PHILIPS PCF8583P

INTEGRATED CIRCUITS
DATA SHEET
PCF8583
Clock/calendar with 240 × 8-bit
RAM
Product specification
Supersedes data of 1997 Mar 28
File under Integrated Circuits, IC12
1997 Jul 15
Philips Semiconductors
Product specification
Clock/calendar with 240 × 8-bit RAM
CONTENTS
1
FEATURES
2
GENERAL DESCRIPTION
3
QUICK REFERENCE DATA
4
ORDERING INFORMATION
5
BLOCK DIAGRAM
6
PINNING
7
FUNCTIONAL DESCRIPTION
7.1
7.2
7.3
7.4
7.5
7.6
7.7
7.8
7.9
7.10
7.11
Counter function modes
Alarm function modes
Control/status register
Counter registers
Alarm control register
Alarm registers
Timer
Event counter mode
Interrupt output
Oscillator and divider
Initialization
8
CHARACTERISTICS OF THE I2C-BUS
8.1
8.2
8.3
8.4
Bit transfer
Start and stop conditions
System configuration
Acknowledge
9
I2C-BUS PROTOCOL
9.1
9.2
Addressing
Clock/calendar READ/WRITE cycles
1997 Jul 15
2
PCF8583
10
LIMITING VALUES
11
HANDLING
12
DC CHARACTERISTICS
13
AC CHARACTERISTICS
14
APPLICATION INFORMATION
14.1
14.1.1
14.1.2
14.1.3
Quartz frequency adjustment
Method 1: fixed osci capacitor
Method 2: OSCI Trimmer
Method 3:
15
PACKAGE OUTLINES
16
SOLDERING
16.1
16.2
16.2.1
16.2.2
16.3
16.3.1
16.3.2
16.3.3
Introduction
DIP
Soldering by dipping or by wave
Repairing soldered joints
SO
Reflow soldering
Wave soldering
Repairing soldered joints
17
DEFINITIONS
18
LIFE SUPPORT APPLICATIONS
19
PURCHASE OF PHILIPS I2C COMPONENTS
Philips Semiconductors
Product specification
Clock/calendar with 240 × 8-bit RAM
1
•
PCF8583
2
FEATURES
I2C-bus
GENERAL DESCRIPTION
The PCF8583 is a clock/calendar circuit based on a
2048-bit static CMOS RAM organized as 256 words by
8 bits. Addresses and data are transferred serially via the
two-line bidirectional I2C-bus. The built-in word address
register is incremented automatically after each written or
read data byte. Address pin A0 is used for programming
the hardware address, allowing the connection of two
devices to the bus without additional hardware.
interface operating supply voltage: 2.5 V to 6 V
• Clock operating supply voltage (0 to +70 °C):
1.0 V to 6.0 V
• 240 × 8-bit low-voltage RAM
• Data retention voltage: 1.0 V to 6 V
• Operating current (at fSCL = 0 Hz): max. 50 µA
• Clock function with four year calendar
The built-in 32.768 kHz oscillator circuit and the first
8 bytes of the RAM are used for the clock/calendar and
counter functions. The next 8 bytes may be programmed
as alarm registers or used as free RAM space.
The remaining 240 bytes are free RAM locations.
• Universal timer with alarm and overflow indication
• 24 or 12 hour format
• 32.768 kHz or 50 Hz time base
• Serial input/output bus (I2C)
• Automatic word address incrementing
• Programmable alarm, timer and interrupt function
• Slave address:
– READ: A1 or A3
– WRITE: A0 or A2.
3
QUICK REFERENCE DATA
SYMBOL
VDD
PARAMETER
supply voltage operating mode
IDD
supply current operating mode
IDDO
supply current clock mode
CONDITION
MIN.
TYP.
MAX.
UNIT
2.5
−
6.0
V
I2C-bus inactive
1.0
−
6.0
V
fSCL = 100 kHz
−
−
200
µA
fSCL = 0 Hz; VDD = 5 V
−
10
50
µA
fSCL = 0 Hz; VDD = 1 V
−
2
10
µA
I2C-bus
active
Tamb
operating ambient temperature range
−40
−
+85
°C
Tstg
storage temperature range
−65
−
+150
°C
4
ORDERING INFORMATION
TYPE
NUMBER
PACKAGE
NAME
DESCRIPTION
VERSION
PCF8583P
DIP8
plastic dual in-line package; 8 leads (300 mil)
SOT97-1
PCF8583T
SO8
plastic small outline package; 8 leads; body width 7.5 mm
SOT176-1
1997 Jul 15
3
Philips Semiconductors
Product specification
Clock/calendar with 240 × 8-bit RAM
5
PCF8583
BLOCK DIAGRAM
handbook, full pagewidth
OSCI
OSCO
INT
VDD
VSS
A0
SCL
SDA
1
2
PCF8583
OSCILLATOR
32.768 kHz
DIVIDER
1 : 256
OR
100 : 128
POWER-ON
RESET
CONTROL
LOGIC
100 Hz
7
8
4
control/status
hundredth of a second
seconds
minutes
hours
year/date
weekdays/months
timer
alarm control
00
01
07
08
alarm registers
or RAM
3
I2C-BUS
INTERFACE
6
5
ADDRESS
REGISTER
0F
RAM
(240 × 8)
FF
MRB001
Fig.1 Block diagram.
6
PINNING
SYMBOL
OSCI
PIN
DESCRIPTION
1
oscillator input, 50 Hz or event-pulse
input
OSCO
2
oscillator output
A0
3
address input
VSS
4
negative supply
SDA
5
serial data line
SCL
6
serial clock line
INT
7
open drain interrupt output (active
LOW)
VDD
8
positive supply
1997 Jul 15
handbook, halfpage
OSCI
1
OSCO
2
A0
3
V SS
4
PCF8583P
PCF8583T
8
V DD
7
INT
6
SCL
5
SDA
MRB014
Fig.2 Pinning diagram.
4
Philips Semiconductors
Product specification
Clock/calendar with 240 × 8-bit RAM
7
PCF8583
Whenever an alarm event occurs the alarm flag of the
control/status register is set. A timer alarm event will set
the alarm flag and an overflow condition of the timer will set
the timer flag. The open drain interrupt output is switched
on (active LOW) when the alarm or timer flag is set
(enabled). The flags remain set until directly reset by a
write operation.
FUNCTIONAL DESCRIPTION
The PCF8583 contains a 256 by 8-bit RAM with an 8-bit
auto-increment address register, an on-chip 32.768 kHz
oscillator circuit, a frequency divider, a serial two-line
bidirectional I2C-bus interface and a power-on reset circuit.
The first 16 bytes of the RAM (memory addresses
00 to 0F) are designed as addressable 8-bit parallel
special function registers. The first register (memory
address 00) is used as a control/status register.
The memory addresses 01 to 07 are used as counters for
the clock function. The memory addresses 08 to 0F may
be programmed as alarm registers or used as free RAM
locations, when the alarm is disabled.
7.1
When the alarm is disabled (Bit 2 of control/status
register = 0) the alarm registers at addresses 08 to 0F
may be used as free RAM.
7.3
The control/status register is defined as the memory
location 00 with free access for reading and writing via the
I2C-bus. All functions and options are controlled by the
contents of the control/status register (see Fig.3).
Counter function modes
When the control/status register is programmed, a
32.768 kHz clock mode, a 50 Hz clock mode or an
event-counter mode can be selected.
7.4
The year and date are packed into memory location 05
(see Fig.6). The weekdays and months are packed into
memory location 06 (see Fig.7). When reading these
memory locations the year and weekdays are masked out
when the mask flag of the control/status register is set.
This allows the user to read the date and month count
directly.
When one of the counters is read (memory locations
01 to 07), the contents of all counters are strobed into
capture latches at the beginning of a read cycle. Therefore,
faulty reading of the count during a carry condition is
prevented.
In the event-counter mode events are stored in BCD
format. D5 is the most significant and D0 the least
significant digit. The divider is by-passed.
When a counter is written, other counters are not affected.
In the different modes the counter registers are
programmed and arranged as shown in Fig.4. Counter
cycles are listed in Table 1.
Alarm function modes
By setting the alarm enable bit of the control/status register
the alarm control register (address 08) is activated.
By setting the alarm control register a dated alarm, a daily
alarm, a weekday alarm or a timer alarm may be
programmed. In the clock modes, the timer register
(address 07) may be programmed to count hundredths of
a second, seconds, minutes, hours or days. Days are
counted when an alarm is not programmed.
1997 Jul 15
Counter registers
In the clock modes 24 h or 12 h format can be selected by
setting the most significant bit of the hours counter
register. The format of the hours counter is shown in Fig.5.
In the clock modes the hundredths of a second, seconds,
minutes, hours, date, month (four year calendar) and
weekday are stored in a BCD format. The timer register
stores up to 99 days. The event counter mode is used to
count pulses applied to the oscillator input (OSCO left
open-circuit). The event counter stores up to 6 digits of
data.
7.2
Control/status register
5
Philips Semiconductors
Product specification
Clock/calendar with 240 × 8-bit RAM
handbook, full pagewidth
PCF8583
MSB
7
LSB
6
5
4
3
2
1
0
memory location 00
reset state: 0000 0000
timer flag
(50% duty factor
seconds flag if alarm
enable bit is 0)
alarm flag (50% duty factor
minutes flag if alarm
enable bit is 0)
alarm enable bit:
0 alarm disabled: flags toggle
alarm control register disabled
(memory locations 08 to 0F
are free RAM space)
1 enable alarm control register
(memory location 08 is the
alarm control register)
mask flag:
0
read locations 05 to 06
unmasked
1
read date and month count
directly
function mode :
00 clock mode 32.768 kHz
01 clock mode 50 Hz
10 event-counter mode
11 test modes
hold last count flag :
0 count
1 store and hold last count in
capture latches
stop counting flag :
0 count pulses
1 stop counting, reset divider
MRB017
Fig.3 Control/status register.
1997 Jul 15
6
Philips Semiconductors
Product specification
Clock/calendar with 240 × 8-bit RAM
handbook, full pagewidth
PCF8583
control/status
control/status
hundredth of a second
1/10 s
1/100 s
seconds
10 s
1s
minutes
10 min
1 min
hours
10 h
1h
year/date
10 day
1 day
weekday/month
10 month
1 month
timer
10 day
1 day
00
D1
D0
D3
D2
02
D4
03
D5
01
free
04
free
05
free
06
timer
T1
T0
07
alarm control
alarm control
08
hundredth of a second
1/10 s
1/100 s
alarm seconds
alarm minutes
alarm
D1
alarm
D0
D3
D2
D5
D4
09
0A
0B
alarm hours
free
alarm date
0C
free
alarm month
free
alarm timer
alarm timer
free RAM
free RAM
CLOCK MODES
0D
0E
0F
EVENT COUNTER
MRB015
Fig.4 Register arrangement.
1997 Jul 15
7
Philips Semiconductors
Product specification
Clock/calendar with 240 × 8-bit RAM
handbook, full pagewidth
MSB
7
PCF8583
LSB
6
5
4
3
2
1
0
memory location 04 (hours counter)
reset state: 0000 0000
unit hours BCD
ten hours (0 to 2 binary)
AM/PM flag:
0 AM
1 PM
format:
0 24 h format, AM/PM flag
remains unchanged
1 12 h format, AM/PM flag
will be updated
MRB002
Fig.5 Format of the hours counter.
handbook, full pagewidth
MSB
7
LSB
6
5
4
3
2
1
0
memory location 05 (year/date)
reset state: 0000 0001
unit days BCD
ten days (0 to 3 binary)
year (0 to 3 binary, read as 0 if
the mask flag is set)
MRB003
Fig.6 Format of the year/date counter.
handbook, full pagewidth
MSB
7
LSB
6
5
4
3
2
1
0
memory location 06 (weekdays/months)
reset state: 0000 0001
unit months BCD
ten months
weekdays (0 to 6 binary, read as 0 if
the mask flag is set)
MRB004
Fig.7 Format of the weekdays/month counter.
1997 Jul 15
8
Philips Semiconductors
Product specification
Clock/calendar with 240 × 8-bit RAM
Table 1
PCF8583
Cycle length of the time counters, clock modes
UNIT
COUNTING CYCLE
CONTENTS OF THE
MONTH COUNTER
CARRY TO NEXT UNIT
Hundredths of a second
00 to 99
99 to 00
−
Seconds
00 to 59
59 to 00
−
Minutes
00 to 59
59 to 00
−
Hours (24 h)
00 to 23
23 to 00
−
Hours (12 h)
12 AM
−
−
01 AM to 11 AM
−
−
12 PM
−
−
01 PM to 11 PM
11 PM to 12 AM
−
01 to 31
31 to 01
1, 3, 5, 7, 8, 10 and 12
01 to 30
30 to 01
4, 6, 9 and 11
01 to 29
29 to 01
2, year = 0
01 to 28
28 to 01
2, year = 1, 2 and 3
Months
01 to 12
12 to 01
−
Year
0 to 3
−
−
Weekdays
0 to 6
6 to 0
−
Timer
00 to 99
no carry
−
Date
7.5
An alarm signal is generated when the contents of the
alarm registers matches bit-by-bit the contents of the
involved counter registers. The year and weekday bits are
ignored in a dated alarm. A daily alarm ignores the month
and date bits. When a weekday alarm is selected, the
contents of the alarm weekday/month register will select
the weekdays on which an alarm is activated (see Fig.9).
Alarm control register
When the alarm enable bit of the control/status register is
set (address 00, bit 2) the alarm control register (address
08) is activated. All alarm, timer, and interrupt output
functions are controlled by the contents of the alarm
control register (see Fig.8).
7.6
Remark: In the 12 h mode, bits 6 and 7 of the alarm hours
register must be the same as the hours counter.
Alarm registers
All alarm registers are allocated with a constant address
offset of hexadecimal 08 to the corresponding counter
registers (see Fig.4, Register arrangement).
1997 Jul 15
9
Philips Semiconductors
Product specification
Clock/calendar with 240 × 8-bit RAM
handbook, full pagewidth
PCF8583
MSB
7
LSB
6
5
4
3
2
1
0
memory location 08
reset state: 0000 0000
timer function :
000
001
010
011
100
101
110
111
no timer
hundredths of a second
seconds
minutes
hours
days
not used
test mode, all counters
in parallel (factory use only)
timer interrupt enable :
0
1
timer flag, no interrupt
timer flag, interrupt
clock alarm function :
00
01
10
11
no clock alarm
daily alarm
weekday alarm
dated alarm
timer alarm enable :
0
1
no timer alarm
timer alarm
alarm interrupt enable :
MRB005
(valid only when 'alarm enable' in
control / status register is set
0
1
alarm flag, no interrupt
alarm flag, interrupt
Fig.8 Alarm control register; clock mode.
1997 Jul 15
10
Philips Semiconductors
Product specification
Clock/calendar with 240 × 8-bit RAM
handbook, full pagewidth
MSB
7
PCF8583
LSB
6
5
4
3
2
1
0
memory location 0E (alarm weekday / month)
weekday 0 enabled when set
weekday 1 enabled when set
weekday 2 enabled when set
weekday 3 enabled when set
weekday 4 enabled when set
weekday 5 enabled when set
weekday 6 enabled when set
not used
MRB006
Fig.9 Selection of alarm weekdays.
7.7
The event counter stores up to 6 digits of data, which are
stored as 6 hexadecimal values located in locations 1, 2,
and 3. Thus, up to 1 million events may be recorded.
Timer
The timer (location 07) is enabled by setting the
control/status register = XX0X X1XX. The timer counts up
from 0 (or a programmed value) to 99. On overflow, the
timer resets to 0. The timer flag (LSB of control/status
register) is set on overflow of the timer. This flag must be
reset by software. The inverted value of this flag can be
transferred to the external interrupt by setting bit 3 of the
alarm control register.
An event counter alarm occurs when the event counter
registers match the value programmed in locations 9, A,
and B, and the event alarm is enabled (bits 4 and 5 which
are logic 0, 1 in the alarm control register). In this event,
the alarm flag (bit 1 of the control/status register) is set.
The inverted value of this flag can be transferred to the
interrupt pin (pin 7) by setting the alarm interrupt enable in
the alarm control register. In this mode, the timer
(location 07) increments once for every one, one-hundred,
ten thousand, or 1 million events, depending on the value
programmed in bits 0, 1 and 2 of the alarm control register.
In all other events, the timer functions are as in the clock
mode.
Additionally, a timer alarm can be programmed by setting
the timer alarm enable (bit 6 of the alarm control register).
When the value of the timer equals a pre-programmed
value in the alarm timer register (location 0F), the alarm
flag is set (bit 1 of the control/status register). The inverted
value of the alarm flag can be transferred to the external
interrupt by enabling the alarm interrupt (bit 6 of the alarm
control register).
7.9
Resolution of the timer is programmed via the 3 LSBs of
the alarm control register (see Fig.11, Alarm and timer
Interrupt logic diagram).
7.8
The conditions for activating the open-drain n-channel
interrupt output INT (active LOW) are determined by
appropriate programming of the alarm control register.
These conditions are clock alarm, timer alarm, timer
overflow, and event counter alarm. An interrupt occurs
when the alarm flag or the timer flag is set, and the
corresponding interrupt is enabled. In all events, the
interrupt is cleared only by software resetting of the flag
which initiated the interrupt.
Event counter mode
Event counter mode is selected by bits 4 and 5 which are
logic 1, 0 in the control/status register. The event counter
mode is used to count pulses externally applied to the
oscillator input (OSCO left open-circuit).
1997 Jul 15
Interrupt output
11
Philips Semiconductors
Product specification
Clock/calendar with 240 × 8-bit RAM
handbook, full pagewidth
PCF8583
MSB
7
LSB
6
5
4
3
2
1
0
memory location 08
reset state: 0000 0000
timer function :
000
001
010
011
100
101
110
111
no timer
units
100
10 000
1 000 000
not allowed
not allowed
test mode, all counters
in parallel
timer interrupt enable :
0
1
timer flag, no interrupt
timer flag, interrupt
clock alarm function :
00
01
10
11
no event alarm
event alarm
not allowed
not allowed
timer alarm enable :
0
1
no timer alarm
timer alarm
alarm interrupt enable :
MRB007
0
1
alarm flag, no interrupt
alarm flag, interrupt
Fig.10 Alarm control register, event-counter mode.
In the clock mode, if the alarm enable is not activated
(alarm enable bit of control/status register is logic 0), the
interrupt output toggles at 1 Hz with a 50% duty cycle (may
be used for calibration). This is the default power-on state
of the device. The OFF voltage of the interrupt output may
exceed the supply voltage, up to a maximum of 6.0 V.
A logic diagram of the interrupt output is shown in Fig.11.
7.10
This allows the user to feed the 50 Hz reference frequency
or an external high speed event signal into the input OSCI.
7.11
When power-up occurs the I2C-bus interface, the
control/status register and all clock counters are reset.
The device starts time-keeping in the 32.768 kHz clock
mode with the 24 h format on the first of January at
0.00.00: 00. A 1 Hz square wave with 50% duty cycle
appears at the interrupt output pin (starts HIGH).
Oscillator and divider
A 32.768 kHz quartz crystal has to be connected to OSCI
(pin 1) and OSCO (pin 2). A trimmer capacitor between
OSCI and VDD is used for tuning the oscillator (see quartz
frequency adjustment). A 100 Hz clock signal is derived
from the quartz oscillator for the clock counters.
It is recommended to set the stop counting flag of the
control/status register before loading the actual time into
the counters. Loading of illegal states may lead to a
temporary clock malfunction.
In the 50 Hz clock mode or event-counter mode the
oscillator is disabled and the oscillator input is switched to
a high impedance state.
1997 Jul 15
Initialization
12
Philips Semiconductors
Product specification
Clock/calendar with 240 × 8-bit RAM
PCF8583
handbook, full pagewidth
MUX
oscillator
mode
select
counter
CLOCK/CALENDAR
control
TIMER
ALARM
clock
alarm
7
6
alarm
control
5
4
3
2
1
timer
alarm
0
timer
control
overflow
7
6
5
4
CONTROL/STATUS
3
2
1
0
ALARM
CONTROL
REGISTER
REGISTER (1)
alarm
interrupt
timer overflow
interrupt
INT
MBD818
(1) If the alarm enable bit of the control/status register is reset (logic 0), a 1 Hz signal can be observed on the interrupt pin INT.
Fig.11 Alarm and timer interrupt logic diagram.
1997 Jul 15
13
Philips Semiconductors
Product specification
Clock/calendar with 240 × 8-bit RAM
8
PCF8583
CHARACTERISTICS OF THE I2C-BUS
The I2C-bus is for bidirectional, two-line communication between different ICs or modules. The two lines are a serial data
line (SDA) and a serial clock line (SCL). Both lines must be connected to a positive supply via a pull-up resistor. Data
transfer may be initiated only when the bus is not busy.
8.1
Bit transfer (see Fig.12)
One data bit is transferred during each clock pulse. The data on the SDA line must remain stable during the HIGH period
of the clock pulse as changes in the data line at this time will be interpreted as a control signal.
SDA
SCL
change
of data
allowed
data line
stable;
data valid
MBC621
Fig.12 Bit transfer.
8.2
Start and stop conditions (see Fig.13)
Both data and clock lines remain HIGH when the bus is not busy. A HIGH-to-LOW transition of the data line, while the
clock is HIGH is defined as the start condition (S). A LOW-to-HIGH transition of the data line while the clock is HIGH is
defined as the stop condition (P).
SDA
SDA
SCL
SCL
S
P
START condition
STOP condition
Fig.13 Definition of start and stop conditions.
1997 Jul 15
14
MBC622
Philips Semiconductors
Product specification
Clock/calendar with 240 × 8-bit RAM
8.3
PCF8583
System configuration (see Fig.14)
A device generating a message is a ‘transmitter’, a device receiving a message is the ‘receiver’. The device that controls
the message is the ‘master’ and the devices which are controlled by the master are the ‘slaves’.
SDA
SCL
MASTER
TRANSMITTER /
RECEIVER
SLAVE
TRANSMITTER /
RECEIVER
SLAVE
RECEIVER
MASTER
TRANSMITTER /
RECEIVER
MASTER
TRANSMITTER
MBA605
Fig.14 System configuration.
8.4
The device that acknowledges must pull down the SDA
line during the acknowledge clock pulse, so that the SDA
line is stable LOW during the HIGH period of the
acknowledge related clock pulse (set-up and hold times
must be taken into consideration). A master receiver must
signal an end of data to the transmitter by not generating
an acknowledge on the last byte that has been clocked out
of the slave. In this event the transmitter must leave the
data line HIGH to enable the master to generate a stop
condition.
Acknowledge (see Fig.15)
The number of data bytes transferred between the start
and stop conditions from transmitter to receiver is
unlimited. Each byte of eight bits is followed by an
acknowledge bit. The acknowledge bit is a HIGH level
signal put on the bus by the transmitter during which time
the master generates an extra acknowledge related clock
pulse. A slave receiver which is addressed must generate
an acknowledge after the reception of each byte. Also a
master receiver must generate an acknowledge after the
reception of each byte that has been clocked out of the
slave transmitter.
DATA OUTPUT
BY TRANSMITTER
not acknowledge
DATA OUTPUT
BY RECEIVER
acknowledge
SCL FROM
MASTER
1
2
8
9
S
START
CONDITION
MBC602
Fig.15 Acknowledgment on the I2C-bus.
1997 Jul 15
15
clock pulse for
acknowledgement
Philips Semiconductors
Product specification
Clock/calendar with 240 × 8-bit RAM
9
9.1
PCF8583
I2C-BUS PROTOCOL
Addressing
Before any data is transmitted on the I2C-bus, the device which should respond is addressed first. The addressing is
always carried out with the first byte transmitted after the start procedure.
The clock/calendar acts as a slave receiver or slave transmitter. Therefore the clock signal SCL is only an input signal,
but the data signal SDA is a bidirectional line.
The clock/calendar slave address is shown in Fig.16. Bit A0 corresponds to hardware address pin A0. Connecting this
pin to VDD or VSS allows the device to have one of two different addresses.
handbook, halfpage
1
0
1
0
0
0
A0 R/W
MRB016
group 2
group 1
Fig.16 Slave address.
9.2
Clock/calendar READ/WRITE cycles
The I2C-bus configuration for the different PCF8583 READ and WRITE cycles is shown in Figs 17, 18 and 19.
acknowledgement
from slave
acknowledgement
from slave
handbook, full pagewidth
S
SLAVE ADDRESS
0 A
WORD ADDRESS
R/W
A
acknowledgement
from slave
DATA
A
P
n bytes
auto increment
memory word address
MBD822
Fig.17 Master transmits to slave receiver (WRITE) mode.
1997 Jul 15
16
Philips Semiconductors
Product specification
Clock/calendar with 240 × 8-bit RAM
handbook, full pagewidth
S
acknowledgement
from slave
acknowledgement
from slave
SLAVE ADDRESS
0 A
PCF8583
WORD ADDRESS
R/W
A
S
acknowledgement
from slave
SLAVE ADDRESS
at this moment master transmitter becomes
master - receiver and
PCF8593 slave - receiver
becomes slave - transmitter
1 A
R/W
acknowledgement
from master
DATA
A
n bytes
auto increment
memory word address
no acknowledgement
from master
DATA
1
P
last byte
auto increment
memory word address
MBD823
Fig.18 Master reads after setting word address (write word address; READ data).
acknowledgement
from slave
acknowledgement
from slave
handbook, full pagewidth
S
SLAVE ADDRESS
1 A
R/W
DATA
A
n bytes
acknowledgement
from slave
DATA
1
P
last bytes
auto increment
word address
auto increment
word address
MBD824
Fig.19 Master reads slave immediately after first byte (READ mode).
1997 Jul 15
17
Philips Semiconductors
Product specification
Clock/calendar with 240 × 8-bit RAM
PCF8583
10 LIMITING VALUES
In accordance with the Absolute Maximum Rating System (IEC 134).
SYMBOL
PARAMETER
MIN.
MAX.
UNIT
VDD
supply voltage (pin 8)
−0.8
+7.0
V
IDD
supply current (pin 8)
−
50
mA
ISS
supply current (pin 4)
−
50
mA
VI
input voltage
−0.8
VDD + 0.8
V
II
DC input current
−
10
mA
IO
DC output current
−
10
mA
Ptot
total power dissipation per package
−
300
mW
PO
power dissipation per output
−
50
mW
Tamb
operating ambient temperature
−40
+85
°C
Tstg
storage temperature
−65
+150
°C
11 HANDLING
Inputs and outputs are protected against electrostatic charge in normal handling. However, to be totally safe, it is
desirable to take normal precautions appropriate to handling MOS devices. Advice can be found in Data Handbook IC12
under “Handling MOS Devices”.
12 DC CHARACTERISTICS
VDD = 2.5 to 6.0 V; VSS = 0 V; Tamb = −40 to +85 °C unless otherwise specified.
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.(1)
MAX.
UNIT
supply voltage
(operating mode)
I2C-bus
2.5
−
6.0
V
I2C-bus inactive
1.0
−
6.0
V
VDDosc
supply voltage
(quartz oscillator)
Tamb = 0 to 70 °C; note 2
1.0
−
6.0
V
IDD
supply current
(operating mode)
fSCL = 100 kHz; clock mode;
note 3
−
−
200
µA
IDDO
supply current
(clock mode)
see Fig.20
fSCL = 0 Hz; VDD = 5 V
−
10
50
µA
fSCL = 0 Hz; VDD = 1 V
−
2
10
µA
data retention
fOSCI = 0 Hz; VDD = 1 V
Tamb = −40 to + 85 °C
−
−
5
µA
Tamb = −25 to + 70 °C
−
−
2
µA
note 4
1.5
1.9
2.3
V
V
VDD
IDDR
VEN
I2C-bus
enable level
active
SDA
VIL
LOW level input voltage
note 5
−0.8
−
0.3VDD
VIH
HIGH level input voltage
note 5
0.7VDD
−
VDD +0.8 V
IOL
LOW level output current
VOL = 0.4 V
3
−
−
mA
ILI
input leakage current
VI = VDD or VSS
−1
−
+1
µA
Ci
input capacitance
note 6
−
−
7
pF
1997 Jul 15
18
Philips Semiconductors
Product specification
Clock/calendar with 240 × 8-bit RAM
SYMBOL
PARAMETER
PCF8583
CONDITIONS
MIN.
TYP.(1)
MAX.
UNIT
A0; OSCI
input leakage current
Vl = VDD or VSS
−250
−
+250
nA
IOL
LOW level output current
VOL = 0.4 V
3
−
−
mA
ILI
input leakage current
Vl = VDD or VSS
−1
−
+1
µA
Ci
input capacitance
note 6
−
−
7
pF
ILI
input leakage current
VI = VDD or VSS
−1
−
+1
µA
ILI
INT
SCL
Notes
1. Typical values measured at Tamb = 25 °C.
2. When powering-up the device, VDD must exceed 1.5 V until stable operation of the oscillator is established.
3. Event counter mode: supply current dependant upon input frequency.
4. The I2C-bus logic is disabled if VDD < VEN.
5. When the voltages are above or below the supply voltages VDD or VSS, an input current may flow; this current
must not exceed ±0.5 mA.
6. Tested on sample basis.
MRB012
12
handbook, halfpage
I DDO
(µA)
8
4
0
0
2
4
V DD (V)
6
fSCL = 32 kHz; Tamb = 25 °C.
Fig.20 Typical supply current in clock mode as a function of supply voltage.
1997 Jul 15
19
Philips Semiconductors
Product specification
Clock/calendar with 240 × 8-bit RAM
PCF8583
13 AC CHARACTERISTICS
VDD = 2.5 to 6.0 V; VSS = 0 V; Tamb = −40 to +85 °C; unless otherwise specified.
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
Oscillator
Cosc
integrated oscillator
capacitance
∆fosc
oscillator stability
fi
input frequency
−
40
−
for ∆VDD = 100 mV;
Tamb = 25 °C; VDD = 1.5 V
−
2 × 10−7
−
note 1
−
−
1
MHz
pF
Quartz crystal parameters (f = 32.768 kHz)
Rs
series resistance
−
−
40
kΩ
CL
parallel load capacitance
−
10
−
pF
CT
trimmer capacitance
5
−
25
pF
−
100
kHz
I2C-bus
timing (see Fig.21; notes 2 and 3)
fSCL
SCL clock frequency
−
tSP
tolerable spike width on bus
−
−
100
ns
tBUF
bus free time
4.7
−
−
µs
tSU;STA
START condition set-up time
4.7
−
−
µs
tHD;STA
START condition hold time
4.0
−
−
µs
tLOW
SCL LOW time
4.7
−
−
µs
tHIGH
SCL HIGH time
4.0
−
−
µs
tr
SCL and SDA rise time
−
−
1.0
µs
tf
SCL and SDA fall time
−
−
0.3
µs
tSU;DAT
data set-up time
250
−
−
ns
tHD;DAT
data hold time
0
−
−
ns
tVD;DAT
SCL LOW to data out valid
−
−
3.4
µs
tSU;STO
STOP condition set-up time
4.0
−
−
µs
Notes
1. Event counter mode only.
2. All timing values are valid within the operating supply voltage and ambient temperature range and reference to VIL
and VIH with an input voltage swing of VSS to VDD.
3. A detailed description of the I2C-bus specification, with applications, is given in brochure “The I2C-bus and how to
use it”. This brochure may be ordered using the code 9398 393 40011.
1997 Jul 15
20
Philips Semiconductors
Product specification
Clock/calendar with 240 × 8-bit RAM
handbook, full pagewidth
t
t
SU;STA
BIT 6
(A6)
BIT 7
MSB
(A7)
START
CONDITION
(S)
PROTOCOL
LOW
PCF8583
t HIGH
BIT 0
LSB
(R/W)
ACKNOWLEDGE
(A)
STOP
CONDITION
(P)
1 / f SCL
SCL
t
tr
BUF
tf
SDA
t HD;STA
t SU;DAT
t
t VD;DAT
HD;DAT
MBD820
t SU;STO
Fig.21 I2C-bus timing diagram; rise and fall times refer to VIL and VIH.
14 APPLICATION INFORMATION
Procedure:
14.1
• Power-on
14.1.1
Quartz frequency adjustment
• Initialization (alarm functions).
METHOD 1: FIXED OSCI CAPACITOR
Routine:
By evaluating the average capacitance necessary for the
application layout a fixed capacitor can be used.
The frequency is best measured via the 1 Hz signal
available after power-on at the interrupt output (pin 7).
The frequency tolerance depends on the quartz crystal
tolerance, the capacitor tolerance and the
device-to-device tolerance (on average ±5 × 10−6).
Average deviations of ±5 minutes per year can be
achieved.
14.1.2
• Set clock to time T and set alarm to time T + dT
• At time T + dT (interrupt) repeat routine.
14.1.3
Direct measurement of OSC out (accounting for test probe
capacitance).
The PCF8583 slave address has a fixed combination 1010
as group 1.
METHOD 2: OSCI TRIMMER
Using the alarm function (via the I2C-bus) a signal faster
than 1 Hz can be generated at the interrupt output for fast
setting of a trimmer.
1997 Jul 15
METHOD 3:
21
Philips Semiconductors
Product specification
Clock/calendar with 240 × 8-bit RAM
PCF8583
V DD
handbook, full pagewidth
SDA
V DD
SCL
MASTER
TRANSMITTER
A0
CLOCK
CALENDAR
OSCI PCF8583
'1010'
OSCO
SCL
SDA
V SS
VDD
VDD
1
A0
OSCI
EVENT
COUNTER
PCF8583
'1010'
OSCO
SCL
SDA
V SS
V DD
R
SDA
Fig.22 Application diagram.
22
R: pull-up resistor
R = trise / C-bus
SCL
(I 2C-bus)
1997 Jul 15
R
MRB018
Philips Semiconductors
Product specification
Clock/calendar with 240 × 8-bit RAM
PCF8583
15 PACKAGE OUTLINES
DIP8: plastic dual in-line package; 8 leads (300 mil)
SOT97-1
ME
seating plane
D
A2
A
A1
L
c
Z
w M
b1
e
(e 1)
b
MH
b2
5
8
pin 1 index
E
1
4
0
5
10 mm
scale
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
UNIT
A
max.
A1
min.
A2
max.
b
b1
b2
c
D (1)
E (1)
e
e1
L
ME
MH
w
Z (1)
max.
mm
4.2
0.51
3.2
1.73
1.14
0.53
0.38
1.07
0.89
0.36
0.23
9.8
9.2
6.48
6.20
2.54
7.62
3.60
3.05
8.25
7.80
10.0
8.3
0.254
1.15
inches
0.17
0.020
0.13
0.068
0.045
0.021
0.015
0.042
0.035
0.014
0.009
0.39
0.36
0.26
0.24
0.10
0.30
0.14
0.12
0.32
0.31
0.39
0.33
0.01
0.045
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
REFERENCES
OUTLINE
VERSION
IEC
JEDEC
SOT97-1
050G01
MO-001AN
1997 Jul 15
EIAJ
EUROPEAN
PROJECTION
ISSUE DATE
92-11-17
95-02-04
23
Philips Semiconductors
Product specification
Clock/calendar with 240 × 8-bit RAM
PCF8583
SO8: plastic small outline package; 8 leads; body width 7.5 mm
SOT176-1
D
E
A
X
c
y
HE
v M A
Z
8
5
Q
A2
A
(A 3)
A1
pin 1 index
θ
Lp
L
1
4
e
detail X
w M
bp
0
5
10 mm
scale
DIMENSIONS (inch dimensions are derived from the original mm dimensions)
UNIT
A
max.
A1
A2
A3
bp
c
D (1)
E (1)
e
HE
L
Lp
Q
v
w
y
Z (1)
mm
2.65
0.3
0.1
2.45
2.25
0.25
0.49
0.36
0.32
0.23
7.65
7.45
7.6
7.4
1.27
10.65
10.00
1.45
1.1
0.45
1.1
1.0
0.25
0.25
0.1
2.0
1.8
0.012 0.096
0.004 0.089
0.01
0.019 0.013
0.014 0.009
0.30
0.29
0.30
0.29
0.050
0.419
0.057
0.394
0.043
0.018
0.043
0.039
0.01
0.01
0.004
0.079
0.071
inches
0.10
θ
Note
1. Plastic or metal protrusions of 0.15 mm maximum per side are not included.
OUTLINE
VERSION
REFERENCES
IEC
JEDEC
EIAJ
ISSUE DATE
95-02-25
97-05-22
SOT176-1
1997 Jul 15
EUROPEAN
PROJECTION
24
o
8
0o
Philips Semiconductors
Product specification
Clock/calendar with 240 × 8-bit RAM
PCF8583
Several techniques exist for reflowing; for example,
thermal conduction by heated belt. Dwell times vary
between 50 and 300 seconds depending on heating
method. Typical reflow temperatures range from
215 to 250 °C.
16 SOLDERING
16.1
Introduction
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
Preheating is necessary to dry the paste and evaporate
the binding agent. Preheating duration: 45 minutes at
45 °C.
16.3.2
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “IC Package Databook” (order code 9398 652 90011).
16.2
16.2.1
Wave soldering techniques can be used for all SO
packages if the following conditions are observed:
• A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave) soldering
technique should be used.
DIP
SOLDERING BY DIPPING OR BY WAVE
• The longitudinal axis of the package footprint must be
parallel to the solder flow.
The maximum permissible temperature of the solder is
260 °C; solder at this temperature must not be in contact
with the joint for more than 5 seconds. The total contact
time of successive solder waves must not exceed
5 seconds.
• The package footprint must incorporate solder thieves at
the downstream end.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
The device may be mounted up to the seating plane, but
the temperature of the plastic body must not exceed the
specified maximum storage temperature (Tstg max). If the
printed-circuit board has been pre-heated, forced cooling
may be necessary immediately after soldering to keep the
temperature within the permissible limit.
16.2.2
Maximum permissible solder temperature is 260 °C, and
maximum duration of package immersion in solder is
10 seconds, if cooled to less than 150 °C within
6 seconds. Typical dwell time is 4 seconds at 250 °C.
REPAIRING SOLDERED JOINTS
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
Apply a low voltage soldering iron (less than 24 V) to the
lead(s) of the package, below the seating plane or not
more than 2 mm above it. If the temperature of the
soldering iron bit is less than 300 °C it may remain in
contact for up to 10 seconds. If the bit temperature is
between 300 and 400 °C, contact may be up to 5 seconds.
16.3
16.3.1
16.3.3
REPAIRING SOLDERED JOINTS
Fix the component by first soldering two diagonallyopposite end leads. Use only a low voltage soldering iron
(less than 24 V) applied to the flat part of the lead. Contact
time must be limited to 10 seconds at up to 300 °C. When
using a dedicated tool, all other leads can be soldered in
one operation within 2 to 5 seconds between
270 and 320 °C.
SO
REFLOW SOLDERING
Reflow soldering techniques are suitable for all SO
packages.
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
1997 Jul 15
WAVE SOLDERING
25
Philips Semiconductors
Product specification
Clock/calendar with 240 × 8-bit RAM
PCF8583
17 DEFINITIONS
Data sheet status
Objective specification
This data sheet contains target or goal specifications for product development.
Preliminary specification
This data sheet contains preliminary data; supplementary data may be published later.
Product specification
This data sheet contains final product specifications.
Limiting values
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or
more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation
of the device at these or at any other conditions above those given in the Characteristics sections of the specification
is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.
18 LIFE SUPPORT APPLICATIONS
These products are not designed for use in life support appliances, devices, or systems where malfunction of these
products can reasonably be expected to result in personal injury. Philips customers using or selling these products for
use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such
improper use or sale.
19 PURCHASE OF PHILIPS I2C COMPONENTS
Purchase of Philips I2C components conveys a license under the Philips’ I2C patent to use the
components in the I2C system provided the system conforms to the I2C specification defined by
Philips. This specification can be ordered using the code 9398 393 40011.
1997 Jul 15
26
Philips Semiconductors
Product specification
Clock/calendar with 240 × 8-bit RAM
PCF8583
NOTES
1997 Jul 15
27
Philips Semiconductors – a worldwide company
Argentina: see South America
Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113,
Tel. +61 2 9805 4455, Fax. +61 2 9805 4466
Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213, Tel. +43 160 1010,
Fax. +43 160 101 1210
Belarus: Hotel Minsk Business Center, Bld. 3, r. 1211, Volodarski Str. 6,
220050 MINSK, Tel. +375 172 200 733, Fax. +375 172 200 773
Belgium: see The Netherlands
Brazil: see South America
Bulgaria: Philips Bulgaria Ltd., Energoproject, 15th floor,
51 James Bourchier Blvd., 1407 SOFIA,
Tel. +359 2 689 211, Fax. +359 2 689 102
Canada: PHILIPS SEMICONDUCTORS/COMPONENTS,
Tel. +1 800 234 7381
China/Hong Kong: 501 Hong Kong Industrial Technology Centre,
72 Tat Chee Avenue, Kowloon Tong, HONG KONG,
Tel. +852 2319 7888, Fax. +852 2319 7700
Colombia: see South America
Czech Republic: see Austria
Denmark: Prags Boulevard 80, PB 1919, DK-2300 COPENHAGEN S,
Tel. +45 32 88 2636, Fax. +45 31 57 0044
Finland: Sinikalliontie 3, FIN-02630 ESPOO,
Tel. +358 9 615800, Fax. +358 9 61580920
France: 4 Rue du Port-aux-Vins, BP317, 92156 SURESNES Cedex,
Tel. +33 1 40 99 6161, Fax. +33 1 40 99 6427
Germany: Hammerbrookstraße 69, D-20097 HAMBURG,
Tel. +49 40 23 53 60, Fax. +49 40 23 536 300
Greece: No. 15, 25th March Street, GR 17778 TAVROS/ATHENS,
Tel. +30 1 4894 339/239, Fax. +30 1 4814 240
Hungary: see Austria
India: Philips INDIA Ltd, Band Box Building, 2nd floor,
254-D, Dr. Annie Besant Road, Worli, MUMBAI 400 025,
Tel. +91 22 493 8541, Fax. +91 22 493 0966
Indonesia: see Singapore
Ireland: Newstead, Clonskeagh, DUBLIN 14,
Tel. +353 1 7640 000, Fax. +353 1 7640 200
Israel: RAPAC Electronics, 7 Kehilat Saloniki St, PO Box 18053,
TEL AVIV 61180, Tel. +972 3 645 0444, Fax. +972 3 649 1007
Italy: PHILIPS SEMICONDUCTORS, Piazza IV Novembre 3,
20124 MILANO, Tel. +39 2 6752 2531, Fax. +39 2 6752 2557
Japan: Philips Bldg 13-37, Kohnan 2-chome, Minato-ku, TOKYO 108,
Tel. +81 3 3740 5130, Fax. +81 3 3740 5077
Korea: Philips House, 260-199 Itaewon-dong, Yongsan-ku, SEOUL,
Tel. +82 2 709 1412, Fax. +82 2 709 1415
Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA, SELANGOR,
Tel. +60 3 750 5214, Fax. +60 3 757 4880
Mexico: 5900 Gateway East, Suite 200, EL PASO, TEXAS 79905,
Tel. +9-5 800 234 7381
Middle East: see Italy
Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB,
Tel. +31 40 27 82785, Fax. +31 40 27 88399
New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND,
Tel. +64 9 849 4160, Fax. +64 9 849 7811
Norway: Box 1, Manglerud 0612, OSLO,
Tel. +47 22 74 8000, Fax. +47 22 74 8341
Philippines: Philips Semiconductors Philippines Inc.,
106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI,
Metro MANILA, Tel. +63 2 816 6380, Fax. +63 2 817 3474
Poland: Ul. Lukiska 10, PL 04-123 WARSZAWA,
Tel. +48 22 612 2831, Fax. +48 22 612 2327
Portugal: see Spain
Romania: see Italy
Russia: Philips Russia, Ul. Usatcheva 35A, 119048 MOSCOW,
Tel. +7 095 755 6918, Fax. +7 095 755 6919
Singapore: Lorong 1, Toa Payoh, SINGAPORE 1231,
Tel. +65 350 2538, Fax. +65 251 6500
Slovakia: see Austria
Slovenia: see Italy
South Africa: S.A. PHILIPS Pty Ltd., 195-215 Main Road Martindale,
2092 JOHANNESBURG, P.O. Box 7430 Johannesburg 2000,
Tel. +27 11 470 5911, Fax. +27 11 470 5494
South America: Rua do Rocio 220, 5th floor, Suite 51,
04552-903 São Paulo, SÃO PAULO - SP, Brazil,
Tel. +55 11 821 2333, Fax. +55 11 829 1849
Spain: Balmes 22, 08007 BARCELONA,
Tel. +34 3 301 6312, Fax. +34 3 301 4107
Sweden: Kottbygatan 7, Akalla, S-16485 STOCKHOLM,
Tel. +46 8 632 2000, Fax. +46 8 632 2745
Switzerland: Allmendstrasse 140, CH-8027 ZÜRICH,
Tel. +41 1 488 2686, Fax. +41 1 481 7730
Taiwan: Philips Semiconductors, 6F, No. 96, Chien Kuo N. Rd., Sec. 1,
TAIPEI, Taiwan Tel. +886 2 2134 2865, Fax. +886 2 2134 2874
Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd.,
209/2 Sanpavuth-Bangna Road Prakanong, BANGKOK 10260,
Tel. +66 2 745 4090, Fax. +66 2 398 0793
Turkey: Talatpasa Cad. No. 5, 80640 GÜLTEPE/ISTANBUL,
Tel. +90 212 279 2770, Fax. +90 212 282 6707
Ukraine: PHILIPS UKRAINE, 4 Patrice Lumumba str., Building B, Floor 7,
252042 KIEV, Tel. +380 44 264 2776, Fax. +380 44 268 0461
United Kingdom: Philips Semiconductors Ltd., 276 Bath Road, Hayes,
MIDDLESEX UB3 5BX, Tel. +44 181 730 5000, Fax. +44 181 754 8421
United States: 811 East Arques Avenue, SUNNYVALE, CA 94088-3409,
Tel. +1 800 234 7381
Uruguay: see South America
Vietnam: see Singapore
Yugoslavia: PHILIPS, Trg N. Pasica 5/v, 11000 BEOGRAD,
Tel. +381 11 625 344, Fax.+381 11 635 777
For all other countries apply to: Philips Semiconductors, Marketing & Sales Communications,
Building BE-p, P.O. Box 218, 5600 MD EINDHOVEN, The Netherlands, Fax. +31 40 27 24825
Internet: http://www.semiconductors.philips.com
© Philips Electronics N.V. 1997
SCA55
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.
The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed
without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license
under patent- or other industrial or intellectual property rights.
Printed in The Netherlands
417067/00/05/pp28
Date of release: 1997 Jul 15
Document order number:
9397 750 02588