Bulletin I2164 rev. A 10/04 SAFEIR Series 70TPS.. PHASE CONTROL SCR VT < 1.4V @ 100A ITSM = 1400A VRRM = 1200, 1600V Description/ Features The 70TPS... SAFEIR series of silicon controlled rectifiers are specifically designed for high and medium power switching and phase control applications. Typical applications are in input rectification (soft start) or AC-Switches or high current crow-bar as well as others phase-control circuits. These products are designed to be used with International Rectifier input diodes, switches and output rectifiers which are available in identical package outlines. Major Ratings and Characteristics Characteristics IT(AV) Sinusoidal Package Outline 70TPS.. Units 70 A waveform IRMS (*) 75 A VRRM/ VDRM Range 1200, 1600 V 1400 A 1.4 V dv/dt 500 V/µs di/dt 150 A/µs - 40 to 125 °C ITSM VT @ 100 A, TJ = 25°C TJ Super-247 (*) Lead current limitation www.irf.com 1 70TPS.. SAFEIR Series Bulletin I2164 Rev. A 10/04 Voltage Ratings VRRM/ VDRM, max. repetitive peak and off-state voltage VRSM , maximum non repetitive peak reverse voltage IRRM/ IDRM 125°C V V mA 70TPS12 1200 1300 15 70TPS16 1600 1700 Part Number Absolute Maximum Ratings Parameters IT(AV) Max. Average On-state Current IT(RMS) Max. Continuous RMS 70TPS.. Units 70 A 75 Conditions @ TC = 82° C, 180° conduction half sine wave Lead current limitation On-state Current As AC switch ITSM I2t Max. Peak One Cycle Non-Repetitive 1200 Surge Current 1400 Max. I 2t for Fusing 7200 A A2s 10200 2 I √t 2 Max. I √t for Fusing VT(TO)1 Low Level Value of Threshold 10ms Sine pulse, rated VRRM applied Initial 10ms Sine pulse, no voltage reapplied TJ = TJ max. 10ms Sine pulse, rated VRRM applied 10ms Sine pulse, no voltage reapplied 102000 2 A √s t = 0.1 to 10ms, no voltage reapplied 0.916 V TJ = 125°C Voltage VT(TO)2 High Level Value of Threshold 1.21 Voltage rt1 Low Level Value of On-state 4.138 mΩ Slope Resistance rt2 High Level Value of On-state 3.43 Slope Resistance VTM Max. Peak On-state Voltage 1.4 V di/dt Max. Rate of Rise of Turned-on Current 150 A/µs TJ = 25°C IH Max. Holding Current 200 mA TJ = 25°C IL Max. Latching Current 400 IRRM / Max. Reverse and Direct 1.0 IDRM Leakage Current 15 dv/dt Max. Rate of Rise 500 2 mA @ 100A, TJ = 25°C TJ = 25°C TJ = 125°C V/µs VR = rated V RRM/ VDRM TJ = 125°C www.irf.com 70TPS.. SAFEIR Series Bulletin I2164 Rev. A 10/04 Triggering Parameters Conditions 70TPS.. Units PGM Max. peak Gate Power 10 W PG(AV) Max. average Gate Power 2.5 IGM 2.5 A - V GM Max. peak negative Gate Voltage 10 V VGT Max. required DC Gate Voltage 4.0 TJ = - 40°C Anode supply = 6V to trigger 1.5 TJ = 25°C resistive load 1.1 TJ = 125°C IGT Max. peak Gate Current t = 30µs Max. required DC Gate Current 270 mA TJ = - 40°C to trigger 100 V GD Max. DC Gate Voltage not to trigger 0.25 V IGD Max. DC Gate Current not to trigger 6 mA 70TPS.. Units °C TJ = 25°C 80 TJ = 125°C TJ = 125°C, V DRM = rated value Thermal-Mechanical Specifications Parameters TJ Max. Junction Temperature Range - 40 to 125 Tstg Max. Storage Temperature Range - 40 to 150 RthJC Max. Thermal Resistance Junction 0.27 °C/W Conditions DC operation to Case RthJA Max. Thermal Resistance Junction 40 to Ambient RthCS Max. Thermal Resistance Case 0.2 Mounting surface, smooth and greased to Heatsink wt Approximate Weight T Mounting Torque 6 (0.21) g (oz.) Min. 6 (5) Kg-cm Max. 12 (10) (lbf-in) Case Style Super-247 ∆R Conduction (per Junction) (The following table shows the increment of thermal resistance RthJC when devices operate at different conduction angles than DC) Device 70TPS Sine half wave conduction Rect. wave conduction 180o 120o 90o 60o 30o 180 o 120 o 90o 60o 30o 0.078 0.092 0.117 0.172 0.302 0.053 0.092 0.125 0.180 0.306 www.irf.com Units °C/W 3 70TPS.. SAFEIR Series 130 70TPS.. Series RthJC (DC) = 0.27 ˚C/W 120 110 Conduction Angle 30˚ 100 60˚ 90˚ 90 120˚ 180˚ 80 70 0 10 20 30 40 50 60 70 80 Maximum Allowable Case temperature (°C) Maximum Allowable Case temperature (°C) Bulletin I2164 Rev. A 10/04 130 70TPS.. Series RthJC (DC) = 0.27 ˚C/W 120 DC 110 Conduction Period 100 180˚ 90 80 30˚ 120 100 80 RMS Limit 60 40 Conduction Angle 20 70TPS.. Series Tj = 125˚C 0 0 10 20 30 40 50 60 70 0 At Any Rated Load Condition And With Rated Vrrm Applied Following Surge. Initial Tj = 125˚C @ 60 Hz 0.0083 s @ 50 Hz 0.0100 s 1200 1100 1000 900 800 700 600 70TPS.. Series 500 1 10 100 Number Of Equal Amplitude Half Cycle Current Pulses (N) Fig. 5 - Maximum Non-Repetitive Surge Current 4 10 20 30 40 50 60 70 80 90 150 180˚ 120˚ 90˚ 60˚ 30˚ 120 90 DC RMS Limit 60 Conduction Period 30 70TPS.. Series Tj = 125˚C 0 0 15 30 45 60 75 Average On-state Current (A) Fig. 4 - On-state Power Loss Characteristics Peak Half Sine Wave On-state Current (A) Peak Half Sine Wave On-state Current (A) Average On-state Current (A) Fig. 3 - On-state Power Loss Characteristics 1300 120˚ Average On-state Current (A) Fig. 2 - Current Rating Characteristics Maximum Average On-state Power Loss (W) Maximum Average On-state Power Loss (W) 180˚ 120˚ 90˚ 60˚ 30˚ 90˚ 60 Average On-state Current (A) Fig. 1 - Current Rating Characteristics 140 60˚ 70 1500 Maximum Non Repetitive Surge Current Versus Pulse Train Duration. Control Of Conduction May Not Be Maintained. 1300 Initial Tj = 125˚C No Voltage Reapplied 1200 Rated Vrrm Reapplied 1400 1100 1000 900 800 700 600 70TPS.. Series 500 0.01 0.1 1 Pulse Train Duration (s) Fig. 6 - Maximum Non-Repetitive Surge Current www.irf.com 70TPS.. SAFEIR Series Bulletin I2164 Rev. A 10/04 Instantaneous On-state Current (A) 1000 Tj = 125˚C 100 10 Tj = 25˚C 70TPS.. Series 1 0.5 1 1.5 2 2.5 3 3.5 Instantaneous On-state Voltage (A) Fig. 7 - On-state Voltage Drop Characteristics 10 Rectangular gate pulse a)Recommended load line for rated di/dt: 20 V, 30 ohms tr = 0.5 µs, tp >= 6 µs b)Recommended load line for <= 30% rated di/dt: 20 V, 65 ohms tr = 1 µs, tp >= 6 µs (a) IGD TJ = 25 ˚C VGD TJ = -40 ˚C 1 0.1 0.001 Transient Thermal Impedance Z thJC (°C/W) (1) PGM = 100 W, tp = 500 µs (2) PGM = 50 W, tp = 1 ms (3) PGM = 20 W, tp = 25 ms (4) PGM = 10 W, tp = 5 ms (b) TJ = 125 ˚C Instantaneous Gate Voltage (V) 100 70TPS.. Series 0.01 (4) (3) (2) (1) Frequency Limited by PG(AV) 0.1 1 10 Instantaneous Gate Current (A) Fig. 8 - GateCharacteristics 100 1000 1 Steady State Value (DC Operation) 0.1 D = 0.50 D = 0.33 D = 0.25 D = 0.17 D = 0.08 Single Pulse 70TPS.. Series 0.01 0.0001 0.001 0.01 0.1 Square Wave Pulse Duration (s) 1 10 Fig. 9 - Thermal Impedance ZthJC Characteristics www.irf.com 5 70TPS.. SAFEIR Series Bulletin I2164 Rev. A 10/04 Outline Table 0.13 [.005] 16.10 [.632] 15.10 [.595] 2X R 5.50 [.216] 4.50 [.178] A 0.25 [.010] B A 13.90 [.547] 13.30 [.524] 2.15 [.084] 1.45 [.058] 1.30 [.051] 0.70 [.028] 16.10 [.633] 15.50 [.611] 4 20.80 [.818] 19.80 [.780] 4 C 1 3 2 B 14.80 [.582] 13.80 [.544] Ø 1.60 [.063] MAX. 4.25 [.167] 3.85 [.152] 3X 3X 5.45 [.215] 2X 0.25 [.010] E 1.30 [.051] 1.10 [.044] 2.35 [.092] 1.65 [.065] SECTION E-E NOTES: 1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994. 2. DIMENSIONS ARE SHOWN IN MILLIMETERS [INCHES] 3. CONTROLLING DIMENSION: MILLIMETER 4. OUTLINE CONFORMS TO JEDEC OUTLINE TO-274AA B A E LEAD ASSIGNMENTS IGBT MOSFET 1 - GATE 2 - DRAIN 3 - SOURCE 4 - DRAIN 1 - GATE 2 - COLLECTOR 3 - EMITTER 4 - COLLECTOR Dimensions in millimeters and inches NOTE:parts are designed for clip mounting to heatsinks; mounting requirements and methods are discussed in AN-997 Ordering Information Table Device Code 70 T P S 16 1 2 3 4 5 1 - Current Rating 2 - Circuit Configuration: 2 (A) 1 (K) (G) 3 T = Thyristor 3 - Package: P = Super-247 6 4 - 5 - Type of Silicon: S = Standard Recovery Rectifier 12 = 1200V Voltage code: Code x 100 = VRRM 16 = 1600V www.irf.com 70TPS.. SAFEIR Series Bulletin I2164 Rev. A 10/04 Data and specifications subject to change without notice. This product has been designed for Industrial Level. Qualification Standards can be found on IR's Web site. IR WORLD HEADQUARTERS: 233 Kansas St., El Segundo, California 90245, USA Tel: (310) 252-7105 TAC Fax: (310) 252-7309 Visit us at www.irf.com for sales contact information. 10/04 www.irf.com 7