95747

REVISIONS
LTR
DESCRIPTION
DATE (YR-MO-DA)
APPROVED
A
Changes IAW NOR 5962-R061-97 - cfs
96-11-21
Monica L. Poelking
B
Add device class T criteria. Editorial changes throughout. - jak
98-12-07
Monica L. Poelking
C
Correct the Total Dose Rate and update RHA levels. – LTG
99-04-28
Monica L. Poelking
REV
SHEET
REV
B
B
B
B
B
B
B
B
B
B
B
SHEET
15
16
17
18
19
20
21
22
23
24
25
REV STATUS
REV
C
B
C
B
B
C
C
C
C
B
B
B
B
B
OF SHEETS
SHEET
1
2
3
4
5
6
7
8
9
10
11
12
13
14
PMIC N/A
PREPARED BY
Larry T. Gauder
STANDARD
MICROCIRCUIT
DRAWING
CHECKED BY
Thanh V. Nguyen
THIS DRAWING IS AVAILABLE
FOR USE BY ALL
DEPARTMENTS
APPROVED BY
Monica L. Poelking
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
AMSC N/A
DRAWING APPROVAL DATE
95-10-13
REVISION LEVEL
C
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216
MICROCIRCUIT, DIGITAL, RADIATION HARDENED,
HIGH SPEED CMOS, OCTAL TRANSPARENT LATCH
WITH THREE-STATE OUTPUTS, TTL COMPATIBLE
INPUTS, MONOLITHIC SILICON
SIZE
CAGE CODE
A
67268
SHEET
DSCC FORM 2233
APR 97
DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.
1 OF
5962-95747
25
5962-E243-99
1. SCOPE
1.1 Scope. This drawing documents three product assurance class levels consisting of high reliability (device classes Q and M),
space application (device class V) and for appropriate satellite and similar applications (device class T). A choice of case outlines
and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation
Hardness Assurance (RHA) levels are reflected in the PIN. For device class T, the user is encouraged to review the manufacturer’s
Quality Management (QM) plan as part of their evaluation of these parts and their acceptability in the intended application.
1.2 PIN. The PIN is as shown in the following example:
5962
R
Federal
stock class
designator
\
95747
01
RHA
designator
(see 1.2.1)
Device
type
(see 1.2.2)
/
V
X
Device
class
designator
(see 1.2.3)
Case
outline
(see 1.2.4)
C
Lead
finish
(see 1.2.5)
\/
Drawing number
1.2.1 RHA designator. Device classes Q, T and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are
marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A
specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device.
1.2.2 Device type(s). The device type(s) identify the circuit function as follows:
Device type
Generic number
01
Circuit function
HCTS373
Radiation hardened, SOS, high speed CMOS,
octal transparent latch with three-state outputs,
TTL compatible inputs
1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows:
Device class
Device requirements documentation
M
Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN
class level B microcircuits in accordance with MIL-PRF-38535, appendix A
Q, V
Certification and qualification to MIL-PRF-38535
T
Certification and qualification to MIL-PRF-38535 with performance as specified
in the device manufacturers approved quality management plan.
1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows:
Outline letter
R
X
Descriptive designator
Terminals
Package style
CDIP2-T20
CDFP4-F20
20
20
Dual-in-line
Flat pack
1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q, T and V or MIL-PRF-38535,
appendix A for device class M.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
5962-95747
A
REVISION LEVEL
B
SHEET
2
1.3 Absolute maximum ratings. 1/ 2/ 3/
Supply voltage range (VCC).......................................................................................
DC input voltage range (VIN).....................................................................................
DC output voltage range (VOUT)................................................................................
DC input current, any one input (IIN).........................................................................
DC output current, any one output (IOUT) .................................................................
Storage temperature range (TSTG)............................................................................
Lead temperature (soldering, 10 seconds) ..............................................................
Thermal resistance, junction-to-case (θJC):
Case outline R.........................................................................................................
Case outline X.........................................................................................................
Thermal resistance, junction-to-ambient (θJA):
Case outline R.........................................................................................................
Case outline X.........................................................................................................
Junction temperature (TJ).........................................................................................
Maximum package power dissipation at TA = +125°C (PD): 4/
Case outline R.........................................................................................................
Case outline X.........................................................................................................
-0.5 V dc to +7.0 V dc
-0.5 V dc to VCC + 0.5 V dc
-0.5 V dc to VCC + 0.5 V dc
±10 mA
±25 mA
-65°C to +150°C
+265°C
24°C/W
28°C/W
72°C/W
107°C/W
+175°C
0.69 W
0.47 W
1.4 Recommended operating conditions. 2/ 3/
Supply voltage range (VCC).......................................................................................
Input voltage range (VIN) ...........................................................................................
Output voltage range (VOUT) .....................................................................................
Maximum low level input voltage (VIL).......................................................................
Minimum high level input voltage (VIH)......................................................................
Case operating temperature range (TC) ...................................................................
Maximum input rise and fall time at VCC = 4.5 V (tr, tf)..............................................
+4.5 V dc to +5.5 V dc
+0.0 V dc to VCC
+0.0 V dc to VCC
0.8 V
VCC/2
-55°C to +125°C
500 ns
1.5 Radiation features.
Maximum total dose available (dose rate = 50 – 300 rad (Si)/s)
(Device classes M,Q, or V).....................................................................................
(Device class T) ......................................................................................................
Single event phenomenon (SEP) effective
linear energy threshold (LET) no upsets (see 4.4.4.4) ..........................................
Dose rate upset (20 ns pulse) ..................................................................................
Latch-up....................................................................................................................
Dose rate survivability ...............................................................................................
1/
2/
3/
4/
5/
5
2 x 10 Rads (Si)
5
1 x 10 Rads (Si)
> 100 MeV/(cm2/mg) 5/
> 1 x 1010 Rads (Si)/s 5/
None 5/
> 1 x 1012 Rads (Si)/s 5/
Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the
maximum levels may degrade performance and affect reliability.
Unless otherwise noted, all voltages are referenced to GND.
The limits for the parameters specified herein shall apply over the full specified VCC range and case temperature range of
-55°C to +125°C unless otherwise noted.
If device power exceeds package dissipation capability, provide heat sinking or derate linearly (the derating is based on θJA) at
the following rate:
Case outline R ............................................................................................................ 13.9 mW/°C
Case outline X............................................................................................................. 9.3 mW/°C
Guaranteed by design or process but not tested.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
5962-95747
A
REVISION LEVEL
C
SHEET
3
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of
this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue
of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation.
SPECIFICATION
DEPARTMENT OF DEFENSE
MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.
STANDARDS
DEPARTMENT OF DEFENSE
MIL-STD-883 MIL-STD-973 MIL-STD-1835 -
Test Method Standard Microcircuits.
Configuration Management.
Interface Standard For Microcircuit Case Outlines.
HANDBOOKS
DEPARTMENT OF DEFENSE
MIL-HDBK-103 MIL-HDBK-780 -
List of Standard Microcircuit Drawings (SMD's).
Standard Microcircuit Drawings.
(Unless otherwise indicated, copies of the specification, standards, and handbooks are available from the Standardization
Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of
this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific
exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements for device classes Q, T and V shall be in accordance with
MIL-PRF-38535 and as specified herein or as modified in the device manufacturer's Quality Management (QM) plan. The
modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device
class M shall be in accordance with MIL-PRF-38535, appendix A and as specified herein.
3.1.1 Microcircuit die. For the requirements for microcircuit die, see appendix A to this document.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in
MIL-PRF-38535 and herein for device classes Q, T and V or MIL-PRF-38535, appendix A and herein for device class M.
3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1.
3.2.3 Truth table. The truth table shall be as specified on figure 2.
3.2.4 Logic diagram. A representative logic diagram shall be as specified on figure 3.
3.2.5 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figure 4.
3.2.6 Irradiation test connections. The irradiation test connections shall be as specified in table III.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
5962-95747
A
REVISION LEVEL
B
SHEET
4
3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical
performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full case operating
temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table IIA. The electrical tests
for each subgroup are defined in table I.
3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be marked
as listed in MIL-HDBK-103. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the
manufacturer has the option of not marking the "5962-" on the device. For RHA product using this option, the RHA designator
shall still be marked. Marking for device classes Q, T and V shall be in accordance with MIL-PRF-38535. Marking for device class
M shall be in accordance with MIL-PRF-38535, appendix A.
3.5.1 Certification/compliance mark. The certification mark for device classes Q, T and V shall be a "QML" or "Q" as required in
MIL-PRF-38535. The compliance mark for device class M shall be a "C" as required in MIL-PRF-38535, appendix A.
3.6 Certificate of compliance. For device classes Q, T and V, a certificate of compliance shall be required from a QML-38535
listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of
compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see
6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing
shall affirm that the manufacturer's product meets, for device classes Q, T and V, the requirements of MIL-PRF-38535 and herein
or for device class M, the requirements of MIL-PRF-38535, appendix A and herein.
3.7 Certificate of conformance. A certificate of conformance as required for device classes Q, T and V in
MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to
this drawing.
3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein)
involving devices acquired to this drawing is required for any change as defined in MIL-STD-973.
3.9 Verification and review for device class M. For device class M, DSCC, DSCC's agent, and the acquiring activity retain the
option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made available
onshore at the option of the reviewer.
3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit
group number 38 (see MIL-PRF-38535, appendix A).
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
5962-95747
A
REVISION LEVEL
B
SHEET
5
TABLE I. Electrical performance characteristics.
Test
Symbol
Test conditions 1/
-55°C ≤ TC ≤ +125°C
unless otherwise specified
Device
type
VCC
Group A
subgroups
Limits 2/
Min
High level output
voltage
VOH
For all inputs affecting
Output under test
VIN = 2.25 V or 0.8 V
For all other inputs
VIN = VCC or GND
IOH = -50 µA
All
M, D, P, L, R
3/
Low level output
voltage
VOL
All
M, D, P, L, R
3/
All
Input current high
IIH
All
M, D, P, L, R
3/
IIL
4.40
5.5 V
1, 2, 3
5.40
1
5.40
4.5 V
5.5 V
For input under test, VIN = 5.5 V
For all other inputs
VIN = VCC or GND
All
All
M, D, P, L, R
3/
V
0.1
1
0.1
1, 2, 3
0.1
1
0.1
1
+0.5
2, 3
+5.0
1
+5.0
1
-0.5
2, 3
-5.0
1
-5.0
5.5 V
All
For input under test, VIN = GND
For all other inputs
VIN = VCC or GND
Max
1, 2, 3
All
M, D, P, L, R
3/
Input current low
1
All
M, D, P, L, R
3/
For all inputs affecting
output under test
VIN = 2.75 V or 0.8 V
For all other inputs
VIN = VCC or GND
IOL = 50 µA
4.40
All
For all inputs affecting
output under test
VIN = 2.25 V or 0.8 V
For all other inputs
VIN = VCC or GND
IOL = 50 µA
1, 2, 3
All
For all inputs affecting
output under test
VIN = 2.75 V or 0.8 V
For all other inputs
VIN = VCC or GND
IOH = -50 µA
4.5 V
5.5 V
All
Unit
V
µA
µA
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
5962-95747
A
REVISION LEVEL
C
SHEET
6
TABLE I. Electrical performance characteristics - Continued.
Test
Symbol
Test conditions 1/
-55°C ≤ TC ≤ +125°C
unless otherwise specified
Device
type
VCC
Group A
subgroups
Limits 2/
Min
Output current high
(Source)
IOH
For all inputs affecting output
under test, VIN = 4.5 V or 0.0 V
All
4.5 V
For all other inputs
VIN = VCC or GND
VOUT = 4.1 V
Output current low
(Sink)
IOL
M, D, P, L, R
3/
All
IOZH
All
1
7.2
2, 3
6.0
1
6.0
mA
mA
1
+1.0
2, 3
+50.0
1
+50.0
1
-1.0
2, 3
-50.0
1
-50.0
1, 2, 3
1.6
1
1.6
1
40.0
2, 3
750.0
1
750.0
4
10.0
All
IOZL
µA
All
5.5 V
µA
OE = 5.5 V
For all other inputs
M, D, P, L, R
3/
∆ICC
4/
TTL input levels
For input under test
VIN = VCC - 2.1 V
For all other inputs
VIN = VCC or GND
ICC
All
All
M, D, P, L, R
3/
CIN
5.5 V
All
VIN = VCC or GND
All
M, D, P, L, R
3/
Input capacitance
-6.0
5.5 V
VIN = 0.0 V or 5.5 V
VOUT = 0.0 V
Quiescent supply
current
1
Max
OE = 5.5 V
For all other inputs
M, D, P, L, R
3/
Quiescent supply
current delta,
-6.0
All
M, D, P, L, R
3/
VIN = 0.0 V or 5.5 V
VOUT = 5.5 V
Three-state output
leakage current
low
2, 3
4.5 V
For all other inputs
Three-state output
leakage current
high
-7.2
All
For all inputs affecting output
under test, VIN = 4.5 V or 0.0 V
VIN = VCC or GND
VOUT = 0.4 V
1
Unit
5.5 V
All
VIH = 5.0 V, VIL = 0.0 V
f = 1 MHz, see 4.4.1c
All
5.0 V
mA
µA
pF
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
5962-95747
A
REVISION LEVEL
C
SHEET
7
TABLE I. Electrical performance characteristics - Continued.
Test
Symbol
Test conditions 1/
-55°C ≤ TC ≤ +125°C
unless otherwise specified
Device
type
VCC
Group A
subgroups
Limits 2/
Min
Power dissipation
capacitance
Functional test
Propagation delay
time, Dn to Qn
CPD
5/
6/
tPLH1
7/
VIH = 5.0 V, VIL = 0.0 V
f = 1 MHz, see 4.4.1c
All
VIH = 2.25 V, VIL = 0.80 V
All
See 4.4.1b
All
M, D, P, L, R 3/
CL = 50 pF
RL = 500Ω
All
5.0 V
4.5 V
See figure 4
M, D, P, L, R 3/
tPHL1
7/
CL = 50 pF
RL = 500Ω
M, D, P, L, R 3/
Propagation delay
time, LE to Qn
tPLH2
7/
CL = 50 pF
RL = 500Ω
M, D, P, L, R 3/
tPHL2
7/
CL = 50 pF
RL = 500Ω
Propagation delay
time, output enable,
OE to Qn
tPZL
7/
CL = 50 pF
RL = 500Ω
See figure 4
tPZH
7/
CL = 50 pF
RL = 500Ω
19.0
10, 11
2.0
24.0
9
2.0
24.0
9
2.0
26.0
10, 11
2.0
30.0
9
2.0
30.0
9
2.0
27.0
10, 11
2.0
30.0
9
2.0
30.0
9
2.0
30.0
10, 11
2.0
34.0
9
2.0
34.0
9
2.0
32.0
10, 11
2.0
36.0
9
2.0
36.0
9
2.0
26.0
10, 11
2.0
29.0
9
2.0
29.0
4.5 V
All
All
See figure 4
M, D, P, L, R 3/
2.0
All
All
M, D, P, L, R 3/
9
4.5 V
See figure 4
M, D, P, L, R 3/
H
All
All
57.0
L
4.5 V
See figure 4
5, 6
7
All
All
57.0
H
4.5 V
See figure 4
4
L
All
All
Max
7, 8
4.5 V
4.5 V
All
Unit
pF
ns
ns
ns
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
5962-95747
A
REVISION LEVEL
C
SHEET
8
TABLE I. Electrical performance characteristics - Continued.
Test
Symbol
Propagation delay
time, output
disable, OE to Qn
tPLZ
tPHZ
7/
Test conditions 1/
-55°C ≤ TC ≤ +125°C
unless otherwise specified
Device
type
CL = 50 pF
RL = 500Ω
See figure 4
All
M, D, P, L, R 3/
Output transition
time
Setup time, high or
low, Dn to LE
Hold time, high or
low, Dn to LE
LE pulse width,
high
tTHL,
tTLH
CL = 50 pF
RL = 500Ω
8/
See figure 4
ts
CL = 50 pF
RL = 500Ω
8/
See figure 4
th
CL = 50 pF
RL = 500Ω
8/
See figure 4
tw
CL = 50 pF
RL = 500Ω
8/
See figure 4
VCC
Group A
subgroups
Min
Max
9
2.0
22.0
10, 11
2.0
25.0
9
2.0
25.0
4.5 V
All
All
4.5 V
All
9
12.0
10, 11
18.0
4.5 V
All
9
13.0
10, 11
20.0
9
10.0
10, 11
15.0
9
16.0
10, 11
24.0
4.5 V
All
Limits 2/
4.5 V
Unit
ns
ns
ns
ns
ns
1/
Each input/output, as applicable, shall be tested at the specified temperature, for the specified limits, to the tests in table I
herein. Output terminals not designated shall be high level logic, low level logic, or open, except for the ICC and ∆ICC tests, the
output terminals shall be open. When performing the ICC and ∆ICC tests, the current meter shall be placed in the circuit such
that all current flows through the meter.
2/
For negative and positive voltage and current values, the sign designates the potential difference in reference to GND and the
direction of current flow respectively; and the absolute value of the magnitude, not the sign, is relative to the minimum and
maximum limits, as applicable, listed herein.
3/
Devices supplied to this drawing meet all levels M, D, P, L, and R of irradiation. However, this device is only tested at the "R"
level (see 1.5 herein). Pre and post irradiation values are identical unless otherwise specified in table I. When performing post
irradiation electrical measurements for any RHA level, TA = +25°C.
4/
This parameter is guaranteed, if not tested, to the limits specified in table I herein.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
5962-95747
A
REVISION LEVEL
C
SHEET
9
TABLE I. Electrical performance characteristics - Continued.
5/
Power dissipation capacitance (CPD) determines both the power consumption (PD) and current consumption (IS). Where:
PD = (CPD + CL) (VCC x VCC)f + (ICC x VCC) + (n x d x ∆ICC x VCC)
IS = (CPD + CL) VCCf + ICC + (n x d x ∆ICC)
f is the frequency of the input signal; n is the number of device inputs at TTL levels; and d is the duty cycle of the input signal.
6/
The test vectors used to verify the truth table shall, at a minimum, test all functions of each input and output. All possible
input to output logic patterns per function shall be guaranteed, if not tested, to the truth table in figure 2 herein. For VOUT
measurements, L ≤ 0.5 V and H ≥ 4.0 V.
7/
AC limits at VCC = 5.5 V are equal to limits at VCC = 4.5 V. For propagation delay tests, all paths must be tested.
8/
This parameter is guaranteed but not tested. This parameter is characterized upon initial design or process changes which
affect this characteristic.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
5962-95747
A
REVISION LEVEL
B
SHEET
10
Device type
All
Case outlines
R and X
Terminal
number
Terminal
Symbol
Terminal
number
Terminal
symbol
1
OE
11
LE
2
Q0
12
Q4
3
D0
13
D4
4
D1
14
D5
5
Q1
15
Q5
6
Q2
16
Q6
7
D2
17
D6
8
D3
18
D7
9
Q3
19
Q7
10
GND
20
VCC
FIGURE 1. Terminal connections.
Inputs
Outputs
OE
LE
Dn
Qn
L
L
L
L
H
H
H
L
L
X
H
L
l
h
X
H
L
L
H
Z
H = High voltage level
L = Low voltage level
X = Irrelevant
l = Low voltage level one set-up time prior to the high-to-low latch enable transition.
h = High voltage level one set-up time prior to the high-to-low latch enable transition.
Z = High impedance.
FIGURE 2. Truth table.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
5962-95747
A
REVISION LEVEL
B
SHEET
11
FIGURE 3. Logic diagram.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
5962-95747
A
REVISION LEVEL
B
SHEET
12
FIGURE 4. Switching waveforms and test circuit.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
5962-95747
A
REVISION LEVEL
B
SHEET
13
NOTES:
1.
2.
3.
4.
5.
When measuring tPZL and tPLZ, S1 is closed and S2 is open.
When measuring tPLH, tPHL, tPZH, and tPHZ, S1 is open and S2 is closed.
CL = 50 pF minimum or equivalent (includes test jig and probe capacitance).
RL = 500Ω or equivalent.
Input signal from pulse generator: VIN = 0.0 V to 3.0 V; PRR ≤ 10 MHz; tr ≤ 3.0 ns; tf ≤ 3.0 ns; tr and tf shall be measured
from 0.3 V to 2.7 V and from 2.7 V to 0.3 V, respectively.
FIGURE 4. Switching waveforms and test circuit - Continued.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
5962-95747
A
REVISION LEVEL
B
SHEET
14
4. QUALITY ASSURANCE PROVISIONS
4.1 Sampling and inspection. For device classes Q, and V, sampling and inspection procedures shall be in accordance with
MIL-PRF-38535 or as modified in the device manufacturer’s Quality Management (QM) plan, including screening (4.2), qualification
(4.3), and conformance inspection (4.4). The modification in the QM plan shall not affect the form, fit, or function as described
herein.
For device class T, sampling and inspection procedures shall be in accordance with MIL-PRF-38535 and the device manufacturer’s
QM plan, including screening, qualification, and conformance inspection. The performance envelope and reliability information shall
be as specified in the manufacturer’s QM plan.
For device class M, sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A.
4.2 Screening. For device classes Q and V, screening shall be in accordance with MIL-PRF-38535, and shall be conducted on
all devices prior to qualification and technology conformance inspection. For device class M, screening shall be in accordance with
method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. For device class T,
screening shall be in accordance with the device manufacturer’s Quality Management (QM) plan, and shall be conducted on all
devices prior to qualification and technology conformance inspection.
4.2.1 Additional criteria for device class M.
a.
Burn-in test, method 1015 of MIL-STD-883.
(1) Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level
control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify
the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test
method 1015.
(2) TA = +125°C, minimum.
b.
Interim and final electrical test parameters shall be as specified in table IIA herein.
4.2.2 Additional criteria for device classes Q, T and V.
a.
The burn-in test duration, test condition and test temperature, or approved alternatives shall be as specified in the device
manufacturer's QM plan in accordance with MIL-PRF-38535. The burn-in test circuit shall be maintained under document
revision level control of the device manufacturer's Technology Review Board (TRB) in accordance with
MIL-PRF-38535 and shall be made available to the acquiring or preparing activity upon request. The test circuit shall
specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test
method 1015 of MIL-STD-883.
b.
Interim and final electrical test parameters shall be as specified in table IIA herein.
c.
Additional screening for device class V beyond the requirements of device class Q shall be as specified in
MIL-PRF-38535, appendix B or as modified in the device manufacturer’s Quality Management (QM) plan.
4.3 Qualification inspection for device classes Q, T and V. Qualification inspection for device classes Q and V shall be in
accordance with MIL-PRF-38535. Qualification inspection for device class T shall be in accordance with the device manufacturer’s
Quality Management (QM) plan. Inspections to be performed shall be those specified in MIL-PRF-38535 and herein for groups A,
B, C, D, and E inspections (see 4.4.1 through 4.4.4).
4.3.1 Electrostatic discharge sensitivity (ESDS) qualification inspection . ESDS testing shall be performed in accordance with
MIL-STD-883, method 3015. ESDS testing shall be measured only for initial qualification and after process or design changes
which may affect ESDS classification.
4.4 Conformance inspection. Technology conformance inspection for classes Q and V shall be in accordance with
MIL-PRF-38535, or as specified in the QM plan, including groups A, B, C, D, and E inspections and as specified herein except
where option 2 of MIL-PRF-38535 permits alternate in-line control testing. Quality conformance inspection for device class M shall
be in accordance with MIL-PRF-38535, appendix A and as specified herein. Inspections to be performed for device class M shall
be those specified in method 5005 of MIL-STD-883 and herein for groups A, B, C, D, and E inspections (see 4.4.1 through 4.4.4).
Technology conformance inspection for class T shall be in accordance with the device manufacturer’s Quality Management (QM)
plan.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
5962-95747
A
REVISION LEVEL
B
SHEET
15
4.4.1 Group A inspection.
a.
Tests shall be as specified in table IIA herein.
b.
For device class M, subgroups 7 and 8 tests shall be sufficient to verify the truth table in figure 2 herein. For device
classes Q and V, subgroups 7 and 8 shall include verifying the functionality of the device.
c.
CIN and CPD shall be measured only for initial qualification and after process or design changes which may affect
capacitance. CIN shall be measured between the designated terminal and GND at a frequency of 1 MHz. For CIN and
CPD, tests shall be sufficient to validate the limits defined in table I herein.
TABLE IIA. Electrical test requirements.
Test requirements
Subgroups
(in accordance with
MIL-STD-883,
method 5005, table I)
Subgroups
(in accordance with
MIL-PRF-38535, table III)
Device
class M
Device
class Q
Device
class V
1, 7, 9
1, 7, 9
1, 7, 9
1, 2, 3, 7,
8, 9, 10, 11
1/
1, 2, 3, 7,
8, 9, 10, 11
1/
1, 2, 3, 7,
8, 9, 10, 11
2/ 3/
1, 2, 3, 4, 5, 6,
7, 8, 9, 10, 11
1, 2, 3, 4, 5, 6,
7, 8, 9, 10, 11
1, 2, 3, 4, 5, 6,
7, 8, 9, 10, 11
1, 2, 3, 7, 8, 9,
10, 11
1, 2, 3, 7, 8, 9,
10, 11
1, 2, 3, 7, 8, 9,
10, 11 3/
Group D end-point electrical
parameters (see 4.4)
1, 7, 9
1, 7, 9
1, 7, 9
Group E end-point electrical
parameters (see 4.4)
1, 7, 9
1, 7, 9
1, 7, 9
Interim electrical
parameters (see 4.2)
Final electrical
parameters (see 4.2)
Group A test
requirements (see 4.4)
Group C end-point electrical
parameters (see 4.4)
Device
class T
As specified in QM
plan
1/ PDA applies to subgroups 1 and 7.
2/ PDA applies to subgroups 1, 7, 9, and ∆'s.
3/ Delta limits as specified in table IIB herein shall be required where specified, and the delta
values shall be completed with reference to the zero hour electrical parameters (see table I).
TABLE IIB. Burn-in and operating life test, Delta parameters (+25°C).
Parameters 1/
Delta limits
ICC
+12 µA
IOL/IOH
-15%
IOZL/IOZH
±200 nA
1/ These parameters shall be recorded before and after the required burn-in
and life test to determine delta limits.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
5962-95747
A
REVISION LEVEL
B
SHEET
16
TABLE III. Irradiation test connections.
Open
Ground
VCC = 5 V ± 0.5 V
2, 5, 6, 9, 12, 15, 16, 19
10
1, 3, 4, 7, 8, 11, 13, 14, 17, 18, 20
NOTE: Each pin except VCC and GND will have a resistor of 47 kΩ ± 5% for irradiation testing.
4.4.2 Group C inspection. The group C inspection end-point electrical parameters shall be as specified in table IIA herein.
4.4.2.1 Additional criteria for device class M. Steady-state life test conditions, method 1005 of MIL-STD-883:
a.
Test condition A, B, C, or D. The test circuit shall be maintained by the manufacturer under document revision level control
and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs,
outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1005 of MILSTD-883.
b.
TA = +125°C, minimum.
c.
Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.
4.4.2.2 Additional criteria for device classes Q, T and V. The steady-state life test duration, test condition and test temperature,
or approved alternatives shall be as specified in the device manufacturer's QM plan in accordance with MIL-PRF-38535. The test
circuit shall be maintained under document revision level control by the device manufacturer's TRB in accordance with MIL-PRF38535 and shall be made available to the acquiring or preparing activity upon request. The test circuit shall specify the inputs,
outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in test method 1005 of MIL-STD-883.
4.4.3 Group D inspection. The group D inspection end-point electrical parameters shall be as specified in table IIA herein.
4.4.4 Group E inspection. Group E inspection is required only for parts intended to be marked as radiation hardness assured
(see 3.5 herein). RHA levels for device classes M, Q and V shall be as specified in MIL-PRF-38535 and the end-point electrical
parameters shall be as specified in table IIA herein. For device class T, the RHA requirements shall be in accordance with the Class
T Radiation Requirements of MIL-PRF-38535. The end-point electrical parameters for class T devices shall be as specified in Table
I, Group A subgroups, or as modified in the QM plan.
4.4.4.1 Total dose irradiation testing. Total dose irradiation testing shall be performed in accordance with MIL-STD-883 method
1019, condition A, and as specified herein. For device class T, the total dose requirements shall be in accordance with the class T
radiation requirements of MIL-PRF-38535 (see 1.5 herein).
4.4.4.1.1 Accelerated aging testing. Accelerated aging testing shall be performed on all devices requiring a RHA level greater
than 5k rads (Si). The post-anneal end-point electrical parameter limits shall be as specified in table I herein and shall be the preirradiation end-point electrical parameter limits at 25°C ±5°C. Testing shall be performed at initial qualification and after any design
or process changes which may affect the RHA response of the device.
4.4.4.2 Dose rate induced latchup testing. Dose rate induced latchup testing shall be performed in accordance with test method
1020 of MIL-STD-883 and as specified herein (see 1.5 herein). Tests shall be performed on devices, SEC, or approved test
structures at technology qualification and after any design or process changes which may effect the RHA capability of the process.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
5962-95747
A
REVISION LEVEL
B
SHEET
17
4.4.4.3 Dose rate upset testing. Dose rate upset testing shall be performed in accordance with test method 1021 of
MIL-STD-883 and herein (see 1.5 herein).
a.
Transient dose rate upset testing shall be performed at initial qualification and after any design or process changes which
may affect the RHA performance of the devices. Test 10 devices with 0 defects unless otherwise specified.
b.
Transient dose rate upset testing for class Q, T, and V devices shall be performed as specified by a TRB approved
radiation hardness assurance plan and MIL-PRF-38535.
4.4.4.4 Single event phenomena (SEP). When specified in the purchase order or contract SEP testing shall be required on class
T and V devices (see 1.5 herein). SEP testing shall be performed on a technology process on the Standard Evaluation Circuit
(SEC) or alternate SEP test vehicle as approved by the qualifying activity at initial qualification and after any design or process
changes which may affect the upset or latchup characteristics. The recommended test conditions for SEP are as follows:
a.
The ion beam angle of incidence shall be between normal to the die surface and 60° to the normal, inclusive (i.e. 0° ≤
angle ≤ 60°). No shadowing of the ion beam due to fixturing or package related effects is allowed.
b.
The fluence shall be ≥ 100 errors or ≥ 10 ions/cm .
c.
The flux shall be between 10 and 10 ions/cm /s. The cross-section shall be verified to be flux independent by measuring
the cross-section at two flux rates which differ by at least an order of magnitude.
d.
The particle range shall be ≥ 20 micron in silicon.
e.
The test temperature shall be +25°C and the maximum rated operating temperature ±10°C.
f.
Bias conditions shall be defined by the manufacturer for the latchup measurements.
g.
Test four devices with zero failures.
6
2
5
2
2
4.5 Methods of inspection. Methods of inspection shall be specified as follows:
4.5.1 Voltage and current. Unless otherwise specified, all voltages given are referenced to the microcircuit GND terminal.
Currents given are conventional current and positive when flowing into the referenced terminal.
5. PACKAGING
5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38535 for device classes Q,
T and V or MIL-PRF-38535, appendix A for device class M.
6. NOTES
6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications (original
equipment), design applications, and logistics purposes.
6.1.1 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractor prepared
specification or drawing.
6.1.2 Substitutability. Device class Q devices will replace device class M devices.
6.2 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated with the users of record for the
individual documents. This coordination will be accomplished in accordance with MIL-STD-973 using DD Form 1692, Engineering
Change Proposal.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
5962-95747
A
REVISION LEVEL
B
SHEET
18
6.3 Record of users. Military and industrial users should inform Defense Supply Center Columbus when a system application
requires configuration control and which SMD's are applicable to that system. DSCC will maintain a record of users and this list will
be used for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic devices (FSC
5962) should contact DSCC-VA, telephone (614) 692-0525.
6.4 Comments. Comments on this drawing should be directed to DSCC-VA , Columbus, Ohio 43216-5000, or telephone (614)
692-0674.
6.5 Abbreviations, symbols, and definitions. The abbreviations, symbols, and definitions used herein are defined in
MIL-PRF-38535 and MIL-HDBK-1331.
6.6 Sources of supply.
6.6.1 Sources of supply for device classes Q, T and V. Sources of supply for device classes Q, T and V are listed in
QML-38535. The vendors listed in QML-38535 have submitted a certificate of compliance (see 3.6 herein) to DSCC-VA and have
agreed to this drawing.
6.6.2 Approved sources of supply for device class M. Approved sources of supply for class M are listed in MIL-HDBK-103. The
vendors listed in MIL-HDBK-103 have agreed to this drawing and a certificate of compliance (see 3.6 herein) has been submitted to
and accepted by DSCC-VA.
6.7 Additional information. When applicable, a copy of the following additional data shall be maintained and available from the
device manufacturer:
a. RHA upset levels.
b. Test conditions (SEP).
c. Number of upsets (SEP).
d. Number of transients (SEP).
e. Occurrence of latchup (SEP).
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
5962-95747
A
REVISION LEVEL
B
SHEET
19
APPENDIX A
10. SCOPE
10.1 Scope. This appendix establishes minimum requirements for microcircuit die to be supplied under the Qualified
Manufacturers List (QML) Program. QML microcircuit die meeting the requirements of MIL-PRF-38535 and the manufacturers
approved QM plan for use in monolithic microcircuits, multichip modules (MCMs), hybrids, electronic modules, or devices using
chip and wire designs in accordance with MIL-PRF-38534 are specified herein. Two product assurance classes consisting of
military high reliability (device class Q) and space application (device Class V) are reflected in the Part or Identification Number
(PIN). When available a choice of Radiation Hardiness Assurance (RHA) levels are reflected in the PIN.
10.2 PIN. The PIN shall be as shown in the following example:
5962
R
Federal
Stock class
designator
95747
RHA
designator
(see 10.2.1)
01
V
9
A
Device
type
(see 10.2.2)
Device
class
designator
(see 10.2.3)
Die
code
Die
Details
(see 10.2.4)
Drawing Number
10.2.1 RHA designator. Device classes Q and V RHA identified die shall meet the MIL-PRF-38535 specified RHA levels. A
dash (-) indicates a non-RHA die.
10.2.2 Device type(s). The device type(s) shall identify the circuit function as follows:
Device type
Generic number
01
Circuit function
HCTS373
Radiation hardened, SOS,
high speed CMOS,
octal transparent latch with
three-state outputs, TTL compatible
inputs.
10.2.3 Device class designator.
Device class
Q or V
Device requirements documentation
Certification and qualification to the die requirements of MIL-PRF-38535.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
5962-95747
A
REVISION LEVEL
B
SHEET
20
APPENDIX A
10.2.4 Die Details. The die details designation shall be a unique letter which designates the die’s physical dimensions, bonding
pad location(s) and related electrical function(s), interface materials, and other assembly related information, for each product and
variant supplied to this appendix.
10.2.4.1 Die Physical dimensions.
Die Types
Figure number
01
A-1
10.2.4.2 Die Bonding pad locations and Electrical functions.
Die Types
Figure number
01
A-1
10.2.4.3 Interface Materials.
Die Types
Figure number
01
A-1
10.2.4.4 Assembly related information.
Die Types
Figure number
01
A-1
10.3 Absolute maximum ratings. See paragraph 1.3 within the body of this drawing for details.
10.4 Recommended operating conditions. See paragraph 1.4 within the body of this drawing for details.
20. APPLICABLE DOCUMENTS
20.1 Government specifications, standards, bulletin, and handbooks. Unless otherwise specified, the following specifications,
standards, bulletin, and handbook of the issue listed in that issue of the Department of Defense Index of Specifications and
Standards specified in the solicitation, form a part of this drawing to the extent specified herein.
SPECIFICATION
DEPARTMENT OF DEFENSE
MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.
STANDARDS
DEPARTMENT OF DEFENSE
MIL-STD-883 - Test Method Standard Microcircuits.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
5962-95747
A
REVISION LEVEL
B
SHEET
21
APPENDIX A
HANDBOOK
DEPARTMENT OF DEFENSE
MIL-HDBK-103 - List of Standard Microcircuit Drawings.
(Copies of the specification, standards, bulletin, and handbook required by manufacturers in connection with specific acquisition
functions should be obtained from the contracting activity or as directed by the contracting activity).
20.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of
this drawing shall take precedence.
30. REQUIREMENTS
30.1 Item Requirements. The individual item requirements for device classes Q and V shall be in accordance with
MIL-PRF-38535 and as specified herein or as modified in the device manufacturer’s Quality Management (QM) plan. The
modification in the QM plan shall not effect the form, fit or function as described herein.
30.2 Design, construction and physical dimensions. The design, construction and physical dimensions shall be as specified in
MIL-PRF-38535 and the manufacturer’s QM plan, for device classes Q and V and herein.
30.2.1 Die Physical dimensions. The die physical dimensions shall be as specified in 10.2.4.1 and on figure A-1.
30.2.2 Die bonding pad locations and electrical functions. The die bonding pad locations and electrical functions shall be as
specified in 10.2.4.2 and on figure A-1.
30.2.3 Interface materials. The interface materials for the die shall be as specified in 10.2.4.3 and on figure A-1.
30.2.4 Assembly related information. The assembly related information shall be as specified in 10.2.4.4 and figure A-1.
30.2.5 Truth table. The truth table shall be as defined within paragraph 3.2.3 of the body of this document.
30.2.6 Radiation exposure circuit. The radiation exposure circuit shall be as defined within paragraph 3.2.6 of the body of this
document.
30.3 Electrical performance characteristics and post- irradiation parameter limits. Unless otherwise specified herein, the
electrical performance characteristics and post-irradiation parameter limits are as specified in table I of the body of this document.
30.4 Electrical test requirements. The wafer probe test requirements shall include functional and parametric testing sufficient to
make the packaged die capable of meeting the electrical performance requirements in table I.
30.5 Marking. As a minimum, each unique lot of die, loaded in single or multiple stack of carriers, for shipment to a customer,
shall be identified with the wafer lot number, the certification mark, the manufacturer’s identification and the PIN listed in 10.2
herein. The certification mark shall be a “QML” or “Q” as required by MIL-PRF-38535.
30.6 Certification of compliance. For device classes Q and V, a certificate of compliance shall be required from a
QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 60.4 herein). The certificate of
compliance submitted to DSCC-VA prior to listing as an approved source of supply for this appendix shall affirm that the
manufacturer’s product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and the requirements herein.
30.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 shall
be provided with each lot of microcircuit die delivered to this drawing.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
5962-95747
A
REVISION LEVEL
B
SHEET
22
APPENDIX A
40. QUALITY ASSURANCE PROVISIONS
40.1 Sampling and inspection. For device classes Q and V, die sampling and inspection procedures shall be in accordance
with MIL-PRF-38535 or as modified in the device manufacturer’s Quality Management (QM) plan. The modifications in the QM
plan shall not effect the form, fit or function as described herein.
40.2 Screening. For device classes Q and V, screening shall be in accordance with MIL-PRF-38535, and as defined in the
manufacturer’s QM plan. As a minimum it shall consist of:
a) Wafer Lot acceptance for Class V product using the criteria defined within MIL-STD-883 TM 5007.
b) 100% wafer probe (see paragraph 30.4).
c) 100% internal visual inspection to the applicable class Q or V criteria defined within MIL-STD-883 TM2010
or the alternate procedures allowed within MIL-STD-883 TM5004.
40.3 Conformance inspection.
40.3.1 Group E inspection. Group E inspection is required only for parts intended to be identified as radiation assured (see
30.5 herein). RHA levels for device classes Q and V shall be as specified in MIL-PRF-38535. End point electrical testing of
packaged die shall be as specified in table IIA herein. Group E tests and conditions are as specified within paragraphs 4.4.4.1,
4.4.4.1.1, 4.4.4.2, 4.4.4.3, and 4.4.4.4.
50. DIE CARRIER
50.1 Die carrier requirements. The requirements for the die carrier shall be in accordance with the manufacturer’s QM plan or
as specified in the purchase order by the acquiring activity. The die carrier shall provide adequate physical, mechanical and
electrostatic protection.
60. NOTES
60.1 Intended use. Microcircuit die conforming to this drawing are intended for use in microcircuits built in accordance with
MIL-PRF-38535 or MIL-PRF-38534 for government microcircuit applications (original equipment), design applications and logistics
purposes.
60.2 Comments. Comments on this appendix should be directed to DSCC-VA, Columbus, Ohio, 43216-5000 or telephone
(614)-692-0674.
60.3 Abbreviations, symbols and definitions. The abbreviations, symbols, and definitions used herein are defined with
MIL-PRF-38535 and MIL-HDBK-1331.
60.4 Sources of Supply for device classes Q and V. Sources of supply for device classes Q and V are listed in QML-38535.
The vendors listed within QML-38535 have submitted a certificate of compliance (see 30.6 herein) to DSCC-VA and have agreed
to this drawing.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
5962-95747
A
REVISION LEVEL
B
SHEET
23
APPENDIX A
FIGURE A-1
o DIE PHYSICAL DIMENSIONS
Die Size:
Die Thickness:
•
2680 x 2740 microns.
21 +/- 2 mils.
DIE BONDING PAD LOCATIONS AND ELECTRICAL FUNCTIONS
NOTE: Pad numbers reflect terminal numbers when placed in Case Outlines R, X (see Figure 1)
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
5962-95747
A
REVISION LEVEL
B
SHEET
24
APPENDIX A
o INTERFACE MATERIALS
Top Metallization:
SiAl
11.0kA +/- 1kA
Backside Metallization
None
Glassivation
Type:
Thickness
SiO2
13.0kA +/- 2.6kA
Substrate:
Silicon on Sapphire (SOS)
o ASSEMBLY RELATED INFORMATION
Substrate Potential:
Insulator
Special assembly
instructions:
Bond pad #20 (VCC) first.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43216-5000
DSCC FORM 2234
APR 97
SIZE
5962-95747
A
REVISION LEVEL
B
SHEET
25
STANDARD MICROCIRCUIT DRAWING BULLETIN
DATE: 99-04-28
Approved sources of supply for SMD 5962-95747 are listed below for immediate acquisition information only and shall
be added to MIL-HDBK-103 and QML-38535 during the next revision. MIL-HDBK-103 and QML-38535 will be revised
to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a certificate of
compliance has been submitted to and accepted by DSCC-VA. This bulletin is superseded by the next dated revision of
MIL-HDBK-103 and QML-38535.
Standard
microcircuit drawing
PIN 1/
Vendor
CAGE
Number
Vendor
similar
PIN 2/
5962R9574701VRC
34371
HCTS373DMSR
5962R9574701VXC
34371
HCTS373KMSR
5962R9574701V9A
34371
HCTS373HMSR
5962R9574701TRC
34371
HCTS373DTR
5962R9574701TXC
34371
HCTS373KTR
1/ The lead finish shown for each PIN representing
a hermetic package is the most readily available
from the manufacturer listed for that part. If the
desired lead finish is not listed contact the vendor
to determine its availability.
2/ Caution. Do not use this number for item
acquisition. Items acquired to this number may not
satisfy the performance requirements of this drawing.
Vendor CAGE
number
34371
Vendor name
and address
Harris Semiconductor
P.O. Box 883
Melbourne, FL 32902-0883
The information contained herein is disseminated for convenience only and the
Government assumes no liability whatsoever for any inaccuracies in the
information bulletin.