RH1056A - SPEC NO. 05-08-5019

SPEC NO. 05-08-5019 REV. T
RH1056A, PRECISION, HIGH SPEED, JFET INPUT OPERATIONAL AMPLIFIER
REVISION RECORD
DESCRIPTION
REV
DATE
0
INITIAL RELEASE
06/12/96
A
PAGE 18, TABLE II, DELETED VOS PARAMETER AND CHANGED +IB AND –IB DELTA LIMITS.
04/15/97
B
RELAXATION OF MAX VOS AT 25°C, FROM 180 μV to 300 μV, TABLE 1, PAGE 16; RELAXATION
07/31/97
OF MAX VOS AT MIL TEMPERATURES, FROM 500 μV to 700 μV , TABLE IA, PAGE 17. LTC P/N’S
CORRECTED, PAGE 2.
•
PAGE 2, ADDED PARAGRAPHS 3.2.1, 3.2.2, 3.2.3. ADDED “(SEE PARAGRAPH 3.2) TO
PARAGRAPH 3.3.b.
•
PAGE 3, ADDED PARAGRAPHS 3.8.1, 3.8.2, 3.8.3.
•
PAGE 4, PARAGRAPH 4.4.2, GROUP B INSPECTION WAS REDEFINED.
•
PAGE 5, PARAGRAPH 4.4.3, GROUP D INSPECTION WAS REDEFINED.
D
•
PAGE 4, AMENDED PARAGRAPH 4.1 AND 4.1.1 TAKING EXCEPTION TO ANALYSIS OF
CATASTROPHIC FAILURES.
04/08/98
E
•
CHANGED PACKAGE ON OPTION 3 FROM RH1056AMWB BOTTOM BRAZED FLATPACK TO
RH1056AMW GLASS SEALED FLATPACK.
05/15/98
F
•
PAGE 7,8,9, FIGURE 1,2,3 CHANGED 0JA AND 0JC.
09/28/99
G
•
•
PAGE 3, PARAGRAPHS 3.2.1, 3.2.2, 3.2.3 HAD FIGURES 1, 2, AND 3 REMOVED.
PAGE 4, PARAGRAPH 3.7, CHANGED VERBIAGE FROM “SPECIFIED IN TABLE III” TO “AND
AS SPECIFIED IN TABLE III HEREIN”, LINE 2.
PARAGRAPH 3.9, ADDED “HEREIN” AFTER “TABLE II”, LINE 2.
PAGE 5, PARAGRAPH 4.3, ADDED “HEREIN” AFTER “TABLE III”, LINE 2.
PARAGRAPH 4.4.1, ADDED “HEREIN” AFTER “TABLE III”, LINE 2.
PARAGRAPH 4.4.2.2, CHANGED VERBIAGE IN LINE 1 FROM “ALL FOOTNOTES OF TABLE
11A OF MIL-STD-883” TO “ALL FOOTNOTES PERTAINING TO TABLE IIA IN MIL-STD-885”.
PAGE 6, PARAGRAPH 4.4.3.2, CHANGED VERBIAGE IN LINE 1 FROM “ALL FOOTNOTES OF
TABLE IV OF MIL-STD-883” TO “ALL FOOTNOTES PERTAINING TO TABLE IV IN MIL-STD883’.
11/17/99
C
•
•
12/01/97
REVISION RECORD AND DESCRIPTION CONTINUED ON NEXT PAGE.
CAUTION: ELECTROSTATIC DISCHARGE SENSITIVE PART
REVISION
INDEX
REVISION
INDEX
PAGE NO.
REVISION
PAGE NO.
REVISION
APPLICATION
1
T
ORIG
DSGN
ENGR
MFG
CM
QA
PROG
FUNCT
2
T
3
T
4
T
5
T
6
T
7
T
8
T
9
T
10
T
11
T
12
T
13
T
14
T
15
T
LINEAR TECHNOLOGY CORPORATION
MILPITAS, CALIFORNIA
TITLE:
MICROCIRCUIT, LINEAR,
RH1056A, PRECISION, HIGH SPEED, JFET
INPUT OPERATIONAL AMPLIFIER
SIZE
SIGNOFFS
DATE
CAGE CODE
DRAWING NUMBER
REV
64155
05-08-5019
S
CONTRACT:
FOR OFFICIAL USE ONLY
LINEAR TECHNOLOGY CORPORATION
Page 1 of 15
SPEC NO. 05-08-5019 REV. T
REV
H
J
RH1056A, PRECISION, HIGH SPEED, JFET INPUT OPERATIONAL AMPLIFIER
REVISION RECORD
DESCRIPTION
• PAGE 9, CHANGED THETA JA TO 0JA=170°C/W AND THETA JC TO 0JC=40°C/W FROM
0JA=225°C/W AND 0JC=18°C/W PER PACKAGE ENGINEER.
• PAGE 3:
PARAGRAPH 3.2.1 ADDED “OPTION 1”, PARAGRAPH 3.2.2, ADDED “OPTION 2”, PARAGRAPH
3.2.3, ADDED “OPTION 3”.
DATE
09/05/00
01/15/03
• PAGE 4:
PARAGRAPH 3.6, TABLE IA CHANGED TO TABLE II.
PARAGRAPH 3.7, TABLE III CHANGED TO TABLE IV.
PARAGRAPH 3.9, TABLE II CHANGED TO TABLE III.
PARAGRAPH 3.10.3, ADDED “DEVICE OPTIONS 1, 2, AND 3” TO LINE 1.
PARAGRAPH 3.11.1 WAS CHANGED FROM “…dosage rate of approximately 20 Rads per
second” TO “…dosage rate of less than or equal to 10 Rads per second”.
• PAGE 5:
PARAGRAPHS 4.1 THROUGH 4.4.2.1 CHANGES WERE DONE TO CLARIFY GROUP SAMPLING.
• PAGE 6:
PARAGRAPH 4.4.3 CHANGE WAS DONE TO CLARIFY GROUP SAMPLING.
PARAGRAPHS 4.6.2 THROUGH 4.6.4 WERE RE-WRITTEN. THESE DATA PROVIDED, AND DATA
AVAILABLE.
PARAGRAPH 4.6.10 NOTE, ADDED FURTHER EXPLANATION OF MINIMUM DELIVERED DATA.
•
PAGES 7 THROUGH 16, ALL FIGURE TITLES CHANGED TO HAVE DEVICE OPTIONS AND
PACKAGE TYPES AT TOP OF PAGE, AND HAVE ALL FIGURES AT BOTTOM OF PAGE.
•
PAGE 8:
CASE OUTLINE REVISED. LEAD DIMENSION CHANGED FROM .068 TO 0.065.
•
PAGE 9:
CASE OUTLINE UPDATED TO MEET THE GUIDELINES OF MIL-STD-1835B.
•
PAGE 10, MOVED FIGURES 4, 5 AND 6 TO BETTER FIT THE PAGE.
•
PAGE 17, MOVED TABLES I AND II TO SAME PAGE. DATA SHEET REVISED: PRE-IRRAD
TABLE I, VOS HAD A SUBGROUP CHANGE FROM SUBGROUP 1 TO SUBGROUP 4. NOTES
WERE MADE NUMBERS INSTEAD OF ALPHAS FOR BOTH TABLE I AND TABLE II.
•
THIS SPECIFICATION IS NOW 18 PAGES INSTEAD OF 19 PAGES.
K
L
M
•
•
•
03/16/05
09/19/06
10/04/07
N
•
•
PAGE 4, CHANGED INITIAL RATE OF RADS TO 240 RADS/SEC.
PAGE 17, CHANGED SLEW RATE IN TABLE I AND TABLE II PER REVISED DATA SHEET.
PAGE 5, CHANGED IN BOTH PARAGRAPHS 4.2, 4.3 IN CONJUNCTION TO 3.3 CHANGED TO
3.4 AND PARAGRAPH 4.3 CHANGED 3.1.1 TO 3.1 AND 3.2.1 TO 3.1.1
PAGE 4, PARAGRAPH 3.10.3 ADDED OPTION 3 IS ALLOY 42 FOR FLATPACK.
PAGE 4, PARAGRAPH 3.10 3 CHANGED OPTION 2 TO ALLOY 42 PACKAGE REQUIREMENT.
PARAGRAPH 3.11.1 CHANGED VERBIAGE.
PAGE 5, PARAGRAPH 4.4.2 CHANGED VERBIAGE.
PAGE 8, FIGURE 2 NOTE 2 ADDED TO LEAD THICKNESS. REMOVED THROUGH OUT SPEC
RH1056AMJ8 OBSOLETE OPTION.
PAGE 14, 15: CHANGED DATASHEET TABLE I VOS, & NOTES, AND TABLE 2;
PAGE 15: TABLE IV, WIDENED VOS LIMITS FOR B5, B6, D3, AND D4 (PER PRODUCT
ENGINEER)
PAGE 15, TABLE III, DELTA LIMIT REQUIREMENTS: CORRECTED +IB AND –IB DELTA
MIN’S FROM -5.0 pA TO -50 pA AND DELTA MAX’S FROM 5.0 pA TO 50 pA.
PAGE 8, ADDED θja = +170°C/W and θjc = +40°C/W TO THE W10 CASE OUTLINE FOR
THERMAL RESISTANCE.
01/31/11
P
•
•
R
•
S
•
T
•
LINEAR TECHNOLOGY CORPORATION
05/01/08
06/27/08
04/02/09
5/10/10
Page 2 of 15
SPEC NO. 05-08-5019 REV. T
1.0
SCOPE:
1.1
2.0
RH1056A, PRECISION, HIGH SPEED, JFET INPUT OPERATIONAL AMPLIFIER
This specification defines the performance and test requirements for a microcircuit processed to a space
level manufacturing flow.
APPLICABLE DOCUMENTS:
2.1
Government Specifications and Standards: the following documents listed in the Department of Defense
Index of Specifications and Standards, of the issue in effect on the date of solicitation, form a part of this
specification to the extent specified herein.
SPECIFICATIONS:
2.2
3.0
MIL-PRF-38535
Integrated Circuits (Microcircuits) Manufacturing, General Specification for
MIL-STD-883
Test Method and Procedures for Microcircuits
MIL-STD-1835
Microcircuits Case Outlines
Order of Precedence: In the event of a conflict between the documents referenced herein and the contents
of this specification, the order of precedence shall be this specification, MIL-PRF-38535 and other
referenced specifications.
REQUIREMENTS:
3.1
General Description: This specification details the requirements for the RH1056A, PRECISION, HIGH
SPEED, JFET INPUT OPERATIONAL AMPLIFIER, processed to space level manufacturing flow.
3.2
Part Number:
3.3
3.2.1
Option 1 – RH1056AMH (TO5 Metal Can, 8 Leads)
3.2.2
Option 2 – RH1056AMW (Glass Sealed Flatpack, 10 Leads)
Part Marking Includes:
a.
LTC Logo
b.
LTC Part Number (See Paragraph 3.2)
c.
Date Code
d.
Serial Number
e.
ESD Identifier per MIL-PRF-38535, Appendix A
LINEAR TECHNOLOGY CORPORATION
Page 3 of 15
SPEC NO. 05-08-5019 REV. T
3.4
RH1056A, PRECISION, HIGH SPEED, JFET INPUT OPERATIONAL AMPLIFIER
The Absolute Maximum Ratings:
Supply Voltage
.
.
.
.
Differential Input Voltage
.
.
.
.
.
.
.
Input Voltage
.
Output Short Circuit Duration
Operating Temperature Range
Storage Temperature Range
Lead Temperature (Soldering, 10 sec)
. . . . . . . . . . . . . +20V
. . . . . . . . . . . . . +40V
. . . . . . . . . . . . . +20V
. . . . . . . . . . . INDEFINITE
. . . . . . . . . . -55°C to +125°C
. . . . . . . . . . -65°C to +150°C
. . . . . . . . . . . +300°C
3.5
Electrostatic discharge sensitivity, ESDS, shall be Class 1.
3.6
Electrical Performance Characteristics: The electrical performance characteristics shall be as specified in
Table I and Table II.
3.7
Electrical Test Requirements: Screening requirements shall be in accordance with 4.1 herein,
MIL-STD-883, Method 5004, and as specified in Table IV herein.
3.8
Burn-In Requirement:
3.8.1
Option 1 (TO5): Static Burn-In, Figure 5; Dynamic Burn-In, Figure 6
3.8.2
Option 2 (Glass Sealed Flatpack) : Static Burn-In / Dynamic Burn-In,
Figure 7.
3.9
Delta Limit Requirement: Delta limit parameters are specified in Table III herein, are calculated after
each burn-in, and the delta rejects are included in the PDA calculation.
3.10
Design, Construction, and Physical Dimensions: Detail design, construction, physical dimensions, and
electrical requirements shall be specified herein.
3.10.1 Mechanical / Packaging Requirements: Case outlines and dimensions are in accordance with
Figure 1, Figure 2.
3.10.2 Terminal Connections: The terminal connections shall be as specified in Figure 3, Figure 4.
3.10.3 Lead Material and Finish: The lead material and finish for Device Options 1, shall be Kovar and
options 2 are Alloy 42. The lead finishes shall be hot solder dip (Finish letter A) in accordance
with MIL-PRF-38535.
3.11
Radiation Hardness Assurance (RHA):
3.11.1 The manufacturer shall perform a lot sample test as an internal process monitor for total dose
radiation tolerance. The sample test is performed with MIL-STD-883 TM1019 Condition A as a
guideline.
3.11.2 For guaranteed radiation performance to MIL-STD-883, Method 1019, total dose irradiation, the
manufacturer will provide certified RAD testing and report through an independent test laboratory
when required as a customer purchase order line item.
3.11.3 Total dose bias circuit is specified in Figure 8.
LINEAR TECHNOLOGY CORPORATION
Page 4 of 15
SPEC NO. 05-08-5019 REV. T
4.0
RH1056A, PRECISION, HIGH SPEED, JFET INPUT OPERATIONAL AMPLIFIER
3.12
Wafer Lot Acceptance: Wafer lot acceptance shall be in accordance with MIL-PRF-38535, Appendix A,
except for the following: Topside glassivation thickness shall be a minimum of 4KÅ.
3.13
Wafer Lot Acceptance Report: SEM is performed per MIL-STD-883, Method 2018 and copies of SEM
photographs shall be supplied with the Wafer Lot Acceptance Report as part of a Space Data Pack when
specified as a customer purchase order line item.
VERIFICATION (QUALITY ASSURANCE PROVISIONS)
4.1
Quality Assurance Provisions: Quality Assurance provisions shall be in accordance with MIL-PRF-38535.
Linear Technology is a QML certified company and all Rad Hard candidates are assembled on qualified
Class S manufacturing lines.
4.2
Sampling and Inspection: Sampling and Inspection shall be in accordance with MIL-STD-883, Method
5005 with QML allowed and TRB approved deviations in conjunction with paragraphs 3.1.1, 3.2.1, and
3.4 of the test method.
4.3
Screening: Screening requirements shall be in accordance with MIL-STD-883, Method 5004 with QML
allowed and TRB approved deviations in conjunction with paragraphs 3.1, 3.1.1, and 3.4 of the test
method. Electrical testing shall be as specified in Table IV herein.
4.3.1
4.4
Analysis of catastrophic (open/short) failures from burn-in will be conducted only when a lot fails
the burn-in or re-burn-in PDA requirements.
Quality Conformance Inspection: Quality conformance inspection shall be in accordance with 4.2 and 4.3
herein and as follows:
4.4.1
Group A Inspection: Group A inspection shall be performed in accordance with 4.1 herein, per
MIL-STD-883, Method 5005, and specified in Table IV herein.
4.4.2
Group B Inspection: When purchased, a full Group B is performed on an inspection lot. As a
minimum, Subgroups 1-4 plus 6 are performed on every assembly lot, and Subgroup B2
(Resistance to Solvents / Mark Permanency) and Subgroup B3 (Solderability) are performed prior
to the first shipment from any inspection lot and Attributes provided when a Full Space Data Pack
is ordered. Subgroup B5 (Operating Life) is performed on each wafer lot. This subgroup may or
may not be from devices built in the same package style as the current inspection lot. Attributes
and variables data for this subgroup will be provided upon request at no charge.
4.4.2.1
Group B, Subgroup 2c = 10%
Group B, Subgroup 3 = 10%
Group B, Subgroup 4 = 5%
4.4.2.2
4.4.3
Group B, Subgroup 5 = *5%
(*per wafer or inspection lot
whichever is the larger quantity)
Group B, Subgroup 6 = 15%
All footnotes pertaining to Table IIa in MIL-STD-883, Method 5005 apply. The
quantity (accept number) of all other subgroups are per MIL-STD-883, Method 5005,
Table IIa.
Group D Inspection: When purchased, a full Group D is performed on an inspection lot. As a
minimum, periodic full Group D sampling is performed on each package family for each assembly
location every 26 weeks. A generic Group D Summary is provided when a full Space Data Pack is
ordered.
LINEAR TECHNOLOGY CORPORATION
Page 5 of 15
SPEC NO. 05-08-5019 REV. T
4.5
4.6
RH1056A, PRECISION, HIGH SPEED, JFET INPUT OPERATIONAL AMPLIFIER
4.4.3.1
Group D, Subgroups 3, 4 and 5 = 15% each (Sample Size Series).
4.4.3.2
All footnotes pertaining to Table IV in MIL-STD-883, Method 5005 apply. The
quantity (accept number) or sample number and accept number of all other subgroups
are per MIL-STD-883, Method 5005, Table IV.
Source Inspection:
4.5.1
The manufacturer will coordinate Source Inspection at wafer lot acceptance and pre-seal internal
visual.
4.5.2
The procuring activity has the right to perform source inspection at the supplier’s facility prior to
shipment for each lot of deliverables when specified as a customer purchase order line item. This
may include wafer lot acceptance and final data review.
Deliverable Data: Deliverable data that will ship with devices when a Space Data Pack is ordered:
4.6.1
Lot Serial Number Sheets identifying all devices accepted through final inspection by serial
number.
4.6.2
100% attributes (completed lot specific traveler; includes Group A Summary)
4.6.3
Burn-In Variables Data and Deltas (if applicable)
4.6.4
Group B2, B3, and B5 Attributes (Variables data, if performed on lot shipping)
4.6.5
Generic Group D data (4.4.3 herein)
4.6.6
SEM photographs (3.13 herein)
4.6.7
Wafer Lot Acceptance Report (3.13 herein)
4.6.8
X-Ray Negatives and Radiographic Report
4.6.9
A copy of outside test laboratory radiation report if ordered
4.6.10 Certificate of Conformance certifying that the devices meet all the requirements of this
specification and have successfully completed the mandatory tests and inspections herein.
Note: Items 4.6.1 and 4.6.10 will be delivered as a minimum, with each shipment. This is noted
on the Purchase Order Review Form as “No Charge Data”.
5.0
Packaging Requirements: Packaging shall be in accordance with Appendix A of MIL-PRF-38535. All devices
shall be packaged in conductive material or packaged in anti-static material with an external conductive field
shielding barrier.
LINEAR TECHNOLOGY CORPORATION
Page 6 of 15
SPEC NO. 05-08-5019 REV. T
RH1056A, PRECISION, HIGH SPEED, JFET INPUT OPERATIONAL AMPLIFIER
DEVICE OPTION # 1
(H) TO5 / 8 LEADS CASE OUTLINE
θja = +150°C/W
θjc = +40°C/W
FIGURE 1
LINEAR TECHNOLOGY CORPORATION
Page 7 of 15
SPEC NO. 05-08-5019 REV. T
RH1056A, PRECISION, HIGH SPEED, JFET INPUT OPERATIONAL AMPLIFIER
DEVICE OPTION # 2
(W10) GLASS SEALED FLATPACK / 10LEADS CASE OUTLINE
NOTE: 1. THIS DIMENSION ALLOWS FOR OFFCENTER LID, MENISCUS AND GLASS OVER RUN.
NOTE: 2. INCREASE DIMENSION BY 0.003 INCH
WHEN LEAD FINISH IS APPLIED (SOLDER DIPPED).
θja = +170°C/W
θjc = +40°C/W
FIGURE 2
LINEAR TECHNOLOGY CORPORATION
Page 8 of 15
SPEC NO. 05-08-5019 REV. T
RH1056A, PRECISION, HIGH SPEED, JFET INPUT OPERATIONAL AMPLIFIER
TERMINAL CONNECTIONS
FIGURE 3
FIGURE 4
LINEAR TECHNOLOGY CORPORATION
Page 9 of 15
SPEC NO. 05-08-5019 REV. T
RH1056A, PRECISION, HIGH SPEED, JFET INPUT OPERATIONAL AMPLIFIER
STATIC BURN-IN CIRCUIT
OPTION 1, TO5 METAL CAN / 8 LEADS
FIGURE 5
LINEAR TECHNOLOGY CORPORATION
Page 10 of 15
SPEC NO. 05-08-5019 REV. T
RH1056A, PRECISION, HIGH SPEED, JFET INPUT OPERATIONAL AMPLIFIER
DYNAMIC BURN-IN CIRCUIT
OPTION 1, TO5 METAL CAN / 8 LEADS
FIGURE 6
LINEAR TECHNOLOGY CORPORATION
Page 11 of 15
SPEC NO. 05-08-5019 REV. T
RH1056A, PRECISION, HIGH SPEED, JFET INPUT OPERATIONAL AMPLIFIER
STATIC/DYNAMIC BURN-IN CIRCUIT
OPTION 2, GLASS SEALED FLATPACK / 10 LEAD
FIGURE 7
LINEAR TECHNOLOGY CORPORATION
Page 12 of 15
SPEC NO. 05-08-5019 REV. T
RH1056A, PRECISION, HIGH SPEED, JFET INPUT OPERATIONAL AMPLIFIER
TOTAL DOSE BIAS CIRCUIT
FIGURE 8
LINEAR TECHNOLOGY CORPORATION
Page 13 of 15
SPEC NO. 05-08-5019 REV. T
RH1056A, PRECISION, HIGH SPEED, JFET INPUT OPERATIONAL AMPLIFIER
TABLE I: ELECTRICAL CHARACTERISTICS (PRE-IRRADIATION) NOTE (3)
TABLE II: ELECTRICAL CHARACTERISTICS (POST-IRRADIATION) NOTE (5)
ALL NOTES FOR THE ELECTRICAL CHARACTERISTICS ARE ON THE NEXT PAGE (15).
LINEAR TECHNOLOGY CORPORATION
Page 14 of 15
SPEC NO. 05-08-5019 REV. T
RH1056A, PRECISION, HIGH SPEED, JFET INPUT OPERATIONAL AMPLIFIER
TABLE I AND TABLE II ELECTRICAL CHARACTERISTICS NOTES
TABLE III: POST BURN-IN ENDPOINTS AND DELTA LIMIT REQUIREMENTS
TA = 25°C
PARAMETER
+IB
-IB
ENDPOINT LIMIT
MIN
MAX
-50
50
-50
50
DELTA
MIN
-50
-50
MAX
50
50
UNITS
pA
pA
TABLE IV: ELECTRICAL TEST REQUIREMENTS
LINEAR TECHNOLOGY CORPORATION
Page 15 of 15