PHILIPS PCF5077T

INTEGRATED CIRCUITS
DATA SHEET
PCF5077T
Power amplifier controller for GSM
and PCN systems
Preliminary specification
File under Integrated Circuits, IC17
1997 Nov 19
Philips Semiconductors
Preliminary specification
Power amplifier controller for GSM and
PCN systems
PCF5077T
FEATURES
• Programmable temperature matching
• CMOS low-voltage, low-power
• Dual supply concept for analog and digital part
• Can be used in burst mode with power-down
• No external filter for suppression of clock pulse feed
through
• 3-wire serial bus interface with the bus available in
Power-down mode
• Direct power control with ramping function (control loop
can be switched off)
• On-chip ramp generator for 256 different power levels
with two dynamic ranges
• On-chip Power-on reset for all registers
• Serial bus is compatible to bus systems independent of
additional clock pulse after rising edge of strobe signal
• Two programmable regulator start conditions (VKICK
and VHOME)
• Programmable analog output voltage limitation
• Low operating current consumption
• Ramping speed depending on the 13 MHz system
frequency clock for Global System for Mobile
communications (GSM) and Personal Communications
Network (PCN)
• TTL compatible interface
• Programmable gain factor for sensor signal at OP1
• Two different voltages for 1 LSB of the burst power
Digital-to-Analog Converter (DAC) are programmable.
• Low swing input buffer for the 13 MHz master clock
• Compatible to a large number of different RF power
modules
QUICK REFERENCE DATA
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
VDDD
digital supply voltage
note 1
2.7
3.0
6.0
V
VDDA1
analog supply voltage 1
note 1
2.7
3.0
6.0
V
VDDA2
analog supply voltage 2 (for OP4)
2.7
5.0
6.0
V
IDD(oper)(tot)
total operating current on the VDD pins
−
9
18
mA
Tamb
operating ambient temperature
−40
−
+85
°C
note 2
Notes
1. The voltages VDDA1 and VDDD must be equal and VDDA2 must be either equal or greater than VDDA1 = VDDD.
2. VDDA1 = VDDD = 3 V and VDDA2 = 5 V. The VDD pins are: VDDA1, VDDA2 and VDDD.
ORDERING INFORMATION
TYPE
NUMBER
PCF5077T
1997 Nov 19
PACKAGE
NAME
SSOP16
DESCRIPTION
plastic shrink small outline package; 16 leads; body width 4.4 mm
2
VERSION
SOT369-1
Philips Semiconductors
Preliminary specification
Power amplifier controller for GSM and
PCN systems
PCF5077T
BLOCK DIAGRAM
C2
handbook, full pagewidth
RF input
(sensor)
voltage
control for
RF power module
VD1
R1
D1
C1
VS
BVS
VINT(N)
VINT(O)
1
4
15
14
RF-ZERO + DC
C6
BAND GAP
R2
1 kΩ
VDDA1
Ibias
4.8 pF
DR1
C5
Vref
30 µA
19.2 pF
C4
Vref
8.4 kΩ
R3
OP1
10 pF
8
3.5 kΩ
DAC8
DACA
KICKA
QRSA
Vref
QRSA
−0.8
100
mV
ANALOG
FILTER
SLOPE GENERATOR
6 + 2-bit
LIMITER REGISTER
2-bit
R9
2.8 kΩ
2.8 kΩ
R10
6
6-bit
VHOME REGISTER
R8
HPA
Vref
POWER LEVEL REGISTER 8-bit
VKICK REGISTER
OP4
DR0
−0.33
+0.33
SC-ADDER
DACA
KICKA
HPA + DC
COMPARATOR
INPUT BUFFER
1/6
SERIAL BUS INTERFACE
10
Vref
4.2 kΩ
PCF5077T
9
R5
5
kΩ
DAC6
DF0/1, DC, DR0/1, TEST
2
HPA + DC
R4
11
13
DATA
VSSA
12
3
16
6
8
CONTROL
5
7
TRIG
PD
MGK910
DF
STROBE
CLK
VDDA1
VSSD
VDDD
VDDA2
Fig.1 Block diagram.
1997 Nov 19
3
CLK13
Philips Semiconductors
Preliminary specification
Power amplifier controller for GSM and
PCN systems
PCF5077T
PINNING
SYMBOL
PIN
DESCRIPTION
VS
1
sensor signal input
DF
2
programmable 3-state output
VDDA1
3
analog supply voltage 1
BVS
4
buffered sensor signal output
VS 1
16 VDDA2
TRIG
5
trigger signal input
DF 2
15 VINT(N)
VDDD
6
digital supply voltage
VDDA1 3
14 VINT(O)
PD
7
power-down input (active LOW)
CLK13
8
13 MHz master clock input
(low-swing)
STROBE
9
serial bus strobe signal input
CLK
10
serial bus clock signal input
DATA
11
serial bus data signal input
VSSD
12
digital ground
VSSA
13
analog ground
VINT(O)
14
integrator output
VINT(N)
15
integrator inverting input
VDDA2
16
analog supply voltage 2 (for OP4)
handbook, halfpage
BVS 4
PCF5077T
TRIG 5
12 VSSD
VDDD 6
11 DATA
PD 7
10 CLK
CLK13 8
9
STROBE
MGK909
Fig.2 Pin configuration.
depending on the highest steepness of the control curve
of the power module and on the sensor attenuation.
FUNCTIONAL DESCRIPTION
General
• The maximum output voltage at pin VINT(O) to protect the
power module: the limiting value of VINT(O) can be set to
4, 3.3 or 2.55 V, depending on the contents of the limiter
register (bits Lim1 and Lim0). This limiting results in a
ringing at VINT(O) (typ. 200 mV peak-to-peak value) but it
will not be transferred to the antenna because the power
module is in saturation. The limiter register bits Lim1
and Lim0 can be used to switch off the limiter option
(see Table 5).
This CMOS device integrates operational amplifiers, two
digital-to-analog converters and a serial bus interface to
implement an ‘Integrating-Controller’ (see Fig.1). It is
designed to control both the power level and the up- and
down-ramping of GSM/PCN transmit bursts.
The GSM/PCN power-up and power-down ramping curves
are generated on-chip, using an internal clock frequency of
1
2.166 MHz  T cy = -------  , that is generated internally by

f clk 
• The home position at VINT(O): the integrator output
voltage at home position (PD = HIGH and TRIG = LOW)
is programmed by means of the VHOME register.
Bits Vh5 to Vh0 are fed into a 6-bit DAC that generates
a part of VHOME.
dividing the external 13 MHz clock signal by six.
Generally, the power amplifier is ramped-up after a rising
edge on pin TRIG and ramped-down after a falling edge.
• The temperature behaviour of the home position:
bits DVh1 and DVh0 can be used to compensate
temperature dependencies (−2 or −4 mV/K) of the
control curves of the power module. This completes the
setting of VHOME.
The content of the power level register (bits PL7 to PL0)
determines which of the 2 × 256 possible values the top of
the burst will have.
To match the controller to different power modules and
sensors several parameters must be adapted.
The following parameters influence the performance of the
transmission system:
• The KICK voltage: the 6 bits of the VKICK register
(Vk5 to Vk0) determine the differential integrator input
voltage just after a ramp-up starting signal is detected.
• The external capacitor C1 in Fig.1 determines the
maximum bandwidth of the power control loop,
1997 Nov 19
13 VSSA
4
Philips Semiconductors
Preliminary specification
Power amplifier controller for GSM and
PCN systems
The register information is written via a 3-wire serial bus
(see Sections “Serial bus programming” and “Data
format”).
PCF5077T
When the chip is used in the burst mode, it is important to
switch on the PCF5077T before the power module or the
RF power. Otherwise it is possible that a positive spike at
VINT(O) will open the power module.
The output of pin DF is for general purpose which can
have three different states (LOW, HIGH and 3-state),
depending on the values of bits DF0 and DF1 in the serial
register.
A safe value is tON = 200 µs between the switching on of
the PCF5077T and the switching on of the power module
respectively the next TRIG (see Fig.3).
Dual supply pins are provided for the analog and digital
blocks.
PD = HIGH
The whole chip is active. CLK13 clocks the internal state
machine as well as the SC-adder and slope generator.
Every change at TRIG is recognized if the master clock is
running. The contents of the serial bus registers are
processed. If the master clock is switched off during
power-up, the state machine is stopped and the output of
the SC-adder and slope generator becomes undefined.
Nevertheless, by reactivating the master clock, the output
of the SC-adder and slope generator will settle to the old
values again.
Reset function
After switching on the power supply, the on-chip reset is
active for maximal 50 µs when the rising slope of VDDD has
reached 1.5 ±0.4 V. During this reset, all controllers are
set to the home position and the registers are set to their
default values. If the supply voltage drops below the reset
threshold a constant reset will appear.
Operating conditions
PD = LOW
The analog integrating controller
The serial bus interface is operating, e.g. all registers can
be programmed but no effect will be seen on any pin.
The contents of the registers are passed to the rest of the
circuit only during power-up and with the 13 MHz master
clock applied.
The analog integrating controller consists of two
operational amplifiers (OP1 and OP4) and a comparator.
OP1 amplifies the sensor signal and OP4 is used to form
a differential integrator. The comparator is used to limit the
integrator output voltage to the value selected by bits Lim1
and Lim0 in the limiter register.
If the low-swing input buffer at pin CLK13 is switched off,
neither the SC-adder nor the slope generator will function.
This means that after the chip is powered-up, the outputs
have to settle again to the programmed register values.
The settling time is dominated by the slow power-up of the
band gap of typically 50 µs.
1997 Nov 19
A (Schottky) diode D1 as external rectifier is connected to
pin VS. The SC-adder block generates the voltage for the
ramping of the power module.The differential integrator
integrates the difference of this voltage and the voltage
detected at the diode. The integrator output voltage VINT(O)
is used to control the power amplifier module.
5
Philips Semiconductors
Preliminary specification
Power amplifier controller for GSM and
PCN systems
Table 1
PCF5077T
Definition of some voltages used in Figs 1 and 3
SYMBOL
DESCRIPTION
Vref
reference voltage, typically 1.25 V
VD1
voltage over the sensor diode D1
VPL
voltage determining the power level; it is generated in the Switched Capacitor (SC)-adder block if
switch DACA is closed (i.e. if the signal DACA is HIGH)
VVS
voltage at pin VS when RF is rectified by the sensor diode D1
VBVS
amplified voltage from pin VS
VKICK
voltage determining the kick level; it is generated in the SC-adder block if switch KICKA is closed (i.e.
if the signal KICKA is HIGH)
VHOME
voltage determining the home position voltage; if HPA signal is active, the output of DAC6 plus
temperature compensation is amplified and appears at the output of OP4 (pin VINT(O))
VQRS
low voltage at the output of the SC-adder block which causes a ramp-down with a shortened tail if
switch QRSA is closed (i.e. if the signal QRSA is HIGH)
VRFIN
input signal to the power amplifier
open (HPA + DC is either HPA switch or DC bit).
Switch HPA is closed when there is no home position.
Due to the negative differential input voltage VKICK, the
integrator output will start to rise. After 18Tcy (time C) the
output of DAC8 is connected to the SC-adder and slope
generator block. The input of the 8-bit DAC comes from
bits PL7 to PL0 in the power level register. The slope
generator will generate a smooth curve between the
former and the new output value of the SC-adder block.
The power amplifier is ramped-up via the integrator in
approximately 22Tcy.
Ramp generation (see Fig.3)
The circuit is activated with the PD signal going HIGH
before time mask AS and deactivated after ramping down,
e.g. at time GS to HS. For this usual ‘power-down burst
mode’ application in GSM/PCN mobile stations, the RF
input power at the power module must be activated
between time AS and BS (when the home position at
VINT(O) has already reached its stable value) and
deactivated between time GS and HS. This is necessary
for many types of power modules to meet the −70 dB
margin.
This condition is stable as long as TRIG remains HIGH.
Two clock periods after a falling edge at TRIG the
ramp-down is started (time E). The SC-adder output
voltage will change to VQRS (−100 mV), because DACA
becomes inactive and QRSA active. This causes a
ramp-down with a shortened tail. The slope generator
again generates a smooth curve between the new
SC-adder output voltage and the old SC-adder output
voltage.
A ramp-up is started by a rising edge of the TRIG signal.
The TRIG signal and all other internal signals are delayed
by two clock periods (2Tcy) with respect to the signal at
pin TRIG.
The timing diagram shows a possible relationship between
the chip timing (time B to G) relative to the GSM-mask
(AS to HS). However, the user is free to choose the rising
and falling edge of TRIG independently so that the mask is
not violated.
The slope generator must have reached its final value at
38Tcy after the recognized falling edge of TRIG because
the HPA signal is activated again and by that turning the
integrator into its ‘home position’ (time G). The integrator
output voltage will be regulated once more to the value
defined in the VHOME register.
DESCRIPTION OF THE SIGNALS STARTING AT A STABLE HOME
VINT(O) AT TIME B − 2Tcy
POSITION OF
The integrator output voltage is regulated to the value
defined in the VHOME register. The output of the slope
generator is connected to the negative input VINT(N) of
operational amplifier OP4 (VKICK is defined by
bits Vk5 to Vk0 in the VKICK register). Two clock periods
after a rising edge on pin TRIG, the integrator start
condition circuitry is turned off and OP4 is switched into an
integrator configuration (time B). The HPA switches will
1997 Nov 19
6
Philips Semiconductors
Preliminary specification
Power amplifier controller for GSM and
PCN systems
AS
handbook, full pagewidth
22Tcy
BS
18Tcy
CS
t1
dB
4
1
1
6
30
70
B
2Tcy
tON 200 µs
18Tcy
C
22Tcy
PCF5077T
DS
ES
22Tcy
,,,,
,,,,
,,,,
,,,,
,,,,
,,,,
,,,,
t2
(8Tcy)
E
2Tcy
FS
18Tcy
GS
22Tcy
HS
(2Tcy)
38Tcy
tOFF
G
44Tcy
TRIG
PD
KICKA
HPA
QRSA
DACA
RFIN
(7)
RF-ZERO
(1)
(2)
(3)
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(4)
(5)
(6)
MGK912
tRFON = tON − 12Tcy to tON + 2Tcy.
tRFOFF = 44Tcy to 66Tcy.
VKICK (start integrator) applied to integrator.
VPL applied to integrator.
VQRS applied to integrator.
VHOME at output of OP4.
This timing of the RF input power (from the power module) ensures that the −70 dB margin is met, even if the isolation of the power module is bad.
Fig.3 Timing diagram of a typical ramp-up/ramp-down curve.
1997 Nov 19
7
Philips Semiconductors
Preliminary specification
Power amplifier controller for GSM and
PCN systems
leading bits are ignored, and no check is made on the
number of clock pulses. The fully static CMOS design uses
virtually no current when the bus is inactive. The bus is
also programmable during power-down.
Serial bus programming
A simple 3-wire unidirectional serial bus is used to program
the circuit. The 3 wires are DATA, CLK and STROBE.
The data sent to the device is loaded in bursts framed by
STROBE. Programming clock edges and their appropriate
data bits are ignored until STROBE goes active LOW.
Data format
Data is entered with the most significant bit (MSB) first.
The leading 10 bits p15 to p6 are the data field, the
following bits p5 and p4 form the subaddress, while the
last 4 bits p3 to p0 are the device address field.
The PCF5077T uses only one of the available addresses.
The format is given in Table 2.
The last four address bits are decoded on the active
STROBE edge. This produces an internal load pulse to
store the data in one of the addressed registers. To avoid
erroneous circuit operation, the STROBE pulse is not
allowed during internal data reads by the rest of the circuit.
This condition is guaranteed by respecting a minimum
STROBE pulse width after data transfer.
The correspondence between data and address fields is
given in Table 3 and the description in Table 4.
Only the last 16 bits serially clocked into the device are
retained within the programming register. Additional
Table 2
PCF5077T
All three registers in Table 3 are set to 00H during reset.
Programming register format
DATA BITS
SUBADDRESS
MSB
DEVICE ADDRESS
LSB
p15
p14 to p8
p7
p6
p5
p4
p3
p2
p1
p0
data9
data8 to data2
data1
data0
Sadd1
Sadd0
add3
add2
add1
add0
Table 3
Register bit allocation
DATA FIELD (D9 TO D0)
SUBADDRESS
MSB
DEVICE ADDRESS
LSB
p15
p14
p13
p12
p11
p10
p9
p8
p7
p6
p5
p4
p3
p2
p1
p0
Vk5
Vk4
Vk3
Vk2
Vk1
Vk0
Lim1
Lim0
DC
Test
0
0
1
0
1
0
Vh5
Vh4
Vh3
Vh2
Vh1
Vh0
DVh1 DVh0
DR1
DR0
0
1
1
0
1
0
PL7
PL6
PL5
PL4
PL3
PL2
DF1
DF0
1
1
1
0
1
0
Table 4
PL1
PL0
Description of bits used in Table 3
BITS
DESCRIPTION
Vk5 to Vk0
6 bits to control the kick voltage in 64 steps
Vh5 to Vh0
6 bits to control the home position voltage in 64 steps
PL7 to PL0
8 bits to control the power level in 256 steps
Lim1 and Lim0
2 bits to control the limiter voltage (see Table 5)
DC
direct control with ramping function (control loop is switched off when DC = 1)
Test
test mode (Test = 1); must always be set to logic 0 in application
DVh1 and DVh0
2 bits to set the temperature coefficient of VHOME (see Table 6)
DR1
gain factor of OP1
DR0
gain factor for slope generator output
DF1
enable of the 3-state output on pin DF (for DF1 = 0, pin DF is in 3-state mode)
DF0
data output on pin DF
1997 Nov 19
8
Philips Semiconductors
Preliminary specification
Power amplifier controller for GSM and
PCN systems
Table 5
PCF5077T
Limiter voltage
Lim1
Lim0
LIMITER VOLTAGE
(V)
TOLERANCE AT Tamb = 27 °C
(mV)
TOLERANCE AT Tamb = 85 °C
(mV)
0
0
limiter off
−
−
0
1
4.00
±250
±350
1
0
3.30
±250
±350
1
1
2.55
±250
±350
Table 6
Programmable temperature coefficient of VHOME
VHOME(1)
DVh1
DVh0
0
0
Vh ±0.4 mV/K
0
1
Vh − 2 mV/K ±20%
1
0
Vh − 4 mV/K ±20%
1
1
VSS
Note
1. Vh = voltage programmed in VHOME register bits Vh5 to Vh0 and generated by DAC6.
LIMITING VALUES
In accordance with the Absolute Maximum Rating System (IEC 134).
SYMBOL
PARAMETER
MIN.
MAX.
UNIT
analog supply voltage 1
−0.5
+6.0(1)
V
analog supply voltage 2
−0.5
+6.0(1)
V
VDDD
digital supply voltage
−0.5
+6.0(1)
V
VI
DC input voltage on all pins (except pin VS)
−0.5
VDD + 0.5
V
VI(VS)
DC input voltage on pin VS
−3.0
VDD + 0.5
V
II(n)
DC input current on any signal pin
−10
+10
mA
Ptot
total power dissipation
−
83
mW
Tstg
storage temperature
−65
+150
°C
Tamb
operating ambient temperature
−40
+85
°C
VDDA1
VDDA2
Note
1. Pulses of 7 V are allowed for less than 100 ms.
1997 Nov 19
9
Philips Semiconductors
Preliminary specification
Power amplifier controller for GSM and
PCN systems
PCF5077T
OPERATING CHARACTERISTICS
VDDA1, VDDA2 and VDDD = VDD = 2.7 to 6.0 V; VDDD = VDDA1 ≤ VDDA2; Tamb = −40 to +85 °C; unless otherwise specified.
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
Operational amplifier (OP1)
VDDA1
analog supply voltage 1
2.7
3.0
6.0
V
GB
gain bandwidth product
VDDA1 = 3.0 V
2.0
−
−
MHz
Gmin
minimum gain
DR1 = 0
−8.1
−7.6
−7.1
dB
Gmax
maximum gain
DR1 = 1
5.9
6.4
6.9
dB
Voffset
offset voltage
no load at output
−20
0
+20
mV
2.7
5.0
6(1)
V
Operational amplifier (OP4)
VDDA2
analog supply voltage 2
GB
gain bandwidth product
CL = 120 pF; VDDA2 = 5 V;
note 2
4
−
−
MHz
PSRR
power supply rejection ratio
VDDA2 = 5 V, at 217 Hz
50(3)
55
−
dB
SRpos
positive slew rate
VDDA2 = 5 V; note 4
3.5
15
−
V/µs
SRneg
negative slew rate
VDDA2 = 5 V; note 4
3.5
6
−
V/µs
Voffset
voltage offset
no load at output
−20
0
+20
mV
Vo(min)
minimum output voltage
−
−
0.3
V
Vo(max)
maximum output voltage
0.85VDDA2
−
−
V
Io
output current
4.5
−
−
mA
note 5
Programmability and accuracy of VPL (DAC8) at VINT(O)
INL
integral non-linearity
−
±1.5
±10
LSB
DNL
differential non-linearity
−
±0.2
±1
LSB
Vo(min)
minimum output voltage
DC = 1; DR0 = 1; note 6
−30
−
+60
mV
Vo(max)
maximum output voltage
DC = 1; DR0 = 0; note 6
2.72
−
3.15
V
STS
step size
DC = 1; DR0 = 1
−
6
−
mV
DC = 1; DR0 = 0
−
11.7
−
mV
Programmability and accuracy of VKICK (DAC8) at VINT(O)
Vo(min)
minimum output voltage
DC = 1; DR0 = 1; note 6
−50
−
+50
mV
Vo(max)
maximum output voltage
DC = 1; DR0 = 0; note 6
270
−
400
mV
STS
step size
DC = 1; DR0 = 1
−
2.6
−
mV
DC = 1; DR0 = 0
−
5.0
−
mV
1997 Nov 19
10
Philips Semiconductors
Preliminary specification
Power amplifier controller for GSM and
PCN systems
SYMBOL
PARAMETER
PCF5077T
CONDITIONS
MIN.
TYP.
MAX.
UNIT
Programmability and accuracy of VHOME (DAC6) at VINT(O)
INL
integral non-linearity
note 7
−
±1.0
±3
LSB
DNL
differential non-linearity
note 7
−
±0.2
±1
LSB
Vo(min)
minimum output voltage
DVh1 = 0; DVh0 = 0
50
−
170
mV
Vo(max)
maximum output voltage
DVh1 = 0; DVh0 = 0
1.95
−
2.25
V
STS
step size
−
33
−
mV
Notes
1. Pulses of 7 V are allowed for less than 100 ms.
2. Minimum specified frequency at Tamb = 27 °C. For Tamb = 85 °C a typical value of 4 MHz is specified.
3. Not tested. Guaranteed by design.
4. Slew rates are measured between 10% and 90% of output voltage with a load of approximately 40 pF to ground.
5. Measured with RL = 1.2 kΩ, CL = 80 pF and VDDA2 = 5 V. The voltage drop at the output is less than 20 mV.
6. Referred to VHOME; nominal operating condition, direct control (DC = 1), VHOME programmed to 40.
7. The parameter is measured starting from code 4, due to a saturation effect for the first four codes.
1997 Nov 19
11
Philips Semiconductors
Preliminary specification
Power amplifier controller for GSM and
PCN systems
PCF5077T
DC CHARACTERISTICS
VDDA1, VDDA2 and VDDD = VDD = 2.7 to 6.0 V; VDDD = VDDA1 ≤ VDDA2; Tamb = −40 to +85 °C; unless otherwise specified.
SYMBOL
PARAMETER
CONDITIONS
MIN.
TYP.
MAX.
UNIT
VDDD
digital supply voltage
2.7
3.0
6.0
V
VDDA1
analog supply voltage 1
2.7
3.0
6.0
V
VDDA2
analog supply voltage 2
2.7
5.0
6.0
V
IDD(oper)(tot) total operating current on the VDD pins
fCLK13 = 13 MHz; see Fig.5
−
9
18
mA
IDD(idle)(tot)
PD = LOW
−
4
20
µA
−5
−
+5
µA
total idle current on the VDD pins
Logic inputs (pins TRIG, STROBE, CLK and DATA)
ILIL
LOW-level input leakage current
VIL = 0 V
ILIH
HIGH-level input leakage current
VIH = 6 V
−5
−
+5
µA
Ci
input capacitance
−
10
−
pF
VIL
LOW-level input voltage
0
−
0.2VDD V
VIH
HIGH-level input voltage
0.5VDD −
VDD
V
IOL = IOH = 3 mA
−
0.4
V
3-state output (pin DF)
−
VOL
LOW-state output voltage
VOH
HIGH-state output voltage
IOL = IOH = 3 mA
0.7VDD −
−
V
ILO
3-state output leakage current
VDF = 0 to VDD
−5
−
+5
µA
Low-swing master clock input (pin CLK13)
ILl
input leakage current
−5
−
+5
µA
Ci
input capacitance
−
10
−
pF
Zi
input impedance
fCLK13 = 13 MHz; note 1
−
5
−
kΩ
Vi(p−p)
input voltage (peak-to-peak value)
note 2
0.35
−
VDD
V
−3.0
−
VDD
V
Sensor input voltage (pin VS)
Vi(VS)
input voltage at pin VS
Band gap
Ibias
bias current (source for D1)
VVS = 0 V; Tamb = 25 °C;
TC = −0.08 µA/K
21
28
35
µA
Vref
reference voltage
Tamb = 25 °C
1.18
1.25
1.32
V
TC
temperature coefficient for Vref
tpu
power-up time for Vref
−
±170
−
ppm/K
note 3
−
5
50
µs
Tamb = 25 °C;
TC = −4 mV/K
1.2
1.5
1.8
V
−
−
50
µs
Power-on reset, threshold voltage Vth; see Fig.4
Vth
threshold voltage
trst
reset time
Notes
1. An AC coupling with 33 pF is recommended.
2. Tested at nominal working condition (VDDD = VDDA1 = 3 V; VDDA2 = 5 V). AC coupling = 33 pF.
3. The necessary start-up time tON = 200 µs (see Fig.3) between PD and TRIG is more than tpu.
1997 Nov 19
12
Philips Semiconductors
Preliminary specification
Power amplifier controller for GSM and
PCN systems
PCF5077T
handbook, halfpage
VDDD
Vth
t
< trst
internal
reset
t
MGK914
Fig.4 Timing diagram for on-chip reset function.
MGK916
8
handbook, halfpage
IDD
(mA)
(1)
6
4
(2)
2
(3)
0
3
(1) IDDA1.
(2) IDDA2.
4
5
VDD (V)
6
(3) IDDD.
Fig.5 Operating current IDD as a function of VDD.
1997 Nov 19
13
Philips Semiconductors
Preliminary specification
Power amplifier controller for GSM and
PCN systems
PCF5077T
TIMING CHARACTERISTICS
VDDA1, VDDA2 and VDDD = 2.7 to 6.0 V; VDDD = VDDA1 ≤ VDDA2; Tamb = −40 to +85 °C; unless otherwise specified.
SYMBOL
PARAMETER
MIN.
TYP.
UNIT
Controller timing; see Fig.3
td(TRIG-B)
delay from positive TRIG edge to time B = 13⁄6Tcy
−
1.0
µs
td(B-C)
delay from time B to time C = 18Tcy
−
8.31
µs
−
1.0
µs
−
17.54
µs
td(TRIG-E)
delay from negative TRIG edge to time E =
td(E-G)
delay from time E to time G = 38Tcy
13⁄
6Tcy
Serial bus timing; see Fig.6
SERIAL PROGRAMMING CLOCK (PIN CLK)
tr
rise time
−
10
ns
tf
fall time
−
10
ns
Tcy
clock period
100
−
ns
ENABLE PROGRAMMING (PIN STROBE)
tstart
strobe start time to first clock edge
0
−
ns
tend
strobe end time after last clock edge
40
−
ns
REGISTER SERIAL INPUT DATA (PIN DATA)
tsu
input data to CLK set-up time
20
−
ns
th
input data to CLK hold time
20
−
ns
tsu
handbook, full pagewidth
Tcy
th
CLK
DATA
MSB
LSB
STROBE
tend
tstart
Fig.6 Serial bus timing diagram.
1997 Nov 19
14
MGK913
Philips Semiconductors
Preliminary specification
Power amplifier controller for GSM and
PCN systems
When DR1 = 1, the control loop regulates the output
power of the PA to a lower power level. A dynamic range
of about 10 dBm can be switched by this manner.
APPLICATION INFORMATION
Direct power control with ramping function (DC = 1)
The circuit offers a useful feature to control power levels
close to the saturation region of the external power
module.
Vs : Vpeak is the ratio of sensor signal to slope generator
output voltage effective at the integrator output (OP4).
Table 7
This flexibility consists in the direct control on the power
level by setting bit DC to logic 1.
In this condition, the external control loop is switched off by
disabling the gain path from OP1. The ramping shape of
the signal to be transmitted as well as its final level are
driven only by the internally generated control signal from
the slope generator. In this way transient effects to recover
active components from deep saturation are avoided.
The relative error on the absolute value of output power is
quite limited, as a power amplifier is less sensitive to
temperature variation in its saturated region. However, this
way of operating may increase the phase error.
Gain factors
DR1
DR0
VS : Vpeak
0
0
1:1
0
1
2:1
1
0
5:1
1
1
10 : 1
Additional application information
Evaluation kits with software and demonstration board are
available for the PCF5077T together with Philips power
modules BGY206, CGY2010, CGY2020 and CGY2021 for
GSM and PCN, which will provide help for applications.
Increased dynamic range
Very little bus traffic is required for the PCF5077T because
the ramping curves are generated on-chip. VKICK and
VHOME define the start conditions for up-ramping.
VPL determines the power levels. TRIG is the trigger for up
and down-ramping.
The PCF5077T is able to control a dynamic range of
30 dBm by switching the gain factor of the sensor amplifier
and the resolution of DAC8. This range corresponds to a
maximum peak-to-peak voltage of 3 V measured at the
sensor diode. Figure 7 shows the voltage at the sensor
diode (VS) versus the output power (P) of the Power
Amplifier (PA) with a directional coupler of 20 dB
attenuation. The maximum voltage of 3 V is reached when
the output power is 35 dBm.
The non-linear behaviour of the control curves of the
power modules have a big influence on the loop. Start
conditions in the flat area of the control curve are critical
and need some attention. Initially VINT(O) will be at the
home position. The HPA switches release the regulator.
The integrator is moved into the active part of the control
curve. This is achieved by integrating VKICK. When VINT(O)
has reached the active region of the control curve the loop
is closed and the circuit is able to follow the ramping
function generated by a voltage step to the slope
generator. The step height VPL determines the power of
the transmit burst. Down-ramping is started at the slope
generator input by a voltage step from VPL back to VQRS.
The loop follows the leading function for down-ramping
until the RF sensor measures zero. The reason for VQRS is
to shorten the tail of the slope.
The sensor voltage for power level lower than 13 dBm, as
necessary for GSM Phase 2 and DCS1800, is lower than
200 mV. An 8-bit DAC would not be sufficient to cover the
complete dynamic range. Therefore bits DR0 and DR1 are
used to switch the power range that can be controlled with
the controller (see Table 7).
REDUCED VOLTAGE STEPS OF POWER LEVEL DAC8
(DR0 = 1)
The DR0 bit is used to switch resistor R9 (switch DR0 is
closed) at the integrator input (OP4). The ratio of the DAC8
range to the sensor signal voltage is therefore halved and
the power corresponding to one LSB of DAC8 is reduced
by 3 dB. With this setting the power module can be
controlled more accurately for low output power levels.
Figures 8 and 9 show the results of measurements on the
up and down-ramping where REF is the reference level of
the power in the time slot, ATTEN is the attenuation of the
input instrument for not to destroy the instrument itself,
RES BW is the resolution bandwidth, VBW is the video
bandwidth, CENTER is the carrier frequency for the burst
that has been measured and SWP is the sweep time used
for the measurement.
GAIN FACTOR OF OP1 (DR1)
Bit DR1 switches (switch DR1 is closed) the ratio of the
capacitances at OP1. The gain factor for the sensor
amplifier is five times higher when DR1 is in high state.
1997 Nov 19
PCF5077T
15
Philips Semiconductors
Preliminary specification
Power amplifier controller for GSM and
PCN systems
PCF5077T
VKICK must be reduced for low level of VPL to avoid that
both voltages become equal. Setting VKICK to minimum
value for the lowest power level can be sufficient.
ADJUSTMENT OF THE HOME POSITION
The 6-bit DAC for VHOME determines the start point of the
burst in the time template. Curve 2 in Fig.8 shows what
happens when VHOME is too low. The burst starts too late
and the up-ramping of the power is too steep. The steep
up-ramping results in a wide transient spectra. The RF
input power shall be switched off when the TRIG signal is
LOW to keep the −70 dB margin before the burst.
At low power level the burst will start later because of the
bend sensor curve (see Fig.7). The trigger pulse has to be
started up to 3 bits earlier for the lowest power level to
avoid that the power is ramped up too late for the first data
bits of the burst.
The home position has to be adjusted for each mobile
phone because of DAC tolerances and individual PA
characteristics.
LIMIT FOR CORRECT DOWN-RAMPING
The maximum RF power that the power module in
saturation is able to deliver depends on RF input power,
transmit frequency, supply voltage, temperature and load
impedance. The maximum VPL must be matched to the
worst case output power and then reduced by 1 dB when
the PCF5077T is used in closed loop mode.
The temperature coefficients for VHOME (−2 and −4 mV/K)
are used to compensate the temperature shift of the PA
control curve. Therefore the PA and the controller shall be
placed nearby on the printed-circuit board. Additionally it
has to be considered that the temperature of the PA and
PCF5077T are different because the PA heats up itself.
Software may help to adapt VHOME to different
temperatures.
Curve 2 in Fig.9 shows what happens when the PA is
driven into saturation. The down-ramping of the power is
getting too steep and therefore the transient spectra will be
too wide. The 1 dB margin is necessary because of the flat
PA control curve at high power level. The loop needs more
time to reduce the power during the down-ramping and the
control voltage increases. The high control voltage forces
the power quickly down when the steep region of the
control curve is achieved. The steep down-ramping results
in a wide transient spectra.
ADJUSTMENT OF VKICK
After the falling edge of HPA the integrator starts to
increase the control voltage up to the position of VKICK
where the PA should have reached its active region.
Increasing VKICK at high power level makes the up ramping
of the burst smoother and improves the transient spectra.
MGK915
10
handbook, halfpage
VS
(V)
1
10−1
10−2
−5
0
5
10
15
20
25
30
35
P (dBm)
Fig.7 Sensor voltage as a function of output power (diode BAT62).
1997 Nov 19
16
Philips Semiconductors
Preliminary specification
Power amplifier controller for GSM and
PCN systems
REF 33.4 dBm
PCF5077T
ATTEN 40 dB
+4 dB
+1 dB
handbook, full pagewidth
LOG
10
dB/
6 dB
MBE718
1 dB
KICK
30 dB
1
2
70 dB
40
28
CENTER 902.400 MHz
# RES BW 300 kHz
18
0 µs
10
32
# SWP 80 µs
# VBW 300 kHz
(1) Highest usable value.
(2) Lowest usable value.
Fig.8 Power as a function of time; rising edge (behaviour at different worst case home positions of VINT(O)).
handbook, full pagewidth
REF 34.8 dBm
ATTEN 40 dB
MBE719
LOG
10
dB/
2
1
6 dB
30 dB
70 dB
543 µs
CENTER 902.400 MHz
# RES BW 1.0 MHz
553
561
571
# VBW 300 kHz
(1) Correct behaviour.
(2) Unusable behaviour with wrong VPL value.
Fig.9 Power as a function of time; falling edge.
1997 Nov 19
17
591
# SWP 80 µs
Philips Semiconductors
Preliminary specification
Power amplifier controller for GSM and
PCN systems
The sensor voltage of 3 V at pin VS corresponds to the
maximum DAC output voltage. The power range that can
be controlled is therefore not limited by the sensor voltage
input VS and higher power levels can be controlled with
the control loop switched on.
Application in mobile stations
Using a directional coupler with 16.5 dB attenuation
produces a sensor signal between 100 mV and 3 V below
the diode forward voltage at pin VS for the PA output
power range of 8 to 36 dBm.
handbook, full pagewidth
PCF5077T
antenna
RF POWER
AMPLIFIER
sensor
C2
8.2 to 39 pF
R1
1 kΩ
D1
VS
TRIG
PD
C3
CLK13
1
16
2
15
3
14
4
13
PCF5077T
5
12
6
11
7
10
8
9
33 pF
VINT(N)
C1
VINT(O)
120 pF
VSSA
VSSD
DATA
CLK
STROBE
3-wire
serial
bus
MGK911
Fig.10 Application diagram for mobile stations.
1997 Nov 19
18
RF
Philips Semiconductors
Preliminary specification
Power amplifier controller for GSM and
PCN systems
PCF5077T
PACKAGE OUTLINE
SSOP16: plastic shrink small outline package; 16 leads; body width 4.4 mm
D
SOT369-1
E
A
X
c
y
HE
v M A
Z
9
16
Q
A2
A
(A 3)
A1
pin 1 index
θ
Lp
L
1
8
detail X
w M
bp
e
0
2.5
5 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A
max.
A1
A2
A3
bp
c
D (1)
E (1)
e
HE
L
Lp
Q
v
w
y
Z (1)
θ
mm
1.5
0.15
0.00
1.4
1.2
0.25
0.32
0.20
0.25
0.13
5.30
5.10
4.5
4.3
0.65
6.6
6.2
1.0
0.75
0.45
0.65
0.45
0.2
0.13
0.1
0.48
0.18
10
0o
Note
1. Plastic or metal protrusions of 0.20 mm maximum per side are not included.
OUTLINE
VERSION
REFERENCES
IEC
JEDEC
EIAJ
ISSUE DATE
94-04-20
95-02-04
SOT369-1
1997 Nov 19
EUROPEAN
PROJECTION
19
o
Philips Semiconductors
Preliminary specification
Power amplifier controller for GSM and
PCN systems
If wave soldering cannot be avoided, the following
conditions must be observed:
SOLDERING
Introduction
• A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave)
soldering technique should be used.
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
• The longitudinal axis of the package footprint must
be parallel to the solder flow and must incorporate
solder thieves at the downstream end.
Even with these conditions, only consider wave
soldering SSOP packages that have a body width of
4.4 mm, that is SSOP16 (SOT369-1) or
SSOP20 (SOT266-1).
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “IC Package Databook” (order code 9398 652 90011).
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Reflow soldering
Reflow soldering techniques are suitable for all SSOP
packages.
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Maximum permissible solder temperature is 260 °C, and
maximum duration of package immersion in solder is
10 seconds, if cooled to less than 150 °C within
6 seconds. Typical dwell time is 4 seconds at 250 °C.
Several techniques exist for reflowing; for example,
thermal conduction by heated belt. Dwell times vary
between 50 and 300 seconds depending on heating
method. Typical reflow temperatures range from
215 to 250 °C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
Repairing soldered joints
Fix the component by first soldering two diagonallyopposite end leads. Use only a low voltage soldering iron
(less than 24 V) applied to the flat part of the lead. Contact
time must be limited to 10 seconds at up to 300 °C. When
using a dedicated tool, all other leads can be soldered in
one operation within 2 to 5 seconds between
270 and 320 °C.
Preheating is necessary to dry the paste and evaporate
the binding agent. Preheating duration: 45 minutes at
45 °C.
Wave soldering
Wave soldering is not recommended for SSOP packages.
This is because of the likelihood of solder bridging due to
closely-spaced leads and the possibility of incomplete
solder penetration in multi-lead devices.
1997 Nov 19
PCF5077T
20
Philips Semiconductors
Preliminary specification
Power amplifier controller for GSM and
PCN systems
PCF5077T
DEFINITIONS
Data sheet status
Objective specification
This data sheet contains target or goal specifications for product development.
Preliminary specification
This data sheet contains preliminary data; supplementary data may be published later.
Product specification
This data sheet contains final product specifications.
Limiting values
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or
more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation
of the device at these or at any other conditions above those given in the Characteristics sections of the specification
is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.
LIFE SUPPORT APPLICATIONS
These products are not designed for use in life support appliances, devices, or systems where malfunction of these
products can reasonably be expected to result in personal injury. Philips customers using or selling these products for
use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such
improper use or sale.
1997 Nov 19
21
Philips Semiconductors
Preliminary specification
Power amplifier controller for GSM and
PCN systems
NOTES
1997 Nov 19
22
PCF5077T
Philips Semiconductors
Preliminary specification
Power amplifier controller for GSM and
PCN systems
NOTES
1997 Nov 19
23
PCF5077T
Philips Semiconductors – a worldwide company
Argentina: see South America
Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113,
Tel. +61 2 9805 4455, Fax. +61 2 9805 4466
Austria: Computerstr. 6, A-1101 WIEN, P.O. Box 213, Tel. +43 160 1010,
Fax. +43 160 101 1210
Belarus: Hotel Minsk Business Center, Bld. 3, r. 1211, Volodarski Str. 6,
220050 MINSK, Tel. +375 172 200 733, Fax. +375 172 200 773
Belgium: see The Netherlands
Brazil: see South America
Bulgaria: Philips Bulgaria Ltd., Energoproject, 15th floor,
51 James Bourchier Blvd., 1407 SOFIA,
Tel. +359 2 689 211, Fax. +359 2 689 102
Canada: PHILIPS SEMICONDUCTORS/COMPONENTS,
Tel. +1 800 234 7381
China/Hong Kong: 501 Hong Kong Industrial Technology Centre,
72 Tat Chee Avenue, Kowloon Tong, HONG KONG,
Tel. +852 2319 7888, Fax. +852 2319 7700
Colombia: see South America
Czech Republic: see Austria
Denmark: Prags Boulevard 80, PB 1919, DK-2300 COPENHAGEN S,
Tel. +45 32 88 2636, Fax. +45 31 57 0044
Finland: Sinikalliontie 3, FIN-02630 ESPOO,
Tel. +358 9 615800, Fax. +358 9 61580920
France: 51 Rue Carnot, BP317, 92156 SURESNES Cedex,
Tel. +33 1 40 99 6161, Fax. +33 1 40 99 6427
Germany: Hammerbrookstraße 69, D-20097 HAMBURG,
Tel. +49 40 23 53 60, Fax. +49 40 23 536 300
Greece: No. 15, 25th March Street, GR 17778 TAVROS/ATHENS,
Tel. +30 1 4894 339/239, Fax. +30 1 4814 240
Hungary: see Austria
India: Philips INDIA Ltd, Band Box Building, 2nd floor,
254-D, Dr. Annie Besant Road, Worli, MUMBAI 400 025,
Tel. +91 22 493 8541, Fax. +91 22 493 0966
Indonesia: see Singapore
Ireland: Newstead, Clonskeagh, DUBLIN 14,
Tel. +353 1 7640 000, Fax. +353 1 7640 200
Israel: RAPAC Electronics, 7 Kehilat Saloniki St, PO Box 18053,
TEL AVIV 61180, Tel. +972 3 645 0444, Fax. +972 3 649 1007
Italy: PHILIPS SEMICONDUCTORS, Piazza IV Novembre 3,
20124 MILANO, Tel. +39 2 6752 2531, Fax. +39 2 6752 2557
Japan: Philips Bldg 13-37, Kohnan 2-chome, Minato-ku, TOKYO 108,
Tel. +81 3 3740 5130, Fax. +81 3 3740 5077
Korea: Philips House, 260-199 Itaewon-dong, Yongsan-ku, SEOUL,
Tel. +82 2 709 1412, Fax. +82 2 709 1415
Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA, SELANGOR,
Tel. +60 3 750 5214, Fax. +60 3 757 4880
Mexico: 5900 Gateway East, Suite 200, EL PASO, TEXAS 79905,
Tel. +9-5 800 234 7381
Middle East: see Italy
Netherlands: Postbus 90050, 5600 PB EINDHOVEN, Bldg. VB,
Tel. +31 40 27 82785, Fax. +31 40 27 88399
New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND,
Tel. +64 9 849 4160, Fax. +64 9 849 7811
Norway: Box 1, Manglerud 0612, OSLO,
Tel. +47 22 74 8000, Fax. +47 22 74 8341
Philippines: Philips Semiconductors Philippines Inc.,
106 Valero St. Salcedo Village, P.O. Box 2108 MCC, MAKATI,
Metro MANILA, Tel. +63 2 816 6380, Fax. +63 2 817 3474
Poland: Ul. Lukiska 10, PL 04-123 WARSZAWA,
Tel. +48 22 612 2831, Fax. +48 22 612 2327
Portugal: see Spain
Romania: see Italy
Russia: Philips Russia, Ul. Usatcheva 35A, 119048 MOSCOW,
Tel. +7 095 755 6918, Fax. +7 095 755 6919
Singapore: Lorong 1, Toa Payoh, SINGAPORE 1231,
Tel. +65 350 2538, Fax. +65 251 6500
Slovakia: see Austria
Slovenia: see Italy
South Africa: S.A. PHILIPS Pty Ltd., 195-215 Main Road Martindale,
2092 JOHANNESBURG, P.O. Box 7430 Johannesburg 2000,
Tel. +27 11 470 5911, Fax. +27 11 470 5494
South America: Al. Vicente Pinzon, 173, 6th floor,
04547-130 SÃO PAULO, SP, Brazil,
Tel. +55 11 821 2333, Fax. +55 11 821 2382
Spain: Balmes 22, 08007 BARCELONA,
Tel. +34 3 301 6312, Fax. +34 3 301 4107
Sweden: Kottbygatan 7, Akalla, S-16485 STOCKHOLM,
Tel. +46 8 632 2000, Fax. +46 8 632 2745
Switzerland: Allmendstrasse 140, CH-8027 ZÜRICH,
Tel. +41 1 488 2686, Fax. +41 1 481 7730
Taiwan: Philips Semiconductors, 6F, No. 96, Chien Kuo N. Rd., Sec. 1,
TAIPEI, Taiwan Tel. +886 2 2134 2865, Fax. +886 2 2134 2874
Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd.,
209/2 Sanpavuth-Bangna Road Prakanong, BANGKOK 10260,
Tel. +66 2 745 4090, Fax. +66 2 398 0793
Turkey: Talatpasa Cad. No. 5, 80640 GÜLTEPE/ISTANBUL,
Tel. +90 212 279 2770, Fax. +90 212 282 6707
Ukraine: PHILIPS UKRAINE, 4 Patrice Lumumba str., Building B, Floor 7,
252042 KIEV, Tel. +380 44 264 2776, Fax. +380 44 268 0461
United Kingdom: Philips Semiconductors Ltd., 276 Bath Road, Hayes,
MIDDLESEX UB3 5BX, Tel. +44 181 730 5000, Fax. +44 181 754 8421
United States: 811 East Arques Avenue, SUNNYVALE, CA 94088-3409,
Tel. +1 800 234 7381
Uruguay: see South America
Vietnam: see Singapore
Yugoslavia: PHILIPS, Trg N. Pasica 5/v, 11000 BEOGRAD,
Tel. +381 11 625 344, Fax.+381 11 635 777
For all other countries apply to: Philips Semiconductors,
International Marketing & Sales Communications, Building BE-p,
P.O. Box 218, 5600 MD EINDHOVEN, The Netherlands, Fax. +31 40 27 24825
Internet: http://www.semiconductors.philips.com
© Philips Electronics N.V. 1997
SCA56
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.
The information presented in this document does not form part of any quotation or contract, is believed to be accurate and reliable and may be changed
without notice. No liability will be accepted by the publisher for any consequence of its use. Publication thereof does not convey nor imply any license
under patent- or other industrial or intellectual property rights.
Printed in The Netherlands
437027/1200/01/pp24
Date of release: 1997 Nov 19
Document order number:
9397 750 02733