Baumer electric Aktuator-Sensor-Interface AS-Interface module ASIA 56A4017 Art.-Code: 138226 82 • Specification 2.11 41 44,5 mounting module base • Standard addressing mode as S-slave; up to 31 modules ø 4,4 (2x) 13,3 BUS NC 38 35 (DIN rail) 44 56 bus cable 6 • Connection for four 2- or 3-wire sensors add. cable nut max. 75 • Address programming via jack NC • Profile S - 0.0.F • Power supply for sensors via bus ø 16 ø 2,8 to 6,0 • Fault diagnosis LED‘s 20 bus data voltage supply range supply current reverse polarity protection E/A configuration ID-code / ID-2 code AS-i voltage indicator / error indicator inputs supply voltage for sensors short-circuit protection with feedback total current for sensors -25...+40 °C total current for sensors +40...+70 °C polarity of the inputs input current high / low input voltage high / low input indicator general protection class temperature range / storage temperature housing material mounting EMC certificate no. 20 25,5 20 connection diagram 26,5 - 33,1 VDC ≤ 220 mA yes 0 HEX 0 HEX / F HEX green LED / red LED AS-i 15 - 30 VDC yes ≤ 200 mA ≤ 150 mA PNP ≥ 5 mA / ≤ 1,5 mA > 11 VDC / < 5 VDC yellow LED IP 65 (with EPDM cable) -25...+70 °C / -25...+85 °C PBT / PC (UL 94 V-0) DIN rail / screws refer to the AS-i brochure 60405 AS-i + - AS-i D0 . . . D3 + IN 1 + IN 2 + IN 3 + IN 4 general port assignment: D0, D1, D2, D3 input possible conductor cross-sections: sensor terminals: 0,08...2,5 mm2 max. outer cable diameter: ø 2,8...6 mm diagnosis ASI Error (green) (red) Status Description POWER OFF Address = 0 No data exchange No ASi power Address = 0 Watchdog activated, Address = 0 ok -Sensor supply overload -Sensor supply shorted ok External RESET, overload LED dark Baumer Electric AG Hummelstrasse 17 Postfach CH-8501 Frauenfeld Drawn: 10.05.04/sli Checked: 12.05.04/phw LED light LED flashing Technical specifications subject to change Tel. +41 52 728 11 22 Fax +41 52 728 11 44 Released: 12.05.04/phw Last change: 04.11.04/phw Baumer electric Actuator-Sensor-Interface AS-Interface module ASIA 56A4022 Art.-Code: 147626 82 • Specification 2.11 41 44,5 mounting module base • Extended addressing mode as A/B-Slave; up to 62 modules ø 4,4 (2x) 13,3 BUS NC 38 35 (DIN rail) 44 56 bus cable 6 • Connection for four 2- or 3-wire sensors add. cable nut max. 75 • Address programming via jack NC • Profile S - 0.A.0 • Power supply for sensors via bus ø 16 ø 2,8 to 6,0 • Fault diagnosis LED‘s 20 bus data voltage supply range supply current reverse polarity protection E/A configuration ID-code / ID-2 code AS-i voltage indicator / error indicator inputs supply voltage for sensors short-circuit protection with feedback total current for sensors -25...+40 °C total current for sensors +40...+70 °C polarity of the inputs input current high / low input voltage high / low input indicator general protection class temperature range / storage temperature housing material mounting EMC certificate no. 20 25,5 20 connection diagram 26,5 - 33,1 VDC ≤ 220 mA yes 0 HEX A HEX / 0 HEX green LED / red LED AS-i 15 - 30 VDC yes ≤ 200 mA ≤ 150 mA PNP ≥ 5 mA / ≤ 1,5 mA > 11 VDC / < 5 VDC yellow LED IP 65 (with EPDM cable) -25...+70 °C / -25...+85 °C PBT / PC (UL 94 V-0) DIN rail / screws refer to the AS-i brochure 60402 AS-i + - AS-i D0 . . . D3 + IN 1 + IN 2 + IN 3 + IN 4 general port assignment: D0, D1, D2, D3 input possible conductor cross-sections: sensor terminals: 0,08...2,5 mm2 max. outer cable diameter: ø 2,8...6 mm diagnosis ASI Error (green) (red) Status Description POWER OFF Address = 0 No data exchange No ASi power Address = 0 Watchdog activated, Address = 0 ok -Sensor supply overload -Sensor supply shorted ok External RESET, overload LED dark Baumer Electric AG Hummelstrasse 17 Postfach CH-8501 Frauenfeld Drawn: 27.01.04/bad Checked: 10.05.04/ LED light LED flashing Technical specifications subject to change Tel. +41 52 728 11 22 Fax +41 52 728 11 44 Released: 10.05.04/ Last change: 04.11.04/phw