93187

REVISIONS
LTR
DESCRIPTION
DATE (YR-MO-DA)
APPROVED
A
B
Added device type 10. Redrew entire document.
Corrected true dimensioning table and removed dimensions A2 and F
in figure 1. Changed dimension A min from 0.185 inches to 0.180
inches for case outlines U and Y. Changes dimension A min from
0.210 inches to 0.200 inches for case outlines T and X. Added
vendor CAGE code 88379 for device types 01 through 10. Made
editorial changes throughout.
Added case outlines M, N, 4, and 5. Redrew entire document.
Table I, changed the maximum limit for the supply current 32-bit
mode test (ICC32) from 440 to 520 for device types 05 and 06, and
from 500 to 520 for device types 07 and 08. -sld
Figure 1: For case outlines 4 and 5 changed the dimension D3 min
and max limits to 1.020 and 1.060 inches. For case outlines 4 and 5
changed dimension A min limit to .135 inches. For case outlines 4
and 5 changed dimension L min limit to .132 inches. -sld
Table I; changed the max limit for ICC32 for device types 05, 06, 07,
and 08 from 520 mA to 600 mA. Changed the max limit for ICCDR1 for
device types 05 through 10 from 10.4 mA to 11.6 mA. -sld
Added device type 11. Added vendor CAGE 0EU86 for device types
05 through 09. -sld
Figure 1; changed the maximum limit for dimension D3 from 1.060
inches to 1.086 inches for case outlines 4 and 5. -sld
Added note to paragraph 1.2.2 and table I regarding the 4 transistor
design. Added footnote 3 for case outlines U, T, X, and Y on the
bulletin page. Redrew entire document. -sld
Added device types 12 through 18. -sld
Updated drawing. -gz
95-07-07
95-10-18
K. A. Cottongim
K. A. Cottongim
96-11-20
97-09-08
K. A. Cottongim
K. A. Cottongim
98-04-06
K. A. Cottongim
98-07-13
K. A. Cottongim
99-08-27
Raymond Monnin
00-02-07
Raymond Monnin
00-11-14
Raymond Monnin
01-11-13
07-04-16
Raymond Monnin
Robert M. Heber
C
D
E
F
G
H
J
K
L
REV
SHEET
REV
L
L
L
L
L
L
L
L
L
L
L
L
SHEET
15
16
17
18
19
20
21
22
23
24
25
26
REV STATUS
REV
L
L
L
L
L
L
L
L
L
L
L
L
L
L
OF SHEETS
SHEET
1
2
3
4
5
6
7
8
9
10
11
12
13
14
PMIC N/A
PREPARED BY
Steve L. Duncan
STANDARD
MICROCIRCUIT
DRAWING
THIS DRAWING IS
AVAILABLE
FOR USE BY ALL
DEPARTMENTS
AND AGENCIES OF THE
DEPARTMENT OF DEFENSE
AMSC N/A
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
http://www.dscc.dla.mil/
CHECKED BY
Michael C. Jones
APPROVED BY
Kendall A. Cottongim
MICROCIRCUIT, HYBRID, DIGITAL, STATIC
RANDOM ACCESS MEMORY, CMOS, 128K x
32-BIT
DRAWING APPROVAL DATE
94-06-24
REVISION LEVEL
L
SIZE
CAGE CODE
A
67268
SHEET
DSCC FORM 2233
APR 97
1 OF
5962-93187
26
5962-E344-07
1. SCOPE
1.1 Scope. This drawing documents five product assurance classes as defined in paragraph 1.2.3 and MIL-PRF-38534. A
choice of case outlines and lead finishes which are available and are reflected in the Part or Identifying Number (PIN). When
available, a choice of radiation hardness assurance levels are reflected in the PIN.
1.2 PIN. The PIN shall be as shown in the following example:
5962
⏐
⏐
⏐
Federal
stock class
designator
\
⏐
⏐
⏐
RHA
designator
(see 1.2.1)
93187
01
⏐
⏐
⏐
Device
type
(see 1.2.2)
/
H
⏐
⏐
⏐
Device
class
designator
(see 1.2.3)
M
⏐
⏐
⏐
Case
outline
(see 1.2.4)
X
⏐
⏐
⏐
Lead
finish
(see 1.2.5)
\/
Drawing number
1.2.1 Radiation hardness assurance (RHA) designator. RHA marked devices shall meet the MIL-PRF-38534 specified RHA
levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device.
1.2.2 Device type(s). The device type(s) identify the circuit function as follows:
Device type 1/
01
02
03
04
05,12
06,13
07,14
08,15
09,16
10,17
11,18
Generic number
WS128K32-120HQ, ACT-S128K32-120PQ
WS128K32-100HQ, ACT-S128K32-100PQ
WS128K32-85HQ, ACT-S128K32-85PQ
WS128K32-70HQ, ACT-S128K32-70PQ
WS128K32-55HQ, ACT-S128K32-55PQ,
AS8S128K32P-55
WS128K32-45HQ, ACT-S128K32-45PQ,
AS8S128K32P-45
WS128K32-35HQ, ACT-S128K32-35PQ,
AS8S128K32P-35
WS128K32-25HQ, ACT-S128K32-25PQ,
AS8S128K32P-25
WS128K32-20HQ, ACT-S128K32-20PQ,
AS8S128K32P-20
WS128K32-17HQ, ACT-S128K32-17PQ,
AS8S128K32P-17
WS128K32-15HQ
Circuit function
Access time
SRAM, 128K x 32-bit
SRAM, 128K x 32-bit
SRAM, 128K x 32-bit
SRAM, 128K x 32-bit
SRAM, 128K x 32-bit
120 ns
100 ns
85 ns
70 ns
55 ns
SRAM, 128K x 32-bit
45 ns
SRAM, 128K x 32-bit
35 ns
SRAM, 128K x 32-bit
25 ns
SRAM, 128K x 32-bit
20 ns
SRAM, 128K x 32-bit
17 ns
SRAM, 128K x 32-bit
15 ns
_____
1/ Due to the nature of the 4 transistor design of the die in these device types, topologically pure testing is important,
particularly for high reliability applications. The device manufacturer should be consulted concerning their testing
methods and algorithms.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-93187
A
REVISION LEVEL
L
SHEET
2
1.2.3 Device class designator. This device class designator shall be a single letter identifying the product assurance level. All
levels are defined by the requirements of MIL-PRF-38534 and require QML Certification as well as qualification (Class H, K, and
E) or QML Listing (Class G and D). The product assurance levels are as follows:
Device class
Device performance documentation
K
Highest reliability class available. This level is intended for use in space
applications.
H
Standard military quality class level. This level is intended for use in applications
where non-space high reliability devices are required.
G
Reduced testing version of the standard military quality class. This level uses the
Class H screening and In-Process Inspections with a possible limited temperature
range, manufacturer specified incoming flow, and the manufacturer guarantees (but
may not test) periodic and conformance inspections (Group A, B, C and D).
E
Designates devices which are based upon one of the other classes (K, H, or G)
with exception(s) taken to the requirements of that class. These exception(s) must
be specified in the device acquisition document; therefore the acquisition document
should be reviewed to ensure that the exception(s) taken will not adversely affect
system performance.
D
Manufacturer specified quality class. Quality level is defined by the manufacturers
internal, QML certified flow. This product may have a limited temperature range.
1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: 1/
Outline letter
M
N
T
U
X
Y
4
5
Descriptive designator
See figure 1
See figure 1
See figure 1
See figure 1
See figure 1
See figure 1
See figure 1
See figure 1
Terminals
Package style
66
66
66
66
66
66
66
66
Hex-in-line, single cavity, without standoffs
Hex-in-line, single cavity, without standoffs
Hex-in-line, single cavity, with standoffs
Hex-in-line, single cavity, without standoffs
Hex-in-line, single cavity, with standoffs
Hex-in-line, single cavity, without standoffs
Hex-in-line, single cavity, with standoffs
Hex-in-line, single cavity, with standoffs
1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38534.
1.3 Absolute maximum ratings. 2/
Supply voltage range (VCC) ........................................................
Signal voltage range (any pin) ...................................................
Power dissipation (PD):
Device types 01 through 08, and 12 through 15 .....................
Device types 09, 10, 11, 16, 17, and 18 ................................
Thermal resistance junction-to-case (θJC) .................................
Storage temperature range........................................................
Lead temperature (soldering, 10 seconds).................................
-0.5 V dc to +7.0 V dc
-0.5 V dc to +7.0 V dc
2.2 W
4.4 W
6.6°C/W
-65°C to +150°C
+300°C
1/ Additional case outlines are available on Standard Microcircuit Drawing 5962-95595.
2/ Stresses above the absolute maximum ratings may cause permanent damage to the device. Extended operation at the
maximum levels may degrade performance and affect reliability.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-93187
A
REVISION LEVEL
L
SHEET
3
1.4 Recommended operating conditions.
Supply voltage range (VCC) ........................................................
Input low voltage range (VIL) ......................................................
Input high voltage range (VIH) ....................................................
Output low voltage, maximum (VOL)...........................................
Output high voltage, minimum (VOH) ..........................................
Case operating temperature range (TC) .....................................
+4.5 V dc to +5.5 V dc
-0.5 V dc to +0.8 V dc
+2.2 V dc to VCC +0.3 V dc
+0.4 V dc
+2.4 V dc
-55°C to +125°C
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATIONS
MIL-PRF-38534 - Hybrid Microcircuits, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 - Test Method Standard Microcircuits.
MIL-STD-1835 - Interface Standard for Electronic Component Case Outlines.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 - List of Standard Microcircuit Drawings.
MIL-HDBK-780 - Standard Microcircuit Drawings.
(Copies of these documents are available online at http://assist.daps.dla.mil/quicksearch/ or http://assist.daps.dla.mil or from
the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of
this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item performance requirements for device classes D, E, G, H, and K shall be in
accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 may include the performance of all tests herein or as
designated in the device manufacturer's Quality Management (QM) plan or as designated for the applicable device class. The
manufacturer may eliminate, modify or optimize the tests and inspections herein, however the performance requirements as
defined in MIL-PRF-38534 shall be met for the applicable device class. In addition, the modification in the QM plan shall not
affect the form, fit, or function of the device for the applicable device class.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in
MIL-PRF-38534 and herein.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-93187
A
REVISION LEVEL
L
SHEET
4
3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1.
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.
3.2.3 Truth table(s). The truth table(s) shall be as specified on figure 3.
3.2.4 Timing diagram(s). The timing diagram(s) shall be as specified on figures 4 and 5.
3.2.5 Block diagram. The block diagram shall be as specified on figure 6.
3.2.6 Output load circuit. The output load circuit shall be as specified on figure 7.
3.3 Electrical performance characteristics. Unless otherwise specified herein, the electrical performance characteristics are
as specified in table I and shall apply over the full specified operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical
tests for each subgroup are defined in table I.
3.5 Marking of device(s). Marking of device(s) shall be in accordance with MIL-PRF-38534. The device shall be marked with
the PIN listed in 1.2 herein. In addition, the manufacturer's vendor similar PIN may also be marked.
3.6 Data. In addition to the general performance requirements of MIL-PRF-38534, the manufacturer of the device described
herein shall maintain the electrical test data (variables format) from the initial quality conformance inspection group A lot sample,
for each device type listed herein. Also, the data should include a summary of all parameters manually tested, and for those
which, if any, are guaranteed. This data shall be maintained under document revision level control by the manufacturer and be
made available to the preparing activity (DSCC-VA) upon request.
3.7 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to supply to this
drawing. The certificate of compliance (original copy) submitted to DSCC-VA shall affirm that the manufacturer's product meets
the performance requirements of MIL-PRF-38534 and herein.
3.8 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38534 shall be provided with each lot of
microcircuits delivered to this drawing.
4. VERIFICATION
4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38534 or as
modified in the device manufacturer's Quality Management (QM) plan. The modification in the QM plan shall not affect the form,
fit, or function as described herein.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-93187
A
REVISION LEVEL
L
SHEET
5
TABLE I. Electrical performance characteristics.
Test
Symbol
Conditions 1/ 2/
-55°C ≤ TC ≤ +125°C
VSS = 0 V dc
+4.5 V dc ≤ VCC ≤ +5.5 V dc
unless otherwise specified
Group A
subgroups
Limits
Device
types
Min
Unit
Max
DC PARAMETERS
Supply current,
32-bit mode
ICC32
CS = VIL, OE = VIH,
f = 5 MHz CMOS compatible
VCC = +5.5 V dc
1,2,3
01-04
05-18
Standby current
ISB
CS = VCC, OE = VIH,
f = 5 MHz CMOS compatible
VCC = +5.5 V dc
1,2,3
01,02
2.4
03,04
5.0
120
600
05-08,
12-15
60
09-11,
16-18
80
mA
mA
Input leakage current
ILI
VCC = +5.5 V dc,
VIN = GND or VCC
1,2,3
All
10
µA
Output leakage current
ILO
CS = VIH, OE = VIH,
VOUT = GND or VCC
1,2,3
All
10
µA
Output low voltage
VOL
VCC = +4.5 V dc, IOL = +2.1
mA
1,2,3
01-07,
12-14
0.4
08-11,
15-18
0.4
VCC = +4.5 V dc, IOL = +8.0
mA
Output high voltage
VOH
VCC = +4.5 V dc, IOH = -1.0
mA
1,2,3
VCC = +4.5 V dc, IOH = -4.0
mA
01-07,
12-14
2.4
08-11,
15-18
2.4
2.0
V
V
DATA RETENTION
Data retention supply
voltage
VDR
CS ≥ VCC - 0.2 V dc
1,2,3
All
Data retention current
ICCDR1
VCC = +3.0 V dc
1,2,3
5.5
V
01-04
1.6
mA
05-11,
18
11.6
12-17
20.0
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-93187
A
REVISION LEVEL
L
SHEET
6
TABLE I. Electrical performance characteristics - Continued.
Test
Symbol
Group A
subgroups
Conditions 1/ 2/
-55°C ≤ TC ≤ +125°C
VSS = 0 V dc
+4.5 V dc ≤ VCC ≤ +5.5 V dc
unless otherwise specified
Limits
Device
types
Min
Unit
Max
CAPACITANCE
OE capacitance 3/
COE
VIN = 0 V dc, f = 1.0 MHz,
TA = +25°C
4
All
500
pF
WE 1-4 capacitance 3/
CWE
VIN = 0 V dc, f = 1.0 MHz,
TA = +25°C
4
All
20
pF
CS 1-4 capacitance 3/
CCS
VIN = 0 V dc, f = 1.0 MHz,
TA = +25°C
4
All
20
pF
D0 - D31 capacitance 3/
CI/O
VI/O =0 V dc, f = 1.0 MHz,
TA = +25°C
4
All
20
pF
A0 - A16 capacitance 3/
CAD
VIN = 0 V dc, f = 1.0 MHz,
TA = +25°C
4
All
50
pF
See 4.3.1c
7,8A,8B
All
See figure 4
9,10,11
01
02
03
04
05,12
06,13
07,14
08,15
09,16
10,17
11,18
FUNCTIONAL TESTING
Functional tests
READ CYCLE AC TIMING
Read cycle time
tRC
ns
120
100
85
70
55
45
35
25
20
17
15
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-93187
A
REVISION LEVEL
L
SHEET
7
TABLE I. Electrical performance characteristics - Continued.
Test
Symbol
Group A
subgroups
Conditions 1/ 2/
-55°C ≤ TC ≤ +125°C
VSS = 0 V dc
+4.5 V dc ≤ VCC ≤ +5.5 V dc
unless otherwise specified
Limits
Device
types
Min
Unit
Max
READ CYCLE AC TIMING - Continued.
ns
120
100
85
70
55
45
35
25
20
17
15
Address access time
tAA
See figure 4
9,10,11
01
02
03
04
05,12
06,13
07,14
08,15
09,16
10,17
11,18
Output hold from address
change
tOH
See figure 4
9,10,11
01-04
5
05-18
0
ns
Chip select access time
tACS
See figure 4
9,10,11
01
02
03
04
05,12
06,13
07,14
08,15
09,16
10,17
11,18
120
100
85
70
55
45
35
25
20
17
15
ns
Output enable to output
valid
tOE
See figure 4
9,10,11
01
02
03
04
05,12
06,13
07,14
08,15
09,16
10,11
17,18
60
50
45
35
30
25
20
15
12
10
10
ns
Chip select to output in
low impedance 3/
tCLZ
See figure 4
9,10,11
01-04
5
05-18
3
ns
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-93187
A
REVISION LEVEL
L
SHEET
8
TABLE I. Electrical performance characteristics - Continued.
Test
Symbol
Group A
subgroups
Conditions 1/ 2/
-55°C ≤ TC ≤ +125°C
VSS = 0 V dc
+4.5 V dc ≤ VCC ≤ +5.5 V dc
unless otherwise specified
Limits
Device
types
Min
Unit
Max
READ CYCLE AC TIMING - Continued.
Output enable to output in
low impedance 3/
tOLZ
See figure 4
9,10,11
01-04
5
05-18
0
ns
Chip select to output
in high impedance 3/
tCHZ
See figure 4
9,10,11
01,02
03,04
05-07
08-11
12-14
15-18
35
25
20
12
20
12
ns
Output enable to output
in high impedance 3/
tOHZ
See figure 4
9,10,11
01,02
03,04
05-07
08-11
12-14
15-18
35
25
20
12
20
12
ns
Write cycle time
tWC
See figure 5
9,10,11
01
02
03
04
05,12
06,13
07,14
08,15
09,16
10,17
11,18
120
100
85
70
55
45
35
25
20
17
15
ns
Chip select to end of write
tCW
See figure 5
9,10,11
01
02
03
04
05,12
06,13
07,14
08,15
09,16
10,17
11,18
100
80
75
60
45
30
25
25
20
15
14
ns
WRITE CYCLE AC TIMING
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-93187
A
REVISION LEVEL
L
SHEET
9
TABLE I. Electrical performance characteristics - Continued.
Test
Symbol
Group A
subgroups
Conditions 1/ 2/
-55°C ≤ TC ≤ +125°C
VSS = 0 V dc
+4.5 V dc ≤ VCC ≤ +5.5 V dc
unless otherwise specified
Limits
Device
types
Min
Unit
Max
WRITE CYCLE AC TIMING - Continued.
Address select to end of
write
tAW
See figure 5
9,10,11
01
02
03
04
05,12
06,13
07,14
08,15
09,10
16,17
11,18
100
80
75
60
45
30
25
20
15
15
14
ns
Data valid to end of write
tDW
See figure 5
9,10,11
01
02
03
04
05,06
12,13
07,14
08,15
09,16
10,11
17,18
50
40
35
30
25
25
20
15
12
10
10
ns
Address setup time
tAS
See figure 5
9,10,11
01-04
5.0
05-18
0
01
02
03
04
05,12
06,13
07,14
08,15
09,16
10,11
17,18
80
70
55
50
45
30
25
20
15
14
14
Write pulse width
tWP
See figure 5
9,10,11
ns
ns
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-93187
A
REVISION LEVEL
L
SHEET
10
TABLE I. Electrical performance characteristics - Continued.
Test
Symbol
Conditions 1/ 2/
-55°C ≤ TC ≤ +125°C
VSS = 0 V dc
+4.5 V dc ≤ VCC ≤ +5.5 V dc
unless otherwise specified
Group A
subgroups
Limits
Device
types
Min
Unit
Max
WRITE CYCLE AC TIMING - Continued.
Write to output 3/
in high impedance
tWHZ
See figure 5
9,10,11
01,02
03-06
12,13
07,14
08,15
09,16
10,11
17,18
35
25
25
20
15
12
10
10
ns
Address hold time
tAH
See figure 5
9,10,11
01-04
5
ns
05-18
0
01-04
5
05,06,
07,12,
13,14
4
08,09,
10,11,
15,16,
17,18
3
All
0
Output active from end of
write
Data hold time
tOW
tDH
See figure 5
9,10,11
See figure 5
9,10,11
ns
ns
1/
Unless otherwise specified, the AC test conditions are as follows:
Input pulse levels: VIL = 0 V and VIH = 3.0 V
Input rise and fall times: 5 nanoseconds
Input and output timing reference level: 1.5 V, ±0.5 V
Output loading: see figure 7.
2/
Due to the nature of the 4 transistor design of the die used in these device types, topologically pure testing is important,
particularly for high reliability applications. The device manufacturer should be consulted concerning their testing
methods and algorithms.
3/
Guaranteed by design, but not tested.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-93187
A
REVISION LEVEL
L
SHEET
11
Case outlines M and N.
FIGURE 1. Case outline(s).
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-93187
A
REVISION LEVEL
L
SHEET
12
Case outlines M and N - Continued.
Symbol
Millimeters
Inches
Min
Max
Min
Max
A
3.30
4.09
.130
.159
A1
0.13
0.50
.005
.020
φb
0.41
0.51
.016
.020
φb1
0.76 REF
.030 REF
φb2
1.65
1.91
.065
.075
D/E
27.02
27.58
1.064
1.086
D1/E1
25.40 BSC
1.000 BSC
D2
15.24 BSC
.600 BSC
D3
26.16
e
L
26.42
1.030
2.54 BSC
4.19
1.040
.100 BSC
4.69
.165
.185
NOTES:
1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of
measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units
shall rule.
2. Pin 1 is identified by a .070 inch (1.78 mm) square pad.
3. Pin numbers are for reference only.
FIGURE 1. Case outline(s) - Continued.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-93187
A
REVISION LEVEL
L
SHEET
13
Case outlines T, X, 4, and 5.
FIGURE 1. Case outline(s) - Continued.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-93187
A
REVISION LEVEL
L
SHEET
14
Case outlines T and X - Continued.
Symbol
Millimeters
Inches
Min
Max
Min
Max
A
5.08
6.22
.200
.245
A1
0.64
0.89
.025
.035
φb
0.41
0.51
.016
.020
φb1
1.14
1.40
.045
.055
φb2
1.65
1.91
.065
.075
D/E
29.72
30.48
1.170
1.200
D1/E1
25.40 BSC
1.000 BSC
D2
15.24 BSC
.600 BSC
D3
28.96
e
L
29.21
1.140
2.54 BSC
3.68
1.150
.100 BSC
3.94
.145
.155
NOTES:
1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of
measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units
shall rule.
2. Pin 1 is identified by a .070 inch (1.78 mm) square pad.
3. Pin numbers are for reference only.
FIGURE 1. Case outline(s) - Continued.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-93187
A
REVISION LEVEL
L
SHEET
15
Case outlines 4 and 5 - Continued.
Symbol
Millimeters
Inches
Min
Max
Min
Max
A
3.43
4.95
.135
.195
A1
0.64
0.89
.025
.035
φb
0.41
0.51
.016
.020
φb1
1.14
1.40
.045
.055
φb2
1.65
1.91
.065
.075
D/E
27.02
27.58
1.064
1.086
D1/E1
25.40 BSC
1.000 BSC
D2
15.24 BSC
.600 BSC
D3
25.91
e
L
27.58
1.020
2.54 BSC
3.35
1.086
.100 BSC
3.94
.132
.155
NOTES:
1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of
measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units
shall rule.
2. Pin 1 is identified by a .060 inch ( 1.52 mm) square pad.
3. Pin numbers are for reference only.
FIGURE 1. Case outline(s) - Continued.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-93187
A
REVISION LEVEL
L
SHEET
16
Case outlines U and Y.
FIGURE 1. Case outline(s) - Continued.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-93187
A
REVISION LEVEL
L
SHEET
17
Case outlines U and Y - Continued.
Symbol
Millimeters
Inches
Min
Max
Min
Max
A
4.57
5.84
.180
.230
A1
0.13
0.50
.005
.020
φb
0.41
0.51
.016
.020
φb1
0.76
1.52
.030
.060
φb2
1.65
1.91
.065
.075
D/E
29.72
30.48
1.170
1.200
D1/E1
25.40 BSC
1.000 BSC
D2
15.24 BSC
.600 BSC
D3
28.96
e
L
29.21
1.140
2.54 BSC
4.19
1.150
.100 BSC
4.69
.165
.185
NOTES:
1. The U.S. preferred system of measurement is the metric SI. This item was designed using inch-pound units of
measurement. In case of problems involving conflicts between the metric and inch-pound units, the inch-pound units
shall rule.
2. Pin 1 is identified by a .070 inch (1.78 mm) square pad.
3. Pin numbers are for reference only.
FIGURE 1. Case outline(s) - Continued.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-93187
A
REVISION LEVEL
L
SHEET
18
Device
types
All
Device
types
All
Device
types
All
Device
types
All
Case
outlines
M,N,T,U,X,
Y,4,5
Case
outlines
M,N,T,U,X,
Y,4,5
Case
outlines
M,N,T,U,X,
Y,4,5
Case
outlines
M,N,T,U,X,
Y,4,5
Terminal
number
Terminal
symbol
Terminal
number
Terminal
symbol
Terminal
number
Terminal
symbol
Terminal
number
Terminal
symbol
1
I/O8
18
A12
35
I/O25
52
WE 3
2
I/O9
19
VCC
36
I/O26
53
CS 3
3
I/O10
20
CS 1
37
A6
54
GND
4
A13
21
See note
38
A7
55
I/O19
5
A14
22
I/O3
39
See note
56
I/O31
6
A15
23
I/O15
40
A8
57
I/O30
7
A16
24
I/014
41
A9
58
I/O29
8
See Note
25
I/O13
42
I/O16
59
I/O28
9
I/O0
26
I/O12
43
I/O17
60
A0
10
I/O1
27
OE
44
I/O18
61
A1
11
I/O2
28
See note
45
VCC
62
A2
12
WE 2
29
WE 1
46
CS 4
63
I/O23
13
CS 2
30
I/O7
47
WE 4
64
I/O22
14
GND
31
I/O6
48
I/O27
65
I/O21
15
I/O11
32
I/O5
49
A3
66
I/O20
16
A10
33
I/O4
50
A4
17
A11
34
I/O24
51
A5
NOTE:
1. Case outlines M, T, U, and 4, pins 8, 21, 28, and 39 are no connects and for case outlines N, X, Y, and 5, pins 8, 21, 28,
and 39 are grounds.
FIGURE 2. Terminal connections.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-93187
A
REVISION LEVEL
L
SHEET
19
CS
OE
WE
Mode
Data I/O
Power
H
X
X
Standby
High Z
Standby (deselect/power down)
L
L
H
Read
Data Out
Active
L
H
H
Output disable
High Z
Active (deselect)
L
X
L
Write
Data In
Active
NOTES:
1. H = VIH = High logic level
2. L = VIL = Low logic level
3. X = Do not care (either high or low)
4. High Z = High impedance state
FIGURE 3. Truth table.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-93187
A
REVISION LEVEL
L
SHEET
20
NOTE: Guaranteed by design, but not tested.
FIGURE 4. Read cycle timing diagram.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-93187
A
REVISION LEVEL
L
SHEET
21
NOTE: Guaranteed by design, but not tested.
FIGURE 5. Write cycle timing diagram.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-93187
A
REVISION LEVEL
L
SHEET
22
FIGURE 6. Block diagram.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-93187
A
REVISION LEVEL
L
SHEET
23
Parameter
Input Pulse Level
Typ.
Unit
0 - 3.0
V
Input Rise and Fall
5
ns
Input and Output Reference Level
1.5
V
Output Load Capacitance
50
pf
NOTES:
1. VZ is programmable from -2 V to +7 V.
2. IOL and IOH are programmable from 0 to 16mA.
3. Tester impedance is ZO = 75Ω.
4. VZ is typically the midpoint of VOH and VOL.
5. IOL and IOH are adjusted to simulate a typical resistive load circuit.
6. ATE tester includes jig capacitance.
FIGURE 7. Output load circuit.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-93187
A
REVISION LEVEL
L
SHEET
24
TABLE II. Electrical test requirements.
MIL-PRF-38534 test requirements
Subgroups
(in accordance with
MIL-PRF-38534, group A
test table)
Interim electrical parameters
1,4,7,9
Final electrical parameters
1*,2,3,4,7,8A,8B,9,10,11
Group A test requirements
1,2,3,4,7,8A,8B,9,10,11
Group C end-point electrical
parameters
1,2,3,4,7,8A,8B,9,10,11
Not applicable
End-point electrical parameters
for Radiation Hardness Assurance
(RHA) devices
* PDA applies to subgroup 1.
4.2 Screening. Screening shall be in accordance with MIL-PRF-38534. The following additional criteria shall apply:
a.
b.
Burn-in test, method 1015 of MIL-STD-883.
(1)
Test condition B. The test circuit shall be maintained by the manufacturer under document revision level control and
shall be made available to either DSCC-VA or the acquiring activity upon request. Also, the test circuit shall specify
the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in
method 1015 of MIL-STD-883.
(2)
TA as specified in accordance with table I of method 1015 of MIL-STD-883.
Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter
tests prior to burn-in are optional at the discretion of the manufacturer.
4.3 Conformance and periodic inspections. Conformance inspection (CI) and periodic inspection (PI) shall be in accordance
with MIL-PRF-38534 and as specified herein.
4.3.1 Group A inspection (CI). Group A inspection shall be in accordance with MIL-PRF-38534 and as follows:
a.
Tests shall be as specified in table II herein.
b.
Subgroups 5 and 6 shall be omitted.
c.
Subgroups 7 and 8 shall include verification of the truth table on figure 3.
4.3.2 Group B inspection (PI). Group B inspection shall be in accordance with MIL-PRF-38534.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-93187
A
REVISION LEVEL
L
SHEET
25
4.3.3 Group C inspection (PI). Group C inspection shall be in accordance with MIL-PRF-38534 and as follows:
a.
End-point electrical parameters shall be as specified in table II herein.
b.
Steady-state life test, method 1005 of MIL-STD-883.
(1)
Test condition B. The test circuit shall be maintained by the manufacturer under document revision level control and
shall be made available to either DSCC-VA or the acquiring activity upon request. Also, the test circuit shall specify
the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in
method 1005 of MIL-STD-883.
(2)
TA as specified in accordance with table I of method 1005 of MIL-STD-883.
(3)
Test duration: 1,000 hours, except as permitted by method 1005 of MIL-STD-883.
4.3.4 Group D inspection (PI). Group D inspection shall be in accordance with MIL-PRF-38534.
4.3.5 Radiation Hardness Assurance (RHA) inspection. RHA inspection is not currently applicable to this drawing.
5. PACKAGING
5.1 Packaging requirements. The requirements for packaging shall be in accordance with MIL-PRF-38534.
6. NOTES
6.1 Intended use. Microcircuits conforming to this drawing are intended for use for Government microcircuit applications
(original equipment), design applications, and logistics purposes.
6.2 Replaceability. Microcircuits covered by this drawing will replace the same generic device covered by a contractorprepared specification or drawing.
6.3 Configuration control of SMD's. All proposed changes to existing SMD's will be coordinated as specified in MIL-PRF38534.
6.4 Record of users. Military and industrial users shall inform Defense Supply Center Columbus (DSCC) when a system
application requires configuration control and the applicable SMD. DSCC will maintain a record of users and this list will be used
for coordination and distribution of changes to the drawings. Users of drawings covering microelectronic devices (FSC 5962)
should contact DSCC-VA, telephone (614) 692-0544.
6.5 Comments. Comments on this drawing should be directed to DSCC-VA, Columbus, Ohio 43218-3990, or telephone (614)
692-1081.
6.6 Sources of supply. Sources of supply are listed in MIL-HDBK-103 and QML-38534. The vendors listed in MIL-HDBK-103
and QML-38534 have submitted a certificate of compliance (see 3.7 herein) to DSCC-VA and have agreed to this drawing.
STANDARD
MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS
COLUMBUS, OHIO 43218-3990
DSCC FORM 2234
APR 97
SIZE
5962-93187
A
REVISION LEVEL
L
SHEET
26
STANDARD MICROCIRCUIT DRAWING BULLETIN
DATE: 07-04-16
Approved sources of supply for SMD 5962-93187 are listed below for immediate acquisition information only and shall
be added to MIL-HDBK-103 and QML-38534 during the next revisions. MIL-HDBK-103 and QML-38534 will be
revised to include the addition or deletion of sources. The vendors listed below have agreed to this drawing and a
certificate of compliance has been submitted to and accepted by DSCC-VA. This information bulletin is superseded
by the next dated revisions of MIL-HDBK-103 and QML-38534. DSCC maintains an online database of all current
sources of supply at http://www.dscc.dla.mil/Programs/Smcr/.
Standard
microcircuit drawing
PIN 1/
5962-9318701HTA
5962-9318701HTA
5962-9318701HUA
5962-9318701HUA
5962-9318701HXA
5962-9318701HXA
5962-9318701HYA
5962-9318701HYA
5962-9318701H4A
5962-9318701H4C
5962-9318701H5A
5962-9318701H5C
5962-9318702HTA
5962-9318702HTA
5962-9318702HUA
5962-9318702HUA
5962-9318702HXA
5962-9318702HXA
5962-9318702HYA
5962-9318702HYA
5962-9318702H4A
5962-9318702H4C
5962-9318702H4A
5962-9318702H5C
5962-9318703HTA
5962-9318703HTA
5962-9318703HUA
5962-9318703HUA
5962-9318703HXA
5962-9318703HXA
5962-9318703HYA
5962-9318703HYA
5962-9318703H4A
5962-9318703H4C
5962-9318703H5A
5962-9318703H5C
Vendor
cage
number
3/
3/
3/
3/
3/
3/
3/
3/
54230
54230
54230
54230
3/
3/
3/
3/
3/
3/
3/
3/
54230
54230
54230
54230
3/
3/
3/
3/
3/
3/
3/
3/
54230
54230
54230
54230
See footnotes at end of table.
1 of 8
Vendor
similar
PIN 2/
WS128K32N-120HQ
ACT-S128K32N-120P2Q
WS128K32N-120HSQ
ACT-S128K32N-120P6Q
WS128K32-120HQ
ACT-S128K32C-120P2Q
WS128K32-120HSQ
ACT-S128K32C-120P6Q
WS128K32N-120H1Q
WS128K32N-120H1Q
WS128K32-120H1Q
WS128K32-120H1Q
WS128K32N-100HQ
ACT-S128K32N-100P2Q
WS128K32N-100HSQ
ACT-S128K32N-100P6Q
WS128K32-100HQ
ACT-S128K32C-100P2Q
WS128K32-100HSQ
ACT-S128K32C-100P6Q
WS128K32N-100H1Q
WS128K32N-100H1Q
WS128K32-100H1Q
WS128K32-100H1Q
WS128K32N-85HQ
ACT-S128K32N-085P2Q
WS128K32N-85HSQ
ACT-S128K32N-085P6Q
WS128K32-85HQ
ACT-S128K32C-085P2Q
WS128K32-85HSQ
ACT-S128K32C-085P6Q
WS128K32N-85H1Q
WS128K32N-85H1Q
WS128K32-85H1Q
WS128K32-85H1Q
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued.
DATE: 07-04-16
Standard
microcircuit drawing
PIN 1/
5962-9318704HTA
5962-9318704HTA
5962-9318704HUA
5962-9318704HUA
5962-9318704HXA
5962-9318704HXA
5962-9318704HYA
5962-9318704HYA
5962-9318704H4A
5962-9318704H4C
5962-9318704H5A
5962-9318704H5C
5962-9318705HMA
5962-9318705HNA
5962-9318705HTA
5962-9318705HTA
5962-9318705HUA
5962-9318705HUA
5962-9318705HXA
5962-9318705HXA
5962-9318705HYA
5962-9318705HYA
5962-9318705H4A
5962-9318705H4C
5962-9318705H4A
5962-9318705H4C
5962-9318705H4A
5962-9318705H5A
5962-9318705H5C
5962-9318705H5A
5962-9318705H5C
5962-9318705H5A
5962-9318706HMA
5962-9318706HNA
5962-9318706HTA
5962-9318706HTA
5962-9318706HUA
5962-9318706HUA
5962-9318706HXA
5962-9318706HXA
5962-9318706HYA
5962-9318706HYA
5962-9318706H4A
5962-9318706H4C
5962-9318706H4A
5962-9318706H4C
5962-9318706H4A
5962-9318706H5A
5962-9318706H5C
5962-9318706H5A
5962-9318706H5C
5962-9318706H5A
Vendor
CAGE
number
3/
3/
3/
3/
3/
3/
3/
3/
54230
54230
54230
54230
3/
3/
3/
3/
3/
3/
3/
3/
3/
3/
0EU86
0EU86
54230
54230
3/
0EU86
0EU86
54230
54230
3/
3/
3/
3/
3/
3/
3/
3/
3/
3/
3/
0EU86
0EU86
54230
54230
3/
0EU86
0EU86
54230
54230
3/
See footnotes at end of table.
2 of 8
Vendor
similar
PIN 2/
WS128K32N-70HQ
ACT-S128K32N-070P2Q
WS128K32N-70HSQ
ACT-S128K32N-070P6Q
WS128K32-70HQ
ACT-S128K32C-070P2Q
WS128K32-70HSQ
ACT-S128K32C-070P6Q
WS128K32N-70H1Q
WS128K32N-70H1Q
WS128K32-70H1Q
WS128K32-70H1Q
ACT-S128K32N-055P3Q
ACT-S128K32C-055P3Q
WS128K32N-55HQ
ACT-S128K32N-055P2Q
WS128K32N-55HSQ
ACT-S128K32N-055P6Q
WS128K32-55HQ
ACT-S128K32C-055P2Q
WS128K32-55HSQ
ACT-S128K32C-055P6Q
AS8S128K32PN-55/883C
AS8S128K32PN-55/883C
WS128K32N-55H1Q
WS128K32N-55H1Q
ACT-S128K32N-055P7Q
AS8S128K32P-55/883C
AS8S128K32P-55/883C
WS128K32-55H1Q
WS128K32-55H1Q
ACT-S128K32C-055P7Q
ACT-S128K32N-045P3Q
ACT-S128K32C-045P3Q
WS128K32N-45HQ
ACT-S128K32N-045P2Q
WS128K32N-45HSQ
ACT-S128K32N-045P6Q
WS128K32-45HQ
ACT-S128K32C-045P2Q
WS128K32-45HSQ
ACT-S128K32C-045P6Q
AS8S128K32PN-45/883C
AS8S128K32PN-45/883C
WS128K32N-45H1Q
WS128K32N-45H1Q
ACT-S128K32N-045P7Q
AS8S128K32P-45/883C
AS8S128K32P-45/883C
WS128K32-45H1Q
WS128K32-45H1Q
ACT-S128K32C-045P7Q
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued.
DATE: 07-04-16
Standard
microcircuit drawing
PIN 1/
5962-9318707HMA
5962-9318707HNA
5962-9318707HTA
5962-9318707HTA
5962-9318707HUA
5962-9318707HUA
5962-9318707HXA
5962-9318707HXA
5962-9318707HYA
5962-9318707HYA
5962-9318707H4A
5962-9318707H4C
5962-9318707H4A
5962-9318707H4C
5962-9318707H4A
5962-9318707H5A
5962-9318707H5C
5962-9318707H5A
5962-9318707H5C
5962-9318707H5A
5962-9318708HMA
5962-9318708HNA
5962-9318708HTA
5962-9318708HTA
5962-9318708HUA
5962-9318708HUA
5962-9318708HXA
5962-9318708HXA
5962-9318708HYA
5962-9318708HYA
5962-9318708H4A
5962-9318708H4C
5962-9318708H4A
5962-9318708H4C
5962-9318708H4A
5962-9318708H5A
5962-9318708H5C
5962-9318708H5A
5962-9318708H5C
5962-9318708H5A
Vendor
CAGE
number
3/
3/
3/
3/
3/
3/
3/
3/
3/
3/
0EU86
0EU86
54230
54230
3/
0EU86
0EU86
54230
54230
3/
3/
3/
3/
3/
3/
3/
3/
3/
3/
3/
0EU86
0EU86
54230
54230
3/
0EU86
0EU86
54230
54230
3/
See footnotes at end of table.
3 of 8
Vendor
similar
PIN 2/
ACT-S128K32N-035P3Q
ACT-S128K32C-035P3Q
WS128K32N-35HQ
ACT-S128K32N-035P2Q
WS128K32N-35HSQ
ACT-S128K32N-035P6Q
WS128K32-35HQ
ACT-S128K32C-035P2Q
WS128K32-35HSQ
ACT-S128K32C-035P6Q
AS8S128K32PN-35/883C
AS8S128K32PN-35/883C
WS128K32N-35H1Q
WS128K32N-35H1Q
ACT-S128K32N-035P7Q
AS8S128K32P-35/883C
AS8S128K32P-35/883C
WS128K32-35H1Q
WS128K32-35H1Q
ACT-S128K32C-035P7Q
ACT-S128K32N-025P3Q
ACT-S128K32C-025P3Q
WS128K32N-25HQ
ACT-S128K32N-025P2Q
WS128K32N-25HSQ
ACT-S128K32N-025P6Q
WS128K32-25HQ
ACT-S128K32C-025P2Q
WS128K32-25HSQ
ACT-S128K32C-025P6Q
AS8S128K32PN-25/883C
AS8S128K32PN-25/883C
WS128K32N-25H1Q
WS128K32N-25H1Q
ACT-S128K32N-025P7Q
AS8S128K32P-25/883C
AS8S128K32P-25/883C
WS128K32-25H1Q
WS128K32-25H1Q
ACT-S128K32C-025P7Q
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued.
DATE: 07-04-16
Standard
microcircuit drawing
PIN 1/
5962-9318709HMA
5962-9318709HNA
5962-9318709HTA
5962-9318709HTA
5962-9318709HUA
5962-9318709HUA
5962-9318709HXA
5962-9318709HXA
5962-9318709HYA
5962-9318709HYA
5962-9318709H4A
5962-9318709H4C
5962-9318709H4A
5962-9318709H4C
5962-9318709H4A
5962-9318709H5A
5962-9318709H5C
5962-9318709H5A
5962-9318709H5C
5962-9318709H5A
5962-9318710HMA
5962-9318710HNA
5962-9318710HTA
5962-9318710HTA
5962-9318710HUA
5962-9318710HUA
5962-9318710HXA
5962-9318710HXA
5962-9318710HYA
5962-9318710HYA
5962-9318710H4A
5962-9318710H4C
5962-9318710H4A
5962-9318710H4C
5962-9318710H4A
5962-9318710H5A
5962-9318710H5C
5962-9318710H5A
5962-9318710H5C
5962-9318710H5A
5962-9318711H4A
5962-9318711H4C
5962-9318711H5A
5962-9318711H5C
Vendor
CAGE
number
3/
3/
3/
3/
3/
3/
3/
3/
3/
3/
0EU86
0EU86
54230
54230
3/
0EU86
0EU86
54230
54230
3/
3/
3/
3/
3/
3/
3/
3/
3/
3/
3/
0EU86
0EU86
54230
54230
3/
0EU86
0EU86
54230
54230
3/
54230
54230
54230
54230
See footnotes at end of table.
4 of 8
Vendor
similar
PIN 2/
ACT-S128K32N-020P3Q
ACT-S128K32C-020P3Q
WS128K32N-20HQ
ACT-S128K32N-020P2Q
WS128K32N-20HSQ
ACT-S128K32N-020P6Q
WS128K32-20HQ
ACT-S128K32C-020P2Q
WS128K32-20HSQ
ACT-S128K32C-020P6Q
AS8S128K32PN-20/883C
AS8S128K32PN-20/883C
WS128K32N-20H1Q
WS128K32N-20H1Q
ACT-S128K32N-020P7Q
AS8S128K32P-20/883C
AS8S128K32P-20/883C
WS128K32-20H1Q
WS128K32-20H1Q
ACT-S128K32C-020P7Q
ACT-S128K32N-017P3Q
ACT-S128K32C-017P3Q
WS128K32N-17HQ
ACT-S128K32N-017P2Q
WS128K32N-17HSQ
ACT-S128K32N-017P6Q
WS128K32-17HQ
ACT-S128K32C-017P2Q
WS128K32-17HSQ
ACT-S128K32C-017P6Q
AS8S128K32PN-17/883C
AS8S128K32PN-17/883C
WS128K32N-17H1Q
WS128K32N-17H1Q
ACT-S128K32N-017P7Q
AS8S128K32P-17/883C
AS8S128K32P-17/883C
WS128K32-17H1Q
WS128K32-17H1Q
ACT-S128K32C-017P7Q
WS128K32N-15H1Q
WS128K32N-15H1Q
WS128K32-15H1Q
WS128K32-15H1Q
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued.
DATE: 07-04-16
Standard
microcircuit drawing
PIN 1/
5962-9318712HMA
5962-9318712HMC
5962-9318712HNA
5962-9318712HNC
5962-9318712HTA
5962-9318712HTC
5962-9318712HUA
5962-9318712HUC
5962-9318712HXA
5962-9318712HXC
5962-9318712HYA
5962-9318712HYC
5962-9318712H4A
5962-9318712H4C
5962-9318712H4A
5962-9318712H4C
5962-9318712H4A
5962-9318712H4C
5962-9318712H5A
5962-9318712H5C
5962-9318712H5A
5962-9318712H5C
5962-9318712H5A
5962-9318712H5C
5962-9318713HMA
5962-9318713HMC
5962-9318713HNA
5962-9318713HNC
5962-9318713HTA
5962-9318713HTC
5962-9318713HUA
5962-9318713HUC
5962-9318713HXA
5962-9318713HXC
5962-9318713HYA
5962-9318713HYC
5962-9318713H4A
5962-9318713H4C
5962-9318713H4A
5962-9318713H4C
5962-9318713H4A
5962-9318713H4C
5962-9318713H5A
5962-9318713H5C
5962-9318713H5A
5962-9318713H5C
5962-9318713H5A
5962-9318713H5C
Vendor
CAGE
number
Vendor
similar
PIN 2/
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
0EU86
0EU86
54230
54230
88379
88379
0EU86
0EU86
54230
54230
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
0EU86
0EU86
54230
54230
88379
88379
0EU86
0EU86
54230
54230
88379
88379
ACT-S128K32N-055P3Q-R
ACT-S128K32N-055P3Q-R
ACT-S128K32C-055P3Q-R
ACT-S128K32C-055P3Q-R
ACT-S128K32N-055P2Q-R
ACT-S128K32N-055P2Q-R
ACT-S128K32N-055P6Q-R
ACT-S128K32N-055P6Q-R
ACT-S128K32C-055P2Q-R
ACT-S128K32C-055P2Q-R
ACT-S128K32C-055P6Q-R
ACT-S128K32C-055P6Q-R
AS8S128K32PN-55/883C
AS8S128K32PN-55/883C
WS128K32NH-55H1Q
WS128K32NH-55H1Q
ACT-S128K32N-055P7Q-R
ACT-S128K32N-055P7Q-R
AS8S128K32P-55/883C
AS8S128K32P-55/883C
WS128K32H-55H1Q
WS128K32H-55H1Q
ACT-S128K32C-055P7Q-R
ACT-S128K32C-055P7Q-R
ACT-S128K32N-045P3Q-R
ACT-S128K32N-045P3Q-R
ACT-S128K32C-045P3Q-R
ACT-S128K32C-045P3Q-R
ACT-S128K32N-045P2Q-R
ACT-S128K32N-045P2Q-R
ACT-S128K32N-045P6Q-R
ACT-S128K32N-045P6Q-R
ACT-S128K32C-045P2Q-R
ACT-S128K32C-045P2Q-R
ACT-S128K32C-045P6Q-R
ACT-S128K32C-045P6Q-R
AS8S128K32PN-45/883C
AS8S128K32PN-45/883C
WS128K32NH-45H1Q
WS128K32NH-45H1Q
ACT-S128K32N-045P7Q-R
ACT-S128K32N-045P7Q-R
AS8S128K32P-45/883C
AS8S128K32P-45/883C
WS128K32H-45H1Q
WS128K32H-45H1Q
ACT-S128K32C-045P7Q-R
ACT-S128K32C-045P7Q-R
See footnotes at end of table.
5 of 8
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued.
DATE: 07-04-16
Standard
microcircuit drawing
PIN 1/
5962-9318714HMA
5962-9318714HMC
5962-9318714HNA
5962-9318714HNC
5962-9318714HTA
5962-9318714HTC
5962-9318714HUA
5962-9318714HUC
5962-9318714HXA
5962-9318714HXC
5962-9318714HYA
5962-9318714HYC
5962-9318714H4A
5962-9318714H4C
5962-9318714H4A
5962-9318714H4C
5962-9318714H4A
5962-9318714H4C
5962-9318714H5A
5962-9318714H5C
5962-9318714H5A
5962-9318714H5C
5962-9318714H5A
5962-9318714H5C
5962-9318715HMA
5962-9318715HMC
5962-9318715HNA
5962-9318715HNC
5962-9318715HTA
5962-9318715HTC
5962-9318715HUA
5962-9318715HUC
5962-9318715HXA
5962-9318715HXC
5962-9318715HYA
5962-9318715HYC
5962-9318715H4A
5962-9318715H4C
5962-9318715H4A
5962-9318715H4C
5962-9318715H4A
5962-9318715H4C
5962-9318715H5A
5962-9318715H5C
5962-9318715H5A
5962-9318715H5C
5962-9318715H5A
5962-9318715H5C
Vendor
CAGE
number
Vendor
similar
PIN 2/
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
0EU86
0EU86
54230
54230
88379
88379
0EU86
0EU86
54230
54230
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
0EU86
0EU86
54230
54230
88379
88379
0EU86
0EU86
54230
54230
88379
88379
ACT-S128K32N-035P3Q-R
ACT-S128K32N-035P3Q-R
ACT-S128K32C-035P3Q-R
ACT-S128K32C-035P3Q-R
ACT-S128K32N-035P2Q-R
ACT-S128K32N-035P2Q-R
ACT-S128K32N-035P6Q-R
ACT-S128K32N-035P6Q-R
ACT-S128K32C-035P2Q-R
ACT-S128K32C-035P2Q-R
ACT-S128K32C-035P6Q-R
ACT-S128K32C-035P6Q-R
AS8S128K32PN-35/883C
AS8S128K32PN-35/883C
WS128K32NH-35H1Q
WS128K32NH-35H1Q
ACT-S128K32N-035P7Q-R
ACT-S128K32N-035P7Q-R
AS8S128K32P-35/883C
AS8S128K32P-35/883C
WS128K32H-35H1Q
WS128K32H-35H1Q
ACT-S128K32C-035P7Q-R
ACT-S128K32C-035P7Q-R
ACT-S128K32N-025P3Q-R
ACT-S128K32N-025P3Q-R
ACT-S128K32C-025P3Q-R
ACT-S128K32C-025P3Q-R
ACT-S128K32N-025P2Q-R
ACT-S128K32N-025P2Q-R
ACT-S128K32N-025P6Q-R
ACT-S128K32N-025P6Q-R
ACT-S128K32C-025P2Q-R
ACT-S128K32C-025P2Q-R
ACT-S128K32C-025P6Q-R
ACT-S128K32C-025P6Q-R
AS8S128K32PN-25/883C
AS8S128K32PN-25/883C
WS128K32NH-25H1Q
WS128K32NH-25H1Q
ACT-S128K32N-025P7Q-R
ACT-S128K32N-025P7Q-R
AS8S128K32P-25/883C
AS8S128K32P-25/883C
WS128K32H-25H1Q
WS128K32H-25H1Q
ACT-S128K32C-025P7Q-R
ACT-S128K32C-025P7Q-R
See footnotes at end of table.
6 of 8
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued.
DATE: 07-04-16
Standard
microcircuit drawing
PIN 1/
5962-9318716HMA
5962-9318716HMC
5962-9318716HNA
5962-9318716HNC
5962-9318716HTA
5962-9318716HTC
5962-9318716HUA
5962-9318716HUC
5962-9318716HXA
5962-9318716HXC
5962-9318716HYA
5962-9318716HYC
5962-9318716H4A
5962-9318716H4C
5962-9318716H4A
5962-9318716H4C
5962-9318716H4A
5962-9318716H4C
5962-9318716H5A
5962-9318716H5C
5962-9318716H5A
5962-9318716H5C
5962-9318716H5A
5962-9318716H5C
5962-9318717HMA
5962-9318717HMC
5962-9318717HNA
5962-9318717HNC
5962-9318717HTA
5962-9318717HTC
5962-9318717HUA
5962-9318717HUC
5962-9318717HXA
5962-9318717HXC
5962-9318717HYA
5962-9318717HYC
5962-9318717H4A
5962-9318717H4C
5962-9318717H4A
5962-9318717H4C
5962-9318717H4A
5962-9318717H4C
5962-9318717H5A
5962-9318717H5C
5962-9318717H5A
5962-9318717H5C
5962-9318717H5A
5962-9318717H5C
Vendor
CAGE
number
Vendor
similar
PIN 2/
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
0EU86
0EU86
54230
54230
88379
88379
0EU86
0EU86
54230
54230
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
88379
0EU86
0EU86
54230
54230
88379
88379
0EU86
0EU86
54230
54230
88379
88379
ACT-S128K32N-020P3Q-R
ACT-S128K32N-020P3Q-R
ACT-S128K32C-020P3Q-R
ACT-S128K32C-020P3Q-R
ACT-S128K32N-020P2Q-R
ACT-S128K32N-020P2Q-R
ACT-S128K32N-020P6Q-R
ACT-S128K32N-020P6Q-R
ACT-S128K32C-020P2Q-R
ACT-S128K32C-020P2Q-R
ACT-S128K32C-020P6Q-R
ACT-S128K32C-020P6Q-R
AS8S128K32PN-20/883C
AS8S128K32PN-20/883C
WS128K32NH-20H1Q
WS128K32NH-20H1Q
ACT-S128K32N-020P7Q-R
ACT-S128K32N-020P7Q-R
AS8S128K32P-20/883C
AS8S128K32P-20/883C
WS128K32H-20H1Q
WS128K32H-20H1Q
ACT-S128K32C-020P7Q-R
ACT-S128K32C-020P7Q-R
ACT-S128K32N-017P3Q-R
ACT-S128K32N-017P3Q-R
ACT-S128K32C-017P3Q-R
ACT-S128K32C-017P3Q-R
ACT-S128K32N-017P2Q-R
ACT-S128K32N-017P2Q-R
ACT-S128K32N-017P6Q-R
ACT-S128K32N-017P6Q-R
ACT-S128K32C-017P2Q-R
ACT-S128K32C-017P2Q-R
ACT-S128K32C-017P6Q-R
ACT-S128K32C-017P6Q-R
AS8S128K32PN-17/883C
AS8S128K32PN-17/883C
WS128K32NH-17H1Q
WS128K32NH-17H1Q
ACT-S128K32N-017P7Q-R
ACT-S128K32N-017P7Q-R
AS8S128K32P-17/883C
AS8S128K32P-17/883C
WS128K32H-17H1Q
WS128K32H-17H1Q
ACT-S128K32C-017P7Q-R
ACT-S128K32C-017P7Q-R
See footnotes at end of table.
7 of 8
STANDARD MICROCIRCUIT DRAWING BULLETIN - Continued.
DATE: 07-04-16
Standard
microcircuit drawing
PIN 1/
5962-9318718H4A
5962-9318718H4C
5962-9318718H5A
5962-9318718H5C
Vendor
CAGE
number
54230
54230
54230
54230
Vendor
similar
PIN 2/
WS128K32NH-15H1Q
WS128K32NH-15H1Q
WS128K32H-15H1Q
WS128K32H-15H1Q
1/ The lead finish shown for each PIN representing a hermetic
package is the most readily available from the manufacturer
listed for that part. If the desired lead finish is not listed contact
the Vendor to determine its availability.
2/ Caution. Do not use this number for item acquisition. Items
acquired to this number may not satisfy the performance
requirements of this drawing.
3/ Not available from an approved source of supply.
Vendor CAGE
number
Vendor name
and address
0EU86
Austin Semiconductor, Incorporated
8701 Cross Park Drive
Austin, TX 78754-4566
54230
White Electronic Designs Corporation
3601 East University Drive
Phoenix, AZ 85034
88379
Aeroflex Plainview, Incorporated
35 South Service Road
Plainview, NY 11803-4101
The information contained herein is disseminated for convenience only and the
Government assumes no liability whatsoever for any inaccuracies in the
information bulletin.
8 of 8