
7.5
–
tOHC
OE# HIGH to CE# HIGH
2
–
ns
tOE
OE# LOW to data valid
–
25
ns
tOLZ
OE# LOW to LOW-Z
0
–
ns
tWC
Write cycle time
30
–
ns
tCW
CE# LOW to write end
30
–
ns
tAW
Address valid to write end
30
–
ns
tAS
Address setup to write start
7
–
ns
tAH
Address hold time from CE# or WE#
2
–
ns
tWP
WE# pulse width
20
–
ns
tWPH
WE# HIGH time
10
–
ns
tCPH
CE# HIGH time
10
–
ns
tDS
Data setup to write end
7
–
ns
tDH
Data hold to write end
2
–
ns
tWHZ
Write to DQ HIGH-Z output
–
22.5
ns
tOEZ
OE# HIGH to DQ HIGH-Z output
–
22.5
ns
tOW
End of write to LOW-Z output
0
–
ns
Note
7. All parameters guaranteed by design and validated through characterization.
Document Number: 001-52136 Rev. *S
Page 32 of 53
CYUSB301X/CYUSB201X
ADMux Timing for Asynchronous Access
Figure 21. ADMux Asynchronous Random Read
tRC
tACC
Valid Address
A[0:7]/DQ[0:15]
tAVS
tAVH
tVP
ADV#
WE# (HIGH)
Valid
Addr
Valid Data
tCEAV
tHZ
tCO
CE#
tCPH
tHZ
tOLZ
tOE
OE#
tAVOE
Note:
1. Multiple read cycles can be executed while keeping CE# low.
2. Read operation ends with either de-assertion of either OE# or CE#, whichever comes earlier.
Figure 22. ADMux Asynchronous Random Write
tWC
Address Valid
A[0:7]/DQ[0:15]
Valid
Addr
Data Valid
tAW
tAVS
ADV#
tCEAV
CE#
tAVH
tDS
tDH
tVPH
tVP
tCPH
tCW
tWP
WE#
tWPH
tAVWE
Note:
1. Multiple write cycles can be executed while keeping CE# low.
2. Write operation ends with de-assertion of either WE# or CE#, whichever comes earlier.
Document Number: 001-52136 Rev. *S
Page 33 of 53
CYUSB301X/CYUSB201X
Table 14. Asynchronous ADMux Timing Parameters[8]
Parameter
Description
Min
Max
Units
Notes
ADMux Asynchronous READ Access Timing Parameters
tRC
Read cycle time (address valid to address
valid)
tACC
Address valid to data valid
–
32
ns
–
tCO
CE# assert to data valid
–
34.5
ns
–
tAVOE
ADV# deassert to OE# assert
2
–
ns
–
tOLZ
OE# assert to data LOW-Z
0
–
ns
–
54.5
–
ns
This parameter is dependent on when
the P-port processors deasserts OE#
tOE
OE# assert to data valid
–
25
ns
–
tHZ
Read cycle end to data HIGH-Z
–
22.5
ns
–
tWC
Write cycle time (Address Valid to Address
Valid)
–
52.5
ns
–
tAW
Address valid to write end
30
–
ns
–
tCW
CE# assert to write end
30
–
ns
–
tAVWE
ADV# deassert to WE# assert
2
–
ns
–
tWP
WE# LOW pulse width
20
–
ns
–
tWPH
WE# HIGH pulse width
10
–
ns
–
tDS
Data valid setup to WE# deassert
18
–
ns
–
tDH
Data valid hold from WE# deassert
2
–
ns
–
tAVS
Address valid setup to ADV# deassert
tAVH
Address valid hold from ADV# deassert
tVP
ADV# LOW pulse width
tCPH
CE# HIGH pulse width
tVPH
ADV# HIGH pulse width
tCEAV
CE# assert to ADV# assert
ADMux Asynchronous WRITE Access Timing Parameters
ADMux Asynchronous Common READ/WRITE Access Timing Parameters
5
–
ns
–
2
–
ns
–
7.5
–
ns
–
10
–
ns
–
15
–
ns
–
0
–
ns
–
Note
8. All parameters guaranteed by design and validated through characterization.
Document Number: 001-52136 Rev. *S
Page 34 of 53
CYUSB301X/CYUSB201X
Synchronous ADMux Timing
Figure 23. Synchronous ADMux Interface – Read Cycle Timing
tCLK
2- cycle latency from OE# to DATA
tCLKH
tCLKL
CLK
tCO
tS
A[0:7]/DQ[0:31]
tH
Valid Data
Valid Address
tS
tH
ADV#
tOHZ
tS
CE#
tAVOE
tOLZ
OE#
tKW
tKW
RDY
tCH
WE# (HIGH)
Note:
1) External P-Port processor and FX3 operate on the same clock edge
2) External processor sees RDY assert 2 cycles after OE # asserts andand sees RDY deassert a cycle after the data appears on the output
3) Valid output data appears 2 cycle after OE # asserted. The data is held until OE # deasserts
4) Two cycle latency is shown for 0-100 MHz operation. Latency can be reduced by 1 cycle for operations at less than 50 MHz (this 1 cycle latency is not supported by the bootloader)
Figure 24. Synchronous ADMux Interface – Write Cycle Timing
2-cycle latency between
WE# and data being latched
2-cycle latency between this clk edge and RDY deassertion seen by
the host
CLK
tCLK
tS
A[0:7]/DQ[0:31]
tDS
tH
Valid Address
tS
tDH
Valid Data
tH
ADV#
tS
CE#
tAVWE
tS
tH
WE#
tKW
RDY
tKW
Note:
1) External P-Port processor and FX3 operate on the same clock edge
2) External processor sees RDY assert 2 cycles after WE # asserts and deassert 3 cycles after the edge sampling the data.
3) Two cycle latency is shown for 0-100 MHz operation. Latency can be reduced by 1 cycle for operations at less than 50 MHz (this 1 cycle latency is not supported by the bootloader )
Document Number: 001-52136 Rev. *S
Page 35 of 53
CYUSB301X/CYUSB201X
Figure 25. Synchronous ADMux Interface – Burst Read Timing
2-cycle latency from OE# to Data
tCLK
tCLKH
tCLKL
CLK
tCO
tS
A[0:7]/DQ[0:31]
tCH
tH
Valid Address
tS
D0
D1
D2
D3
tH
ADV#
tHZ
tS
CE#
tAVOE
tOLZ
OE#
tKW
tKW
RDY
Note:
1) External P-Port processor and FX3 work operate on the same clock edge
2) External processor sees RDY assert 2 cycles after OE # asserts andand sees RDY deassert a cycle after the last burst data appears on the output
3) Valid output data appears 2 cycle after OE # asserted. The last burst data is held until OE # deasserts
4) Burst size of 4 is shown. Transfer size for the operation must be a multiple of burst size. Burst size is usually power of 2. RDY will not deassert in the middle of the burst.
5) External processor cannot deassert OE in the middle of a burst. If it does so, any bytes remaining in the burst packet could get lost.
6) Two cycle latency is shown for 0-100 MHz operation. Latency can be reduced by 1 cycle for operations at less than 50 MHz (this 1 cycle latency is not supported by the bootloader)
Figure 26. Sync ADMux Interface – Burst Write Timing
2-cycle latency between
WE# and data being latched
tCLKH
2-cycle latency between this clk edge and RDY
deassertion seen by the host
tCLKL
CLK
tCLK
tS
A[0:7]/DQ[0:31]
tDS
tH
D0
Valid Address
tS
tDH
tDH
D1
D2
D3
tH
ADV#
tS
CE#
tAVWE
WE#
RDY
tKW
tKW
Note:
1) External P-Port processor and FX3 operate on the same clock edge
2) External processor sees RDY assert 2 cycles after WE # asserts and deasserts 3 cycles after the edge sampling the last burst data.
3) Transfer size for the operation must be a multiple of burst size. Burst size is usually power of 2. RDY will not deassert in the middle of the burst. Burst size of 4 is shown
4) External processor cannot deassert WE in the middle of a burst. If it does so, any bytes remaining in the burst packet could get lost.
5)Two cycle latency is shown for 0-100 MHz operation. Latency can be reduced by 1 cycle for operations at less than 50 MHz (this 1 cycle latency is not supported by the bootloader)
Document Number: 001-52136 Rev. *S
Page 36 of 53
CYUSB301X/CYUSB201X
Table 15. Synchronous ADMux Timing Parameters[9]
Parameter
Description
Min
Max
Unit
FREQ
Interface clock frequency
–
100
MHz
tCLK
Clock period
10
–
ns
tCLKH
Clock HIGH time
4
–
ns
tCLKL
Clock LOW time
4
–
ns
tS
CE#/WE#/DQ setup time
2
–
ns
tH
CE#/WE#/DQ hold time
0.5
–
ns
tCH
Clock to data output hold time
0
–
ns
tDS
Data input setup time
2
–
ns
tDH
Clock to data input hold
0.5
–
ns
tAVDOE
ADV# HIGH to OE# LOW
0
–
ns
tAVDWE
ADV# HIGH to WE# LOW
0
–
ns
tHZ
CE# HIGH to Data HIGH-Z
–
8
ns
tOHZ
OE# HIGH to Data HIGH-Z
–
8
ns
tOLZ
OE# LOW to Data LOW-Z
0
–
ns
tKW
Clock to RDY valid
–
8
ns
Serial Peripherals Timing
I2C Timing
Figure 27. I2C Timing Definition
Note
9. All parameters guaranteed by design and validated through characterization.
Document Number: 001-52136 Rev. *S
Page 37 of 53
CYUSB301X/CYUSB201X
Table 16. I2C Timing Parameters[10]
Parameter
Description
Min
Max
Units
I2C Standard Mode Parameters
fSCL
SCL clock frequency
0
100
kHz
tHD:STA
Hold time START condition
4
–
µs
tLOW
LOW period of the SCL
4.7
–
µs
tHIGH
HIGH period of the SCL
4
–
µs
tSU:STA
Setup time for a repeated START condition
4.7
–
µs
tHD:DAT
Data hold time
0
–
µs
tSU:DAT
Data setup time
250
–
ns
tr
Rise time of both SDA and SCL signals
–
1000
ns
tf
Fall time of both SDA and SCL signals
–
300
ns
tSU:STO
Setup time for STOP condition
4
–
µs
tBUF
Bus free time between a STOP and START condition
4.7
–
µs
tVD:DAT
Data valid time
–
3.45
µs
tVD:ACK
Data valid ACK
–
3.45
µs
tSP
Pulse width of spikes that must be suppressed by input filter
n/a
n/a
0
400
kHz
I
2C
Fast Mode Parameters
fSCL
SCL clock frequency
tHD:STA
Hold time START condition
0.6
–
µs
tLOW
LOW period of the SCL
1.3
–
µs
tHIGH
HIGH period of the SCL
0.6
–
µs
tSU:STA
Setup time for a repeated START condition
0.6
–
µs
tHD:DAT
Data hold time
0
–
µs
tSU:DAT
Data setup time
100
–
ns
tr
Rise time of both SDA and SCL signals
–
300
ns
tf
Fall time of both SDA and SCL signals
–
300
ns
tSU:STO
Setup time for STOP condition
0.6
–
µs
tBUF
Bus free time between a STOP and START condition
1.3
–
µs
tVD:DAT
Data valid time
–
0.9
µs
tVD:ACK
Data valid ACK
–
0.9
µs
tSP
Pulse width of spikes that must be suppressed by input filter
0
50
ns
Note
10. All parameters guaranteed by design and validated through characterization.
Document Number: 001-52136 Rev. *S
Page 38 of 53
CYUSB301X/CYUSB201X
Table 16. I2C Timing Parameters[10] (continued)
Parameter
Description
Min
Max
Units
2
I C Fast Mode Plus Parameters (Not supported at I2C_VDDQ=1.2 V)
fSCL
SCL clock frequency
0
1000
kHz
tHD:STA
Hold time START condition
0.26
–
µs
tLOW
LOW period of the SCL
0.5
–
µs
tHIGH
HIGH period of the SCL
0.26
–
µs
tSU:STA
Setup time for a repeated START condition
0.26
–
µs
tHD:DAT
Data hold time
0
–
µs
tSU:DAT
Data setup time
50
–
ns
tr
Rise time of both SDA and SCL signals
–
120
ns
tf
Fall time of both SDA and SCL signals
–
120
ns
tSU:STO
Setup time for STOP condition
0.26
–
µs
tBUF
Bus-free time between a STOP and START condition
0.5
–
µs
tVD:DAT
Data valid time
–
0.45
µs
tVD:ACK
Data valid ACK
–
0.55
µs
tSP
Pulse width of spikes that must be suppressed by input filter
0
50
ns
I2S Timing Diagram
Figure 28. I2S Transmit Cycle
tT
tTR
tTF
tTL
tTH
SCK
tThd
SA,
WS (output)
tTd
Table 17. I2S Timing Parameters[11]
Parameter
Description
Min
Max
Units
Ttr
–
ns
transmitter cycle LOW period
0.35 Ttr
–
ns
transmitter cycle HIGH period
0.35 Ttr
–
ns
–
0.15 Ttr
ns
–
0.15 Ttr
ns
transmitter data hold time
0
–
ns
transmitter delay time
–
0.8tT
ns
tT
I2S transmitter clock cycle
tTL
I 2S
tTH
I 2S
tTR
I 2S
transmitter rise time
tTF
I2S transmitter fall time
tThd
I 2S
tTd
I 2S
Note tT is selectable through clock gears. Max Ttr is designed for 96-kHz codec at 32 bits to be 326 ns (3.072 MHz).
Note
11. All parameters guaranteed by design and validated through characterization.
Document Number: 001-52136 Rev. *S
Page 39 of 53
CYUSB301X/CYUSB201X
SPI Timing Specification
Figure 29. SPI Timing
SSN
(output)
tssnh
tsck
tlead
SCK
(CPOL=0,
Output)
trf
twsck
SCK
(CPOL=1,
Output)
tsdi
MISO
(input)
tlag
twsck
thoi
MSB
LSB
td
tsdd
tdis
tdi
v
MOSI
(output)
LSB
MSB
SPI Master Timing for CPHA = 0
SSN
(output)
SCK
(CPOL=0,
Output)
tssnh
tsck
tlead
twsck
trf
tlag
twsck
SCK
(CPOL=1,
Output)
tsdi
MISO
(input)
thoi
LSB
tdv
MOSI
(output)
MSB
tdis
tdi
LSB
MSB
SPI Master Timing for CPHA = 1
Document Number: 001-52136 Rev. *S
Page 40 of 53
CYUSB301X/CYUSB201X
Table 18. SPI Timing Parameters[12]
Parameter
fop
tsck
twsck
tlead
tlag
trf
tsdd
tdv
tdi
tssnh
tsdi
thoi
tdis
Description
Operating frequency
Cycle time
Clock high/low time
SSN-SCK lead time
Enable lag time
Rise/fall time
Output SSN to valid data delay time
Output data valid time
Output data invalid
Minimum SSN high time
Data setup time input
Data hold time input
Disable data output on SSN high
Min
0
30
13.5
1/2 tsck[13 ]-5
0.5
–
–
–
0
10
8
0
0
Max
33
–
–
1.5 tsck[13]+ 5
1.5 tsck[13]+5
8
5
5
–
–
–
–
–
Units
MHz
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Notes
12. All parameters guaranteed by design and validated through characterization.
13. Depends on LAG and LEAD setting in the SPI_CONFIG register.
Document Number: 001-52136 Rev. *S
Page 41 of 53
CYUSB301X/CYUSB201X
Reset Sequence
FX3’s hard reset sequence requirements are specified in this section.
Table 19. Reset and Standby Timing Parameters
Parameter
Definition
tRPW
Minimum RESET# pulse width
tRH
Minimum high on RESET#
tRR
Reset recovery time (after which Boot loader begins firmware download)
tSBY
Time to enter standby/suspend (from the time MAIN_CLOCK_EN/
MAIN_POWER_EN bit is set)
tWU
Time to wakeup from standby
tWH
Minimum time before Standby/Suspend source may be reasserted
Conditions
Min (ms)
Max (ms)
Clock Input
1
–
Crystal Input
1
–
–
5
–
–
Clock Input
1
Crystal Input
5
–
–
1
Clock Input
1
–
Crystal Input
5
–
–
5
–
Figure 30. Reset Sequence
VDD
( core )
xVDDQ
XTALIN/
CLKIN
XTALIN/ CLKIN must be stable
before exiting Standby/Suspend
Mandatory
Reset Pulse
tRh
tRR
Hard Reset
RESET #
tWH
tRPW
Standby/
Suspend
Source
tSBY
Standby/Suspend source Is asserted
(MAIN_POWER_EN/ MAIN_CLK_EN bit
is set)
Document Number: 001-52136 Rev. *S
tWU
Standby/Suspend
source Is deasserted
Page 42 of 53
CYUSB301X/CYUSB201X
Package Diagram
Figure 31. 121-ball BGA Package Diagram
2X
0.10 C
E1
E
B
A
11 10
9
8
7
6
5
(datum B)
4 3 2
A1 CORNER
1
7
A1 CORNER
A
B
C
D
6
E
SD
D1
F
D
(datum A)
G
H
J
K
eD
0.10 C 2X
L
6
eE
SE
TOP VIEW
BOTTOM VIEW
0.20 C
DETAIL A
A1
0.08 C
C
121XØb
5
A
Ø0.15 M C A B
Ø0.08 M C
SIDE VIEW
DETAIL A
NOTES:
1. ALL DIMENSIONS ARE IN MILLIMETERS.
DIMENSIONS
SYMBOL
MIN.
NOM.
MAX.
A
-
-
1.20
A1
0.15
-
-
D
10.00 BSC
E
10.00 BSC
D1
8.00 BSC
E1
8.00 BSC
MD
11
ME
11
N
121
b
0.25
0.30
eD
0.80 BSC
eE
0.80 BSC
SD
0.00
SE
0.00
2. SOLDER BALL POSITION DESIGNATION PER JEP95, SECTION 3, SPP-020.
3. "e" REPRESENTS THE SOLDER BALL GRID PITCH.
4. SYMBOL "MD" IS THE BALL MATRIX SIZE IN THE "D" DIRECTION.
SYMBOL "ME" IS THE BALL MATRIX SIZE IN THE "E" DIRECTION.
N IS THE NUMBER OF POPULATED SOLDER BALL POSITIONS FOR MATRIX
SIZE MD X ME.
5. DIMENSION "b" IS MEASURED AT THE MAXIMUM BALL DIAMETER IN A
PLANE PARALLEL TO DATUM C.
6. "SD" AND "SE" ARE MEASURED WITH RESPECT TO DATUMS A AND B AND
DEFINE THE POSITION OF THE CENTER SOLDER BALL IN THE OUTER ROW.
0.35
WHEN THERE IS AN ODD NUMBER OF SOLDER BALLS IN THE OUTER ROW,
"SD" OR "SE" = 0.
WHEN THERE IS AN EVEN NUMBER OF SOLDER BALLS IN THE OUTER ROW,
"SD" = eD/2 AND "SE" = eE/2.
7. A1 CORNER TO BE IDENTIFIED BY CHAMFER, LASER OR INK MARK
METALIZED MARK, INDENTATION OR OTHER MEANS.
8. "+" INDICATES THE THEORETICAL CENTER OF DEPOPULATED SOLDER
BALLS.
001-54471 *E
Document Number: 001-52136 Rev. *S
Page 43 of 53
CYUSB301X/CYUSB201X
Figure 32. 131-ball WLCSP (5.099 × 4.695 × 0.60 mm) Package Diagram
001-62221 *C
Note Underfill is required on the board design. Contact [email protected] for details.
Document Number: 001-52136 Rev. *S
Page 44 of 53
CYUSB301X/CYUSB201X
Ordering Information
Table 20. Ordering Information
Ordering Code
USB
SRAM (kB) GPIF II Data Bus Width
Operating Temperature
Package Type
CYUSB3011-BZXC
USB 3.0
256
16-bit
0 °C to +70 °C
121-ball BGA
CYUSB3012-BZXC
USB 3.0
256
32-bit
0 °C to +70 °C
121-ball BGA
CYUSB3013-BZXC
USB 3.0
512
16-bit
0 °C to +70 °C
121-ball BGA
CYUSB3014-BZXC
USB 3.0
512
32-bit
0 °C to +70 °C
121-ball BGA
CYUSB3014-BZXI
USB 3.0
512
32-bit
–40°C to +85°C
121-ball BGA
CYUSB3014-FBXCT
USB 3.0
512
32-bit
0 °C to +70 °C
131-ball WLCSP
CYUSB3014-FBXIT
USB 3.0
512
32-bit
–40 °C to +85 °C
131-ball WLCSP
CYUSB2014-BZXC
USB 2.0
512
32-bit
0 °C to +70 °C
121-ball BGA
CYUSB2014-BZXI
USB 2.0
512
32-bit
–40 °C to +85 °C
121-ball BGA
Ordering Code Definitions
Document Number: 001-52136 Rev. *S
Page 45 of 53
CYUSB301X/CYUSB201X
Acronyms
Document Conventions
Acronym
Description
Units of Measure
DMA
direct memory access
FIFO
first in, first out
°C
degree Celsius
GPIF
general programmable interface
µA
microamperes
HNP
host negotiation protocol
µs
microseconds
I2C
inter-integrated circuit
mA
milliamperes
I2S
inter IC sound
Mbps
Megabits per second
MISO
master in, slave out
MBps
Megabytes per second
MOSI
master out, slave in
MHz
mega hertz
MMC
multimedia card
ms
milliseconds
MSC
mass storage class
ns
nanoseconds
MTP
media transfer protocol

ohms
OTG
on-the-go
pF
pico Farad
OVP
overvoltage protection
V
volts
PHY
physical layer
PLL
phase locked loop
PMIC
power management IC
PVT
process voltage temperature
RTOS
real-time operating system
SCL
serial clock line
SCLK
serial clock
SD
secure digital
SD
secure digital
SDA
serial data clock
SDIO
secure digital input / output
SLC
single-level cell
SLCS
Slave Chip Select
SLOE
Slave Output Enable
SLRD
Slave Read
SLWR
Slave Write
SPI
serial peripheral interface
SRP
session request protocol
SSN
SPI slave select (Active low)
UART
universal asynchronous receiver transmitter
UVC
USB Video Class
USB
universal serial bus
WLCSP
wafer level chip scale package
Document Number: 001-52136 Rev. *S
Symbol
Unit of Measure
Page 46 of 53
CYUSB301X/CYUSB201X
Errata
This section describes the errata for Revision C of the FX3. Details include errata trigger conditions, scope of impact, available
workaround, and silicon revision applicability. Contact your local Cypress Sales Representative if you have questions.
Part Numbers Affected
Part Number
Device Characteristics
CYUSB301x-xxxx
All Variants
CYUSB201x-xxxx
All Variants
Qualification Status
Product Status: Production
Errata Summary
The following table defines the errata applicability to available Rev. C EZ-USB FX3 SuperSpeed USB Controller family
devices.
Items
[Part Number]
Silicon Revision
1. Turning off VIO1 during Normal, Suspend, and Standby
modes causes the FX3 to stop working.
CYUSB301x-xxxx
CYUSB201x-xxxx
Rev. C, B, ES
2. USB enumeration failure in USB boot mode when FX3
is self-powered.
CYUSB301x-xxxx
CYUSB201x-xxxx
Rev. C, B, ES
3. Extra ZLP is generated by the COMMIT action in the
GPIF II state.
CYUSB301x-xxxx
CYUSB201x-xxxx
Rev. C, B, ES
4. Invalid PID Sequence in USB 2.0 ISOC data transfer.
CYUSB301x-xxxx
CYUSB201x-xxxx
Rev. C, B, ES
5. USB data transfer errors are seen when ZLP is followed
by data packet within same microframe.
CYUSB301x-xxxx
CYUSB201x-xxxx
Rev. C, B, ES
6. Bus collision is seen when the I2C block is used as a
master in the I2C Multi-master configuration.
CYUSB301x-xxxx
CYUSB201x-xxxx
Rev. C, B, ES
Fix Status
Workaround provided
Workaround provided
Workaround provided
Workaround provided
Workaround provided
Use FX3 in single-master
configuration
1. Turning off VIO1 during Normal, Suspend, and Standby modes causes the FX3 to stop working.
■Problem
Definition
Turning off the VIO1 during Normal, Suspend, and Standby modes will cause the FX3 to stop working.
■Parameters
Affected
N/A
■Trigger
Conditions
This condition is triggered when the VIO1 is turned off during Normal, Suspend, and Standby modes.
■Scope
Of Impact
FX3 stops working.
■Workaround
VIO1 must stay on during Normal, Suspend, and Standby modes.
■Fix
Status
No fix. Workaround is required.
2. USB enumeration failure in USB boot mode when FX3 is self-powered.
■Problem
Definition
FX3 device may not enumerate in USB boot mode when it is self-powered. The bootloader is designed for bus power mode. It
does not make use of the VBUS pin on the USB connector to detect the USB connection and expect that USB bus is connected
to host if it is powered. If FX3 is not already connected to the USB host when it is powered, then it enters into low-power mode
and does not wake up when connected to USB host.
■Parameters
Affected
N/A
Document Number: 001-52136 Rev. *S
Page 47 of 53
CYUSB301X/CYUSB201X
■Trigger
Conditions
This condition is triggered when FX3 is self-powered in USB boot mode.
■Scope
Of Impact
Device does not enumerate
■Workaround
Reset the device after connecting to USB host.
■Fix
Status
No fix. Workaround is required.
3. Extra ZLP is generated by the COMMIT action in the GPIF II state.
■Problem
Definition
When COMMIT action is used in a GPIF-II state without IN_DATA action then an extra Zero Length Packet (ZLP) is committed
along with the data packets.
■Parameters
Affected
N/A
■Trigger
Conditions
This condition is triggered when COMMIT action is used in a state without IN_DATA action.
■Scope
Of Impact
Extra ZLP is generated.
■Workaround
Use IN_DATA action along with COMMIT action in the same state.
■Fix
Status
No fix. Workaround is required.
4. Invalid PID Sequence in USB 2.0 ISOC data transfer.
■Problem
Definition
When the FX3 device is functioning as a high speed USB device with high bandwidth isochronous endpoints, the PID sequence
of the ISO data packets is governed solely by the isomult setting. The length of the data packet is not considered while generating
the PID sequence during each microframe. For example, even if a short packet is being sent on an endpoint with MULT set to 2;
the PID used will be DATA2
■Parameters
Affected
N/A
■Trigger
Conditions
This condition is triggered when high bandwidth ISOC transfer endpoints are used.
■Scope
Of Impact
ISOC data transfers failure.
■Workaround
This problem can be worked around by reconfiguring the endpoint with a lower isomult setting prior to sending short packets, and
then switching back to the original value.
■Fix
Status
No fix. Workaround is required.
5. USB data transfer errors are seen when ZLP is followed by data packet within same microframe.
■Problem
Definition
Some data transfer errors may be seen if a Zero Length Packet is followed very quickly (within one microframe or 125 us) by
another data packet on a burst enabled USB IN endpoint operating at super speed.
■Parameters
Affected
N/A
■Trigger
Conditions
This condition is triggered in SuperSpeed transfer with ZLPs
■Scope
Of Impact
Data failure and lower data speed.
■Workaround
The solution is to ensure that some time is allowed to elapse between a ZLP and the next data packet on burst enabled USB IN
endpoints. If this cannot be ensured at the data source, the CyU3PDmaChannelSetSuspend() API can be used to suspend the
Document Number: 001-52136 Rev. *S
Page 48 of 53
CYUSB301X/CYUSB201X
corresponding USB DMA socket on seeing the EOP condition. The channel operation can then be resumed as soon as the
suspend callback is received.
■Fix
Status
No fix. Workaround is required.
6. Bus collision is seen when the I2C block is used as a master in the I2C Multi-master configuration.
■Problem
definition
When FX3 is used as a master in the I2C multi-master configuration, there can be occasional bus collisions.
■Parameters
affected
NA
■Trigger
Conditions
This condition is triggered only when the FX3 I2C block operates in Multi-master configuration.
■Scope
Of Impact
The FX3 I2C block can transmit data when the I2C bus is not idle leading to bus collision.
■Workaround
Use FX3 as a single master.
■Fix
Status
No fix.
Document Number: 001-52136 Rev. *S
Page 49 of 53
CYUSB301X/CYUSB201X
Document History Page
Document Title: CYUSB301X/CYUSB201X, EZ-USB® FX3: SuperSpeed USB Controller
Document Number: 001-52136
Orig. of
Submission
Revision
ECN
Description of Change
Change
Date
**
2669761
VSO /
03/06/2009 New data sheet
PYRS
*A
2758370
VSO
09/01/2009 Updated the part# from CYX01XXBB to CYUSB3011-BZXI
Changed the title from “ADVANCE” to “ADVANCE INFORMATION”
In page 1, the second bullet (Flexible Host Interface), add “32-bit, 100 MHz” to
first sub bullet.
In page 1, changed the second bullet “Flexible Host Interface” to General
Programmable Interface”.
In page 1, the second bullet (Flexible Host Interface), removed "DMA Slave
Support” and "MMC Slave support with Pass through Boot" sub bullets.
In page 1, third bullet, changed "50 A with Core Power" to "60 A with Core
Power"
In page 1, fifth bullet, added "at 1 MHz"
In page 1, seventh bullet, added "up to 4MHz" to UART
In page 1, Applications Section, move “Digital Still Cameras” to second line.
In page 1, Applications Section, added “Machine Vision” and Industrial
Cameras”
Added ™ to GPIF and FX3.
In page 1, updated Logic Block Diagram.
In page 2, section of “Functional Overview”, updated the whole section.
In page 2, removed the section of “Product Interface”
In page 2, removed the section of “Processor Interface (P-Port)”
In page 2, removed the section of “USB Interface (U-Port)”
In page 2, removed the section of “Other Interfaces”
In page 2, added a section of "GPIF II"
In page 2, added a section of "CPU"
In page 2, added a section of "JTAG Interface"
In page 2, added a section of "Boot Options"
In page 2, added a section of "ReNumeration"
In page 2, added a section of "Power"
In the section of “Package”, replaced “West Bridge USB 3.0 Platform” by FX3.
In the section of “Package”, added 0.8 mm pitch in front of BGA.
Added Pin List (Table 1)
*B
2779196 VSO/PYRS 09/29/2009 Features:
Added the thrid bullet “Fully accessible 32-bit ARM9 core with 512kB of
embedded SRAM”
Added the thrid line “EZ USB™ Software and DVK for easy code development”
Table 1: Pin 74, corrected to NC - No Connect.
Changed title to EZ-USB™ FX3: SuperSpeed USB Controller
*C
2823531
OSG
12/08/2009 Added data sheet to the USB 3.0 EROS spec 001-51884. No technical
updates.
*D
3080927
OSG
11/08/2010 Changed status from Advance to Preliminary
Changed part number from CYUSB3011 to CYUSB3014
Added the following sections: Power, Digital I/Os, Digital I/Os, System-level
ESD, Electrical Specifications, AC Timing Parameters, Reset Sequence,
Package Diagram
Added DC Specifications table
Updated feature list
Updated Pin List
Added support for selectable clock input frequencies.
Updated block diagram
Updated part number
Updated package diagram
Document Number: 001-52136 Rev. *S
Page 50 of 53
CYUSB301X/CYUSB201X
Document History Page (continued)
Document Title: CYUSB301X/CYUSB201X, EZ-USB® FX3: SuperSpeed USB Controller
Document Number: 001-52136
Orig. of
Submission
Revision
ECN
Description of Change
Change
Date
*E
3204393
OSG
03/24/2011
*F
*G
*H
3219493
3235250
3217917
OSG
GSZ
OSG
04/07/2011
04/20/2011
04/06/2011
*I
*J
3305568
3369042
DSG
OSG
07/07/2011
12/06/2011
*K
*L
3534275
3649782
OSG
OSG
02/24/2012
08/16/2012
*M
3848148
OSG
12/20/2012
*N
4016006
OSG
05/31/2013
Document Number: 001-52136 Rev. *S
Updated Slave FIFO protocol and added ZLP signaling protocol
Changed GPIFII asynchronous tDO parameter
Changed Async Slave FIFO tOE parameter
Changed Async Slave FIFO tRDO parameter
Added tCOE parameter to GPIFII Sync mode timing parameters
Renamed GPIFII Sync mode tDO to tCO and tDO_ss0 to tCO_ss0
Modified description of GPIFII Sync tCO (previously tDO) parameter
Changed tAH(address hold time) parameter in Async Slave FIFO modes to be
with respect to rising edge of SLWR#/SLRD# instead of falling edge.
Correspondingly, changed the tAH number.
Removed 24 bit data bus support for GPIFII.
Minor ECN - Release to web. No content changes.
Minor updates in Features.
Updated GPIFII Synchronous Timing diagram. Added SPI Boot option.
Corrected values of R_USB2 and R_USB3. Corrected TCK and TRST#
pull-up/pull-down configuration. Minor updates to block diagrams.
Corrected Synchronous Slave FIFO tDH parameter.
Minor ECN - Correct ECN number in revision *F. No content changes.
Changed datasheet status from Preliminary to Final.
Changed tWRPE parameter to 2ns
Updated tRR and tRPW for crystal input
Added clarification regarding IOZ and IIX
Updated Sync SLave FIFO Read timing diagram
Updated SPI timing diagram
Removed tGRANULARITY parameter
Updated I2S Timing diagram and tTd parameter
Updated 121-ball BGA package diagram.
Added clarification regarding VCC in DC Specifications table
In Power Modes description, stated that VIO1 cannot be turned off at any time
if the GPIFII is used in the application
Updated Absolute Maximum Ratings
Added requirement for by-pass capacitor on U3RXVDDQ and U3TXVDDQ
Updated tPEI parameter in Async Slave FIFO timing table
Updated Sync Slave FIFO write and read timing diagrams
Updated I2C interface tVD:ACK parameter for 1MHz operation
Clarified that CTL[15] is not usable as a GPIO
Corrected typo in the block diagram.
Changed part number to CYUSB301X.
Added 256 KB range for embedded SRAM.
Updated Functional Overview, Other Interfaces, and Clocking sections.
Added Pin List for CYUSB3011 and CYUSB3013 parts.
Updated Ordering Information with new part numbers.
Updated 121-ball BGA package diagram to current revision.
Updated Features (Added 131-ball WLCSP under Package option).
Updated Pin Configurations (Added FX3 131-ball WLCSP Ball Map (Figure 7)).
Updated Pin Description (Updated Table 7).
Updated Electrical Specifications (Included Commercial Temperature Range
related information).
Updated Operating Conditions (Included Commercial Temperature Range
related information).
Updated Package Diagram (Added 131-ball WLCSP Package Diagram
(Figure 32)).
Updated Ordering Information (Updated part numbers).
Page 51 of 53
CYUSB301X/CYUSB201X
Document History Page (continued)
Document Title: CYUSB301X/CYUSB201X, EZ-USB® FX3: SuperSpeed USB Controller
Document Number: 001-52136
Orig. of
Submission
Revision
ECN
Description of Change
Change
Date
*O
4368374
RSKV
05/02/2014 Updated Package Diagram:
spec 001-62221 – Changed revision from *B to *C.
Updated to new template.
Completing Sunset Review.
*P
*Q
4474200
4668496
ANOP
DBIR
08/14/2014
02/24/2015
Added CYUSB201x MPNs, ball map, and pin list to the datasheet.
Updated Features.
Updated Logic Block Diagram.
Added related documentation hyperlink in page 1.
Added More Information.
Updated Functional Overview:
Updated Application Examples:
Updated Figure 1.
Updated Figure 2.
Updated USB Interface:
Updated description.
Removed Figure “USB Interface Signals”.
Updated Pin Configurations:
Updated Figure 6.
Updated Reset:
Updated Hard Reset:
Updated description.
Updated Pin Description:
Updated Table 7:
Updated entire table.
Modified CVDDQ power domain description.
Removed Table “CYUSB3011 and CYUSB3013 Pin List (GPIF II with 16-bit
Data Bus Width)”.
Removed Table “CYUSB2014 Pin List (GPIF II with 32-bit Data Bus Width)”.
Updated Electrical Specifications:
Updated DC Specifications:
Added ISS parameter and its details.
Updated Slave FIFO Interface:
Updated Synchronous Slave FIFO Read Sequence Description:
Updated Figure 12.
Updated Synchronous Slave FIFO Write Sequence Description:
Updated Figure 13.
Updated Table 11.
Updated AC Timing Parameters:
Added Host Processor Interface (P-Port) Timing.
Updated Acronyms.
Added Errata.
Replaced West Bridge Benicia with FX3.
*R
4703347
AMDK
03/27/2015
Updated Slave FIFO Interface:
Updated Synchronous Slave FIFO Read Sequence Description:
Updated Figure 12.
Updated Synchronous Slave FIFO Write Sequence Description:
Updated Figure 13.
Updated Table 11:
Updated minimum value of tSSD parameter.
Added tACCD, tFAD parameters and their details.
*S
5160624
AJAI
04/07/2016
Removed ISS parameter.
Added item 6 in Errata.
Document Number: 001-52136 Rev. *S
Page 52 of 53
CYUSB301X/CYUSB201X
Sales, Solutions, and Legal Information
Worldwide Sales and Design Support
Cypress maintains a worldwide network of offices, solution centers, manufacturer’s representatives, and distributors. To find the office
closest to you, visit us at Cypress Locations.
PSoC®Solutions
Products
ARM® Cortex® Microcontrollers
Automotive
cypress.com/arm
cypress.com/automotive
Clocks & Buffers
cypress.com/clocks
Interface
PSoC 1 | PSoC 3 | PSoC 4 | PSoC 5LP
Cypress Developer Community
Forums | Projects | Video | Blogs | Training | Components
cypress.com/interface
Lighting & Power Control
cypress.com/powerpsoc
Memory
cypress.com/memory
PSoC
Technical Support
cypress.com/support
cypress.com/psoc
Touch Sensing
cypress.com/touch
USB Controllers
cypress.com/usb
Wireless/RF
cypress.com/wireless
© Cypress Semiconductor Corporation 2009-2016. This document is the property of Cypress Semiconductor Corporation and its subsidiaries, including Spansion LLC ("Cypress"). This document,
including any software or firmware included or referenced in this document ("Software"), is owned by Cypress under the intellectual property laws and treaties of the United States and other countries
worldwide. Cypress reserves all rights under such laws and treaties and does not, except as specifically stated in this paragraph, grant any license under its patents, copyrights, trademarks, or other
intellectual property rights. If the Software is not accompanied by a license agreement and you do not otherwise have a written agreement with Cypress governing the use of the Software, then Cypress
hereby grants you a personal, non-exclusive, nontransferable license (without the right to sublicense) (1) under its copyright rights in the Software (a) for Software provided in source code form, to
modify and reproduce the Software solely for use with Cypress hardware products, only internally within your organization, and (b) to distribute the Software in binary code form externally to end users
(either directly or indirectly through resellers and distributors), solely for use on Cypress hardware product units, and (2) under those claims of Cypress's patents that are infringed by the Software (as
provided by Cypress, unmodified) to make, use, distribute, and import the Software solely for use with Cypress hardware products. Any other use, reproduction, modification, translation, or compilation
of the Software is prohibited.
TO THE EXTENT PERMITTED BY APPLICABLE LAW, CYPRESS MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARD TO THIS DOCUMENT OR ANY SOFTWARE
OR ACCOMPANYING HARDWARE, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. To the extent
permitted by applicable law, Cypress reserves the right to make changes to this document without further notice. Cypress does not assume any liability arising out of the application or use of any
product or circuit described in this document. Any information provided in this document, including any sample design information or programming code, is provided only for reference purposes. It is
the responsibility of the user of this document to properly design, program, and test the functionality and safety of any application made of this information and any resulting product. Cypress products
are not designed, intended, or authorized for use as critical components in systems designed or intended for the operation of weapons, weapons systems, nuclear installations, life-support devices or
systems, other medical devices or systems (including resuscitation equipment and surgical implants), pollution control or hazardous substances management, or other uses where the failure of the
device or system could cause personal injury, death, or property damage ("Unintended Uses"). A critical component is any component of a device or system whose failure to perform can be reasonably
expected to cause the failure of the device or system, or to affect its safety or effectiveness. Cypress is not liable, in whole or in part, and you shall and hereby do release Cypress from any claim,
damage, or other liability arising from or related to all Unintended Uses of Cypress products. You shall indemnify and hold Cypress harmless from and against all claims, costs, damages, and other
liabilities, including claims for personal injury or death, arising from or related to any Unintended Uses of Cypress products.
Cypress, the Cypress logo, Spansion, the Spansion logo, and combinations thereof, PSoC, CapSense, EZ-USB, F-RAM, and Traveo are trademarks or registered trademarks of Cypress in the United
States and other countries. For a more complete list of Cypress trademarks, visit cypress.com. Other names and brands may be claimed as property of their respective owners.
Document Number: 001-52136 Rev. *S
®
Revised April 7, 2016
Page 53 of 53
EZ-USB™ is a trademark and West Bridge is a registered trademark of Cypress Semiconductor Corp. All products and company names mentioned in this document may be the trademarks of their
respective holders.