DICE/DWF SPECIFICATION RH1084MK 5A Low Dropout Positive Adjustable Regulator PAD FUNCTION DIE CROSS REFERENCE 1. VIN 2. VOUT 3. ADJUST Order DICE CANDIDATE Part Number Below 2 Please refer to LTC standard product data sheet for other applicable product information. *DWF = DICE in wafer form. 1 1 RH1084MK DICE RH1084MK DWF* 2 2 3 120mils × 121mils Backside metal: Alloyed gold layer Backside potential: substrate to Pad 2 L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners. DICE/DWF ELECTRICAL TEST LIMITS PARAMETER Reference Voltage CONDITIONS NOTES MIN MAX UNITS IOUT = 10mA, (VIN – VOUT) = 3V 1.238 1.262 V 10mA ≤ IOUT ≤ 50mA 1.5V ≤ (VIN – VOUT) ≤ 25V 1.225 1.270 V Line Regulation IOUT = 10mA, 1.5V ≤ (VIN – VOUT) ≤ 15V 15V ≤ (VIN – VOUT) ≤ 30V 1, 2 0.2 0.5 % % Load Regulation (VIN – VOUT) = 3V 10mA ≤ IOUT ≤ 50mA 1, 2 0.35 % Dropout Voltage )VREF = 1%, IOUT = 50mA 1.5 V Current Limit (VIN – VOUT) = 5V Minimum Load Current (VIN – VOUT) = 25V 10 ADJUST Pin Current TJ = 25°C 120 µA ADJUST Pin Current Change 10mA ≤ IOUT ≤ 50mA 1.5V ≤ (VIN – VOUT) ≤ 25V 5 µA Note 1: See the LT®1084 data sheet thermal regulation specifications for changes in output voltage due to heating effects. Line and load regulation are measured at a constant junction temperature by low duty cycle pulse testing. Note 2: Power dissipation is determined by the input/output differential voltage and the output current. 3 5.5 A mA Note 3: Dropout voltage is tested at 50mA but guaranteed over the full output current range of the device. Test points and limits are shown on the Dropout Voltage curve in the LT1084 data sheet. Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 1 DICE/DWF SPECIFICATION RH1084MK Rad Hard die require special handling as compared to standard IC chips. Rad Hard die are susceptible to surface damage because there is no silicon nitride passivation as on standard die. Silicon nitride protects the die surface from scratches by its hard and dense properties. The passivation on Rad Hard die is silicon dioxide that is much “softer” than silicon nitride. LTC recommends that die handling be performed with extreme care so as to protect the die surface from scratches. If the need arises to move the die around from the chip tray, use a Teflon-tipped vacuum wand. This wand can be made by pushing a small diameter Teflon tubing onto the tip of a steel-tipped wand. The inside diameter of the Teflon tip should match the die size for efficient pickup. The tip of the Teflon should be cut square and flat to ensure good vacuum to die surface. Ensure the Teflon tip remains clean from debris by inspecting under stereoscope. During die attach, care must be exercised to ensure no tweezers touch the top of the die. Wafer level testing is performed per the indicated specifications for dice. Considerable differences in performance can often be observed for dice versus packaged units due to the influences of packaging and assembly on certain devices and/or parameters. Please consult factory for more information on dice performance and lot qualifications via lot sampling test procedures. Dice data sheet subject to change. Please consult factory for current revision in production. I.D.No. 66-13-1084mk 2 Linear Technology Corporation LT 0811 Rev A • PRINTED IN USA (408) 432-1900 O FAX: (408) 434-0507 O www.linear.com © LINEAR TECHNOLOGY CORPORATION 2008 1630 McCarthy Blvd., Milpitas, CA 95035-7417